Reversible regeneration of molybdenum carbonyl species on an alumina thin film

The thin alumina film-supported metallic molybdenum model catalyst was prepared by thermal decomposition of MO(CO)6, and CO chemisorption on the catalyst was investigated in-situ by thermal desorption spectroscopy (TDS) and X-ray photoelectron spectroscopy (XPS). The results showed that a molybdenum-carbonyl-like species was formed on the alumina surface at low temperature by high coordination of CO with the surface metallic molybdenum nanoparticles, indicating a reversible regeneration of molybdenum carbonyl on the alumina surface. CO chemisorption on the model catalyst surface caused the Mo 3d XPS peak to shift toward higher binding energy. The formed molybdenum carbonyl species appeared at about 240 K in the TDS. The supported metallic molybdenum nanoparticles were quite different from the bulk molybdenum in chemical properties, which indicated a prominent particle-size effect of the clusters.

An analysis of the effects of symmetrical tilt grain boundaries on the plastic deformation

A numerical investigation on the simple polycrystals containing three symmetrical tilt grain boundaries (GBs) is carried out within the framework of crystal plasticity which precisely considers the finite deformation and finite lattice rotation as well as elastic anisotropy. The calculated results show that the slip geometry and the redistribution of stresses arising from the anisotropy and boundary constraint play an important role in the plastic deformation in the simple polycrystals. The stress level along GB is sensitive to the load level and misorientation, and the stresses along QB are distributed nonuniformly. The GB may exhibit a softening or strengthening feature, which depends on the misorientation angle. The localized deformation bands usually develop accompanying the GB plastic deformation, the impingement of the localized band on the GB may result in another localized deformation band. The yield stresses with different misorientation angles are favorably compared with the experimental results.

纳米Mo膜的光学特性及最小连续膜厚研究

利用Lambda-900分光光度计，在波长为310～1250nm范围内测量了离子束溅射沉积不同厚度纳米Mo膜的反射率和透射率。选定波长为310nm，350nm，400nm，500nm，550nm，632nm，800nm，1200nm时对薄膜的反射率、透射率和吸收率随膜厚变化的关系进行了讨论。实验结果显示，纳米Mo膜的光学特性有明显的尺寸效应。提出将薄膜对光波长为550nm时的反射率和透射率随Mo膜厚度变化关系的交点对应的厚度作为特征厚度，该厚度可认为是纳米Mo膜生长从不连续膜进入连续膜的最小连续膜厚。利用

用不同的Mo靶溅射功率制备Mo／Si多层膜

用磁控溅射法制备了周期厚度和周期数均相同的Mo／Si多层膜，用原子力显微镜和小角X射线衍射分别研究了Mo靶溅射功率不相同时，Mo／Si多层膜表面形貌和晶相的变化。随后在国家同步辐射实验室测量了Mo／Si多层膜的软X射线反射率。研究发现，随着Mo靶溅射功率的增大，Mo／Si多层膜的表面粗糙度增加，Mo的特征X射线衍射峰也增强，Mo／Si多层膜的软X射线峰值反射率先增大后减小。

固氮酶钼铁蛋白金属原子簇的拆卸与组装的研究

将棕色固氮菌(Azotobacter vinelandii)固氮酶钼铁蛋白与邻菲罗啉和O2或邻非罗啉和尿素保温并经Sephadex G-25柱层析，可分别得到部分或高度缺失P—cluster和FcMoco的“不全蛋白”。其中，部分缺失金属原子簇的蛋白与含V、Mn、Cr的重组液重组后，所得相应的重组蛋白的底物还原活性及吸收光谱和圆二色(CD))谱虽均得到明显恢复，但与还原钼铁蛋白[MoFe (R)]相比又不尽相同：与含V重组液重组的蛋白的底物还原特性与VFe蛋白相似，波谱特性与MoFe (R)有所不同;分别与含Mn和Cr重组液重组的蛋白的底物还原特性与MoFe(R)相似，而波谱特性却与MoFe(R)有较大差异。高度缺失金属原子簇的蛋白分别与含Mo、Mn、Cr重组液重组后，所得相应的重组蛋白的乙炔还原活性虽都有明显的恢复，但与MoFe(R)相比仍相差较大;当与含钼重组液重组后，它的吸收光谱、可见CD谱及天然电泳图谱均可得到明显恢复，而紫外CD谱却与其乙炔还原活性一样，只能得到部分恢复。 根据上述实验结果，我们提出：(1)钼铁蛋白的金属原子簇与其构象密切相关;(2)部分或高度缺失金属原子簇的蛋白与重组液重组的机理——“零件组装”的基本内容;(3)钼原子在FeMoco中的可被取代性及不处于中心位置;(4)还原M oFe蛋白中Fe原子的价态不尽相同。

缺失nifZ的棕色固氮菌突变株DJ194的钼铁蛋白研究—纯化、结晶及金属簇的组成与分布

从棕色固氮菌DJ194菌株得到的固氮酶粗提液经DEAE－52、Sephacryl S－200及Q－Sepharose等柱厌氧层析，分离纯化得到nifZ基因缺失的固氮酶MoFe蛋白（ΔnifZ Av1）制备物。通过天然电泳和SDS变性电泳发现早期纯化所得的ΔnifZ Av1制备物中残存相当比例的三个主要污染蛋白：属于热激蛋白60家族（Hsp 60 family）成员的分子伴侣GroEL、糖酵解过程的一个多功能酶——6-磷酸葡萄糖异构酶（6-Phosphate Glucose Isomerase，PGI）及棕色固氮菌细菌铁蛋白（Bacterioferritin，Bfr）。初步鉴定表明，它们分别为由约55kD亚基组成的14聚合体，62kD亚基组成的10聚体和20kD亚基组成的24聚体。首次发现PGI有如此高的聚合体。虽然GroEL和PGI在天然电泳中的迁移率小于ΔnifZ Av1蛋白，但它们的亚基在SDS变性电泳中与ΔnifZ Av1亚基具有相似的迁移率，互相重叠，从而使变性电泳比天然电泳显出更高的ΔnifZ Av1纯度;而细菌铁蛋白虽然不会在变性电泳中污染ΔnifZ Av1，但往往会在ΔnifZ Av1制备物的结晶中优先或较多地结晶出来,从而给它的晶体生长和解析研究带来干扰（Zhao等，2004）。 通过Sephacryl S－200柱洗脱峰收集精度的调整及Q－Sepharose柱的NaCl浓度梯度洗脱，得到了纯度大于90%的ΔnifZ Av1制备物。它的厌氧天然电泳及其免疫印渍（Western blotting），以及SDS-变性凝胶电泳显出，ΔnifZ Av1的电泳迁移率、分子量和亚基组成等均与野生种钼铁蛋白（OP Av1）相似，表明nifZ基因缺失并未改变ΔnifZ Av1的α2β2四聚体构成。ΔnifZ Av1的Mo含量、EPR信号（g≈4.3, 3.65和2.01）和520-660 nm附近的圆二色摩尔消光系数（Δε）也都与OP Av1较相似，从而表明ΔnifZ Av1含有与OP Av1数量相当的具有3/2自旋态的还原FeMoco。然而，ΔnifZ Av1的Fe含量和对底物（C2H2、H+和N2）的还原活性都较低, 分别约为OP Av1的74%和46-50%;而反映P-cluster状况的450nm附近的Δε也明显低于OP Av1。此外，与OP Av1相同的ΔnifZ Av1在g≈2.01的EPR信号却与推测含由双[4Fe-4S]簇组成的P-cluster前体的His-tagged ΔnifZ Av1（Hu等，2004）的信号明显不同。这就表明，ΔnifZ Av1与OP Av1的差别不在于FeMoco的结构、含量和氧还状态，也不在于P-cluster的结构和氧还状态，而仅在于ΔnifZ Av1中P-cluster数目的减少（约一半）。据此推测出与国外提出的His-tagged ΔnifZ Av1模型不同的ΔnifZ Av1(DJ194)的如下结构模型。一个αβ亚基对含有一个FeMoco和一个P-cluster，而另一个αβ亚基对只含FeMoco，其P-cluster区域则是空的。由于nifZ基因的缺失只造成了钼铁蛋白中两个P-cluster中的一个不能组装，因此推测P-cluster的组装可能不是受单一基因产物的影响。根据Lee等（1998）对nifZ产物（NifZ）和nifW产物（NifW）可以形成[NifWx-NifZy]多聚体，并可能是通过同一途径来影响固氮酶的合成的研究，提出NifZ的如下的可能作用机理。[NifWx-NifZy]多聚体影响与P-cluster合成相关的金属簇(如[4Fe-4S])的进入和P-cluster的最终合成，而其中的一个αβ对上的P-cluster的形成可能较多的受到NifZ的影响;nifZ的某些突变或缺失虽然不影响[NifWx-NifZy]多聚体的形成，但对于更依赖于NifZ的那个αβ对上的P-cluster的合成可能会产生不同的影响。 对这一高纯度的ΔnifZ Av1制备物结晶的研究表明，使用Tris缓冲系统的25%PEG 6K/MgCl2晶体培养液可以在较短的晶体培养时间内得到较大的晶体;在一定条件下，pH为7.5和8.3的培养液对出晶数和晶体大小的影响不明显;PEG 6K的浓度与MgCl2的浓度对出晶大小的影响有一定的相关性，即较低的PEG浓度在较低的MgCl2浓度下和较高的PEG浓度搭配较高的MgCl2浓度较易长出较大的晶体。虽然ΔnifZ Av1制备物的纯度达到90%以上，并且在染铁实验中表明其基本不含细菌铁蛋白，但我们在对得到的晶体进行电泳鉴定中仍然发现了一种与以前报导的砖红色晶体不同的深棕红色的细菌铁蛋白晶体，之所以颜色不同可能和所含的铁元素的氧化状态有关。不过在所鉴定的5支结晶管中只在一个管内发现了与固氮酶晶体同时存在的这种细菌铁蛋白晶体，说明通过蛋白纯度的提高减少细菌铁蛋白的含量以及晶体培养条件的优化，细菌铁蛋白晶体形成的几率就可大大降低。

Trimeresurus stejnegeri snake venom plasminogen activator - Site-directed mutagenesis and molecular modeling

The specific plasminogen activator from Trimeresurus stejnegeri venom (TSV-PA) is a serine proteinase presenting 23% sequence identity with the proteinase domain of tissue type plasminogen activator, and 63% with batroxobin, a fibrinogen clotting enzyme from Bothrops atrox venom that does not activate plasminogen. TSV-PA contains six disulfide bonds and has been successfully overexpressed in Escherichia coli (Zhang, Y., Wisner, A., Xiong, Y. L,, and Bon, C, (1995) J. Biol. Chem. 270, 10246-10255), To identify the functional domains of TSV-PA, we focused on three short peptide fragments of TSV-PA showing important sequence differences with batroxobin and other venom serine proteinases. Molecular modeling shows that these sequences are located in surface loop regions, one of which is next to the catalytic site, When these sequences were replaced in TSV-PA by the equivalent batroxobin residues none generated either fibrinogen-clotting or direct fibrinogenolytic activity, Two of the replacements had little effect in general and are not critical to the specificity of TSV-PA for plasminogen. Nevertheless, the third replacement, produced by the conversion of the sequence DDE 96a-98 to NVI, significantly increased the K-m for some tripeptide chromogenic substrates and resulted in undetectable plasminogen activation, indicating the key role that the sequence plays in substrate recognition by the enzyme.

Bombinakinin M gene associated peptide, a novel bioactive peptide from skin secretions of the toad Bombina maxima

A novel 28-amino acid peptide, termed bombinakinin-GAP, was purified and characterized from skin secretions of the toad Bombina maxima. Its primary structure was established as DMYEIKQYKTAHGRPPICAPGEQCPIWV-NH2, in which two cysteines form a disulfide bond. A FASTA search of SWISS-PROT databank detected a 32% sequence identity between the sequences of the peptide and a segment of rat cocaine- and amphetamine-regulated transcript (CART). Intracerebroventricular (i.c.v.) administration of the peptide induced a significant decrease in food intake in rats, suggesting that it played a role in the control of feeding by brain. Analysis of its cDNA structure revealed that this peptide is coexpressed with bombinakinin M, a bradykinin-related peptide from the same toad. Bombinakinin-GAP appears to be the first example of a novel class of bioactive peptides from amphibian skin, which may be implicated in feeding behavior. (C) 2003 Elsevier Science Inc. All rights reserved.