Aportaciones metodológicas a la gestión y explotación de nubes de puntos procedentes de escáneres tridimensionales, aplicados a la documentación geométrica del patrimonio. El caso de la Portada de los Hierros de la Catedral de Valencia

Presentado en: IX Congreso Internacional de Rehabilitación del Patrimonio Arquitectónico y Edificación (Sevilla, España, 9-12 julio 2008)

Erromaurreko Iberiar Penintsulako antzinaroari buruzko materialak : Iberiako hegoaldeko herri eta kulturak

Traducido por Iñaki Villoslada Fernández

Fishing Long-Fingered Bats (Myotis capaccinii) Prey Regularly upon Exotic Fish

7 p.

Streamflow response of a small forested catchment on different timescales

The hydrological response of a catchment to rainfall on different timescales is result of a complex system involving a range of physical processes which may operate simultaneously and have different spatial and temporal influences. This paper presents the analysis of streamflow response of a small humid-temperate catchment (Aixola, 4.8 km(2)) in the Basque Country on different timescales and discusses the role of the controlling factors. Firstly, daily time series analysis was used to establish a hypothesis on the general functioning of the catchment through the relationship between precipitation and discharge on an annual and multiannual scale (2003-2008). Second, rainfall-runoff relationships and relationships among several hydrological variables, including catchment antecedent conditions, were explored at the event scale (222 events) to check and improve the hypothesis. Finally, the evolution of electrical conductivity (EC) during some of the monitored storm events (28 events) was examined to identify the time origin of waters. Quick response of the catchment to almost all the rainfall events as well as a considerable regulation capacity was deduced from the correlation and spectral analyses. These results agree with runoff event scale data analysis; however, the event analysis revealed the non-linearity of the system, as antecedent conditions play a significant role in this catchment. Further, analysis at the event scale made possible to clarify factors controlling (precipitation, precipitation intensity and initial discharge) the different aspects of the runoff response (runoff coefficient and discharge increase) for this catchment. Finally, the evolution of EC of the waters enabled the time origin (event or pre-event waters) of the quickflow to be established; specifically, the conductivity showed that pre-event waters usually represent a high percentage of the total discharge during runoff peaks. The importance of soil waters in the catchment is being studied more deeply.

A Brief Grammar of Euskara, the Basque Language

This is a short grammar of the Basque language, or Euskara as it is called by its speakers. What follows is a partial description of the syntax of Euskara. The text has been arranged in the following fashion: there is an index where you can find the distribution of topics. Within each of the topics, an effort has been made to arrange information from general to specific, so that as you read into a given section, you will get into more details about the topic being under discussion. This grammar hopes to be useful to a wide variety of users. Therefore, it will probably not satisfy anyone completely: Those who want a quick 'feel' for the language will be disappointed by the slow and messy details the text dives into. Those who want a detailed, professional description will be disappointed by the lack of depth in the discussion. The text hopes to sit somewhere in the middle, and if it tells too much to those who want to know a little, and too little to those who want to know a lot, then it will have done its job.

Análisis de la influencia de la orientación de las fibras metálicas en la resistencia de la matriz de hormigón de acuerdo al Ensayo Barcelona

[ES]El objetivo de este trabajo de fin de grado es analizar la influencia que tiene la cuantía y orientación de fibras metálicas presentes en el interior de probetas de hormigón autocompactante y cuyo objetivo es reforzar y aumentar la resistencia a tracción de este material. Se expondrán las propiedades que combina el HACRFA gracias a la autocompactación del hormigón y la inclusión de fibras en su interior y los beneficios que este nuevo material aporta. Por otro lado, se tratara de situar este estudio en un contexto, analizando a la vez cuál es el alcance y los objetivos más importantes que se han tenido en cuenta. A continuación, y a modo de complementación de su contexto, este trabajo tiene un estado del arte, en el que se mencionarán métodos y ensayos necesarios para llegar a un resultado que permita predecir cuál será la resistencia del material, y por tanto su tenacidad o capacidad de absorber energía, sin necesidad de emplear más que un método fácil y rápido, obviando el resto de ensayos destructivos utilizados en este trabajo. Para tal fin, se establece una metodología que, gracias a ensayos de laboratorio, permita establecer una relación entre el método sencillo que se ha mencionado, el método inductivo, y un resultado teórico de la tenacidad que presenta el HACRFA. Se observará cómo la desviación entre los ensayos experimentales y los resultados teóricos obtenidos es prácticamente nula, despreciando situaciones en las que se presenten comportamientos muy diferentes debido a fallos durante los ensayos.

Geology alive. GeoBizirik.org

Geology is the science that studies the Earth, its composition, structure and origin in addition to past and present phenomena that leave their mark on rocks. So why does society need geologists? Some of the main reasons are listed below: - Geologists compile and interpret information about the earth’s surface and subsoil, which allows us to establish the planet’s past history, any foreseeable changes and its relationship with the rest of the solar system. - Society needs natural resources (metals, non-metals, water and fossil fuels) to survive. The work of geologists is therefore a key part of finding new deposits and establishing a guide for exploring and managing resources in an environmentally-friendly way. - The creation of geological maps allows us to identify potential risk areas and survey different land uses; in other words, they make an essential contribution to land planning and proposing sustainable development strategies in a region. - Learning about Geology and the proper use of geological information contributes to saving lives and reducing financial loss caused by natural catastrophes such as earthquakes, tsunamis, volcanic eruptions, flooding and landslides, while also helping to develop construction projects, public works, etc. Through the proposed activities we aim to explain some of the basic elements of the different specialities within the field of Geological Sciences. In order to do this, four sessions have been organised that will allow for a quick insight into the fields of Palaeontology, Mineralogy, Petrology and Tectonics.

Geology alive. GeoBizirik.org

Geology is the science that studies the Earth, its composition, structure and origin in addition to past and present phenomena that leave their mark on rocks. So why does society need geologists? Some of the main reasons are listed below: - Geologists compile and interpret information about the earth’s surface and subsoil, which allows us to establish the planet’s past history, any foreseeable changes and its relationship with the rest of the solar system. - Society needs natural resources (metals, non-metals, water and fossil fuels) to survive. The work of geologists is therefore a key part of finding new deposits and establishing a guide for exploring and managing resources in an environmentally-friendly way. - The creation of geological maps allows us to identify potential risk areas and survey different land uses; in other words, they make an essential contribution to land planning and proposing sustainable development strategies in a region. - Learning about Geology and the proper use of geological information contributes to saving lives and reducing financial loss caused by natural catastrophes such as earthquakes, tsunamis, volcanic eruptions, flooding and landslides, while also helping to develop construction projects, public works, etc. Through the proposed activities we aim to explain some of the basic elements of the different specialities within the field of Geological Sciences. In order to do this, four sessions have been organised that will allow for a quick insight into the fields of Palaeontology, Mineralogy, Petrology and Tectonics.

Advanced Reaction Systems for Hydrogen Production

[EN] This PhD work started in March 2010 with the support of the University of the Basque Country (UPV/EHU) under the program named “Formación de Personal Investigador” at the Chemical and Environmental Engineering Department in the Faculty of Engineering of Bilbao. The major part of the Thesis work was carried out in the mentioned department, as a member of the Sustainable Process Engineering (SuPrEn) research group. In addition, this PhD Thesis includes the research work developed during a period of 6 months at the Institut für Mikrotechnik Mainz GmbH, IMM, in Germany. During the four years of the Thesis, conventional and microreactor systems were tested for several feedstocks renewable and non-renewable, gases and liquids through several reforming processes in order to produce hydrogen. For this purpose, new catalytic formulations which showed high activity, selectivity and stability were design. As a consequence, the PhD work performed allowed the publication of seven scientific articles in peer-reviewed journals. This PhD Thesis is divided into the following six chapters described below. The opportunity of this work is established on the basis of the transition period needed for moving from a petroleum based energy system to a renewable based new one. Consequently, the present global energy scenario was detailed in Chapter 1, and the role of hydrogen as a real alternative in the future energy system was justified based on several outlooks. Therefore, renewable and non-renewable hydrogen production routes were presented, explaining the corresponding benefits and drawbacks. Then, the raw materials used in this Thesis work were described and the most important issues regarding the processes and the characteristics of the catalytic formulations were explained. The introduction chapter finishes by introducing the concepts of decentralized production and process intensification with the use of microreactors. In addition, a small description of these innovative reaction systems and the benefits that entailed their use were also mentioned. In Chapter 2 the main objectives of this Thesis work are summarized. The development of advanced reaction systems for hydrogen rich mixtures production is the main objective. In addition, the use and comparison between two different reaction systems, (fixed bed reactor (FBR) and microreactor), the processing of renewable raw materials, the development of new, active, selective and stable catalytic formulations, and the optimization of the operating conditions were also established as additional partial objectives. Methane and natural gas (NG) steam reforming experimental results obtained when operated with microreactor and FBR systems are presented in Chapter 3. For these experiments nickel-based (Ni/Al2O3 and Ni/MgO) and noble metal-based (Pd/Al2O3 and Pt/Al2O3) catalysts were prepared by wet impregnation and their catalytic activity was measured at several temperatures, from 973 to 1073 K, different S/C ratios, from 1.0 to 2.0, and atmospheric pressure. The Weight Hourly Space Velocity (WHSV) was maintained constant in order to compare the catalytic activity in both reaction systems. The results obtained showed a better performance of the catalysts operating in microreactors. The Ni/MgO catalyst reached the highest hydrogen production yield at 1073 K and steam-to-carbon ratio (S/C) of 1.5 under Steam methane Reforming (SMR) conditions. In addition, this catalyst also showed good activity and stability under NG reforming at S/C=1.0 and 2.0. The Ni/Al2O3 catalyst also showed high activity and good stability and it was the catalyst reaching the highest methane conversion (72.9 %) and H2out/CH4in ratio (2.4) under SMR conditions at 1073 K and S/C=1.0. However, this catalyst suffered from deactivation when it was tested under NG reforming conditions. Regarding the activity measurements carried out with the noble metal-based catalysts in the microreactor systems, they suffered a very quick deactivation, probably because of the effects attributed to carbon deposition, which was detected by Scanning Electron Microscope (SEM). When the FBR was used no catalytic activity was measured with the catalysts under investigation, probably because they were operated at the same WHSV than the microreactors and these WHSVs were too high for FBR system. In Chapter 4 biogas reforming processes were studied. This chapter starts with an introduction explaining the properties of the biogas and the main production routes. Then, the experimental procedure carried out is detailed giving concrete information about the experimental set-up, defining the parameters measured, specifying the characteristics of the reactors used and describing the characterization techniques utilized. Each following section describes the results obtained from activity testing with the different catalysts prepared, which is subsequently summarized: Section 4.3: Biogas reforming processes using γ-Al2O3 based catalysts The activity results obtained by several Ni-based catalysts and a bimetallic Rh-Ni catalyst supported on magnesia or alumina modified with oxides like CeO2 and ZrO2 are presented in this section. In addition, an alumina-based commercial catalyst was tested in order to compare the activity results measured. Four different biogas reforming processes were studied using a FBR: dry reforming (DR), biogas steam reforming (BSR), biogas oxidative reforming (BOR) and tri-reforming (TR). For the BSR process different steam to carbon ratios (S/C) from 1.0 to 3.0, were tested. In the case of BOR process the oxygen-to-methane (O2/CH4) ratio was varied from 0.125 to 0.50. Finally, for TR processes different S/C ratios from 1.0 to 3.0, and O2/CH4 ratios of 0.25 and 0.50 were studied. Then, the catalysts which achieved high activity and stability were impregnated in a microreactor to explore the viability of process intensification. The operation with microreactors was carried out under the best experimental conditions measured in the FBR. In addition, the physicochemical characterization of the fresh and spent catalysts was carried out by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), N2 physisorption, H2 chemisorption, Temperature Programmed Reduction (TPR), SEM, X-ray Photoelectron Spectroscopy (XPS) and X-ray powder Diffraction (XRD). Operating with the FBR, conversions close to the ones predicted by thermodynamic calculations were obtained by most of the catalysts tested. The Rh-Ni/Ce-Al2O3 catalyst obtained the highest hydrogen production yield in DR. In BSR process, the Ni/Ce-Al2O3 catalyst achieved the best activity results operating at S/C=1.0. In the case of BOR process, the Ni/Ce-Zr-Al2O3 catalyst showed the highest reactants conversion values operating at O2/CH4=0.25. Finally, in the TR process the Rh-Ni/Ce-Al2O3 catalyst obtained the best results operating at S/C=1.0 and O2/CH4=0.25. Therefore, these three catalysts were selected to be coated onto microchannels in order to test its performance under BOR and TR processes conditions. Although the operation using microreactors was carried out under considerably higher WHSV, similar conversions and yields as the ones measured in FBR were measured. Furthermore, attending to other measurements like Turnover Frequency (TOF) and Hydrogen Productivity (PROD), the values calculated for the catalysts tested in microreactors were one order of magnitude higher. Thus, due to the low dispersion degree measured by H2-chemisorption, the Ni/Ce-Al2O3 catalyst reached the highest TOF and PROD values. Section 4.4: Biogas reforming processes using Zeolites L based catalysts In this section three type of L zeolites, with different morphology and size, were synthesized and used as catalyst support. Then, for each type of L zeolite three nickel monometallic and their homologous Rh-Ni bimetallic catalysts were prepared by the wetness impregnation method. These catalysts were tested using the FBR under DR process and different conditions of BSR (S/C ratio of 1.0 and 2.0), BOR (O2/CH4 ratio of 0.25 and 0.50) and TR processes (at S/C=1.0 and O2/CH4=0.25). The characterization of these catalysts was also carried out by using the same techniques mentioned in the previous section. Very high methane and carbon dioxide conversion values were measured for almost all the catalysts under investigation. The experimental results evidenced the better catalytic behavior of the bimetallic catalysts as compared to the monometallic ones. Comparing the catalysts behavior with regards to their morphology, for the BSR process the Disc catalysts were the most active ones at the lowest S/C ratio tested. On the contrary, the Cylindrical (30–60 nm) catalysts were more active under BOR conditions at O2/CH4=0.25 and TR processes. By the contrary, the Cylindrical (1–3 µm) catalysts showed the worst activity results for both processes. Section 4.5: Biogas reforming processes using Na+ and Cs+ doped Zeolites LTL based catalysts A method for the synthesis of Linde Type L (LTL) zeolite under microwave-assisted hydrothermal conditions and its behavior as a support for heterogeneously catalyzed hydrogen production is described in this section. Then, rhodium and nickel-based bimetallic catalysts were prepared in order to be tested by DR process and BOR process at O2/CH4=0.25. Moreover, the characterization of the catalysts under investigation was also carried out. Higher activities were achieved by the catalysts prepared from the non-doped zeolites, Rh-Ni/D and Rh-Ni/N, as compared to the ones supported on Na+ and Cs+ exchanged supports. However, the differences between them were not very significant. In addition, the Na+ and Cs+ incorporation affected mainly to the Disc catalysts. Comparing the results obtained by these catalysts with the ones studied in the section 4.4, in general worst results were achieved under DR conditions and almost the same results when operated under BOR conditions. In Chapter 5 the ethylene glycol (EG) as feed for syngas production by steam reforming (SR) and oxidative steam reforming (OSR) was studied by using microchannel reactors. The product composition was determined at a S/C of 4.0, reaction temperatures between 625°C and 725°C, atmospheric pressure and Volume Hourly Space Velocities (VHSV) between 100 and 300 NL/(gcath). This work was divided in two sections. The first one corresponds to the introduction of the main and most promising EG production routes. Then, the new experimental procedure is detailed and the information about the experimental set-up and the measured parameters is described. The characterization was carried out using the same techniques as for the previous chapter. Then, the next sections correspond to the catalytic activity and catalysts characterization results. Section 5.3: xRh-cm and xRh-np catalysts for ethylene glycol reforming Initially, catalysts with different rhodium loading, from 1.0 to 5.0 wt. %, and supported on α-Al2O3 were prepared by two different preparation methods (conventional impregnation and separate nanoparticle synthesis). Then, the catalysts were compared regarding their measured activity and selectivity, as well as the characterization results obtained before and after the activity tests carried out. The samples prepared by a conventional impregnation method showed generally higher activity compared to catalysts prepared from Rh nanoparticles. By-product formation of species such as acetaldehyde, ethane and ethylene was detected, regardless if oxygen was added to the feed or not. Among the catalysts tested, the 2.5Rh-cm catalyst was considered the best one. Section 5.4: 2.5Rh-cm catalyst support modification with CeO2 and La2O3 In this part of the Chapter 5, the catalyst showing the best performance in the previous section, the 2.5Rh-Al2O3 catalyst, was selected in order to be improved. Therefore, new Rh based catalysts were designed using α-Al2O3 and being modified this support with different contents of CeO2 or La2O3 oxides. All the catalysts containing additives showed complete conversion and selectivities close to the equilibrium in both SR and OSR processes. In addition, for these catalysts the concentrations measured for the C2H4, CH4, CH3CHO and C2H6 by-products were very low. Finally, the 2.5Rh-20Ce catalyst was selected according to its catalytic activity and characterization results in order to run a stability test, which lasted more than 115 hours under stable operation. The last chapter, Chapter 6, summarizes the main conclusions achieved throughout this Thesis work. Although very high reactant conversions and rich hydrogen mixtures were obtained using a fixed bed reaction system, the use of microreactors improves the key issues, heat and mass transfer limitations, through which the reforming reactions are intensified. Therefore, they seem to be a very interesting and promising alternative for process intensification and decentralized production for remote application.

Desarrollo de una herramienta virtual destinada al diseño de una plataforma robótica reconfigurable.

[ES]Este proyecto tiene como objeto aumentar el conocimiento concerniente a mecanismos robóticos reconfigurables, así como ponerlo en práctica. Estos mecanismos pueden lograr rápidas transiciones y son capaces de adaptarse a sí mismos a muchos entornos diferentes, conduciendo a una reducción de costes y requerimientos de espacio. Para ello, se estudia el estado del arte, de manera que se pueda reunir información sobre las principales aplicaciones y oportunidades que este campo ofrece en diferentes áreas. A continuación, se requiere llevar a cabo un análisis cinemático de un robot específico, y junto a métodos de planificación de trayectorias, su implementación en un software gráfico para simular su movimiento. La herramienta de software “Matlab” va a ser la que permitirá llevar a cabo toda la programación y representación a lo largo de todo el proyecto.

Strategies for Power Line Communications Smart Metering Network Deployment

Smart Grids are becoming a reality all over the world. Nowadays, the research efforts for the introduction and deployment of these grids are mainly focused on the development of the field of Smart Metering. This emerging application requires the use of technologies to access the significant number of points of supply (PoS) existing in the grid, covering the Low Voltage (LV) segment with the lowest possible costs. Power Line Communications (PLC) have been extensively used in electricity grids for a variety of purposes and, of late, have been the focus of renewed interest. PLC are really well suited for quick and inexpensive pervasive deployments. However, no LV grid is the same in any electricity company (utility), and the particularities of each grid evolution, architecture, circumstances and materials, makes it a challenge to deploy Smart Metering networks with PLC technologies, with the Smart Grid as an ultimate goal. This paper covers the evolution of Smart Metering networks, together with the evolution of PLC technologies until both worlds have converged to project PLC-enabled Smart Metering networks towards Smart Grid. This paper develops guidelines over a set of strategic aspects of PLC Smart Metering network deployment based on the knowledge gathered on real field; and introduces the future challenges of these networks in their evolution towards the Smart Grid.

Eurobalise-Train communication modelling to assess interferences in railway control signalling systems

The evolution of the railway sector depends, to a great extent, on the deployment of advanced railway signalling systems. These signalling systems are based on communication architectures that must cope with complex electromagnetical environments. This paper is outlined in the context of developing the necessary tools to allow the quick deployment of these signalling systems by contributing to an easier analysis of their behaviour under the effect of electromagnetical interferences. Specifically, this paper presents the modelling of the Eurobalise-train communication flow in a general purpose simulation tool. It is critical to guarantee this communication link since any lack of communication may lead to a stop of the train and availability problems. In order to model precisely this communication link we used real measurements done in a laboratory equipped with elements defined in the suitable subsets. Through the simulation study carried out, we obtained performance indicators of the physical layer such as the received power, SNR and BER. The modelling presented in this paper is a required step to be able to provide quality of service indicators related to perturbed scenarios.