Characteristics of triangle and square InP/InGaAsP microlasers

Directional emission triangle and square InGaAsP/InP lasers have been fabricated by standard photolithography, inductively coupled plasma etching technique combined with wet chemical etching process. In this article, the characteristics of the microcavity lasers are presented. For an equilateral triangle microcavity laser with the side length of 30 mu m, we got the laser spectra fitted very well with the mode wavelength formulate LIP to the 8(th) transverse mode at room temperature. But the laser spectra are usually more complex than the formulae for the lasers, especially for the lasers with a smaller side length. For a square microcavity laser with side length of 20 mu m, we observed the mode competition between the Fabry-Perot (FP) modes and Whispering-Gallery (WG) modes at 200K. The output spectra below the threshold have the mode interval of FP modes with a large mode interval, and the laser spectra agree very well with the WG modes, which have mode interval less than the FP modes. The output spectra are dominated by the FP modes below the threshold, because the FP modes have a higher output coupling efficiency than the WG modes.

Novel photonic crystal structure GaN-based light-emitting diodes - art. no. 68410J

For enhancing the output efficiency of GaN light-emitting diode(LED), we calculated the band structure of photonic crystal(PhC), and designed and fabricated several novel GaN LEDs with photonic crystal on Indium-Tin-Oxide(ITO), which as p-type transparent contact of GaN LED. In this fabricating process, we developed conventional techniques in order that these methods can be easily applied to industrial volume-production. And we have done some preliminary experiments and obtained some results.

Investigation of vertical radiation loss for whispering-gallery modes in 3-D microresonators by FDTD simulation

The vertical radiation loss of three-dimensional (3-D) microresonators is investigated by 3-D finite-difference time-domain (FDTD) simulation. The simulation shows that the vertical radiation causes an important loss in the microresonators with weak waveguiding, and result in decrease of the quality factors (Q-factors) of whispering-gallery (WG) modes. Through the simulation, we find that TM-like modes have much weaker vertical radiation loss than TE-like modes. High Q-factor TM-like modes are observed in the 3-D microresonators with weak vertical waveguiding, but the Q-factors of TE-like modes decrease greatly.

Continuous-wave electrically injected InP/GaInAsP equilateral-triangle-resonator lasers

Equilateral-triangle-resonator (ETR) microlasers with an output waveguide connected to one of the vertices of the ETR are fabricated using standard photolithography and inductively-coupled-plasma etching techniques. Continuous-wave electrically injected 1550 nm ETR laser with side length ranged from 15 to 30 tm are realized at room temperature.

Influence of dispersive coupling coefficient in microring channel drop filters

Wide transmission dips are observed in the through spectra in microring and racetrack channel drop filters by two-dimensional finite-difference time-domain (FDTD) simulation. The transmission spectra, which reflect the coupling efficiency, are also calculated from the FDTD output as the pulse just travels one circle inside the resonator. The results indicate that the dips are caused by the dispersion of the coupling coefficient between the input waveguide and the resonator. In addition, a near-zero channel drop on resonance and a large channel drop off resonance are observed due to the near zero coupling coefficient and a large coupling coefficient, respectively. If the width of the input waveguide is different from that of the ring resonator, the oscillation of the coupling coefficient can be greatly suppressed.

Experimental Investigation on Propane Hydrate Dissociation by High Concentration Methanol and Ethylene Glycol Solution Injection

The dissociation behaviors of propane hydrate by high concentration alcohols inhibitors injection were investigated. Methanol (30.0, 60.1, 80.2, and 99.5 wt %) and ethylene glycol (30.0, 60.1, 69.8, 80.2, and 99.5 wt %) solution were injected, respectively, as alcohols inhibitors in 3.5 L transparent reactor. It is shown that the average dissociation rates of propane hydrate injecting methanol and ethylene glycol solution are 0.02059-0.04535 and 0.0302-0.0606 mol.min(-1).L-1, respectively. The average dissociation rates increase with the mass concentration increase of alcohols solution, and it is the biggest when 99.5 wt % ethylene glycol solution was injected. The presence of alcohols accelerates gas hydrate dissociation and reduces the total need of external energy to dissociate the hydrates. Density differences act as driving force, causing the acceleration effects of ethylene glycol on dissociation behaviors of propane hydrate are better than that of methanol with the same injecting flux and mass concentration.

Continuous-flow polymerase chain reaction microfluidics by using spiral capillary channel embedded on copper

This paper presents a novel method for performing polymerase chain reaction (PCR) amplification by using spiral channel fabricated on copper where a transparent polytetrafluoroethylene ( PTFE) capillary tube was embedded. The channel with 25 PCR cycles was gradually developed in a spiral manner from inner to outer. The durations of PCR mixture at the denaturation, annealing and extension zones were gradually lengthened at a given flow rate, which may benefit continuous-flow PCR amplification as the synthesis ability of the Taq polymerase enzyme usually weakens with PCR time. Successful continuous-flow amplification of DNA fragments has been demonstrated. The PCR products of 249, 500 and 982 bp fragments could be obviously observed when the flow rates of PCR mixture were 7.5, 7.5 and 3.0 mm s(-1), respectively, and the required amplification times were about 25, 25, and 62 min, respectively. Besides, the successful segmented-flow PCR of three samples ( 249, 500 and 982 bp) has also been reported, which demonstrates the present continuous-flow PCR microfluidics can be developed for high-throughput genetic analysis.

Study on the kinetics of hydrate formation in a bubble column

Gas hydrate formation experiments were performed using methane in the presence of tetrahydrofuran (THF) in aqueous solution in a transparent bubble column in which a single pipe or a sintered plate was used to produce bubbles. The mole fraction of THF in aqueous solution was fixed at 6%. The hydrate formation kinetic behaviors on the surface of the rising bubble, the mechanical stability of hydrate shell formed on the surface of the bubble, the interactions among the bubbles with hydrate shell were observed and investigated morphologically. The rise velocities of individual bubbles with hydrate shells of different thickness and the consumption rates of methane gas were measured. A kinetic model was developed to correlate the experimentally measured gas consumption rate data. It was found that the hydrate formation rate on the surface of the moving bubble was high, but the formed hydrate shell was not very easy to be broken up. The bubbles with hydrate shells tended to agglomerate rather than merge into bigger bubble. This kind of characteristic of hydrate shell hindered the further formation of hydrate and led to the lower consumption rate of methane. The consumption rate of methane was found to increase with the decrease of temperature or increase of pressure. The increase of gas flux led to a linear increase in consumption rate of methane. It was demonstrated that the developed kinetic model could be used to correlate the consumption rate satisfyingly.

Large and negative lateral displacement in an active dielectric slab configuration

We investigate the large negative lateral displacements of TE polarized light beams reflected from or transmitted through an active slab surrounded by transparent medium. The large negative displacements can be achieved when the incidence angle of the beam is less than but close to the critical angle for total reflection. It is also shown that both the reflectivity and transmissivity of the beam that correspond to the large negative displacements can be enhanced by active medium. These phenomena may lead to convenient measurements and interesting applications in optical devices. (c) 2006 Elsevier B.V. All rights reserved.

Kinetics of picosecond laser pulse induced charge separation and proton transfer in bacteriorhodopsin

Bacteriorhodopsin (BR) films oriented by an electrophoretic method are deposited on a transparent conductive ITO glass. A counterelectrode of copper and gelose gel is used to compose a sandwich-type photodetector with the structure of ITO/BR film/gelose gel/Cu. A single 30-ps laser pulse and a mode-locked pulse train are respectively used to excite the BR photodetector. The ultrafast failing edge and the bipolar response signal are measured by the digital oscilloscope under seven different time ranges. Marquardt nonlinear least squares fitting is used to fit all the experimental data and a good fitting equation is found to describe the kinetic process of the photoelectric signal. Data fitting resolves six exponential components that can be assigned to a seven-step BR photocycle model: BR-->K-->KL-->L-->M-->N-->O-->BR. Comparing tests of the BR photodetector with a 100-ps Si PIN photodiode demonstrates that this type of BIR photocletector has at least 100-ps response time and can also serve as a fast photoelectric switch. (C) 2003 Society of Photo-Optical Instrumentation Engineers.

PHOTOEMISSION-STUDY ON THE SNO2/P A-SICX-H INTERFACE

Ultraviolet and X-ray photoemission spectroscopies (UPS and XPS) have been employed to SnO2 and its interface with P-type a-SiCx:H. The HeI valence band spectra of SnO2 show that the valence band maximum (VBM) shifts from 4.7 eV to 3.6 eV below the Fermi level (E(F)), and the valence band tail (VBT) extends up to the E(F), as a consequence of H-plasma treatments. The work function difference between SnO2 and P a-SiCx:H is found to decrease from 0.98 eV to 0.15 eV, owing to the increase of the work function of the treated SnO2. The reduction of SnO2 to metallic Sn is also observed by XPS profiling, and it is found that this leads to a wider interfacial region between the treated SnO2 and the successive growth of P a-SiCx:H.

The growth of ZnO on bcc-In2O3 buffer layers and the valence band offset determined by X-ray photoemission spectroscopy

This work was supported by the 863 High Technology R&D Program of China (Grant Nos. 2007AA03Z402 and 2007AA03Z451), the Special Funds for Major State Basic Research Project (973 program) of China (Grant No. 2006CB604907), and the National Science Foundation of China (Grant Nos. 60506002 and 60776015). The authors express their appreciation to Dr. Tieying Yang and Prof. Huanhua Wang (Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences) for XRD measurements and helpful discussions.

Metallic glass nanofilms

In this paper, we report for the first time the spontaneous formation of Zr-based metallic glass nanofilms by developed dynamic forced-shear-rupture technique of hat-shaped specimens. The obtained nanofilms have about 100 nm thickness and other two geometrical dimensions can reach micrometer scales. Their glassy nature and structural stability were solidly identified. It was found that electrons with the wavelength of less than 0.165 Å could make the metallic glass nanofilms transparent. Furthermore, it is clearly shown that shearbanding instability still afflicts such 100-nm-thick metallic glass nanofilms.

己酸乙酯酯化真菌筛选及发酵条件研究

本文主要研究了具有己酸乙酯酯化活性的真菌菌株的筛选和发酵条件优化。从大曲和糟醅样品中分离纯化获得79株产生透明圈的丝状真菌，菌落形态初步识别结果显示分离菌株包括红曲霉属、根霉属及曲霉属等菌株。其中菌株EM-56酯化酶活力最强，发酵获得的粗酶制剂酶活为172.36 u。根据显微形态、菌落形态及生理生化特征，初步鉴定该菌株为曲霉科红曲霉属紫色红曲霉（Monascus purpureus）。 在此基础上重点研究了菌株EM-56在不同培养基成分及不同培养条件下的产酶情况，确定了最佳培养基和培养条件。通过单因素实验确定在基础培养基中添加最佳碳源为葡萄糖，最佳氮源为蛋白胨。正交优化实验结果确定了最佳培养基组成：以麸皮为基础培养基，添加葡萄糖 2%，蛋白胨 0.3 %，KH2PO4.3H2O 0.05 %，MgSO4.7H2O 0.06 %。菌株EM-56在上述培养基中的最佳发酵条件为：初始pH 5.5，发酵温度为35°C，发酵时间7d，种龄48h，接种量8%，装瓶量50g / 瓶（500mL）。在最佳培养基和发酵条件下，菌株EM-56发酵获得的粗酶制剂酶活达到241.56 u，比优化前提高了40.15%。 In this paper, the research focuses on the selection of fungus with esterifying activity and optimization of fermentation conditions. We isolated 79 strains which had transparent zones from Daqu and fermented grains. The isolated strains contained Monascus、Rhizopus and Aspergillus through primary morphology analysis. The strain of EM-56 which produces strongest esterase was selected. The enzyme activity reached 172.36u. According to related literature, EM-56 was identified as Monascus purpureus through morphology analysis and biochemical determination. We also studied the effects of different medium and fermentation conditions on the esterase production of strain EM-56. The optimal medium and fermentation conditions were determined. Single factor experiment result shows that the optimal carbon source added is glucose and the optimal nitrogen source added is peptone. The optimal fermentation medium determined by orthogonal optimization test is as follows: wheat bran as substrate, glucose 2%, peptone 0.3%, KH2PO4.3H2O 0.05%，MgSO4.7H2O 0.06%. The optimal fermentation conditions are: initial pH 5.5, cultural temperature 35°C, cultural time 7d, seed age 48h, inoculation 8%, medium mass 50g / flask（500mL）. The esterse activity of EM-56 cultivated in the optimal medium and fermentation conditions reached 241.56u and increased by 40.15% compared with the original activity.

改进的SILAR法制备ZnO薄膜及其表征

A modified solution method, successive ionic layer adsorption and reaction(SILAR), was applied to prepare transparent zinc oxide(ZnO) film on glass substrate at (125±5) ℃ in mixed ion precursor solution. The surface morphology and crystallizations of films were analyzed by field emission scanning microscopy(FESEM) and X-ray diffraction(XRD), respectively. The optical properties of the films were studied by ultraviolet visible(UV-Vis)spectroscopy. The results show that the obtained samples are polycrystallin...中文文摘：采用一种改进的液相成膜技术——连续离子层吸附与反应(SILAR)法,用锌氨络离子[Zn(NH3)4]2+溶液作为独立的前驱体溶液,以载玻片为衬底,在(125±5)℃的温度下沉积出致密、透明的ZnO薄膜。分别用冷场发射型扫描电镜(FESEM)和X射线衍射(XRD)分析了薄膜样品的表面形貌和结晶状态,用紫外-可见分光光度计(UV-Vis spectroscopy)研究了薄膜样品的发光性能。结果表明:获得样品为六角纤锌矿结构的多晶薄膜材料沿[002]方向择优生长;样品表面均匀、致密,厚度约为550nm;在可见光波段具有高的透射率(>80%)。