148 resultados para YTTRIUM OXYSULFIDE
Resumo:
Nd3+-doped Y2-2x La-2x O-3 (x = 0.08) transparent ceramics were fabricated by conventional fabrication process. Spectroscopic properties of the samples were investigated. The absorption band of Nd3+ : Y1.84La0.16O3 was broad covering the wavelength range 780-850 nm. When doped with 1.5at% Nd3+, the cross sections of the sample at 820 nm and laser diode pumped 808 nm were 1.81 x 10(-20) cm(2) and 1.54 x 10(-20) cm(2), respectively. The strongest emission peak of the sample was centered at 1078 mn with long fluorescent lifetime, broad emission bandwidth and high quantum efficiency. Because of the additive La2O3, the spectroscopic quality parameter (X-Nd) of matrix was' decreased from 1.6 to 0.46, thus the fluorescence branch ratio of F-4(3/2) - (4) I-11/2 transition was increased to 56.82%. These properties of Nd3' : Y1.84La0.16O3 transparent ceramic are benefitial to achieve high efficient laser output and ultrashort modelocked pulse.
Resumo:
由溶胶一凝胶/燃烧合成结合法合成了Nd:YAG(掺钕钇铝石榴石,neodymium—doped yttrium aluminium garnet)粉体,用真空烧结法制备了Nd:YAG透明陶瓷。研究了显微结构随烧结温度和保温时间的变化,并对透明陶瓷的晶界结构和成分分布进行了表征。随着烧结温度的提高和保温时间的延长,Nd:YAG陶瓷的密度增大,晶形发育完整,透过率提高。晶粒内部和晶界的化学组成基本相同。所制备的Nd:YAG透明陶瓷在激光工作波长1064nm的透过率达到75%。
Resumo:
It was first reported the spectral properties of a low-temperature sintered transparent Yb: Y2-2x La-2x O-3 laser ceramics. Yb: Y2-2x La-2x O-3 laser ceramics have broad absorption band and large absorption cross- section of 4.0 x 10(-20) cm(2) at wavelengths 977nm of the highest absorption peak. Its fluorescence lifetime is 1.1 ms, and the emission cross-sections are 1.0 x 10(-20) cm(2) and 0.7 x 10(-20) cm(2) at wavelengths 1033nm and 1077nm, respectively. All the optical properties are similar to those of single crystals.
Resumo:
Spectroscopic properties of Ce-doped yttrium orthoaluminate (Ce:YAlO3 or Ce:YAP) crystals grown by temperature gradient technique (TGT) were investigated, and the effects of the growth conditions on the properties were analyzed.. Methods of optical absorption (OA), photoluminescence (PL), photoluminescence decay (PLD), X-ray excited luminescence (XL) and cathodeluminescence (CL) were used in these investigations. The results showed that the absorption band peak at 202, 394 and 532 nm originated from F and F+ color center induced by the weak reducing growth atmosphere, green emission band near 500 ran derived from Ce3+ -Ce3+ pairs and band at 650 similar to 850 run from some unintentional impurity in crystals.
Resumo:
采用传统陶瓷烧结工艺,在无压还原气氛下低温制备出透明性良好的掺Yb^3+氧化镧钇透明激光陶瓷,测试了其在室温下的吸收光谱、发射光谱和荧光寿命.结果表明,掺Yb^3+氧化镧钇透明激光陶瓷的吸收系数随着Yb^3+掺杂浓度的增加而增大,最强吸收峰974 nm处的吸收截面为0.90~1.12×10^-20 cm^2;主发射峰1 032 nm和1 075 nm处的发射截面分别为1.05×10^-20 cm^2和0.87×10^-20 cm^2; Yb^3+掺杂浓度为5at.%时荧光寿命为1.38 ms,并随Yb^3
Resumo:
采用传统无压烧结工艺制备Nd^3 +掺杂的氧化镧钇透明激光陶瓷,测试了其吸收和荧光光谱.采用Judd-Ofelt理论对Nd^3 +掺杂量为1 .5at %的样品光谱参量进行了计算.根据吸收光谱,拟合得到三个强度参量分别为:Ω2=6 .57×10^-20cm^2,Ω4=2 .04×10^-20cm^2,Ω6=4 .38×10^-20cm^2.根据这三个参量计算了样品的辐射寿命,跃迁几率,荧光分支比,量子效率和品质因子,并对结果作了分析.
Resumo:
用碳酸盐共沉淀法制备一种新的掺钕氧化镧钇(Nd:Y1.84La0.16O3)纳米粉体,得到颗粒细小、均匀、分散性好、粒径为50~60nm的Nd:Y1.84La0.16O3纳米粉体.分别采用Nd:Y1.84La0.16O3纳米粉料和商业粉料,用传统陶瓷无压烧结工艺制备Nd:Y1.84La0.16O3透明陶瓷.Nd:Y1.8vLa0.16O3纳米粉制备的陶瓷样品的组分均匀、几乎不存在第二相,具有较高的透过率.商业粉制备的陶瓷样品因混料不均匀而在晶界处存在部分第二相,降低了陶瓷的透过率.此外,还运用体视学法预测
Resumo:
采用传统无压烧结工艺制备了Er^3+/Yb^3+共掺的氧化镧钇透明陶瓷并对其光谱性能进行了研究.样品具有较大的吸收和发射截面.La2O3的添加使样品的荧光寿命(τs)与玻璃接近,当Yb^3+和Er^3+的掺杂量分别为5at%和0.5at%时,测得τs=9.65ms.这种荧光寿命长、发射截面大和线宽窄的特性有利于微型、可集成化和大功率激光输出的实现.
Resumo:
研究了La2O3对Yb:Y2O3透明陶瓷光谱性能的影响,添加适量La2O3以后,Yb:Y2O3透明陶瓷的吸收峰和发射峰的位置不变,但由于La^3+的离子半径大于Y^3+的离子半径,在Y2O3中引入La^3+离子后,导致Y2O3晶格常数变大,晶场强度变弱,同时降低了Y2O3晶体的有序度,致使发射峰强度有所下降,发射截面变小.过量的№La2O3(x=0.16)造成yb^3+激活离子发射强度明显下降;其荧光寿命在添加La2O3后总体增大45%-60%.
Resumo:
采用提拉法生长了掺Ce、掺Yb和掺Mn的铝酸钇(YAlO3,YAP)晶体,晶体均完整透明,无肉眼可见的气泡、散射和包裹物等宏观缺陷。通过化学腐蚀和同步辐射白光形貌实验检测了YAP晶体中的生长小面缺陷。结果表明:晶体生长过程中,由于凸向熔体的固-液界面,造成了小面生长现象。沿[101]方向生长的YAP晶体中出现的小面为(102),(201),(121)和(121)奇异面。X射线摇摆曲线表征的结果表明:生长小面的存在严重破坏了晶体的微观结构完整性和均匀性,并导致了小角度晶界缺陷的产生。
Resumo:
We report both continuous-wave and passively mode-locked laser actions in a Yb3+-doped gadolinium yttrium oxyorthosilicate Yb:GdySiO(5) (Yb:GYSO) crystal. Continuous-wave (CW) laser operations were compared under different pump conditions with high-power diodes of different wavelengths and fiber cores. CW mode-locking was obtained with a semiconductor saturable absorber mirror.
Resumo:
We report on recent experimental results of the spontaneous antiphase dynamics that occurs in a laser-diode-pumped multimode passively Q-switched microchip Yb:YAG (where YAG is yttrium aluminum garnet) lasers with a saturable absorber GaAs. We observe that the pulse sequence of the first mode characterized by one, two, and three pulses as a group and all the modes display an antiphase state as the pumping ratio rises. We modify the multimode rate equations to account for nonlinear absorption due to GaAs in the presence of spatial hole burning. We perform numerical simulations based on the proposed rate equations and reproduce the observed antiphase state of two and three active modes.
Resumo:
Stoichiometric gadolinium oxide thin films have been grown on silicon (100) substrates with a low-energy dual ion-beam epitaxial technique. Gadolinium oxide shares Gd2O3 structures although the ratio of gadolinium and oxygen in the film is about 2:1 and a lot of oxygen deficiencies exist. Photoluminescence (PL) measurements have been carried out within a temperature range of 5-300 K. The detailed characters of the PL emission integrated intensity, peak position, and peak width at different temperature were reported and an anomalous photoluminescence behavior was observed. The character of PL emission integrated intensity is similar to that of some other materials such as porous silicon and silicon nanocrystals in silicon dioxide. Four peaks relative to alpha band and beta band were observed also. Therefore we suggest that the nanoclusters with the oxygen deficiencies contribute to the PL emission and the model of singlet-triplet exchange splitting of exciton was employed for discussion. (C) 2003 American Institute of Physics.
Resumo:
High quality YSi1.7 layers (chi(min) of Y is 3.5%) have been formed by 60 keV Y ion implantation in Si (111) substrates to a dose of 1.0 x 10(17)/cm(2) at 450 degrees C using channeled ion beam synthesis (CIBS). It shows that, compared to the conventional nonchanneled ion beam synthesis, CIBS is beneficial in forming YSi1.7 layers with better quality due to the lower defect density created in the implanted layer. Rutherford backscattering/channeling and x-ray diffraction have been used to study the structure and the strain of the YSi1.7 layers. The perpendicular and parallel elastic strains of the YSi1.7 epilayer are e(perpendicular to) = -0.67% +/- 0.02% and e(parallel to) = +1.04% +/- 0.08%. The phenomenon that a nearly zero mismatch of the YSi1.7/Si (111) system results in a nonpseudomorphic epilayer with a rather large parallel strain relative to the Si substrate (epsilon(parallel to) = +1.09%) is explained, and the model is further used to explain the elastic strain of epitaxial ErSi1.7 and GdSi1.7 rare-earth silicides. (C) 1998 American Vacuum Society.
Resumo:
本文研究了一种中性萃取剂支链三烷基氧化膦(Cyanex 925)和一种羧酸类萃取剂仲辛基苯氧基取代乙酸(CA-12)萃取稀土元素和钇的热力学性能。探讨了利用CA -12为萃取剂将钇与其他稀土分离的可行性,遵循基础-应用的原则,完成了从龙南离子型矿的浸出液中提取钇的分馏串级模拟实验。在此基础上还进一步研究了“绿色溶剂”离子液为溶剂,CA-12萃取稀土和钇的热力学机理。我们还考察了双水相中氨基酸的分离,为利用双水相体系萃取稀土元素奠定了一定的基础。具体的研究内容如下: 1.系统的研究了Cyanex 925在硝酸体系中萃取稀土和Y的规律,由斜率分析方法确定了反应机理,发现了明显的四分组效应,并确定了Y在萃取中所处的位置。同时发现Cyanex 925有可能用于轻、重稀土分组,易反萃。 2.CA-12对Y萃取具有高的选择性,研究了Y与其他稀土分离的可能性。进行了CA-12从混合稀土中提取Y的工艺模拟实验,并获得纯度为99.5%Y2O3,该工艺高效简便,具有好的应用前景。 3.系统的研究了离子液作为溶剂,CA-12从硝酸介质中萃取稀土和Y的规律。考察了不同水相酸度、水相中相关各种离子及萃取剂浓度变化对CA-12萃取稀土和钇的影响,从而推导了萃取反应方程式及机理。并发现在同样萃取剂浓度和水相条件下,CA-12-离子液体系中萃取稀土和钇的能力低于CA-12-庚烷体系中。 4.研究了赖氨酸、蛋氨酸、苯丙氨酸和半胱氨酸在聚乙二醇(PEG)-磷酸盐双水相体系(ATPSs)中分配行为,分别考察了PEG分子量、水相pH、氨基酸侧链结构等对分配比的影响,得出氨基酸在双水相中的分配行为取决于双水相体系的性质和氨基酸的支链结构与带电情况。