Evaluation of wheat or corn dried distillers' grains with solubles on performance and carcass characteristics of feedlot steers

[EN]A study was conducted on crossbred steers (n=275; 376±924 kg) to evaluate performance and carcass quality of cattle fed wheat or corn dried distillers’ grains with solubles (DDGS). The control ration contained 86.6% rolled barley grain, 5.7% supplement and 7.7% barley silage (DM basis). The four treatments included replacement of barley grain at 20 or 40% of the diet (DM basis) with wheat or corn DDGS. Steers were slaughtered at a common end weight of 645 kg with 100 steers randomly (n=20 per treatment) selected for determination of the retail yield of sub-primal boneless boxed beef (SPBBB). Data were analyzed as a completely randomized design using pen as the experimental unit. Feeding increasing levels of wheat DDGS led to a quadratic increase in dry matter intake (DMI) (P<0.01), whereas increasing levels of corn DDGS led to a quadratic decrease in DMI (P=0.01). Average daily gain was not influenced (P=0.13) by feeding wheat or corn DDGS, but cattle fed corn DDGS exhibited a quadratic increase (P=0.01) in gain:feed. As a result, a quadratic increase (P<0.01) in calculated NEg of the diet was observed as corn DDGS levels increased. A linear decrease (P=0.04) in days on feed (169, 166 and 154 d) was noted when increasing levels of wheat DDGS (0, 20 and 40%) were fed. Dressing percentage increased in a linear fashion with wheat DDGS (P<0.01) inclusion level and in a quadratic fashion (P=0.01) as corn DDGS inclusion level increased although other carcass traits were not affected (P=0.10) by treatment. The results indicate that replacement of barley grain with corn or wheat DDGS up to 40% of the diet (DM) can lead to superior performance (improved gain:feed or reduced days on feed, respectively) with no detrimental effect on quality grade or carcass SPBBB yield.

Asymptotic Hyperstability of a Class of Linear Systems under Impulsive Controls Subject to an Integral Popovian Constraint

This paper is focused on the study of the important property of the asymptotic hyperstability of a class of continuous-time dynamic systems. The presence of a parallel connection of a strictly stable subsystem to an asymptotically hyperstable one in the feed-forward loop is allowed while it has also admitted the generation of a finite or infinite number of impulsive control actions which can be combined with a general form of nonimpulsive controls. The asymptotic hyperstability property is guaranteed under a set of sufficiency-type conditions for the impulsive controls.

Effective and Robust Generalized Predictive Speed Control of Induction Motor

14 p.

A Data Dropout Compensation Algorithm Based on the Iterative Learning Control Methodology for Discrete-Time Systems

This paper deals with the convergence of a remote iterative learning control system subject to data dropouts. The system is composed by a set of discrete-time multiple input-multiple output linear models, each one with its corresponding actuator device and its sensor. Each actuator applies the input signals vector to its corresponding model at the sampling instants and the sensor measures the output signals vector. The iterative learning law is processed in a controller located far away of the models so the control signals vector has to be transmitted from the controller to the actuators through transmission channels. Such a law uses the measurements of each model to generate the input vector to be applied to its subsequent model so the measurements of the models have to be transmitted from the sensors to the controller. All transmissions are subject to failures which are described as a binary sequence taking value 1 or 0. A compensation dropout technique is used to replace the lost data in the transmission processes. The convergence to zero of the errors between the output signals vector and a reference one is achieved as the number of models tends to infinity.

Control de almacén automatizado con dos ejes lineales.

[ES]El objetivo principal de este Trabajo Fin de Grado es automatizar un almacén con dos ejes lineales con la meta final de programar un panel de operador para que, ya sea un usuario u operario pueda introducir si desea depositar o recoger un palé, indicando la posición mediante un sistema de coordenadas las cuales dividen a las estanterías del almacén en filas y columnas. Para ello se cambiará parte del hardware de control, el cual incluye el antiguo módulo de posicionamiento (IP 246) que hasta ahora, controlaba el almacén. Esta tarjeta está limitada a un software ya desfasado, sin posibilidad de implementar un panel de operador con los requisitos demandados en la industria de hoy en día. También se ha utilizado una CPU S7-300, a diferencia de la SIMATIC S5 que se utilizaba con la antigua tarjeta.

Análisis de prestaciones de variador de frecuencia Sinamics para el control de velocidad y posición.

[ES]En este documento se exponen los resultados de las diferentes funcionalidades analizadas del variador de frecuencia Sinamics G120. El dispositivo se ha configurado mediante el software de control TIA Portal para la realización de tareas de control de velocidad de un motor de inducción, así como el control de posición del eje del motor y de un eje lineal acoplado al mismo.

On Nonnegative Solutions of Fractional q-Linear Time-Varying Dynamic Systems with Delayed Dynamics

This paper is devoted to the investigation of nonnegative solutions and the stability and asymptotic properties of the solutions of fractional differential dynamic linear time-varying systems involving delayed dynamics with delays. The dynamic systems are described based on q-calculus and Caputo fractional derivatives on any order.