Partial and total replacement of fishmeal with poultry by-product meal in diets for gibel carp, Carassius auratus gibelio Bloch

Triplicate groups of gibel carp Carassius auratus gibelio Bloch (initial body weight: 4.89 g) were fed for 8 weeks at 24.8-30.8 degrees C with nine isonitrogenous and isoenergetic diets. The control diet (F1) used white fishmeal (FM) as the sole protein source. In the other eight diets (F2-F9), 40.5-100% of FM protein was substituted by poultry by-product meal (PBM) at 8.5% increments. The specific growth rate (SGR), feed efficiency ratio, protein efficiency ratio, protein retention efficiency and energy retention rate for fish fed PBM diets (F2-F9) were all higher, but not always significantly, than those for fish fed F1. All apparent digestibility coefficients for fish fed PBM diets were lower than those for fish fed F1. Fish fed F1 had a significantly higher hepatosomatic index value than fish fed PBM diets (P < 0.05). No significant (P > 0.05) effect of diet was found in whole-body moisture and fat content. Whole-body protein and energy content for fish fed PBM diets were slightly higher than that for fish fed F1. The optimal replacement level of FM by PBM was estimated by second-order polynomial regression to be 66.5% in protein.

Comparative study on the effect of dietary lipid level on growth and feed utilization for gibel carp (Carassius auratus gibelio) and Chinese longsnout catfish (Leiocassis longirostris Gunther)

An 8-week growth trial investigated the effect of dietary lipid level on growth performance of a carnivorous fish, Chinese longsnout catfish (Leiocassis longirostris Gunther) and an omnivorous fish, gibel carp (Carassius auratus gibelio). For each species, seven isonitrogenous semi-purified diets (455 g kg(-1) crude protein for Chinese longsnout catfish and 385 g kg(-1) crude protein for gibel carp) were formulated to contain 30, 60, 90, 120, 150, 180 or 210 g kg(-1) lipid. For Chinese longsnout catfish, feed intake (FI) decreased with increasing dietary lipid and there was no significant difference in feed intake from 90 to 210 g kg(-1) lipid. Specific growth rate (SGR) increased with dietary lipid level (P < 0.05) and the 150 and 180 g kg(-1) groups were the best. Feed conversion efficiency (FCE), protein retention efficiency (PRE) and energy retention efficiency (ERE) were higher at 180 g kg(-1) lipid. For gibel carp, FI decreased with increased dietary lipid and 180 and 210 g kg(-1) lipid groups showed lower values. SGR increased with dietary lipid level and the 150 and 180 g kg(-1) were the best. FCE was higher at 180 g kg(-1) lipid level. PRE increased with dietary lipid level and there was no significant difference in groups from 120 to 210 g kg(-1) dietary lipid. ERE increased with increasing dietary lipid level, and groups fed 120, 150 and 180 g kg(-1) lipid showed the highest values. In Chinese longsnout catfish, increase in dietary lipid level, resulted in increased carcass dry matter, crude protein, crude lipid and gross energy. In gibel carp, dry matter, crude protein, and crude lipid increased with dietary lipid level. Based on regression between SGR and dietary lipid, dietary lipid requirements for Chinese longsnout catfish and gibel carp were 142.6 and 140.5 g kg(-1), respectively.

Genetic heterogeneity and ploidy level analysis among different gynogenetic clones of the polyploid gibel carp

Background: Some triploid and tetraploid clones have been identified in the gynogenetic gibel carp, Carassius auratus gibelio Bloch, by karyotypic and cytologic analyses over many years. Further, 5-20% males and karyotypic diversity have been found among their natural and artificial populations. However, the DNA contents and the relation to their ploidy level and chromosome numbers have not been ascertained, and whether normal meiosis occurs in spermatogenesis needs to be determined in the different clones. Methods: The sampled blood cells or sperms were mixed with blood cells from chicken or individual gibel carp and fixed in 70% pre-cooled ethanol overnight at 4degreesC. The mixed cell pellets were washed 2-3 times in 1x phosphate buffered saline and then resuspended in the solution containing 0.5% pepsin and 0.1 M HCl. DNA was stained with propidium iodide solution (40 mug/mL) containing 4 kU/ml RNase. The measurements of DNA contents were performed with Phoenix Flow Systems. Results: Triploid clones A, E, F, and P had almost equal DNA content, but triploid clone D had greater DNA content than did the other four triploid clones. DNA content of clone M (7.01 +/- 0.15 pg/nucleus) was almost equal to the DNA content of clone D (5-38 +/- 0.06 pg/nucleus) plus the DNA content of common carp sperm (1.64 +/- 0.02 pg/nucleus). The DNA contents of sperms from clones A, P, and D were half of their blood cells, suggesting that normal meiosis occurs in spermatogenesis. Conclusions: Flow cytometry is a powerful method to analyze genetic heterogeneity and ploidy level among different gynogenetic clones of polyploid gibel carp. Through this study, four questions have been answered. (a) The DNA content correlation among the five triploid clones and one multiple tetraploid clone was revealed in the gibel carp, and the contents increased with not only the ploidy level but also the chromosome number. (b) Mean DNA content was 0.052 pg in six extra chromosomes of clone D, which was higher than that of each chromosome in clones A, E, F, and P (about 0.032 pg/ chromosome). This means that the six extra chromosomes are larger chromosomes. (c) Normal meiosis occurred during spermatogenesis of the gibel carp, because DNA contents of the sperms from clones A, P, and D were almost half of that in their blood cells. (d) Multiple tetraploid clone M (7.01 +/- 0.15 pg/nucleus) contained the complete genome of clone D (5.38 +/- 0.06 pg/nucleus) and the genome of common carp sperm (1.64 +/- 0.02 pg/nucleus). Cytometry Part A 56A:46-52, 2003. (C) 2003 Wiley-Liss, Inc.

Determination of trace level microcystins in water using solid-phase extraction and high performance liquid chromatography

This paper presents a method for trace level analysis of microcystins in water using solid-phase extraction and high performance liquid chromatography. The optimized condition enabled the determination of common microcystins at levels as low as 0.02 similar to 0.05 mug/L, and the liner range is from 0.1 mug/L to 50 mug/L. The method has been applied to the analysis of field sample from Dianchi lake.

Compensatory growth in the gibel carp following feed deprivation: temporal patterns in growth, nutrient deposition, feed intake and body composition

To investigate the nature of compenstory growth in fish, an 8 week study at 28 degreesC was performed on juvenile gibel carp Carassius auratus gibelio weighing 6.6 g. Fish were starved for 0 (control), 1 (Sl)or 2 (S2) weeks and then re-fed to satiation For 5 weeks. Weekly changes in weight gain, feed intake and body composition were monitored during re-feeding. No significant difference was found in final body weight between the three groups, indicating complete compensation in the deprived fish, The deprived groups caught up in body weight with that of the control after 2 weeks of re-feeding. Body fat:lean body mass ratio was restored to the control level within 1 week of re-feeding. In the re-feeding period, weekly gains in body weight, protein. lipid, ash and energy in the S1 group were significantly higher than in the controls for 1 week. For the S2 group, weekly gains in body weight. lipid. ash and energy were higher than in the controls for 2 weeks, and gain in protein was higher than in the controls for 3 weeks, though gain in body energy became elevated again during the last 2 weeks of the experiment. Feed intake remained higher than the control level for 3 weeks in the S1 group and 3 weeks in the SZ group. Growth efficiency was not significantly different among the three groups in any of the weeks during re-feeding. Compensatory responses in growth and especially feed intake tended to last longer than the recovery of body composition. (C) 2001 The Fisheries Society of the British Isles.

Wafer-Level Testable High-Speed Silicon Microring Modulator Integrated with Grating Couplers

A wafer-level testable silicon-on-insulator-based microring modulator is demonstrated with high modulation speed, to which the grating couplers are integrated as the fiber-to-chip interfaces. Cost-efficient fabrications are realized with the help of optical structure and etching depth designs. Grating couplers and waveguides are patterned and etched together with the same slab thickness. Finally we obtain a 3-dB coupling bandwidth of about 60nm and 10 Gb/s nonreturn-to-zero modulation by wafer-level optical and electrical measurements.

Annihilation of deep level defects in InP through high temperature annealing

Deep level transient spectroscopy (DLTS) and thermally stimulated current spectroscopy (TSC) have been used to investigate defects in semi-conducting and semi-insulating (SI) InP after high temperature annealing, respectively. The results indicate that the annealing in iron phosphide ambient has an obvious suppression effect of deep defects, when compared with the annealing in phosphorus ambient. A defect annihilation phenomenon has also been observed in Fe-doped SI-InP materials after annealing. Mechanism of defect formation and annihilation related to in-diffusion of iron and phosphorus is discussed. Nature of the thermally induced defects has been discussed based on the results. (c) 2007 Elsevier Ltd. All rights reserved.

Optical response of high-level bandgap in one-dimensional photonic crystal applying in-plane integration

A new broadband filter, based on the high level bandgap in 1-D photonic crystals (PCs) of the form Si vertical bar air vertical bar Si vertical bar air vertical bar Si vertical bar air vertical bar Si vertical bar air vertical bar Si vertical bar air vertical bar Si is designed by the plane wave expansion method (PWEM) and the transfer matrix method (TMM) and fabricated by lithography. The optical response of this filter to normal-incident and oblique-incident light proves that utilizing the high-level bandgaps of PCs is an efficient method to lower the difficulties of fabricating PCs, increase the etching depth of semiconductor materials, and reduce the coupling loss at the interface between optical fibers and the PC device. (c) 2007 Society of Photo-Optical Instrumentation Engineers.

Deep level defects in high temperature annealed InP

Deep level defects in high temperature annealed semi-conducting InP have been studied by deep level transient spectroscopy (DLTS). There is obvious difference in the deep defects between as-grown InP, InP annealed in phosphorus ambient and iron phosphide ambient, as far as their quantity and concentration are concerned. Only two defects at 0.24 and 0.64 eV can be detected in InP annealed in iron phosphide ambient, while defects at 0.24, 0.42, 0.54 and 0.64 eV have been detected in InP annealed in phosphorus ambient, in contrast to two defects at 0.49 and 0.64 eV or one defect at 0.13 eV in as-grown InP. A defect suppression phenomenon related to iron diffusion process has been observed. The formation mechanism and the nature of the defects have been discussed.

Method for generating maximally entangled states of multiple three-level atoms in cavity QED

We propose a scheme to generate maximally entangled states (MESs) of multiple three-level atoms in microwave cavity QED based on the resonant atom-cavity interaction. In the scheme, multiple three-level atoms initially in their ground states are sequently sent through two suitably prepared cavities. After a process of appropriate atom-cavity interaction, a subsequent measurement on the second cavity field projects the atoms onto the MESs. The practical feasibility of this method is also discussed.

Photoemission study of chemisorption and Fermi-level pinning at K/GaAs(100) interface with synchrotron radiation

The adsorption of K on the n-GaAs(I 0 0) surface was investigated by X-ray photoelectron spectroscopy (XPS) and synchrotron radiation photoemission spectroscopy (SR-PES). The Ga3d and As3d core level was measured for clean and K adsorbed GaAs(I 0 0) surface. The adsorption of K induced chemical reaction between K and As, and the K-As reactant formed when the K coverage theta > I ML. The chemical reaction between K and Ga did not occur, but Ga atoms were exchanged by K atoms. From the data of band bending, the Schottky barrier is 0.70 eV. The Fermi-level pinning was not caused by defect levels. The probable reason is that the dangling bonds of surface Ga atoms were filled by the outer-shell electrons of K atoms, forming a half-filled surface state. The Fermi-level pinning was caused by this half-filled surface state. (c) 2004 Elsevier B.V. All rights reserved.

Level-oscillation-induced pump effect in a quantum dot with asymmetric constrictions

We have investigated the pump effect induced by the level oscillation in a quantum dot with asymmetric constrictions. The curve of pumped current versus the frequency of level oscillation undulates at zero temperature. The oscillation of the pumped current can be smeared by increasing the temperature and the coupling strength between the quantum dot and the leads. Either the temperature increase or the coupling strength enhancement can lead to a positive or negative effect on the pumped current, depending on the parameters of the quantum dot system. A larger level-oscillation magnitude results in a larger pumped current, especially in the low-frequency case. An analytical expression of the pumped current is obtained in the regime far from adiabatic. A convenient physical picture based on our analytic result is proposed, with which we can explain all the features of the pumped current curves.

Generation of a supersinglet of three three-level atoms in cavity QED

We propose a scheme to generate a supersinglet of three three-level atoms in microwave cavity quantum electrodynamics based on the resonant atom-cavity interaction. In the scheme, three three-level atoms in suitable initial states are sequentially sent through three cavities originally prepared in their vacuum states. After an appropriate atom-cavity interaction process, in the subsequent measurement on the third cavity field the atoms are projected onto the desired supersinglet. The practical feasibility of this method is discussed.

Influence of level filling on optical properties of quantum well

In a specially- designed three-barrier-double-well tunneling structure, electron injecting from the emitter in combination with escaping through a resonant-tunneling structure were used to adjust and control the filling of electrons in different subbands. It was observed that the occupation in the first-excited electron state can result in a suppression to quantum confinement Stark effect. Moreover, at very low bias, a series of intrigue photoluminescence peaks appeared as a small quantity of excess electron was filled in the ground state of the quantum well, that cannot be explained by the theory of hand-to-hand transition in the framework of single electron picture.

Effect of inter-level relaxation and cavity length on double-state lasing performance of quantum dot lasers

Double-state lasing phenomena are easily observed in self-assembled quantum dot (QD) lasers. The effect of inter-level relaxation rate and cavity length on the double-state lasing performance of QD lasers is investigated on the basis of a rate equation model. Calculated results show that, for a certain cavity length, the ground state (GS) lasing threshold current increases almost linearly with the inter-level relaxation lifetime. However, as the relaxation rate becomes slower, the ratio of excited state (ES) lasing threshold current over the GS one decreases, showing an evident exponential behavior. A relatively feasible method to estimate the inter-level relaxation lifetime, which is difficult to measure directly, is provided. In addition, fast inter-level relaxation is favorable for the GS single-mode lasing, and leads to lower wetting layer (WL) carrier occupation probability and higher QD GS capture efficiency and external differential quantum efficiency. Besides, the double-state lasing effect strongly depends on the cavity length. (c) 2007 Elsevier B.V. All rights reserved.