高能Pb离子辐照注碳SiO_2的红外谱研究

室温下,先用120keV的C离子注入二氧化硅薄膜样品至剂量2.0×1017,5.0×1017或8.6×1017ions/cm2,再用950MeV的Pb离子分别辐照至剂量5.0×1011,1.0×1012或3.8×1012ions/cm2,然后测量样品的傅里叶变换红外(FTIR)光谱.通过分析测量得到的傅里叶变换红外谱,发现Pb离子辐照在注碳SiO2样品中可引起大量的Si—C和Si(C)—O—C等化学键的形成,大剂量Pb离子辐照可在大剂量注碳的SiO2中产生分子CO2.大量的Si—C键的存在和分子CO2的形成,预示着高能Pb离子辐照在注碳SiO2样品中有可能形成了纳米Si团簇和/或SiC晶粒.

Prediction of soil organic carbon partition coefficients by soil column liquid chromatography

To avoid the limitation of the widely used prediction methods of soil organic carbon partition coefficients (K-OC) from hydrophobic parameters, e.g., the n-octanol/water partition coefficients (K-OW) and the reversed phase high performance liquid chromatographic (RP-HPLC) retention factors, the soil column liquid chromatographic (SCLC) method was developed for K-OC prediction. The real soils were used as the packing materials of RP-HPLC columns, and the correlations between the retention factors of organic compounds on soil columns (k(soil)) and K-OC measured by batch equilibrium method were studied. Good correlations were achieved between k(soil) and K-OC for three types of soils with different properties. All the square of the correlation coefficients (R-2) of the linear regression between log k(soi) and log K-OC were higher than 0.89 with standard deviations of less than 0.21. In addition, the prediction of K-OC from K-OW and the RP-HPLC retention factors on cyanopropyl (CN) stationary phase (k(CN)) was comparatively evaluated for the three types of soils. The results show that the prediction of K-OC from k(CN) and K-OW is only applicable to some specific types of soils. The results obtained in the present study proved that the SCLC method is appropriate for the K-OC prediction for different types of soils, however the applicability of using hydrophobic parameters to predict K-OC largely depends on the properties of soil concerned. (C) 2004 Elsevier B.V. All rights reserved.

石灰性土壤微生物量碳、氮与土壤颗粒组成和氮矿化势的关系

以黄土高原土壤类型和土壤肥力差异较大的25个农田石灰性耕层土壤为供试土样,研究了土壤微生物量碳(BC)、微生物量氮(BN)与土壤氮素矿化势(N0)、全氮(TN)、有机碳(OC)及土壤颗粒组成的关系.结果表明:BC、BN与TN、OC呈极显著正相关(P<0.01),表明BC、BN与土壤肥力关系密切,可作为评价土壤质量的生物学指标.BC、BN与N0均呈高度正相关,相关系数分别为0.665和0.741(P<0.01).BC、BN、TN、OC、N0与土壤物理性粘粒(<0.01 mm)呈显著或极显著正相关,而与物理性砂粒(>0.01 mm)呈显著或极显著负相关,与物理性粘粒和砂粒比值呈显著或极显著正相关,表明土壤有机质主要通过与土壤物理性粘粒复合而形成有机无机复合体.

黄土高原不同类型旱区苜蓿草地水分生产潜力与土壤干燥化效应模拟

在模型验证和数据库组建基础上,用WinEPIC模型定量模拟研究了黄土高原半湿润区长武、半干旱区固原和半干旱偏旱区海原20～30年内苜蓿草地水分生产潜力、10m土层土壤有效含水量和土壤湿度剖面分布特征的动态变化.结果表明:长武、固原和海原苜蓿草地水分生产潜力模拟值随降水量变化而呈现波动性降低趋势,其平均值分别为8.81、3.83和2.48t.hm-2;长武、固原和海原苜蓿草地10m土层逐月土壤有效含水量模拟值均呈现明显的波动性降低趋势,模拟初期,4～8年生苜蓿草地土壤干燥化趋势十分强烈,此后,随降水量变化长期在较低水平上波动;随着苜蓿生长年限的延长,苜蓿草地土壤干层逐年加深、加厚,长武、固原和海原土壤干层分布深度达到10m所需时间依次为6、6和4年,此后苜蓿草地降水渗深以下土层长期维持较为稳定的干燥化状态;苜蓿草地水分持续利用的合理年限为半湿润区8～10年,半干旱区6～8年,半干旱偏旱区4～6年.

The effect of annealing treatment on performance of interdiffused organic photovoltaic devices

We fabricated the interdiffused organic photovoltaic devices, which composed of poly (2-methoxy-5-(2'-ethylhexyloxy)-1, 4-phenylenevinylene) (MEH-PPV) and buckminsterfullerene (C-60), by annealing treatment. After annealing, C60 diffused into the MEH-PPV layer, in consequence, MEH-PPV/C-60 interfacial area was increased and their interface became closer proximity. The results lead to reduce reverse-bias saturation current (J(s)), and increase the open-circuit voltage (V-OC) and the short-circuit current (J(SC)).

Effects of thermal annealing on polymer photovoltaic cells with buffer layers and in situ formation of interfacial layer for enhancing power conversion efficiency

We have investigated the effects of thermal annealing before and after cathode deposition on poly(3-hexylthiophene)(P3HT)/[6,6]-phenyl C61-butyric acid methyl ester (PCBM) blend photovoltaic cells with different cathode buffer layers. The introduction of cathode buffer layer such as lithium fluoride (LiF) and calcium oxide (CaO) in pre-annealing cells can increase the open-circuit voltage (V-oc) and the power conversion efficiency (PCE). Post thermal annealing after cathode deposition further enhanced the PCE of the cells with LiF/Al cathode.

Exfoliation of Organically Modified Montmorillonite Driven by Molecular Diffusion in Maleated Polypropylene

This work is focused on the factors influencing the intercalation of maleated polypropylene (PPMA) into organically modified montmorillonite (OMMT). Two kinds of PPMA were used to explore the optimal candidate for effective intercalation into OMMT. The grafting degree of maleic anhydride and the viscosity of PPMA have effects on the diffusion of polymer molecules. Moreover, the loading level of surfactant was varied to optimize the modification of montmorillonite because the appropriate loading level can provide a balance between interlayer distance and steric hindrance. The kind of surfactant changes the interaction between OMMT and PPMA, and accordingly the intercalation of PPMA is different, resulting in the discrepancy of the intercalation of PPMA.

A strategy of fabricating exfoliated thermoplastic polyurethane/clay nanocomposites via introducing maleated polypropylene

By reducing the attraction between the platelets of octaclecylammonium chloride modified montmorillonite (OMMT-C18) via pre-intercalation of maleated polypropylene (MAPP), OMMT-C18 was exfoliated in thermoplastic polyurethane (TPU) matrix during melt-mixing. Wide angle X-ray diffraction, transmission electron microscopy and thermogravimetric analysis were used to investigate the microstructure of TPU nanocomposites. Three factors (including introducing sequence, the kind and the content of MAPP) showed important effects on the dispersion degree of OMMT-C18 in TPU matrix. The results confirmed that the pre-intercalation of MAPP was necessary for the exfoliation of OMMT-C18; however, the role of MAPP in TPU nanocomposites was different from that in polypropylene nanocomposites.

Isothermal Crystallization Behavior of Poly(L-lactic acid)/Organo-Montmorillonite Nanocomposites

The isothermal crystallization behavior of poly(L-lactic acid)/organo-montmorillonite nanocomposites (PLLA/OMMT) with different content of OMMT, using a kind of twice-functionalized organoclay (TFC), prepared by melt intercalation process has been investigated by optical depolarizer. In isothermal crystallization from melt, the induction periods (t(i)) and half times for overall PLLA crystallization (100 degrees C <= T-c <= 120 degrees C) were affected by the temperature and the content of TFC in nanocomposites. The kinetic of isothermal crystallization of PLLA/TFC nanocomposites was studied by Avrami theory. Also, polarized optical photomicrographs supplied a direct way to know the role of TFC in PLLA isothermal crystallization process. Wide angle X-ray diffraction (WAXD) patterns showed the nanostructure of PLLA/TFC material, and the PLLA crystalline integrality was changed as the presence of TFC. Adding TFC led to the decrease of equilibrium melting point of nanocomposites, indicating that the layered structure of clay restricted the full formation of crystalline structure of polymer.

Solution-processible multi-component cyclometalated iridium phosphors for high-efficiency orange-emitting OLEDs and their potential use as white light sources

The synthesis and photophysical studies of several multifunctional phosphorescent iridium(III) cyclometalated complexes consisting of the hole-transporting carbazole and fluorene-based 2-phenylpyridine moieties are reported. All of them are isolated as thermally and morphological stable amorphous solids. Extension of the pi-conjugation through incorporation of electron- pushing carbazole units to the fluorene fragment leads to bathochromic shifts in the emission profile, increases the highest oc- cupied molecular orbital levels and improves the charge balance in the resulting complexes because of the propensity of the carbazole unit to facilitate hole transport. These iridium-based triplet emitters give a strong orange phosphorescence light at room temperature with relatively short lifetimes in the solution phase. The photo- and electroluminescence properties of these phosphorescent carbazolylfluorene-functionalized metalated complexes have been studied in terms of the coordinating position of carbazole to the fluorene unit. Organic light-emitting diodes (OLEDs) using these complexes as the solution-processed emissive layers have been fabricated which show very high efficiencies even without the need for the typical hole-transporting layer.I These orange-emitting devices can produce a maximum current efficiency of similar to 30 cd A(-1) corresponding to an external quantum efficiency of similar to 10 % ph/el (photons per electron) and a power efficiency of similar to 14 Im W-1.

硅胶催化的选择性去除N-Boc保护基

叔丁氧羰基(Boc)作为氨基的重要保护基团在有机合成中已有广泛应用[1],其脱保护是通过三氟乙酸来实现的,这种方法具有反应时间短、产率高和适用范围广等优点,但是较强的酸性也容易导致敏感基团的分解,限制了其使用.近年来,许多温和及有选择性的试剂已见报道[2~8],但是这些方法都存在一定的缺陷,难以广泛使用.最近,我们发现在回流的甲苯中,以硅胶为催化剂,多种N-Boc保护的伯胺、仲胺、氨基酸的氨基都可以迅速脱除Boc.该方法具有条件温和、操作简便、反应时间短和产率高等优点.同时,其它常用的保护基Cbz和Fmoc等在同样的条件下不受影响.反应式见Scheme 1和Scheme 2.NR1R2OR1R2OSilica gel,tolueneRefluxNH1a—18a1b—18bNHR NHBocSilica gel,tolueneRefluxNHR NH219a—21a19b—21bS chem e 1 D epro tection ofN-B oc by silica ge lR1=alkyl,aryl;R2=H,alkyl,aryl.S chem e 2 S e lective d epro tection o...

Biodegradable poly(L-lactide)/poly(epsilon-caprolactone)-modified montmorillonite nanocomposites: Preparation and characterization

New nanocomposites were prepared by melt blending poly(L-lactide) (PLLA), poly(epsilon-caprolactone) (PCL), and organically modified montmorillonite (OMMT). The obtained nanocomposites showed enhanced tensile strength, modulus and elongation at break than that of PLLA/PCL blends. The dynamic mechanical analysis showed the increasing mechanical properties with temperature dependence of nanocomposites. Wide-angle X-ray diffraction analysis and transmission electron microscopy indicated that the material formed the nanostructure. Adding OMMT improved the thermal stability and crystalline abilities of nanocomposites. The morphology was investigated by environmental scanning electron microscopy, which showed that increasing content of OMMT reduces the domain size of phase-separated particles. The specific interaction between each polymer and OMMT was characterized by the Flory-Huggins interaction parameter, B, which was determined by the equilibrium melting point depression of nanocomposites. The final values of B showed that PLLA was more compatible with OMMT than PCL.

酞菁铜衍生物LB膜/N-si光伏电池的研究

报道了采用新型酞菁铜衍生物:三特戊基苯氧基对羧基苯氧基酞菁铜(ttc～CuPc)制备LB膜ttc-CuPc/硬脂酸(C_(18))/n-Si光伏电池的结果。测量了电池的光照I—V、暗I—V和光谱响应等特性。在辐照度为100mW/cm~2AMC混合光照射下电池的I_(sc)为240μA/cm~2,V_(oc)为0.33V,观察到反常二极管整流效应并进行了讨论。