Structural properties of polycrystalline silicon films formed by pulsed rapid thermal processing

A novel pulsed rapid thermal processing (PRTP) method has been used for realizing the solid-phase crystallization of amorphous silicon films prepared by PECVD. The microstructure and surface morphology of the crystallized films are investigated by X-ray diffraction (XRD) and atomic force microscopy (AFM). The results indicate that this PRTP is a suitable post-crystallization technique for fabricating large-area polycrystalline silicon films with good structural qualities such as large grain size, small lattice microstain and smooth surface morphology on low-cost substrate.

Fabrication of Novel Superhydrophobic Surfaces and Water Droplet Bouncing Behavior - Part 1: Stable ZnO-PDMS Superhydrophobic Surface with Low Hysteresis Constructed Using ZnO Nanoparticles

A superhydrophobic surface has many advantages in micro/nanomechanical applications, such as low adhesion, low friction and high restitution coefficient, etc. In this paper, we introduce a novel and simple route to fabricate superhydrophobic surfaces using ZnO nanocrystals. First, tetrapod-like ZnO nanocrystals were prepared via a one-step, direct chemical vapor deposition (CVD) approach. The nanostructured ZnO material was characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD) and the surface functionalized by aminopropyltriethoxysilane (APS) was found to be hydrophobic. Then the superhydrophobic surface was constructed by depositing uniformly ZnO hydrophobic nanoparticles (HNPs) on the Poly(dimethylsiloxane) (PDMS) film substrate. Water wettability study revealed a contact angle of 155.4 +/- 2 degrees for the superhydrophobic surface while about 110 degrees for pure smooth PDMS films. The hysteresis was quite low, only 3.1 +/- 0.3 degrees. Microscopic observations showed that the surface was covered by micro- and nano-scale ZnO particles. Compared to other approaches, this method is rather convenient and can be used to obtain a large area superhydrophobic surface. The high contact angle and low hysteresis could be attributed to the micro/nano structures of ZnO material; besides, the superhydrophobic property of the as-constructed ZnO-PDMS surface could be maintained for at least 6 months. (C) Koninklijke Brill NV, Leiden, 2010

Fast plasma sintering deposition of nano-structured silicon carbide coatings

Fast plasma sintering deposition of SiC nano-structured coatings was achieved using a specially designed non-transferred dc plasma torch operated at reduced pressure. Employing the Taguchi method, the deposition parameters were optimized and verified. With the optimized combination of deposition parameters, homogeneous SiC coatings were deposited on relatively large area substrates of Φ50 mm and 50×50 mm with a deposition rate as high as 20 μm/min. Ablation test showed that such coatings can be used as oxidation resistance coatings in high temperature oxidizing environment.

若尔盖高原花湖湖滨湿地甲烷排放研究

若尔盖高原湿地位于青藏高原东北部地区，平均海拔3,400-3,600m，是长江和黄河的自然分水区，区内发育了大面积的草本沼泽以及高寒沼泽化草甸、高寒湖泊。由于它所处的位置海拔高、气候波动较大，并处于我国三大自然区的交错过渡带，因而被认为是我国最为典型的脆弱湿地生态系统之一。由于地处偏远、自然环境条件恶劣等多方面的原因，针对若尔盖湿地的科学研究资料一直以来还非常缺乏。本文对国内外近年来在湿地生态系统甲烷排放过程、研究方法，以及关于湿地生态系统甲烷排放的影响因素进行了综述，并采用静态箱－气相色谱法，从湿地环境格局、湿地甲烷排放等方面，对若尔盖高原典型高寒湖泊湖滨不同类型湿地甲烷排放特征进行了研究，并进一步探讨了影响若尔盖高原高寒湖泊湖滨带甲烷排放的因素。得到如下结果：1．若尔盖高原花湖湖滨湿地在植物生长季（6 至8 月），甲烷排放平均速率为0.315 mg·m-2·h-1；不同月份间甲烷排放速率存在差异，分别为：-0.054、0.471、0.493 mg·m-2·h-1。不同类型湿地甲烷排放速率亦表现出差异，两栖蓼（Polygonum amphibium）湿地、滩涂和藏嵩草（Kobresia tibetica）草甸甲烷排放速率分别为：0.464、0.477、0.005mg·m-2·h-1。2．若尔盖高原花湖湖滨湿地甲烷排放速率与土壤10cm 温度显著相关。土壤温度是影响若尔盖高原花湖湖滨不同类型湿地甲烷排放的重要因素之一。随着土壤温度的升高，土壤微生物活性增强，使土壤中的氧消耗加快，氧化还原电位下降，有利于产甲烷菌的生长，从而增加土壤的甲烷产生量。3．地表水位与若尔盖高原花湖湖滨湿地甲烷排放速率相关性不显著。地表水覆盖，使得湿地土壤缺氧状况得到加强，增强了土壤中产甲烷菌的活性，促进甲烷形成，再通过植物、气泡或扩散的形式释放出土壤。但水层的加深，也使土壤中已产生的甲烷在通过气泡或扩散形式穿越水层时，被氧化的量增加，从而减少了甲烷向大气中的排放。4．植被高度以及植被地上生物量与若尔盖高原花湖湖滨带甲烷排放速率的相关性不显著。植物主要通过凋落物以及根系分泌物的输入为产甲烷菌提供基质，并作为土壤与大气之间的甲烷气体交换的传输途径；与其他环境因素共同影响湿地生态系统甲烷排放。The Zoige wetland on the eastern fringe of Qinghai-Tibetan Plateau, with averagealtitude between 3,400 and 3,600m, is the watershed of Yangtze River and YellowRiver. There are large area of peatland, subalpine meadow and lakes in this region.Due to its high elevation, transitional topology and high fluctuation of climate, theZoige wetlands represent one of the most fragile wetland ecosystems in China. And asa result of remote location and harsh environment conditions, the researches on theZoige wetland are relatively rare, especially the researches on the methane emissionfrom littoral zone of alpine lakes. Variations of methane emission rates as measuredby the method of static chamber – gas chromatography (GC) were detected fromlittoral zone of alpine lake on the Zoige Plateau. Relationships between methaneemission rates and environmental factors were analyzed. It is concluded that:1．The average methane emission rate in the littoral zone of Huahu Lake, ZoigePlateau is 0.315 mg·m-2·h-1, with evident spatial and temporal variations. The littoralzone has different methane effluxes with -0.054, 0.471, and 0.493 mg·CH4·m-2·h-1in June, July and August respectively. Different types of wetland have differentmethane emission rates, with value of 0.464, 0.477, and 0.005 mg·CH4·m-2·h-1 forPolygonum amphibium wetland ( PA ), Shoal ( S ) and Kobresi tibetica meadow ( KT ), respectively.2． The soil temperature at 10cm is significantly correlated with the methane effluxesin littoral zone of Huahu Lake, Zoige Plateau, and which is one of the most important factors influencing the methane emission from this region. The activities of soilmicroorganisms rise under higher soil temperature and increases oxygen consumptionand decreases Eh, which is in favor of the methanogensis, and enhances theproduction of methane in soil.3． The correlation between the standing water and methane effluxes from littoralzone of Huahu Lake is not significant. Because of the standing water, the anaerobicconditions of wetland soil have been enhanced, and are favor to the decomposition oforganic matter. And the anaerobic conditions strengthen the methanogensis’ activities,thus the methane production, which release to the atmosphere by diffusion, ebullitionand aerenchymal plants. With the water level’s increase, more methane produced insoil which is transferred by ebullitions or diffusion are oxidated, thus reduce themethane release to the atmosphere.4． The height and aboveground biomass of vegetation are not significant related tothe methane effluxes from littoral zone of Huahu Lake, Zoige Plateau. The vegetationprovides substrates for methanogensis by litter and root exudates; act as thetransportation way of methane between soil and atmosphere; influence the methaneemission of wetland ecosystems with other environment factors.

Monte Carlo simulation of the neutron detection wall at RIBLL II in HIRFL-CSR

With the construction of the new Radioactive Ion Beam Line in Lanzhou (RIBLL II) which connects the CSRm and the CSRe, an experimental setup for physics research is highly required. A large area neutron detection wall is the main part of the setup. This paper introduced the detection principle of the neutron detection wall and the Monte-Carlo simulation of its design under the environment of the Geant4 toolkit. We presented the final design with the optimized parameters and the performance of the wall.

Characteristics of the sampling paddle modules of neutron wall from the cosmic ray test

In the construction of a large area neutron detector (neutron wall) that is used to detect neutrons at GeV energies, the performances of all the sampling paddle modules prepared for the neutron wall are investigated with a specially designed test bench. Tested by cosmic rays, an average intrinsic time resolution of 222.5 ps is achieved at the center of the modules. The light attenuation length and the effective speed of the light in the module are also investigated.

八单元一维位置灵敏雪崩室

In the experiment of nuclear reaction, it is important to measure the mass, charge, energy and emitted direction of particles. For multiparameter measurement, we must use a detector or a group of detectors which can give the time, energy, and position information. The Large Area position sensitive Ionization Chamber(LAIC) is one of the eight experiment terminals of HIRFL. It is built for researching nuclear reactions from low energy to intermediate energy. It is an excellent equipment for energy measurements and atomic number identification of emitted fragments in this energy region. It is also designed to give the time and position information of the emitted fragments by itself. Obviously, an IC can not supply a good timing signal. Moreover, the mechanical installation is different from the original design by some other reasons. In this case, it is not enough to obtain the correct direction information of the emitted fragments. To obtain good timing signals and the correct direction information, some modifications must be made. It is well known that a PPAC can give us excellent timing signals. It also can be easily built as a position sensitive detector. For this reason, a specially designed PPAC is installed in the entrance of the LAIC. For the different purposes, two types of PPACs were designed and tested. Both are OCTPSACs (OCTunit one dimension Position Sensitive Avalanche Counter). In this paper, both OCTPSACs will be introduced. Based on the requirements of the LAIC, the OCTPSACs consist of eight position sensitive PPACs. Each PPAC has an anode and a cathode. In both cases, the sizes are same. But different type of cathodes are used. In one type of OCTPSAC, its cathode is made of wire plane. It consists of gold-plated tungsten wires with the diameter of 20μm, spaced 0.5 mm apart from each other. The anode is a mylar foil which was evaporated by gold layer with the thickness of 50μg/cm~2 mounted on a printed plate in the shape of rectangle. the thickness of mylar foil is 1.5μm. The gap between anode and cathode is 3mm. The performance of the OCTPSAC has been tested by using a ~(252)Cf source in flowing isobutylene gas at the pressure of 3.4mb. The intrinsic time resolution of 289ps and position resolution of 2 mm have been obtained. In another type of OCTPSAC, the cathode is made of mylar foil, which is composed of gold strip by vacuume evaporation method with a special mask on the mylar foil. The thickness and the width of the gold strip is 50μg/cm~2 and 1.7mm. The strips are spaced 0.3 mm apart from each other. The anode is the same as the former type. We have obtained the time resolution of 296ps and position resolution of 2mm by using ~(241)Am-a source when the gas pressure is 6 mb and high voltage is 600V. The working gas is heptane

25MeV/A~(40)Ar+~(115)In反应中轻粒子发射研究及大面积位置灵敏闪烁探测器的研制

论文分为两个部分。第一部分：研究在25MeV/u ~(40)Ar+~(115)In反应中轻粒子发射机制。实验中，利用研制的轻粒子探测器测量了发射的P、#alpha#能谱。用三源模型拟合了轻粒子能谱，所提取的参数与费米气体模型的计算结果进行比较，分析了发射源形成和衰变的一些特点。第二部分：研制一种大面积幅度、时间、位置灵敏闪烁探测器。它是HIRFL上建成的第一阶段放射性核束物理实验终端的主要设备之一，在首次放射性核束调试中收到良好的效果。本文的目的是用经典理论研究了热核形成及衰变的一些性质，在即将开展的放射性核束物理研究中， 利用研制的大型探测器对经典理论普适性进行检验

塑料闪烁体探测器阵列及RIB中的大面积电离室

本文共分为两个部分： 第一部，详细阐述了闪烁体探测器的原理。介绍了研制的用于HIRFL的TR4终端上的多单元(Phoswich)闪烁体探测器阵列，其目的是测量中能重离子核反应中出射粒子的电荷、能量、位置和粒子达到的时间信息。并给出了在初步测试中取得的结果。测试表明，该探测系统有很好的粒子鉴别能力． 第二部分，介绍了研制的大面积双叠层电离室，它是放射性核素次级束流线实验终端的主要探测设备之一，为次级反应产物提供两个ΔE信号．在首次放射性核束调试中取得了满意的结果.

On the meaning of integration in coastal zone management

This paper discusses the definition and use of the term ‘integrated management’ in the context of coastal and ocean resources. It identifies several components which appear to be needed to establish an integrated management system for a large area subject to multiple use and jurisdiction. It suggests that the basis of integrated management should be a clear articulation of common purpose which addresses long term needs and vision. Once developed, this common purpose should be securely established to provide the setting against which sectoral and agencies managers and the community conduct and co-ordinate their activities.

林地施肥与水肥效益

概述了国内外林地施肥的现状 ,简要论述了氮肥利用效率和水分利用效率在农林业生产中的意义。同时 ,阐述了水肥耦合的研究状况 ,并说明了水肥耦合理论应用于林业生产中以改善黄土高原因水肥不协调而形成大面积低效林的重要意义

Microlenses fabricated by discontinuous dewetting and soft lithography

This letter describes an approach to fabricating microlens arrays with low cost and large area through the combination of discontinuous dewetting and reversible water-ice transition via a soft lithography replica process. Microlenses with different curvature can be tuned by the modulation of the wettability of the substrates. The microlenses fabricated can project clear miniaturized images.

Fabrication of an integrated pixel with an organic light-emitting diode driven by copper phthalocyanine organic thin film transistors

An organic integrated pixel with organic light-emitting diodes (OLEDs) driven by organic thin film transistors (OTFTs) is fabricated by a greatly simplified processing. The OTFTs are based on copper phthalocyanine as the active medium and fabricated on indium-tin-oxide (ITO) glass with top-gate structure, thus an organic integrated pixel is easily made by integrating OLED with OTFT. The OTFTs show field-effect mobility of 0.4 cm(2) /Vs and on/off ratio of 10(3) order. The OLED is driven well and emits the brightness as large as 2100cd/m(2) at a current density of 14.6 mu A/cm(2) at -19.7 V gate voltage. This simple device structure is promising in the future large-area flexible OLED displays.

Enhanced charge collection in polymer photovoltaic cells by using an ethanol-soluble conjugated polyfluorene as cathode buffer layer

We report enhanced polymer photovoltaic (PV) cells by utilizing ethanol-soluble conjugated poly (9, 9-bis (6'-diethoxylphosphorylhexyl) fluorene) (PF-EP) as a buffer layer between the active layer consisting of poly(3-hexylthiophene)/[6, 6]-phenyl C61-butyric acid methyl ester blend and the Al cathode. Compared to the control PV cell with Al cathode, the introduction of PF-EP effectively increases the shunt resistance and improves the photo-generated charge collection since the slightly thicker semi-conducting PF-EP layer may restrain the penetration of Al atoms into the active layer that may result in increased leakage current and quench photo-generated excitons. The power conversion efficiency is increased ca. 8% compared to the post-annealed cell with Al cathode.

Micropatterning of polymeric semiconductor by selective lift-off method using epoxy mold

A simple and efficient method for patterning polymeric semiconductors for applications in the field of organic electronics is proposed. The entire polymer layer, except for the desired pattern, is selectively lifted off from a flat poly(dimethylsiloxane) (PDMS) stamp surface by an epoxy mold with a relief pattern. This is advantageous because the elastic deformation of the PDMS stamp around protrusions of a patterned stamp under pressure can assist the plastic deformation of a polymer film along the pattern edges, yielding large area and high quality patterns, and the PDMS surface has low surface energy, which allows the easy removal of the polymer film.