Biomimetic pattern recognition for speaker-independent speech recognition

In speaker-independent speech recognition, the disadvantage of the most diffused technology ( Hidden Markov Models) is not only the need of many more training samples, but also long train time requirement. This paper describes the use of Biomimetic Pattern Recognition (BPR) in recognizing some Mandarin Speech in a speaker-independent manner. The vocabulary of the system consists of 15 Chinese dish's names. Neural networks based on Multi-Weight Neuron (MWN) model are used to train and recognize the speech sounds. Experimental results are presented to show that the system, which can carry out real time recognition of the persons from different provinces speaking common Chinese speech, outperforms HMMs especially in the cases of samples of a finite size.

A practical package technique for FBG-based temperature independent sensor

A practical package technique for temperature independent Fiber Bragg grating sensor is proposed. A uniform strength cantilever with two FBG attached on the upper and lower surfaces was utilized as the key element. By detecting two wavelengths differential output, the applied force can be obtained and temperature effects can be eliminated. Experiment results show the sensor has linear response and output signal uctuates less than 12pm as temperature changes from -10 degrees C to 50 degrees C. The maximum thermal error is less than 0.3% of the full measurement range.

A novel low-power input-independent MOS AC/DC charge pump

This paper presents a novel fully integrated MOS AC to DC charge pump with low power dissipation and stable output for RFID applications. To improve the input sensitivity, we replaced Schottky-diodes in conventional charge pumps with MOS diodes with zero threshold, which has less process defects and is thus more compatible with other circuits. The charge pump in a RFID transponder is implemented in a 0.35um CMOS technology with 0.24 sq mm die size. The analytical model of the charge pump and the simulation results are presented.

Selective and lithography-independent fabrication of 20 nm nano-gap electrodes and nano-channels for nanoelectrofluidics applications

A new method has been developed to selectively fabricate nano-gap electrodes and nano-channels by conventional lithography. Based on a sacrificial spacer process, we have successfully obtained sub-100-nm nano-gap electrodes and nano-channels and further reduced the dimensions to 20 nm by shrinking the sacrificial spacer size. Our method shows good selectivity between nano-gap electrodes and nano-channels due to different sacrificial spacer etch conditions. There is no length limit for the nano-gap electrode and the nano-channel. The method reported in this paper also allows for wafer scale fabrication, high throughput, low cost, and good compatibility with modern semiconductor technology.

Fully lithography independent fabrication of nanogap electrodes for lateral phase-change random access memory application

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-06-07T01:33:41Z No. of bitstreams: 1 ApplPhysLett_96_213505.pdf: 1153920 bytes, checksum: 69931d8deb797813dd478b5dd0e292c0 (MD5)

Lithography-independent and large scale fabrication of a metal electrode nanogap

A lithography-independent and wafer scale method to fabricate a metal nanogap structure is demon-strated. Polysilicon was first dry etched using photoresist (PR) as the etch mask patterned by photolithography.Then, by depositing conformal SiO_2 on the polysilicon pattern, etching back SiO_2 anisotropically in the perpendic-ular direction and removing the polysilicon with KOH, a sacrificial SiO_2 spacer was obtained. Finally, after metal evaporation and lifting-off of the SiO_2 spacer, an 82 nm metal-gap structure was achieved. The size of the nanogap is not determined by the photolithography, but by the thickness of the SiO_2. The method reported in this paper is compatible with modern semiconductor technology and can be used in mass production.

Wide-Band Polarization-Independent Semiconductor Optical Amplifier Gate with Tensile-Strained Quasi-Bulk InGaAs

A semiconductor optical amplifier gate based on tensile-strained quasi-bulk InGaAs is developed. At injection current of 80mA,a 3dB optical bandwidth of more than 85nm is achieved due to dominant band-filling effect.Moreover, the most important is that very low polarization dependence of gain (＜0. 7dB),fiber-to-fiber lossless operation current (70～90mA) and a high extinction ratio (＞50dB) are simultaneously obtained over this wide 3dB optical bandwidth (1520～1609nm) which nearly covers the spectral region of the whole C band (1525～1565nm)and the whole L band (1570～ 1610nm). The gating time is also improved by decreasing carrier lifetime. The wideband polarization-insensitive SOA-gate is promising for use in future dense wavelength division multiplexing (DWDM) communication systems.

Dynamics of morphological changes for mitochondrial fission and fusion

Mitochondria experience continuous fusion and fission in a living cell, but their dynamics remains poorly quantified. Here a theoretical model was developed, upon a simplified population balance equation (PBE), to predict the morphological changes induced by mitochondrial fission and fusion. Assuming that both fission and fusion events are statistically independent, the survival probability of mitochondria staying in the fission or fusion state was formulated as an exponentially-decayed function with time, which depended on the time-dependent distribution of the mitochondrial volume and the fission and fusion rates. Parametric analysis was done for two typical volume distributions. One was Gamma distribution and the other was Gaussian distribution, derived from the measurements of volume distribution for individual mitochondria in a living cell and purified mitochondria in vitro. The predictions indicated that the survival probability strongly depended on morphological changes of individual mitochondria and was inversely correlated to the fission and fusion rates. This work provided a new insight into quantifying the mitochondrial dynamics via monitoring the evolution of the mitochondrial volume.

中国西部亚热带常绿阔叶林木本植物小枝功能生态学初步研究

常绿阔叶林以其富饶的生物资源、丰富的生物多样性和巨大的生态与环境效益引起了人们越来越大的重视，它的研究已成为国际植被科学界关注的主题之一。我国分布着世界上面积最大的亚热带常绿阔叶林，在世界植被中具有重要地位，它的分布表现出明显的地带性差异，存在着多样的植物群系及其对应的气候特征。但是在植物功能性状领域，与全球范围其它生物群系相比，常绿阔叶林物种的研究较少，其功能性状间、功能性状与环境间的关系尚不清晰。 本研究以常绿阔叶林木本植物的当年生小枝为对象，试图从小枝水平上的生物量分配格局、叶片大小与数量的权衡关系、小枝茎的构型效应、叶片元素化学计量学，以及小枝大小的成本与效益分析等方面，较为系统地揭示小枝水平上的植物功能性状间及其与气候间的关系。因此，在华西雨屏带内部的不同纬度设置峨眉－青城－雷波－平武的温度梯度进行比较，并对有降水差异的川西南偏湿性（雷波）与偏干性常绿阔叶林（西昌）进行对比研究，同时在不同山体进行不同海拔梯度的比较研究。 本文主要研究结果如下： （1）小枝生物量分配格局叶水平上，叶片重－叶柄重（Y轴vs.X轴,下同）呈斜率小于1的异速生长关系，表明叶柄对叶内部的生物量分配影响显著。小枝水平上，叶和茎的生物量以及它们与小枝总生物量间基本呈等速生长关系，表明大的小枝或大叶物种不一定在叶生物量的分配上占优势。不同生活型间，在小枝或者茎的生物量一定时，常绿物种叶片的生物量比例较落叶物种稍高。与温度和水分较优越（峨眉及其低海拔）的生境相比，在相对低湿（螺髻）与低温（平武）的生境中的植物会减少对叶的投入而增加对支撑部分的投资比例。 （2）小枝叶片大小与数量的权衡无论是不同气候带还是不同生活型以及不同海拔梯度，叶片大小与出叶强度基本都是呈负的等速生长关系，表明了叶片大小－数量在小枝水平上的权衡。在不同气候梯度的对比中，叶片数量（出叶强度）一定时，高温和高水分生境（峨眉）比低温（平武）和低湿（螺髻山）生境中的物种的叶片大小（质量和面积）更大，表明不同生境的比较中，小的叶片可能具有较高的出叶强度和更高的适合度收益。“出叶强度优势”（Leafingintensitypremium）假说可能不适宜解释不同生境物种叶片大小差异。 （3）小枝茎的构型效应虽然茎长和茎径与叶片大小都呈正相关关系，与出叶强度都呈负相关关系，但茎长/茎径比与叶/茎生物量之比呈负相关关系；与叶片的大小呈负相关关系，与出叶强度呈正相关关系。这说明小枝构型能影响小枝叶/茎生物量分配和叶大小－数量的权衡关系。其影响机制可能是小枝内部的顶端优势。另外，茎长/茎径比在低湿和低温等不利生境中的植物中较高，而在降水和温度较适宜环境中较低。 （4）叶片C、N、P化学计量学N含量和P含量，C/N比和比叶重（LMA,leafmassperarea）呈正的等速生长关系，而N和LMA，P和LMA呈负的等速生长关系。在LMA一定时，C/N比随着生境胁迫压力的增加而降低，N、P含量随着生境压力的增加而增加。在P含量一定时，N含量随着生境压力的增加而降低，即N/P比在生境条件较优（峨眉及其低海拔）时较高。常绿和落叶植物叶片的N/P比没有差异，在LMA一定时，常绿植物的N、P含量较高、C/N比较低。总之，植物的C、N、P化学计量学特征受叶片属性如LMA与气候，及其相互作用的影响。 （5）小枝大小的代价与效益分析、TLA与小枝总重总叶面积（TLA,totalleafarea，Y轴，下同）与总叶重（X轴）均呈斜率小于1的异速生长关系，TLA与小枝横切面积呈斜率为1的等速生长关系。表明叶片面积的增加总是小于叶重和小枝总重的增加，随着小枝的增大，它的叶面积支撑效率下降。在热量和降水优越的生境（峨眉及其低海拔）中，相同小枝重或者相同茎横切面积的小枝，其叶面积支撑效率较低湿与低温环境下（螺髻山、平武及高海拔）的高。 总体上，本文初步研究了小枝水平上可能存在的以下三种权衡关系：叶－茎生物量分配权衡；叶片大小－数量的权衡；小枝茎长－茎径的权衡关系，以及气候要素等对这三种权衡关系的影响。在此基础上，我们还讨论了这些权衡关系的可能形成机制，及其与物种生态适应的联系。本研究丰富了生活史对策中关于权衡关系的研究内容，为我国常绿阔叶林功能生态学研究积累了材料。 Evergreen broad-leaved forests are attracting much more attention from vegetation ecologists than ever before because of their abundant nature resource and biological diversity, and also great ecological benefits. China has the largest distribution of subtropical evergreen broad-leaved forests (temperate rainforests) that are typical and representative in the world. The forests span over more than ten degrees in latitude and more than 30 degrees in longitude, providing an ideal place to study plant functional ecology, i.e., the climatic effect on plant functional traits and the relationship between the traits. However, relative to the other biomes, there are few studies addressing functional ecology of the plant species from subtropical evergreen broad-leaved forests. In this study, I focused on the leaf size-twig size spectrum of the woody species of subtropical evergreen broad-leaved forests in southwestern china. I collected data on leaf size and number, twig size in terms of both mass and volume, and stem architecture from five temperate mountains, and then I analyzed the relationships between leaf and stem biomass and between leaf size and number, the effect of stem length/diameter ratio on biomass allocation and on the relationship between leaf size and number, leaf C:N:P stoichiometry, and the twig efficiency of supporting leaf area in relation to twig size. I also addressed the climate effect on the spectrum. The temperature gradient from warm to cool sites was represented by Emei Mountain, Qingchengshan, Leibo, and Pingwu, and the rainfall gradient was assumed to emerge from the comparison between Leibo (High) and Luojishan (Low). In addition, altitudinal effects were analyzed with comparisons between low and high altitudes for each mountains. My main results are as follows. Isometric relationships were found between leaf mass and twig mass and between lamina mass and twig mass, suggesting that the biomass allocation to leaves or laminas was independent of twig mass. Petiole mass disproportionably increase with respect to lamina mass and twig mass, indicating the importance of leaf petioles to the within-twig biomass allocation. In addition, the investigated species tended to have a larger leaf and lamina mass, but a smaller stem mass at a given twig mass at favorable environments including warm and humid sites or at low altitude than unfavorable habitats, which might be due to the large requirements in physical support and transporting safety for the species living at unfavorable conditions. Moreover, the evergreen species invested more in leaves and laminas than the deciduous at given stem or twig biomass within any specified habitats. Negative, isometric scaling relationships between leaf number and size broadly existed in the species regardless of climate, altitude, and life forms, suggesting a leaf size/number trade-off within twigs. Along the climatic gradients, at given leaf number or leafing intensity, the leaves were larger in the favorable environments than the poor habitats. This suggested that the fitness benefit gained by small leaves could be larger than that with high leafing intensity in the stressful sites. I concluded that the “leafing intensity premium” hypothesis was not appropriate to interpreting between-habitat variation in leaf size. Both stem length and diameter were positively correlated to leaf size but negatively correlated to leafing intensity. The ratio of stem length to diameter was negatively correlated to leaf mass fraction, and it was negatively correlated to leaf size but positively correlated to leafing intensity. This suggested that the stem architecture influenced twig biomass allocation and the relationship between leaf size and number. The mechanism underlying the architectural effect might lie in the apical dominance within twig. Moreover, the ratio was greater in unfavorable habitats but smaller in favorable environments. Positive, isometric relationships were found between N and P contents per leaf mass, and between C/N ratio and leaf mass per area (LMA), but N and P contents scaled negatively to LMA. C/N ratio decreased but N and P increased with increasing habitat stress at a given LMA. N content declined with increasing habitat stress at given P content. These indicated that N/P and C/N were higher but LMA was lower in favorable habitats than in the other circumstances. The evergreen and deciduous species were non-heterogeneous in N/P, but the evergreen species have higher N and P contents and lower C/N than the deciduous ones. In general, C:N:P stoichiometry were related to both climatic conditions and other important functional traits like LMA. Total leaf area (TLA) allometricly scaled to leaf mass with a slope shallower than 1, similar to the relationship between TLA and total twig mass (leaf mass plus stem mass), suggesting that TLA failed to keep pace with the increase of leaf mass and twig size. However, TLA scaled isometricly to twig cross-sectional area. Thus, it could be inferred that the twig efficiency of displaying leaf area decreased with increasing twig size. In addition, the efficiency at a given twig size was large in favorable than unfavorable habitats. In general, in this preliminary study, I studied three tradeoff relationships within twigs, i.e., between leaf and stem biomass, between leaf number and size, and between stem length and diameter, as well as the climatic effect on the relationships. I discussed the mechanisms underlying the tradeoff relationships in view of biophysics and eco-physiology of plants. I believe that this study can serve as important materials advancing plant functional ecology of subtropical forest and that it will improve the understanding of life history strategies of plants from this particular biome.

Rare-Earth Metal Bis(alkyl)s Supported by a Quinolinyl Anilido-Imine Ligand: Synthesis and Catalysis on Living Polymerization of epsilon-Caprolactone

The tridentate ligand N-(2-((2,6-diisopropylphenylimino)methyl)phenyl)quinolin-8-amine (HL) was prepared. Treatment of HL with 1 equiv of Ln(CH2SiMe3)(3)(THF)(2) afforded the corresponding rare-earth metal bis(alkyl) complexes LLn(CH2SiMe3)(2)(THF)(n) (Ln = Sc, n = 0 (1); Y, n = 1 (2); Lu, n = 0 (3)) in high yields. Variable-temperature H-1 NMR spectral analysis showed that these complexes were fluxional at room temperature. Complexes 1 and 3 were THF-free, where the metal center adopted a square-pyramidal geometry, while in 2 the metal center generated a distorted octahedral geometry owing to the coordination of a THF molecule.