Sequential resonant tunnelling through Landau levels in GaAs/AlAs superlattices

Electron transport in heavily-doped GaAs/AlAs superlattices in parallel electric and magnetic fields is reported. The current-voltage (I-V) characteristic exhibited the feature of negative differential velocity (NDV) and high electric field domain effect at different biases. Under strong magnetic fields, sequential resonant tunnelling through Landau levels in the negative differential velocity regime is observed, which are manifested as oscillations in the conductance-voltage characteristics. (C) 1998 Elsevier Science B.V. All rights reserved.

Theoretical investigation on quantum well lasers with extremely low vertical beam divergence and low threshold current

A specially designed quantum well laser for achieving extremely low vertical beam divergence was reported and theoretically investigated. The laser structure was characterized by two low index layers inserted between the waveguide layers and the cladding layers. The additional layers were intended to achieve wide optical spread in the cladding layers and strong confinement in the active region. This enabled significant reduction of beam divergence with no sacrifice in threshold current density. The numerical results showed that lasers with extremely low vertical beam divergence from 20 degrees down to 11 degrees and threshold current density of less than 131 A/cm(2) can be easily achieved by optimization of the structure parameters. Influences of individual key structure parameters on beam divergence and threshold current density are analyzed. Attention is also paid to the minimum cladding layer thicknesses needed to maintain low threshold current densities and low internal loss. The near and far field patterns are given and discussed. (C) 1998 American Institute of Physics.

ELECTRON-TRANSPORT THROUGH GAALAS BARRIERS IN GAAS

We have analyzed electronic transport through a single, 200-angstrom-thick, Ga0.74Al0.36As barrier embedded in GaAs. At low temperatures and high electric field, the Fowler-Nordheim regime is observed, indicating that the barrier acts as insulating layers. At higher temperatures the thermionic regime provides an apparent barrier height, decreasing with the field, which is equal to the expected band offset when extrapolated to zero field. However, for some samples, the current is dominated by the presence of electron traps located in the barrier. A careful analysis of the temperature and field behavior of this current allows to deduce that the mechanism involved is field-enhanced emission from electron traps. The defects responsible are tentatively identified as DX centers, resulting from the contamination of the barrier by donor impurities.

A Monolithic Integrated Logic Circuit of Resonant Tunneling Diodes and a HEMT

A technology for the monolithic integration of resonant tunneling diodes (RTDs) and high electron mobility transistors (HEMTs) is developed. Molecular beam epitaxy is used to grow an RTD on a HEMT structure on GaAs substrate. The RTD has a room temperature peak-to-valley ratio of 5.2:1 with a peak current density of 22.5kA/cm~2. The HEMT has a 1μm gate length with a-1V threshold voltage. A logic circuit called a monostableto-bistable transition logic element (MOBILE) circuit is developed. The experimental result confirms that the fabricated logic circuit operates successfully with frequency operations of up to 2GHz.

X-Band GaN Power HEMTs with Power Density of 2.23W/mm Grown on Sapphire by MOCVD

The growth,fabrication,and characterization of 0.2μm gate-length AlGaN/GaN HEMTs,with a high mobility GaN thin layer as a channel,grown on (0001) sapphire substrates by MOCVD,are described.The unintentionally doped 2.5μm thick GaN epilayers grown with the same conditions as the GaN channel have a room temperature electron mobility of 741cm2/(V·s) at an electron concentration of 1.52×1016 cm-3.The resistivity of the thick GaN buffer layer is greater than 108Ω·cm at room temperature.The 50mm HEMT wafers grown on sapphire substrates show an average sheet resistance of 440.9Ω/□ with uniformity better than 96%.Devices of 0.2μm×40μm gate periphery exhibit a maximum extrinsic transconductance of 250mS/mm and a current gain cutoff frequency of77GHz.The AlGaN/GaN HEMTs with 0.8mm gate width display a total output power of 1.78W (2.23W/mm) and a linear gain of 13.3dB at 8GHz.The power devices also show a saturated current density as high as 1.07A/mm at a gate bias of 0.5V.

A GaAs-Based MOEMS Tunable RCE Photodetector with Single Cantilever Beam

A GaAs-based micro-opto-electro-mech anical-systems(MOEMS) tunable resonant cavity enhanced(RCE)photodetector with a continuous tuning range of 31nm under a 6V tuning voltage is demonstrated. The single cantilever beam structure is adopted for this MOEMS tunable RCE photodetector. The maximum and minimum peak quantum efficiency during the tuning are 36.9 % and 30. 8 %, respectively. The maximum and minimum full-width-at-halfmaximum (FWHM) are 20nm and 14nm,respectively. The dark current density is 7.46A/m2 without bias.

Design and Realization of Resonant Tunneling Diodes with New Material Structure

A new material structure with Al0.22Ga(>. 78 As/Ino.i5 Gao.ss As/GaAs emitter spacer layer and GaAs/Ino.15-Gao.8ii As/GaAs well for resonant tunneling diodes is designed and the corresponding device is fabricated. RTDs DC characteristics are measured at room temperature. Peak-to-valley current ratio and the available current density for RTDs at room temperature are computed. Analysis on these results suggests that adjusting material structure and optimizing fabrication processes will be an effective means to improve the quality of RTDs.

Room-temperature continuous-wave lasing from InAs GaAs quantum dot laser grown by molecular beam epitaxy

Quantum dot lasers are predicted to have proved lasing characteristics compared to quantum well and quantum wire lasers. We report on quantum dot lasers with active media of vertically stacked InAs quantum dots layers grown by molecular beam epitaxy. The laser diodes were fabricated and the threshold current density of 220 A/cm(2) was achieved at room temperature with lasing wavelength of 951 nm. The characteristic temperature To was measured to be 333K and 157K for the temperature range of 40-180K and 180-300K, respectively.

Design and fabrication of GaAs OMIST photodetector

We designed and fabricated GaAs OMIST (Optical-controlled Metal-Insulator-Semiconductor Thyristor) device. Using oxidation of A1As layer that is grown by MBE form the Ultra-Thin semi-Insulating layer (UTI) of the GAAS OMIST. The accurate control and formation of high quality semi-insulating layer (AlxOy) are the key processes for fabricating GaAs OMIST. The device exhibits a current-controlled negative resistance region in its I-V characteristics. When illuminated, the major effect of optical excitation is the reduction of the switching voltage. If the GaAs OMIST device is biased at a voltage below its dark switching voltage V-s, sufficient incident light can switch OMIST from high impedance low current"off"state to low impedance high current "on"state. The absorbing material of OMIST is GaAs, so if the wavelength of incident light within 600 similar to 850nm can be detected effectively. It is suitable to be used as photodetector for digital optical data process. The other attractive features of GaAs OMIST device include suitable conducted current, switching voltage and power levels for OEIC, high switch speed and high sensitivity to light or current injection.

Sequential resonant tunnelling through Landau levels in GaAs/AlAs superlattices

Electron transport in heavily-doped GaAs/AlAs superlattices in parallel electric and magnetic fields is reported. The current-voltage (I-V) characteristic exhibited the feature of negative differential velocity (NDV) and high electric field domain effect at different biases. Under strong magnetic fields, sequential resonant tunnelling through Landau levels in the negative differential velocity regime is observed, which are manifested as oscillations in the conductance-voltage characteristics. (C) 1998 Elsevier Science B.V. All rights reserved.

Electrical bistability and negative differential resistance in diodes based on silver nanoparticle-poly(N-vinylcarbazole) composites

An electrically bistable device has been fabricated using nanocomposite films consisting of silver nanoparticles and a semiconducting polymer by a simple spin-coating method. The current-voltage characteristics of the as-fabricated devices exhibit an obvious electrical bistability and negative differential resistance effect. The current ratio between the high-conducting state and low-conducting state can reach more than 103 at room temperature. The electrical bistability of the device is attributed to the electric-filed-induced charge transfer between the silver nanoparticles and the polymer, and the negative differential resistance behavior is related to the charge trapping in the silver nanoparticles. The results open up a simple approach to fabricate high quality electrically bistable devices by doping metal nanoparticles into polymer.

Experimental Investigation of Performance of a Miniature Direct Methanol Fuel Cell in Short-Term Microgravity

Experimental study of a liquid fed direct methanol fuel cell has been conducted in different gravity environments. A small single cell with 5 cm x 5 cm active area has single serpentine channel on the graphite cathode polar plate and 11 parallel straight channels on the graphite anode flow bed. Cell voltage and current have been measured and two-phase flow in anode channels has been in situ visually observed. The experimental results indicate that the effect of gravity on power performance of the direct methanol fuel cell is large when the concentration polarization governs fuel cells operation. Gravitational effect becomes larger at higher current density. Increasing methanol feeding molarity is conducive to weaken the influence of gravity on performance of liquid fed direct methanol fuel cells. Increasing feeding flow rate of methanol solution from 6 to 15 ml/min could reduce the size of carbon dioxide bubbles, while the influence of gravity still exist. Transport phenomena inside direct methanol fuel cells in microgravity is also analyzed and discussed.

Field emission from the structure of well-aligned TiO2/Ti nanotube arrays

Well-aligned TiO2/Ti nanotube arrays were synthesized by anodic oxidation of titanium foil in 0.5 wt.% HF in various anoclization voltages. The images of filed emission scanning electron microscopy indicate that the nanotubes structure parameters, such as diameter, wall thickness and density, can be controlled by adjusting the anoclization voltage. The peaks at 25.3 degrees and 48.0 degrees of X-ray diffraction pattern illuminate that the TiO2 nanotube arrays annealed at 500 degrees C are mainly in anatase phase. The filed emission (FE) properties of the samples were investigated. A turn-on electric field 7.8 V/mu m, a field enhancement factors approximately 870 and a highest FE current density 3.4 mA/cm(2) were obtained. The emission current (2.3 mA/cm(2) at 18.8 V/mu m) was quite stable within 480 min. The results show that the FE properties of TiO2/Ti have much relation to the structure parameters.

Preparation of silver nanowires in ion-track membranes

Polycarbonate (PC) membranes were irradiated with swift heavy ions and latent tracks were created along the ions' trajectories. Nanopores, diameters between 100 and 500 nm, were obtained after illuminating the membranes with UV light and etching in NaOH solution. Silver nanowires were produced in the etched ion-track membranes by electrochemical deposition. The morphology and crystallinity of the silver nanowires were studied by means of scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and selected area electron diffraction (SAED). Under certain conditions (deposition voltage 25 mV, current density 1-2 mA.cm(-2), temperature 50 degrees C, electrolyte 0.1 mol.L-1 AgNO3), single-crystalline silver nanowires with preferred orientation along the [111] direction can be synthesized.

Drift distance survey in direct plasma injection scheme for high current beam production

In a laser ion source, plasma drift distance is one of the most important design parameters. Ion current density and beam pulse width are defined by plasma drift distance between a laser target and beam extraction position. In direct plasma injection scheme, which uses a laser ion source and a radio frequency quadrupole linac, we can apply relatively higher electric field at beam extraction due to the unique shape of a positively biased electrode. However, when we aim at very high current acceleration such as several tens of milliamperes, we observed mismatched beam extraction conditions. We tested three different ion current at ion extraction region by changing plasma drift distance to study better extraction condition. In this experiment, C6+ beam was accelerated. We confirmed that matching condition can be improved by controlling plasma drift distance.