PREPARATION, STRUCTURE AND INFLUENCE OF VALENCE STATE ON LASR2-XCAXV3O9+/-Y

New compounds LaSr2-xCa-(x)V3O9+/-y (x = 0.0, 0.67, 1.0, 1.33 and 2.0) have been synthesized with a simple new method X ray powder diffraction results indicate that they are single compound. Their lattice constants are calculated. The structure of LaSr2-xCa(x)V39+/-y changed from cubic to orthorhombic and back to cubic with the increase of calcium content. The results of weight gain in TG and XPS curves show that vanadium with lower valent state is oxidized to higher valent state at higher temperature. The oxygen content of new compounds are calculated from the weight gain. It is shown that V3+ and V4+ may coexist in LaSr2-xCa(x)V3O9+/-y. These compounds show that low resistivity.

The preparation and bioactivity research of agaro-oligosaccharides

Agaro-oligosaccharides were hydrolytically obtained from agar using hydrochloric acid, citric acid, and cationic exchange resin (solid acid). The FT-IR and NMR data showed that the hydrolysate has the structure of agaro-oligomers. Orthogonal matrix method was applied to optimize the preparation conditions based on alpha-naphthylamine end-labeled HPLC analysis method. The optimal way for oligosaccharides with different degree of polymerization (DP) was achieved by using solid acid degradation, which could give high yield and avoid solution neutralization process. Agaro-oligosaccharides with high purity were consequently obtained by activated carbon column isolation. Furthermore, the antioxidant and alpha-glucosidase inhibitory activity of three fractions were also investigated. The result indicated that 8% ethanol-eluted fraction showed highest activity against alpha-glucosidase with IC50 of 8.84 mg/mL, while 25% ethanol-eluted fraction possessed excellent antioxidant ability.

Preparation of chloroplasts from brown algae

Thalli from a brown alga Undaria pinnatifida were soaked by CaCl2 solution with different concentration and time at 4 degreesC, the effect of CaCl2 solution on efficiency and influorescence emission spectra of chloroplasts were examined. The results show that the efficiency of collected chloroplasts is increased markedly after soaking in CaCl2 solution. According to the results of collected efficiency and characteristic of influorescence emission spectra at room temperature of chloroplasts, it was suggested that soaking in the 0.2 mol/L CaCl2 solution for 10 min is optimum. Under this condition, the efficiency of collected chloroplasts is as 5 fold as control group, and the characteristics of chloroplasts obtained by CaCl2 soaking are similar to that of traditional method.

Preparation of porous chitosan/agarose microsphere and its R-phycoerythrin release properties

The chitosan microspheres (CS-CL) were prepared by suspension crosslinking method and used as carriers of R-phycoerythrin (R-PE). In this study, R-PE was loaded in the microspheres and released in vitro. The effects of pH value, temperature, ionic strength, and R-PE concentration on loading efficiency and release behavior were discussed. A novel microsphere that contained agarose (CS-AR MP) was prepared and the basic loading and releasing behavior for R-PE of this kind of new micro-spheres were also investigated. The results showed that all these chitosan microspheres have the ability to control-release R-PE. The addition of agarose may somewhat accelerate the release rate of R-PE from microspheres and reduce the capacity of adsorption for R-PE. (c) 2006 Wiley Periodicals, Inc.

Analysis on suspended sediment deposition rate for muddy coast of reclaimed land

A new expression for calculating suspended fine-sediment deposition rate is developed based on theoretic analysis and experiments. The resulting equation is applied to simulation of fine sediment deposition in the reclaimed land in the Hangzhou Bay, China. The hydrodynamic environment in this area is solved by use of a long wave model, which gives the 2D-velocity field and considers bathymetric changes due to fine sediment deposition. The expression is proved convenient to use in engineering practice, and the predicted deposition rate agrees with the annual data available from field measurements from the first year to the third year after the construction of the long groin as a reclaiming method.

The preparation and antioxidant activity of glucosamine sulfate

Glucosamine sulfate was prepared from glucosamine hydrochloride that was produced by acidic hydrolysis of chitin by ion-exchange method. Optical rotation and elemental analysis characterized the degree of its purity. In addition, the antioxidant potency of chitosan derivative-glucosamine sulfate was investigated in various established in vitro systems, such as superoxide (O (2) (-) )/hydroxyl (center dot OH) radicals scavenging, reducing power, iron ion chelating. The following results are obtained: first, glucosamine sulfate had pronounced scavenging effect on superoxide radical. For example the O (2) (-) scavenging activity of glucosamine sulfate was 92.11% at 0.8 mg/mL. Second, the center dot OH scavenging activity of glucosamine sulfate was also strong, and was about 50% at 3.2 mg/mL. Third, the reducing power of glucosamine sulfate was more pronounced. The reducing power of glucosamine sulfate was 0.643 at 0.75 mg/mL. However, its potency for ferrous ion chelating was weak. Furthermore, except for ferrous ion chelating potency, the scavenging rate of radical and reducing power of glucosamine sulfate were concentration-dependent and increased with their increasing concentrations, but its ferrous ion chelating potency decreased with the increasing concentration. The multiple antioxidant activities of glucosamine sulfate were evidents of reducing power and superoxide/hydroxyl radicals scavenging ability. These in vitro results suggest the possibility that glucosamine sulfate could be used effectively as an ingredient in health or functional food, to alleviate oxidative stress.

Preparation of Dendritic Copper Nanostructures and Their Characterization for Electroreduction

Dendritic copper nanostructures of different morphologies were synthesized by a surfactant-free electrochemical method. Single crystal nature of the nanostructures was revealed from their X-ray diffraction and electron diffraction patterns. Mechanism of dendrite formation was discussed from thermodynamic aspects using the concept of supersaturation. Supersaturation of the copper metal reduced on the surface of the electrode was the crucial factor for the generation of different morphologies. Effects of applied potential, temperature, and the solution concentration on the supersaturation were studied. The NO3- and H2O2 electroreduction ability of the dendritic materials was tested. Use of copper dendrite-modified electrode as NO3- sensor was demonstrated.

Preparation and characterization of palladium-based composite membranes by electroless plating and magnetron sputtering

Pd and Pd-Ag (24 wt.%) alloy composite membrane were prepared by electroless plating and magnetron sputtering, respectively. The membranes were characterized by scanning electron microscopy (SEM) and H-2 permeation measurement. Commercial microfiltration ceramic membrane were coated with gamma-Al2O3-based layer by the sol-gel method and used as substrate of Pd and Pd-Ag alloy film. Both the as-prepared membranes were shown: to be He gas-tight at room temperature with a thickness of <1 mu m. Permeation results showed that H-2 permeation through these composite membranes is mainly dominated by the surface chemistry of H-2 on or/and in the membranes. The membranes exhibited a high permeation rate of H-2 and a H-2/N-2 permselectivity of higher than 60 in the optimized operation conditions. (C) 2000 Elsevier Science B.V. All rights reserved.

A novel method to synthesize amorphous silica-alumina materials with mesoporous distribution without using templates and pore-regulating agents

In this study, a novel sol-gel method is used to synthesize amorphous silica-alumina materials with a narrow mesoporous distribution and various Si/Al molar ratios without using any templates and pore-regulating agents. During the preparation procedure, only inexpensive inorganic salts were used as raw materials, instead of expensive and harmful alkoxides. The precursor sol was dried at room temperature in a vacuum box kept at 60 mmHg until it began to form the gel. The results of a nitrogen sorption experiment indicate that the synthesized materials with different Si/Al molar ratios have similar mesoporous distributions (within 2-12 nm). Moreover, it was found that the material's pore size distribution remains at a similar value during the heat treatment from room temperature to 550 degreesC. On the basis of the nitrogen sorption, TEM, and AFM characterization results, a formation mechanism of mesopores which accounts for the experimental data is also suggested. This suggested mechanism involves rearrangement of the primary particles during the drying process to form the precursors of the similarly sized mesopores. The synthesized materials were characterized by XRD, thermal analysis (TG/DTA), Al-27 and Si-29 MAS NMR spectroscopy, SEM, TEM, and AFM. The results of Al-27 and 29Si MAS NMR indicate that the distribution of silicon and aluminum in the synthesized materials is more uniform and homogeneous than that in the mixed oxides prepared via the traditional sol-gel method even at high alumina contents. The type and density of the acid sites were studied using pyridine adsorption-desorption FTIR spectroscopy. It was shown that the acidity of the synthesized materials is higher than that of the silica-alumina materials prepared by conventional methods.

An in-situ modified sol-gel process for monolith catalyst preparation used in the partial oxidation of methane

An in-situ modified sol-gel method for the preparation of a Ni-based monolith-supported catalyst is reported. With the presence of a proper amount of plasticizer and binder, and at an optimized pH value, the stable boehmite sol was modified with metal ions (Ni, Li, La) successfully without distinct growth of the particle size. Monolith-supported Ni-based/gamma-Al2O3 catalysts were obtained using the modified sol as the coating medium with several cycles of dip-coating and calcination. Combined BET, SEM-EDS, XRD and H-2-TPR investigations demonstrated that the derived monolith catalysts had a high specific surface area, a relatively homogeneous surface composition, and a high extent of interaction between the active component and the support. These catalysts showed relatively stable catalytic activities for partial oxidation of methane (POM) to syngas under atmospheric pressure. The monolith catalysts prepared by this sol-gel method also demonstrated an improved resistance to sintering and loss of the active component during the reaction process.

Preparation and characterization of Pd-Ag alloy composite membrane with magnetron sputtering

A Pd-Ag (24 wt%) alloy composite membrane was prepared by the magnetron sputtering. A gamma-Al2O3 membrane was synthesized by the sol-gel method and used as substrate of the Pd-Ag alloy film. The process parameters of the magnetron sputtering were optimized as a function of the compactness of the Pd-Ag alloy film. The best membrane with a thickness of 1 mu m was produced with a sputtering pressure of 2.7 Pa and a substrate temperature of 400 degrees C. The membrane had an H-2/N-2 permselectivity of 51.5-1000 and an H-2 permeation rate of 0.036-1.17 x 10(-5)cm(3)/cm(2).s. Pa, depending on operating conditions.

Preparation and characterization of multi-walled carbon nanotubes supported PtRu catalysts for proton exchange membrane fuel cells

A series of PtRu nanocomposites supported on H2O2-oxidized multi-walled carbon nanotubes (MWCNTs) were synthesized via two chemical reduction methods - one used aqueous formaldehyde (HCHO method) and the other used ethylene glycol (EG method) as the reducing agents. The effects of the solvents (water and ethylene glycol) and the surface composition of the MWCNTs on the deposition and the dispersion of the metal particles were investigated using N-2 adsorption. TEM. ICP-AES. FTIR and TPD. The wetting heats of the MWCNTs in corresponding solvents were also measured. The characterizations suggest that combination of the surface chemistry of the MWCNTs with the solvents decides the deposition and the dispersion of the metal nanoparticles. These nanocomposites were evaluated as proton exchange membrane fuel cell anode catalyts for oxidation of 50 ppm CO contaminated hydrogen and compared with a commercial PtRu/C catalyst. The data reveal superior performances for the nanocomposites prepared by the EG method to those by the HCHO method and even to that for tile Commercial analogue. Structure performance relationship of the nanocomposites was also studied. (C) 2005 Elsevier Ltd. All rights reserved.

Improved procedure for preparation of covalently bonded cellulose tris-phenylcarbamate chiral stationary phases

The classical method for preparation of covalently boned cellulose derivative chiral stationary phases (CSP) with diisocyanate as spacer was improved. Diisocyanate was firstly allowed to react with 3-aminopropyltriethoxysilane, and the resulting product was then applied as the spacer reagent to immobilize cellulose derivatives onto silica gel. Influences of the amount and the length of the spacer on the optical resolution ability of the CSP were investigated. Comparing improved procedure to classical diisocyanate method, the cross-linking between the glucose units of the cellulose derivatives was avoided to the most extent. With the improved procedure, regio-nonselective ways could be adopted to prepare covalently bonded CSP, which showed an advantage for the rapid preparation.