Fabrication and spectral properties of Nd3+-doped yttrium lanthanum oxide transparent ceramics

Transparent 1 at% Nd3+:Y1.9La0.1O3 ceramics were fabricated with nanopowders prepared by carbonate coprecipitation method. The powder compacts were sintered in H-2 atmosphere at 1550 degrees C for 30 h. The Nd3+:Y1.9La0.1O3 ceramics display uniform grains of about 50 mu m and high transparency. The highest transmittance of the ceramics reaches 67%. The strongest absorption peak is in the wavelength of 820 nm with absorption cross section of 2.48 x 10(-20) cm(2). The absorption is still high at LD wavelength 806 nm with absorption cross section of 1.78 x 10(-20) cm(2) and broad full width at half maximum (FWHM) of about 6.3 nm. The strongest emission peak was centered at 1078 nm with large stimulated emission cross section of 9.63 x 10(-20) cm(2) and broad FWHM of about 7.8 nm. The broad absorption and emission bandwidth of Nd3+:y(1.9)La(0.1)O(3) transparent ceramics are favorable to achieve the miniaturized LD pumping apparatus and ultrashort modelocked pulse laser output, respectively. (c) 2007 Elsevier B.V. All rights reserved.

测量薄膜微粗糙度的总积分散射仪

介绍了一种检测光学薄膜表面总积分散射（TIS）分布的总积分散射仪。对仪器的基本结构、理论基础、测量原理以及系统性能等进行了阐述，提出了抑制系统噪音和提高测量精度的有效措施。利用该仪器对K9基底上的银（Ag）膜和氧化锆（ZrO2）薄膜进行了测量，并根据标量散射理论得到了表面均方根（RMS）粗糙度。利用光学轮廓仪和原子力显微镜（AFM）分别测量了上述Ag膜和ZrO2薄膜的表面均方根粗糙度，并与总积分散射仪所得的粗糙度进行了比较。结果表明，根据测量的薄膜表面总积分散射计算得到的表面均方根粗糙度与光学轮廓仪及原子

表面热透镜技术应用于薄膜微弱吸收测量的理论和实验

由薄膜表面光热形变简化理论和表面热透镜衍射理论导出表面热透镜信号表达式,从理论上证明了表面热透镜信号和薄膜吸收率的线性关系.应用表面热透镜技术研制了薄膜吸收测量仪,测量结果表明其吸收率测量灵敏度和精度均达10-6量级.

硫代硫酸钠及葡萄糖对蓝细菌Synechocystis sP.PCC6803脂及光合器组成的影响

本文通过对蓝细菌Synechocystis sp. PCC 6803在添加葡萄糖、Na2S203的BG-11培养基中的生长特性、脂类及脂肪酸组成、细胞低温荧光、色素组成进行分析测定，总结出如下规律： 当蓝细菌Synechocystis sp. PCC 6803在添加有葡萄糖的BG-11培养基中培养时细胞出现了一种新的糖脂（记为糖脂-x），在添加果糖、麦芽糖、乳糖等其它碳源的培养基中生长的细胞中也检测到糖脂-x糖脂-x的出现经推测是与活性氧相作用的产物，当在含糖的培养基中加入活性氧猝灭剂Na2S203时能有效地抑制糖脂-x的出现。糖脂一x的出现伴随着其它脂、尤其是双半乳糖甘油二酯(DGDG)的含量下降，这可能与细胞营养代谢类型的转变相适应。糖脂-x的出现使细胞适应异养生长条件，这时藻胆体(PBS)，光系统II(PSII)，光系统I(PSD降解，叶绿素消失。 糖脂-x经1H-NMR波谱术检测证实为甘油糖脂，经气质联谱分析其脂肪酸组成中含大量的枝链脂肪酸，12-甲基十四碳酸、12-甲基十五碳酸、12-甲基十六碳酸以及两种稀有的含氮脂肪酸。这些脂肪酸在添加高浓度葡萄糖的培养基中生长的．Synechocystis sp. PCC 6803中的单半乳糖甘油二酯(MGDG)也能检测到。ESI-MS以及P-SI-MS测定结果表明糖脂．x含一分子的脂酰基侧链以及两分子的己糖，半乳糖与葡萄糖。 对．Synechocystis sp. PCC 6803生长在不同浓度的葡萄糖与Na2S203培养基中脂类组成与脂肪酸组成进行比较，发现Na2S203能有效地增加膜脂中硫代异鼠李糖二酰基甘油(SQDG)和磷脂酰甘油(PG)的百分含量，培养基中同时添加葡萄糖时能抵消Na2S203的这一效应。此外，Na2S203能显著增加单半乳糖甘油二酯(MGDG)、双半乳糖甘油二酯(DGDG)中十六碳酸(C16:0)的百分含量，这一效应也能为葡萄糖恢复。Na2S203不能显著地改变SQDG中C16:0的百分含量，加入葡萄糖时能降低C16:0的百分含量。这些结果说明Na2S203可能充当一种还原剂使膜脂处于一种低的不饱和状态，同时加入葡萄糖时能降低Na2S203的还原力。此外，Na2S203还可作为SQDG合成中的硫供体。 用HPLC测定．Synechocystis sp. PCC 6803在添加不同浓度的Na2S203，葡萄糖的BG-11培养基中生长时的叶绿素与类胡萝卜素浓度，结果表明葡萄糖表现出对叶绿素与类胡萝卜素水平的抑制效应，Na2S203在低浓度时表现出对叶绿素与类胡萝卜素水平的促进效应，但在高浓度时表现出抑制效应。因此适当浓度的Na2S203的加入有利于维持蓝细菌在培养基中添加葡萄糖的生长条件下的低水平自由基，能使葡萄糖表现出促进细胞生长的特性。 通过测定Synechocystis sp. PCC 6803生长曲线中葡萄糖、Na2S203的浓度效应，结果表明葡萄糖在低浓度（例如5 mmoI.L-l）时表现出促进细胞的生长，在相对高的浓度表现出抑制细胞生长的效应。在培养基中同时加入Na2S203时可恢复葡萄糖对细胞的生长的促进效应。单独加入Na2S203表现出对细胞生长的抑制效应。这说明葡萄糖、Na2S203对细胞的生长存在着正的协同效应。

A new species of sisorid catfish genus Glyptothorax (Teleostei: Sisoridae) from Salween drainage of Yunnan, China

A new species of the genus Glyptothorax, Glyptothorax obliquimaculatus sp. nov. is described from the Xiaohei River, a tributary of the Nanting River, Salween drainage, in southwestern Yunnan province, China. This new species can be distinguished from its congeners by the following combination of characteristics: unculiferous ridges of the thoracic adhesive apparatus extending anteriorly onto the gular region; body with irregular dark blotches scattered along lateral surface (blotches mostly oblique); skin smooth on head and body; dorsal spine smooth without serrations on its posterior margin; lips smooth; posterior margin of pectoral spine with 7-8 serrations; dorsal-fin base 11.0-13.2% SL; pectoral-fin length 15.6-19.6% SL; depth of caudal peduncle 8.6-9.8% SL; head width 19.1-24.0% SL; nasal barbel length 23.3-33.3% HL.

COMPARISON OF MASTICATORY MORPHOLOGY BETWEEN RHINOPITHECUS-BIETI AND R-ROXELLANA

The masticatory apparatus for two endemic species of golden monkey in China, Rhinopithecus bieti and Rhinopithecus roxellana, were compared with those of macaques, Macaca and leaf monkeys, Presbytis. Multivariate analyses demonstrated that the two golden monkey species are distinct. Interspecies allometric analyses revealed that golden monkeys differ in their masticatory apparatus from both macaques and leaf monkeys. The prominent symphysial fusion, corpus, and sagittal condylar dimension of R. roxellana may produce efficient biting force on the incisal and posterior canine teeth, with the heavy reaction force barn on the temporomandibular joint. However, the well-developed bizygamatic width and mandibular height in R. bieti suggest that posterior canine function is similarly prominent in R. roxellana, while incisal function is not. (C) 1995 Wiley-Liss, Inc.

Reconsideration of Phylogenetic Relationships of the Subclass Peritrichia (Ciliophora, Oligohymenophorea) Based on Small Subunit Ribosomal RNA Gene Sequences, with the Establishment of a New Subclass Mobilia Kahl, 1933

Based on its characteristic oral apparatus, the ciliate subclass Peritrichia has long been recognized as a monophyletic assemblage composed of the orders Mobilida and Sessilida. Following the application of molecular methods, the monophyly of Peritrichia has recently been questioned. We investigated the phylogenetic relationships of the peritrichous ciliates based on four further complete small subunit ribosomal RNA sequences of mobilids, namely Urceolaria urechi, Trichodina meretricis, Trichodina sinonovaculae, and Trichodina ruditapicis. In all phylogenetic trees, the mobilids never clustered with the sessilids, but instead formed a monophyletic assemblage related to the peniculines. By contrast, the sessilids formed a sister clade with the hymenostomes at a terminal position within the Oligohymenophorea. We therefore formally separate the mobilids from the sessilids (Peritrichia sensu stricto) and establish a new subclass, Mobilia Kahl, 1933, which contains the order Mobilida Kahl, 1933. We argue that the oral apparatus in the mobilians and sessilid peritrichs is a homoplasy, probably due to convergent evolution driven by their similar life-styles and feeding strategies. Morphologically, the mobilians are distinguished from all other oligohymenophoreans by the presence of the adhesive disc, this character being a synapomorphy for the Mobilia.

EFFECT OF ELEVATED BICARBONATE CONCENTRATION ON GROWTH, CHLOROPHYLL A FLUORESCENCE AND ULTRA-STRUCTURE OF Microcystis aeruginosa (CYANOBACTERIUM)

The influence of bicarbonate (HCO3-) on Microcystis aeruginosa FACHB 905 was assessed in this study. Growth curves, chlorophyll a fluorescence and ultrastructure were measured at two HCO3- concentrations, 2.3 mM and 12.4 mM. A treatment of sodium chloride (NaCl) was also conducted alongside to establish the influence level of sodium. It was found that upon treatment with elevated HCO3- concentrations of 2.3 mM and 12.4 mM, cell densities were 13% and 27% (respectively) higher than controls. In photosynthetic performance, elevated HCO3- concentration initially stimulated Fv/Fm at the prophase of culture and then subsequently inhibited it. The inhibition of 2.3mM was higher than that of 12.4mM HCO3-. The maximum relative electron transport rate (ETRmax) exhibited inhibition at elevated HCO3- concentrations. DI0/CS was decreased at 2.3 mM and increased at 12.4mM. In the case of both treatments. ABS/CSI TR0/CS, ET0/CS, RC/CS0 and RC/CSm were decreased by elevated HCO3- concentrations, which indicated damage to photosynthetic apparati and an inactivation of a fraction of reaction centers. This point was also proven by ultrastructural photos. High HCO3--exposed cells lost the characteristic photosynthetic membrane arrangement compared with the control and high salinity treated samples. At the 2.3mM concentration of HCO3-. damage to photosynthetic apparati caused decreased photosynthetic activity. These findings suggested that elevated HCO3- concentration stimulated the growth and photosynthesis of M. aeruginosa FACHB 905 in a short time. Exposure to high HCO3- concentrations for a longer period of time will damage photosynthetic apparatus. In addition, the ultrastructure indicated that elevated HCO3--concentration lead to photosynthetic apparati damage. In our experiment, it was observed that the inhibition effect of 2.3mM HCO3- was higher than that of 12.4mM HCO3-. We hypothesized that M. aeruginosa FACHB 905 induced a protective mechanism under high concentrations of HCO3-.

High performance 1689-nm quantum well diode lasers

1689-nm diode lasers used in medical apparatus have been fabricated and characterized. The lasers had pnpn InP current confinement structure, and the active region consisted of 5 pairs of InGaAs quantum wells and InGaAsP barriers. Stripe width and cavity length of the laser were 1.8 and 300 pm, respectively. After being cavity coated. and transistor outline (TO) packaged, the lasers showed high performance in practice. The threshold current was about 13 +/- 4 mA, the operation current and the lasing spectrum were about 58 6 mA and 1689 +/- 6 nm at 6-mW output power, respectively. Moreover, the maximum output power of the lasers was above 20 mW.

Wear resistance of reaction sintered alumina/mullite composites

Alumina and alumina/mullite composites with mullite content of 0.96-8.72 vol.% were subjected to an abrasive wear test under loads of 0.1-2.0 N with a ball-on-disc apparatus. The wear rate and area fraction of pullout f(po) on the worn surfaces were measured. The wear resistances of the alumina/mullite composites were better by a factor of 1-2 than that of pure alumina. The main wear mechanism of alumina is fracture wear, and for alumina/mullite composites, fracture wear and plastic wear mechanisms work together. The influence of mechanical properties on wear resistance was estimated by Evans' method. It was found that the wear rate depends on f(po), and the primary reason for the better wear resistance of alumina/mullite composites is the reduction off, induced by fracture mode transition. (c) 2007 Elsevier B.V. All rights reserved.

Well-width dependence of in-plane optical anisotropy in (001) GaAs/AlGaAs quantum wells induced by in-plane uniaxial strain and interface asymmetry

The well-width dependence of in-plane optical anisotropy (IPOA) in (001) GaAs/AlxGa1-xAs quantum wells induced by in-plane uniaxial strain and interface asymmetry has been studied comprehensively. Theoretical calculations show that the IPOA induced by in-plane uniaxial strain and interface asymmetry exhibits much different well-width dependence. The strain-induced IPOA is inversely proportional to the energy spacing between heavy- and light-hole subbands, so it increases with the well width. However, the interface-related IPOA is mainly determined by the probability that the heavy- and light-holes appear at the interfaces, so it decreases with the well width. Reflectance difference spectroscopy has been carried out to measure the IPOA of (001) GaAs/AlxGa1-xAs quantum wells with different well widths. Strain- and interface-induced IPOA have been distinguished by using a stress apparatus, and good agreement with the theoretical prediction is obtained. The anisotropic interface potential parameters are also determined. In addition, the energy shift between the interface- and strain-induced 1H1E reflectance difference (RD) structures, and the deviation of the 1L1E RD signal away from the prediction of the calculation model have been discussed.

Preparation and characterization of Si sheets by renewed SSP technique

Silicon sheets from powder (SSP) ribbons have been prepared by modified SSP technique using electronic-grade (9N purity) silicon powder. The surface morphology, crystallographic quality, composition and electric properties of the SSP ribbons were investigated by surface profiler, X-ray diffraction (XRD), scanning electron microscopy (SEM), metallurgical microscope, Auger electron spectroscopy (AES) and four-point probe apparatus, respectively. The results show that the SSP ribbon made from electronic-grade silicon powder is a suitable candidate for the substrates of crystalline silicon thin film (CSiTF) solar cells, which could meet the primary requirements of CSiTF solar cell process on the substrates, including surface smoothness, crystallographic quality, purity and electric conductivity, etc. (C) 2004 Elsevier B.V. All rights reserved.

Strain-induced in-plane optical anisotropy in (001) GaAs/AlGaAs superlattice studied by reflectance difference spectroscopy

In-plane optical anisotropy (IPOA) in (001) GaAs/AlGaAs superlattice induced by uniaxial strain has been investigated by reflectance difference spectroscopy (RDS). Uniaxial strain on the order of 10(-4) was introduced by bending a strip sample with a stress apparatus. The IPOA of all interband transitions shows a linear dependence on strain. The birefringence and dichroism spectra induced by strain are obtained by RDS on the basis of a three-phase model, which is in good agreement with the reported results. (c) 2006 American Institute of Physics.

Effects of multistage coupling and disk flexibility on mistuned bladed disk dynamics

The effects ofdisk flexibility and multistage coupling on the dynamics of bladed disks with and without blade mistuning are investigated. Both free and forced responses are examined using finite element representations of example single and two-stage rotor models. The reported work demonstrates the importance of proper treatment of interstage (stage-to-stage) boundaries in order to yield adequate capture of disk-blade modal interaction in eigenfrequency veering regions. The modified disk-blade modal interactions resulting from interstage-coupling-induced changes in disk flexibility are found to have a significant impact on (a) tuned responses due to excitations passing through eigenfrequency veering regions, and (b) a design's sensitivity to blade mistuning. Hence, the findings in this paper suggest that multistage analyses may be required when excitations are expected to fall in or near eigenfrequency veering regions or when the sensitivity to blade mistuning is to be accounted for Conversely, the observed sensitivity to disk flexibility also indicates that the severity of unfavorable structural interblade coupling may be reduced significantly by redesigning the disk(s) and stage-to-stage connectivity. The relatively drastic effects of such modifications illustrated in this work indicate that the design modifications required to alleviate veering-related response problems may be less comprehensive than what might have been expected.

Experimental Investigation into the Production Behavior of Methane Hydrate in Porous Sediment with Hot Brine Stimulation

The gas production behavior from methane hydrate in porous sediment by injecting the brine with the salinity of 0−24 wt % and the temperature of −1 to 130 °C was investigated in a one-dimensional experimental apparatus. The results show that the gas production process consists of three periods: the free gas production, the hydrate dissociation, and the general gas reservoir production. The hydrate dissociation accompanies the temperature decrease with the injection of the brine (NaCl solution), and the dissociation duration is shortened with the increase of the salinity. With the injection of hot brine, instantaneous hydrate dissociation rate also increases with the increase of the salinity. However, while the NaCl concentration is beyond a certain value, the rate has no longer continued increasing. Thermal efficiency and energy ratio for the hydrate production can be enhanced by injecting hot brine, and the enhanced effectiveness is quite good with the injection of high salinity at lower temperature.