A plasma channel scheme for the interaction of an intense femtosecond laser pulse with a deuterium cluster jet

We propose a plasma channel scheme to obtain an improved table-top laser driven fusion neutron yield as a result of explosions of large deuterium clusters irradiated by an intense laser pulse. A cylindrical plasma channel is created by two moderate intensity laser prepulses at the edge of a deuterium cluster jet along which an intense main laser pulse propagates several nanoseconds later. With the aid of this plasma channel, the main laser pulse will be allowed to deposit its energy into the central region of the deuterium gas jet where the cluster sizes are larger and the atomic density is higher. The plasma channel formation and its impact on the deuterium ion energy spectrum and the consequent fusion neutron yield have been investigated. The calculated results show that a remarkable increase of the table-top laser driven fusion neutron yield would be expected.

基于强激光辐照固体锡靶产生极紫外光源的实验研究

建立了一套利用高功率YAG激光器辐照固体锡靶产生高转换效率极紫外光(extreme ultraviolet)源的实验装置.利用建立的实验装置开展了极紫外光源的强度和转换效率与抽运激光强度关系的实验研究,发现极紫外光源的转换效率随抽运激光强度的变化具有饱和效应.实验发现:当抽运激光能量达到250mJ时,极紫外光源的转换效率最高,波长为13.5nm处0.27nm带宽范围内的极紫外光源的能量转换效率为1.6%,此时对应的激光强度为1.8×1011W/cm2.

Standing ultrashort relativistic solitons in overdense plasmas

By using a one-dimensional self-consistent relativistic fluid model, an investigation is made numerically on relativistic electromagnetic solitons with a high intensity in cold overdense plasmas with an electrons' initial velocity opposite to the laser propagating direction. Two types of standing solitons with zero group velocity are found at the given electrons' initial velocities. One is single-humped with a weakly relativistic intensity; the another is multi-humped with a strong relativistic amplitude. The properties of these two types of solitons are presented in detail.

Electron acceleration by a propagating laser pulse in vacuum

Electrons accelerated by a propagating laser pulse of linear or circular polarization in vacuum have been investigated by one-dimensional particle-in-cell simulations and analytical modeling. A stopping target is used to stop the laser pulse and extract the energetic electrons from the laser field. The effect of the reflected light is taken into account. The maximum electron energy depends on the laser intensity and initial electron energy. There is an optimal acceleration length for electrons to gain maximum energy where electrons meet the peak of the laser pulse. The optimal acceleration length depends strongly on the laser pulse duration and amplitude. (C) 2007 American Institute of Physics.

二元振幅型面板用于光束空间整形

为了提高高功率激光系统的整体效率和充分利用光能,需要对前端注入的高斯光束进行空间整形,实现驱动器终端激光的均匀化输出。采用振幅型二元面板对激光光束进行空间强度整形,利用误差扩散法进行了理论设计,数值摸拟了整形效果,同时讨论了面板加工误差以及空间滤波器的小孔大小等因素带来的影响。根据理论设计,分别加工了反高斯透射率分布和抛物线透射率分布的二元面板,并进行了整形实验,实现了各自的整形功能,并做了误差分析。实验证明二元面板能对激光光束的空间强度分布实现了精确的整形。

110-W fiber laser with homemade double-clad fiber

A high-power ytterbium-doped fiber laser (YDFL) with homemade double-clad fiber (DCF) is introduced in this letter. The geometric parameter and laser characteristics of the fiber have been studied. With one-end-pumping scheme, pumped by a high-power laser diode with launching power of 280 W, a maximum continuous wave (CW) output of 110 W is obtained with an optical-to-optical efficiency of 40%.

Comparison of Yb-doped fiber laser with one-end and double-end pumping configuration

A high-power Ytterbium-doped fiber laser (YDFL) with homemade double clad fiber (DCF) is introduced in this paper. The output power characteristics of a linear cavity fiber laser have been studied theoretically by solving the rate equations and experimentally tested with single- and double-end-pumping configurations. When both ends of the fiber are pumped by two high-power laser diodes with a launched power of similar to 300 W each, a maximum CW output of 444 W is obtained with a slope efficiency of similar to 75%. (c) 2006 Elsevier Ltd. All rights reserved.

Low-threshold and continuously tunable Yb : Gd2SiO5 laser

Yb:Gd2SiO5 (Yb:GSO) exhibits a large fundamental manifold splitting. Its long-wavelength emission band around 1088 nm, which has the largest emission cross section, encounters the lowest reabsorption losses caused by thermal population of the terminal laser level. As a result, low-threshold and tunable continuous-wave Yb:GSO lasers were demonstrated. A slope efficiency up to 86% and a pumping threshold as low as 127 mW were achieved for a continuous-wave Yb:GSO laser at 1092.5 nm under the pump of a high-brightness laser diode. A continuous tunability between 1000 and 1120 nm was realized with an SF14 prism as the intracavity tuning element. (c) 2006 American Institute of Physics.

Investigation of damage threshold to TiO2 coatings at different laser wavelength and pulse duration

Laser-induced damages to TiO2 single layers and TiO2/SiO2 high reflectors at laser wavelength of 1064 nm, 800 run, 532 urn, and pulse width of 12 ns, 220 ps, 50 fs, 8 ns are investigated. All films are prepared by electron beam evaporation. The relations among microstructure, chemical composition, optical properties and laser-induced damage threshold (LIDT), have been researched. The dependence of damage mechanism on laser wavelength and pulse width is discussed. It is found that from 1064 nm to 532 nm, LIDT is mainly absorption related, which is determined by film's extinction coefficient and stoichiometric defects. The rapid decrease of LIDT at 800 nm is due to the pulse width factor. TiO2 coatings are mainly thermally by damaged at long pulse (tau >= 220 ps). The damage shows ablation feature at 50 fs. (C) 2007 Elsevier B.V. All rights reserved.

Novel coupled multi-active region high power semiconductor lasers cascaded via tunnel junction

A novel semiconductor laser structure is put forward to resolve the major difficulties of high power laser diodes. In this structure, several active regions are cascaded by tunnel junctions to form a large optical cavity and to achieve super high efficiency. This structure can solve the problems of catastrophic optical damage of facet, thermal damage and poor light beam quality effectively. Low-pressure metalorganic chemical vapor deposition method is adopted to grow the novel semiconductor laser structures, which are composed of Si:GaAs/C:GaAs tunnel junctions, GaAs/InGaAs strain quantum well active regions. External differential quantum efficiency as high as 2.2 and light power output of 2.5 W per facet (under 2A drive current) are achieved from an uncoated novel laser device with three active regions.

Beam dynamics design of an RFQ for a planned accelerator, which uses a direct plasma injection scheme

To meet the requirements of providing high-intensity heavy ion beams the direct plasma injection scheme (DPIS) was proposed by a RIKEN-CNS-TIT collaboration. In this scheme a radio frequency quadrupole (RFQ) was joined directly with the laser ion source (LIS) without a low-energy beam transport (LEBT) line. To find the best design of the RFQ that will have short length, high transmission efficiency and small emittance growth, beam dynamics designs with equipartitioning design strategy and with matched-only design strategy have been performed, and a comparison of their results has also been done. Impacts of the input beam parameters on transmission efficiency are presented, too. (C) 2008 Elsevier B.V. All rights reserved.

细粒沉积物多组分粒度特征及其成因机制研究

By using high-resolution laser grain size instrument Mastersizer 2000, the grain size distribution of windblown depositions (loess and sandy dunes), aqueous sediments (lake, river, riverside and foreshore sand), weathering crust, sloping materials and other fine-grain sediments are systemically measured. The multimodal characteristics of grain size distribution of these sediments are carefully studied. The standard patterns and their grain size characteristics of various sediments are systemically summarized. The discrepancies of multimodal distribution among windblown depositions, aqueous sediments and other sediments are concluded and the physical mechanisms of grain size multimodal distribution of various sediments are also discussed in this paper. The major conclusions are followed: 1. The multimodal characteristic of grain size distribution is a common feature in all sediments and results from properties of transportation medium, dynamic intensity, transportation manner and other factors. 2. The windblown depositions are controlled by aerodynamic forcing, resulting in that the median size of the predominant mode gradually decreases form sandy dunes to loess. Similarly, the aqueous sediments are impacted by dynamic forces of water currents and the median grain size of the predominant mode decreases gradually from river to lake sediments. Because the kinetic viscidity of air is lower than of water, the grain size of modes of windblown depositions is usually finer than that of corresponding modes of aqueous sediments. Typical characteristics of sediments grain size distribution of various sediments have been summarized in the paper: (1) Suspended particles which diameters are less than 75μm are dominant in loess and dust. There are three modes in loess’ grain size distribution: fine, median and coarse (the median size is <1μm、1-10μm、10-75μm, respectively). The coarse mode which percentage is larger than that of others is controlled by source distance and aerodynamic intensity of dust source areas. Some samples also have a saltation mode which median size is about 300-500μm. Our analysis demonstrates that the interaction of wind, atmospheric turbulence, and dust grain gravity along the dust transportation path results in a multimodal grain size distribution for suspended dust. Changes in the median sizes of the coarse and medium modes are related to variation in aerodynamic forcing (lift force related to vertical wind and turbulence) during dust entrainment in the source area and turbulence intensity in the depositional area. (2) There is a predominant coarse saltation mode in grain size distribution of sandy dunes, which median size is about 100-300μm and the content is larger than that of other modes. The grain size distribution curve is near axis symmetric as a standard logarithm normal function. There are some suspended particles in some samples of sandy dunes, which distribution of the fine part is similar to that of loess. Comparing with sandy samples of river sediments, the sorting property of sandy dunes is better than of river samples although both they are the saltation mode. Thus, the sorting property is a criterion to distinguish dune sands and river sands. (3) There are 5~6 modes (median size are <1μm, 1-10μm, 10-70μm, 70-150μm, 150-400μm, >400μm respectively) in grain size distribution of lacustrine sediments. The former 4 modes are suspensive and others are saltated. Lacustrine sediments can be divided into three types: lake shore facies, transitional facies and central lake facies. The grain size distributions of the three facies are distinctly different and, at the same time, the transition among three modes is also clear. In all these modes, the third mode is a criteria to identify the windblown deposition in the watershed. In lake shore sediments, suspended particles are dominant, a saltation mode sometimes occurs and the fourth mode is the most important mode. In the transitional facies, the percentage of the fourth mode decreases and that of the second mode increases from lake shore to central lake. In the central lake facies, the second mode is dominant. A higher content of the second mode indicates its position more close to the central lake. (4) The grain size distribution of river sediments is the most complex. It consist of suspension, saltation and rolling modes. In most situations, the percentage of the saltation mode is larger than that of other modes. The percentage of suspension modes of river sediments is more than of sandy dunes. The grain size distribution of river sediments indicates dynamic strength of river currents. If the fourth mode is dominant, the dynamic forcing of river is weaker, such as in river floodplain. If the five or sixth mode is dominant, the water dynamic forcing of rivers is strong. (5) Sediments can be changed by later forcing in different degree to form some complicated deposition types. In the paper, the grain size distribution of aqueous sediments of windblown deposition, windblown sediments of aqueous deposition, weathering crust and slope materials are discussed and analyzed. 3. The grain size distribution characteristics of different sediments are concluded: (1) Modal difference: Usually there are suspended and saltation modes in the windblown deposition. The third mode is dominant in loess dust and the fifth mode is predominant in sandy dunes. There are suspended, saltation and rolling particles in aqueous sediments. In lacustrine sediments, the second and fourth mode are predominant for central lake facies or lake shore facies, respectively. In river sediments, the fourth, or fifth, or sixth mode is predominant. Suspended modes: the grain size of suspended particles of windblown depositions usually is less than 75μm. The content of suspended particles is lower or none in sandy dunes. However, suspended particles of aqueous sediments may reach 150μm. Difference in grain size of suspended modes represents difference between transitional mediums and the strength of dynamic forcing. Saltation modes: the median size of saltation mode of sandy dunes fluctuates less than that of river sediments. (2) Loess dust and lacustrine sediment: Their suspended particles are clearly different. There is an obvious pit between the second and the third modes in grain size distribution of lacustrine sediments. The phenomenon doesn’t occur in loess dust. In lacustrine sediments, the second mode can be a dominant mode, such as central lake facies, and contents of the second and the third modes change reversely. However, the percentage of the third mode is always the highest in loess dust. (3) Dune Sand and fluvial sand: In these two depositions, the saltation particles are dominant and the median sizes of their saltation modes overlay in distribution range. The fifth mode of dune sand fluctuates is sorted better than that of fluvial sand. (4) Lacustrine and fluvial sediments: In lacustrine sediments, there are 5-6 modes and suspended particles can be predominant. The second mode is dominant in central lake facies and the third mode is dominant in lake shore facies. Saltation or roll modes occurred in central lake facies may indicate strong precipitation events. In fluvial sediments, saltation particles (or rolling particles) usually dominant. 4. A estimation model of lake depth is firstly established by using contents of the second, the third and the fourth modes. 5. The paleoenvironmental history of the eastern part of SongLiao basin is also discussed by analyzing the grain size distribution of Yushu loess-like sediments in Jilin. It was found that there is a tectonic movement before 40ka B.P. in SongLiao basin. After the movement, loess dust deposited in Yushu area as keerqin desert developed. In recent 2000 years, the climate became drier and more deserts activated in the eastern part of Song-Liao basin.

Impact of cathode evaporation on a free-burning arc

A free-burning, high-intensity argon arc at atmospheric pressure was modelled during the evaporation of copper from the cathode. The effect of cathode evaporation on the temperature, mass flow, current flow and Cu concentration was studied for the entire plasma region. The copper evaporates from the tip of the cathode with an evaporation rate of 1 mg s-1. The copper vapour in the cathode region has a velocity of 210 m s-1 with a mass concentration of above 90% within 0.5 mm from the arc axis. The vapour passes from the cathode toward the anode with a slight diffusion in the argon plasma. Higher temperatures and current densities were calculated in the core of the arc caused by the cathode evaporation.

先进高重频激光处理对镀铬层结合特性的影响

采用特殊声学调制的高重频激光技术对钢基体强化处理，使基体表面形成按一定几何规律排列的微米量级和微坑，使得基体的表面形貌、微观组织、铬层与基体的结合等特征均发生了本质的变化。它有效地增加了基体的表面积，有利于电沉积初期铬原子沿基体原有晶格的外延生长；有效地改善了铬层与基体的结合效果，提高了铬层抵抗复杂应力破坏的能力。

柔性加工中高功率激光束空间变换研究

在国民经济中占有重要地位的汽车工业中，对于大型覆盖件模具的表面强化处理，最常见的是火焰淬火。火焰淬火对操作人员的要求高，可控性差，效果不理想，但是由于一直没有适合的方法，目前也只能继续使用。而激光表面强化技术结合柔性加工系统正是解决这类问题的新途径。传统的激光表面强化是采用把激光束离焦后进行扫描的方式，这种方法不能充分利用激光功率密度，而且往往要用转镜或振镜形成条形光斑来加快处理速度，这就需要复杂的机械结构，而且产生难以避免的重叠回火。我们提出一种新方法，利用二元光学元件来获得一种新型的周期光强分布，实现其在高功率激光系统中的应用，并设计成为集成到柔性加工系统中的组成部分，能够完成对大、中型模具表面的激光强化处理。本论文的工作主要是有关激光柔性加工系统中的光束传输及变换子系统，不仅包括理论设计、加工制作，同时还包括把该子系统有效的结合到整个系统中。本研究工作广泛涉及激光理论，光束变换和光纤传输，系统中的模块化集成应用技术，金属材料的特殊分布光强表面改性试验研究等等，是跨学科的交叉研究工作。在本论文中，重点是二元光学元件的设计方法的选择、计算机辅助设计的实现、二元光学元件的制作和在高功率激光传输中的应用，以及特殊光强分布应用于金属表面改性中的相关工作。通过把二元光学元件引入到高功率激光加工中，对出现的新现象给出一定的预测和分析，并获得了良好的强化结果，最终实现了系统的集成化，并具有实际生产所要求的可靠性和灵活性。本论文共分六章，主要包括两方面的内容。第一章为绪论，第六章为结论。第一方面内容在第二章到第四章中说明，是用于高功率激光应用中的二元光学元件的原理、设计和制作。第二方面的内容在第五章中，是关于应用前面设计制作的二元光学元件，在实际的金属材料表面处理中的实验研究，给出了相关试验结果。