Forebody Compressibility Research of Hypersonic Vehicle

Three kinds of forebody model of hypersonic vehicles were studied with numerical simulation method. It shows that the two- order compressive ramp model is the best selection among the three for its good evaluative parameters value at the cowl of the inlet . This model can provide higher value of flux coefficient and total pressure recovery coefficient and lower average Mach number compared with those of the other two models . Simultaneously different compressive angles may have different effects . The configuration which the firstorder of compressive angle is 4°and the second 5°is the optimum combination. Furthermore factors such as attack angle were concerned. Better result may be obtained with a range of attack angles . Based on the work above the integrated design for forebodyPinlet of a hypersonic vehicle was performed. The numerical result shows that this integrated model provides good flow field quality for inlet and engine work.

一种任务优先级的综合设计方法

提出了一种基于优先级表设计的调度算法.将任务的相对截止期和空闲时间这两个特征参数结合起来,综合设计任务的优先级表,使得截止期越早或空闲时间越短,任务的优先级越高,而且任务的优先级由相对截止期和空闲时间惟一确定.对于任意一个任务,可通过对设计的优先级表进行二元多点插值获得相应任务的惟一优先级.与传统的EDF和LSF算法进行仿真比较,仿真结果表明,通过优先级表设计方法来确定任务的优先级,提高了任务调度的成功率,降低了任务截止期的错失率.该方法可应用于实时系统中实时任务的动态调度中.

钢丝绳结构及工艺集成设计系统

针对钢丝绳实际生产需要,提出基于钢丝绳结构理论设计基础的结构与工艺集成设计系统框架,建立钢丝绳结构设计、性能分析及间隙计算的理论模型,并利用相关数据进行理论值与实际值分析,完成钢丝绳性能参数的敏感性分析模型和理论修正模型,为钢丝绳结构设计与工艺设计的并行处理提供了理论上的指导,最终实现钢丝绳的智能设计与制造

Design of two-dimensional photonic crystal edge emitting laser for photonic integrated circuits

An edge emitting laser based on two-dimensional photonic crystal slabs is proposed. The device consists of a square lattice microcavity, which is composed of two structures with the same period but different radius of air-holes, and a waveguide. In the cavity, laser resonance in the inner structure benelits from not only the anomalous dispersion characteristic of the first band-edge at the M point in the first Brillouin-zone but also zero photon states in the outer structure. A line defect waveguide is introduced in the outer structure for extracting photons from the inner cavity. Three-dimensional finite-difference time-domain simulations apparently show the in-plane laser output from the waveguide. The microcavity has an effective mode volume of about 3.2(lambda/eta(slab))(3) for oscillation -mode and the quality factor of the device including line defect waveguide is estimated to be as high as 1300.

Mode analysis of photonic crystal polarization beam splitter and its application in integrated circuits design - art. no. 698437

In this work, the guided modes of a photonic crystal polarization beam splitter (PC-PBS) are studied. We demonstrate that the transmission of a low-loss photonic crystal 120 degrees waveguide bend integrated with the PBS will be influenced if the PBS is multi-moded. We propose a single-moded PC-PBS structure by introducing deformed structures, and it shows twice the enhancement of the transmission. This device with remarkable improvement of performance is promising in the use of photonic crystal integrated circuits design.

On the performance analysis and design of a novel shared-layer integrated devices using RCE-p-i-n-PD/SHBT - art. no. 67820J

We have explored the shared-layer integration fabrication of an resonant-cavity-enhanced p-i-n photodector (RCE- p-i-n-PD) and a single heterojunction bipolar transistor (SHBT) with the same epitaxy grown layer structure. MOCVD growth of the different layer structure for the GaAs based RCE- p-i-n-PD/SHBT require compromises to obtain the best performance of the integrated devices. The SHBT is proposed with super-lattice in the collector, and the structure of the base and the collector of the SHBT is used for the RCE. Up to now, the DC characteristics of the integrated device have been obtained.

Design and performance of monolithic integrated electro-absorption modulated distributed feedback laser - art. no. 67820Y

High performance InGaAsP/InGaAsP strained compensated multiple-quantum-well (MQW) electroabsorption modulators (EAM) monolithically integrated with a DFB laser diode have been designed and realized by ultra low metal-organic vapor phase epitaxy (MOVPE) based on a novel butt joint scheme. The optimization thickness of upper SCH layer for DFB and EAM was obtained of the proposed MQW structure of the EAM through numerical simulation and experiment. The device containing 250(mu m) DFB and 170(mu m) EAM shows good material quality and exhibits a threshold current of 17mA, an extinction ratio of higher than 30 dB and a very high modulation efficiency (12dB/V) from 0V to 1V. By adopting a high-mesa ridge waveguide and buried polyimide, the capacitance of the modulator is reduced to about 0.30 pF corresponding to a 3dB bandwidth more than 20GHz.

Design and operation of integrated pilot-scale dimethyl ether synthesis system via pyrolysis/gasification of corncob

The integrated pilot-scale dimethyl ether (DME) synthesis system from corncob was demonstrated for modernizing utilization of biomass residues. The raw bio-syngas was obtained by the pyrolyzer/gasifier at the yield rate of 40-45 Nm(3)/h. The content of tar in the raw bio-syngas was decreased to less than 20 mg/Nm(3) by high temperature gasification of the pyrolysates under O-2-rich air. More than 70% CO2 in the raw bio-syngas was removed by pressure-swing adsorption unit (PSA). The bio-syngas (H-2/CO approximate to 1) was catalytically converted to DME in the fixed-bed tubular reactor directly over Cu/Zn/Al/HZSM-5 catalysts. CO conversion and space-time yield of DME were in the range of 82.0-73.6% and 124.3-203.8 kg/m(cat)(3)/h, respectively, with a similar DME selectivity when gas hourly space velocity (GHSV, volumetric flow rate of syngas at STP divided by the volume of catalyst) increased from 650 h(-1) to 1500 h(-1) at 260 degrees C and 4.3 MPa. And the selectivity to methanol and C-2(+) products was less than 0.65% under typical synthesis condition. The thermal energy conversion efficiency was ca. 32.0% and about 16.4% carbon in dried corncob was essentially converted to DME with the production cost of ca. (sic) 3737/ton DME. Cu (111) was assumed to be the active phase for DME synthesis, confirmed by X-ray diffraction (XRD) characterization.

Design and Operation of A 5.5 MWe Biomass Integrated Gasification Combined Cycle Demonstration Plant

The design and operation of a 5.5 MWe biomass integrated gasification combined cycle (IGCC) demonstration plant, which is located in Xinghua, Jiangsu Province of China, are introduced. It is the largest complete biomass gasification power plant that uses rice husk and other agricultural wastes as fuel in Asia. It mainly consists of a 20 MWt atmospheric circulating fluidized-bed gasifier, a gas-purifying system, 10 sets of 450 kW(e) gas engines, a waste heat boiler, a 1.5 MWe steam turbine, a wastewater treatment system, etc. The demonstration plant has been operating since the end of 2005, and its overall efficiency reaches 26-28%. Its capital cost is less than 1200 USD/kW, and its running cost is about 0.079 USD/kWh based on the biomass price of 35.7 USD/ton. There is a 20% increment on capital cost and 35% decrease on the fuel consumption compared to that of a 1 MW system without a combined cycle. Because only part of the project has been performed, many of the tests still remain and, accordingly, must be reported at a later opportunity.

Materials selection in mechanical design for microsensors and microactuators

Microsensors and microactuators are vital organs of microelectromechanical systems (MEMS), forming the interfaces between controller and environment. They are usually used for devices ranging in size at sub-millimeter or micrometer level, transforming energy between two or more domains. Presently, most of the materials used in MEMS devices belong to the silicon material system, which is the basis of the integrated circuit industry. However, new techniques are being explored and developed, and the opportunities for MEMS materials selection are getting broader. The present paper tries to apply 'performance index' to select the material best suited to a given application, in the early stage of MEMS design. The selection is based on matching performance characteristics to the requirements. A series of performance indices are given to allow a wide range comparison of materials for several typical sensing and actuating structures, and a rapid identification of candidates for a given task. (C) 2002 Elsevier Science Ltd. All rights reserved.

Effects of nutrients on the substrate biofilms in the integrated vertical-flow constructed wetland

A L9 orthogonal array design involving 3 factors (C6H12O6, KNO3 and NaH2PO4) and 3 levels for each (C6H12O6: 0.2, 0.4 or 0.8 g/L; KNO3: 0.4, 0.8 or 1.6 g/L, NaH2PO4: 0.05, 0.1 or 0.2 g/L), was used to study the effects of nutrients on dehydrogenase activity and polysaccharide content of substrate biofilms in the integrated vertical-flow constructed wetland (IVCW). Results showed that C6H12O6 and KNO3 were the main factors for dehydrogenase activity and polysaccharide content of biofilms, respectively. The combinations of three nutrients at different concentrations had different effects on dehydrogenase activity and polysaccharide content of biofilms. The optimal combination for dehydrogenase activity was obtained by locating the concentrations Of C6H12O6, KNO3 and NaH2PO4 at 0.2, 0.8 and 0.05 g, and the optimal combination for polysaccharide content was obtained by locating the concentrations Of C6H12O6, KNO3 and NaH2PO4 at 0.2, 0.4 and 0.2 g/L, respectively. The corresponding maximum activity and polysaccharide content were 5.40 mu g TF/g substrate/12 h and 3454.6 mu g/g substrate, respectively. These results would provide the laboratory foundation for optimizing the purification function of the wetland systems.

Design of a compact polarizing beam splitter based on a photonic crystal ring resonator with a triangular lattice

We propose and simulate a new kind of compact polarizing beam splitter (PBS) based on a photonic crystal ring resonator (PCRR) with complete photonic bandgaps. The two polarized states are separated far enough by resonant and nonresonant coupling between the waveguide modes and the microring modes. Some defect holes are utilized to control the beam propagation. The simulated results obtained by the finite-difference time-domain method show that high transmission (over 95%) is obtained and the polarization separation is realized with a length as short as 3.1 mu m. The design of the proposed PBS can be flexible, thanks to the advantages of PCRRs.

Design of novel polarization beam splitter in two-dimensional photonic crystal

We present the design and the simulation of an ultracompact high efficiency polarization beam splitter (PBS) based on the properties of the light waves propagating in straight waveguide and composite structure photonic crystal. The splitting properties of the PBS are numerically simulated and analyzed by using the plane wave expansion (PWE) method and finite difference time domain (FDTD) method. The PBS consists of three parts, namely, input waveguide, beam structure and output waveguide. It is shown that a high efficiency and a large separating angle for TE mode and TM mode can be achieved. Owing to these excellent features, including small size and high rate, the PBS makes a promising candidate in the future photonic integrated circuits.

Design, fabrication and characterization of a high-performance microring resonator in silicon-on-insulator

A high-performance microring resonator in a silicon-on-insulator rib waveguide is realized by using the electron beam lithography followed by inductively coupled plasma etching. The design and the experimental realization of this device are presented in detail. In addition to improving relevant processes to minimize propagation loss, the coupling efficiency between the ring and the bus is carefully chosen to approach a critical coupling for high performance operating. We have measured a quality factor of 21,200 and an extinction ratio of 12.5dB at a resonant wavelength of 1549.32nm. Meanwhile, a low propagation loss of 0.89dB/mm in a curved waveguide with a bending radius of 40 mu m is demonstrated as well.

A Fully Integrated 900-MHz Passive RFID Transponder Front End With Novel Zero-Threshold RF-DC Rectifier

This paper presents a fully integrated CMOS analog front end for a passive 900-MHz radio-frequency identification (RFID) transponder. The power supply in this front end is generated from the received RF electromagnetic energy by using an RF-dc voltage rectifier. In order to improve the compatibility with standard CMOS technology, Schottky diodes in conventional RF-dc rectifiers are replaced by diode-connected MOS transistors with zero threshold. Meanwhile, theoretical analyses for the proposed rectifier are provided and verified by both simulation and measurement results. The design considerations of the pulsewidth-modulation (PWM) demodulator and the backscatter modulator in the front end are also discussed for low-power applications. The proposed front end is implemented in a 0.35-mu m 2P4M CMOS technology. The whole chip occupies a die area of 490 x 780 mu m(2) and consumes only 2.1 mu W in reading mode under a self-generated 1.5-V supply voltage. The measurement results show that the proposed rectifier can properly operate with a - 14.7-dBm input RF power at a power conversion efficiency of 13.0%. In the proposed RFID applications, this sensitivity corresponds to 10.88-m communication distance at 4-W equivalent isotropically radiated power from a reader base station.