La participación ciudadana en la prensa. El caso del diario El Correo y su pionero modelo participativo: "enlace".

425 p.

Fabricación y reparación de geometrías complejas mediante aporte por laser.

El láser cladding es una tecnología en alza. Mediante la energía de una radiación láser, se crea un baño fundido de material que, combinado con la inyección de material en polvo a través de una boquilla y controlando el movimiento a través de la programación de una plataforma cinemática, ofrece la posibilidad de fabricar una geometría determinada mediante la adición de material. Se trata, sin embargo, de un proceso complejo en el que intervienen gran cantidad de fenómenos físicos y resulta complicado obtener un buen resultado en trayectorias complejas. En el presente trabajo se ha tratado el proceso de fabricación de una geometría compleja tipo álabe de turbina. Para ello, se ha comenzado por llevar a cabo una revisión bibliográfica, posteriormente, se han llevado a cabo una serie de ensayos experimentales para la determinación de parámetros de proceso, y finalmente, se ha desarrollado una estrategia de aporte original para estructuras tipo álabe que permite garantizar la estabilidad del proceso. En base a los resultados satisfactorios obtenidos, se ha concluido que mediante la aplicación de la nueva estrategia es posible la generación de geometrías complejas con alto grado de estabilidad.

Transformación martensítica en aleaciones metamagnéticas con memoria de forma.

Las aleaciones con memoria de forma, SMA , son materiales que presentan unas propiedades muy interesantes, como son el efecto de memoria de forma y la superlasticidad. El mecanismo responsable de estas propiedades es la transformación martensítica termo - elástica. Esta transformación , es una transformación sólido - sólido reversible de primer orden , la cual se da entre una fase de alta simetría y otra de menor simetría. La fase de mayor simetría se llama " fase austenita" y la de menor si metría " fase martensita". Las aleaciones metam agnéticas con memoria de forma, MSMA, son aleaciones que aúna n, las propiedades que confiere la transformación martensí tica y las propiedades magnétic as. La característica principal de estas aleaciones es que la fase martensita t iene un carácter magnético más débil que el de la fase austenita, y ello propicia que estas presenten efectos magnetocalóricos, efectos magnetocalóricos inversos y magnetorresistencia. En este Trabajo de Fin de Grado se han elaborado un a serie de seis MSMAs basad as en Mn - Ni - Sn, de composición: Mn 49 Ni 42 - x Sn 9 Fe x (x=0,2,3,4,5,6 en % atómico) en las que se ha sustituido Fe por Ni . Los objet ivo s fundamentales de este trabajo ha n sido , la caracterización de la tran sformación estructural, el estudio de la influencia del campo magnético tanto en la transformación estructural como magnética y por último el estudio de la influencia de la composición en la transformación martensítica y magnética. Para llevar a cabo esta labor se han usado varias técnicas experimentales como son la calorimetría diferencial de barr ido, DSC , la magneto metría de muestra vibrante , VSM , EDX para determinar la composición y Rayos - X para determinar la estructura cristalográfica. A tenor de los resultados obtenidos durante el trabajo, se concluye que , la composición juega un papel fundamental en las propiedades de estas aleaciones, pudiéndose distinguir dos grupos, las aleaciones con 4 % o menos de Fe y con más de 4 % de Fe. La aplicación de campo magnético desplaza la tra nsformación hacia temperaturas bajas, determinando sus diagramas de fase. Debido al estado de no equilibrio de los mismos no se puede determinar la variación l a de entrop í a en función del campo magnético. Por último, l a aparición del fenómeno de "kinetic ar rest" y la fase - son determinantes en el comportamiento de este tipo de aleaciones

Initiatives for the improvement of continuous management training

[EN] Purpose. This work aims to present, from the company viewpoint, a structured account of management proposals and practices directed toward improving the intensity and effectiveness of continuous management training (CMT). Design/methodology/approach. The article takes as its main theoretical referents the Theory of Human Capital, the Resource-Based Vision and the contributions made via the new institutional economy with regard to the problems of information asymmetry between companies, employees and training providers and completes the proposals that derive from this theoretical approach. To do this, experience-based contributions are collected from a selection of company training and HR managers from twelve Basque companies characterised by their strong investment in management training. The methodology used was qualitative and obtained by different qualitative techniques: Focus Groups, Nominal Groups and the Delphi Method, which make up the so-called Hybrid Delphi. Findings and implications. The proposals are aimed at the main agents in training activity: training providers, associations and public agents engaged in management training and, particularly, companies themselves. The initiatives seek above all to increase training market transparency, to improve mutual commitments between companies and managers, and to link training and development with culture and strategic management, so that firms make optimal investment in management training. Originality/value. The methodology used is original, and the contributions are consistent with the theory, have a proven practical utility, and are presented in a hierarchy, which facilitates decision making.

Estudio del efecto de la hidratación de la escoria blanca de acería de HEA: aplicación en pastas y morteros de cemento

xxiv, 252 p.

Cuidados alternativos y complementarios para el manejo del dolor en el paciente crónico y/o paliativo

Desde siempre se han utilizado las terapias alternativas o complementarias (MAC) para tratar los problemas de salud. Hoy en día han ido sustituyéndose por la medicina convencional que conocemos. A pesar de ello, las cifras de personas en el mundo que las utilizan son muy altas. En este trabajo pondremos en el punto de mira el empleo de las MAC por parte de los profesionales de enfermería para el control del dolor en pacientes crónicos y/o paliativos. Objetivos: Describir el estado de la investigación y la evidencia científica de las MAC, analizar su grado de implantación en la formación enfermera y su empleo en los cuidados a pacientes con enfermedades crónicas que puedan requerir unos cuidados paliativos que cursan con dolor e identificar diferentes técnicas de las MAC aplicables al manejo del dolor por parte de enfermería. Metodología: Para alcanzar los objetivos se ha realizado una revisión narrativa. Se ha buscado en diferentes bases de datos utilizando criterios de inclusión y exclusión que han permitido seleccionar las fuentes bibliográficas necesarias. Conclusión: Las MAC demuestran ser eficaces a la hora de realizar los cuidados y controlar el dolor de los pacientes con enfermedades crónicas que puedan requerir de cuidados paliativos, los profesionales de enfermería son aptos para el empleo de las MAC a nivel hospitalario, las MAC son ya utilizadas por los profesionales de enfermería dentro de la medicina convencional, las MAC no sostienen una MBE, no obstante, están respaldadas por numerosas investigaciones que avalan su eficacia.

Advanced Reaction Systems for Hydrogen Production

[EN] This PhD work started in March 2010 with the support of the University of the Basque Country (UPV/EHU) under the program named “Formación de Personal Investigador” at the Chemical and Environmental Engineering Department in the Faculty of Engineering of Bilbao. The major part of the Thesis work was carried out in the mentioned department, as a member of the Sustainable Process Engineering (SuPrEn) research group. In addition, this PhD Thesis includes the research work developed during a period of 6 months at the Institut für Mikrotechnik Mainz GmbH, IMM, in Germany. During the four years of the Thesis, conventional and microreactor systems were tested for several feedstocks renewable and non-renewable, gases and liquids through several reforming processes in order to produce hydrogen. For this purpose, new catalytic formulations which showed high activity, selectivity and stability were design. As a consequence, the PhD work performed allowed the publication of seven scientific articles in peer-reviewed journals. This PhD Thesis is divided into the following six chapters described below. The opportunity of this work is established on the basis of the transition period needed for moving from a petroleum based energy system to a renewable based new one. Consequently, the present global energy scenario was detailed in Chapter 1, and the role of hydrogen as a real alternative in the future energy system was justified based on several outlooks. Therefore, renewable and non-renewable hydrogen production routes were presented, explaining the corresponding benefits and drawbacks. Then, the raw materials used in this Thesis work were described and the most important issues regarding the processes and the characteristics of the catalytic formulations were explained. The introduction chapter finishes by introducing the concepts of decentralized production and process intensification with the use of microreactors. In addition, a small description of these innovative reaction systems and the benefits that entailed their use were also mentioned. In Chapter 2 the main objectives of this Thesis work are summarized. The development of advanced reaction systems for hydrogen rich mixtures production is the main objective. In addition, the use and comparison between two different reaction systems, (fixed bed reactor (FBR) and microreactor), the processing of renewable raw materials, the development of new, active, selective and stable catalytic formulations, and the optimization of the operating conditions were also established as additional partial objectives. Methane and natural gas (NG) steam reforming experimental results obtained when operated with microreactor and FBR systems are presented in Chapter 3. For these experiments nickel-based (Ni/Al2O3 and Ni/MgO) and noble metal-based (Pd/Al2O3 and Pt/Al2O3) catalysts were prepared by wet impregnation and their catalytic activity was measured at several temperatures, from 973 to 1073 K, different S/C ratios, from 1.0 to 2.0, and atmospheric pressure. The Weight Hourly Space Velocity (WHSV) was maintained constant in order to compare the catalytic activity in both reaction systems. The results obtained showed a better performance of the catalysts operating in microreactors. The Ni/MgO catalyst reached the highest hydrogen production yield at 1073 K and steam-to-carbon ratio (S/C) of 1.5 under Steam methane Reforming (SMR) conditions. In addition, this catalyst also showed good activity and stability under NG reforming at S/C=1.0 and 2.0. The Ni/Al2O3 catalyst also showed high activity and good stability and it was the catalyst reaching the highest methane conversion (72.9 %) and H2out/CH4in ratio (2.4) under SMR conditions at 1073 K and S/C=1.0. However, this catalyst suffered from deactivation when it was tested under NG reforming conditions. Regarding the activity measurements carried out with the noble metal-based catalysts in the microreactor systems, they suffered a very quick deactivation, probably because of the effects attributed to carbon deposition, which was detected by Scanning Electron Microscope (SEM). When the FBR was used no catalytic activity was measured with the catalysts under investigation, probably because they were operated at the same WHSV than the microreactors and these WHSVs were too high for FBR system. In Chapter 4 biogas reforming processes were studied. This chapter starts with an introduction explaining the properties of the biogas and the main production routes. Then, the experimental procedure carried out is detailed giving concrete information about the experimental set-up, defining the parameters measured, specifying the characteristics of the reactors used and describing the characterization techniques utilized. Each following section describes the results obtained from activity testing with the different catalysts prepared, which is subsequently summarized: Section 4.3: Biogas reforming processes using γ-Al2O3 based catalysts The activity results obtained by several Ni-based catalysts and a bimetallic Rh-Ni catalyst supported on magnesia or alumina modified with oxides like CeO2 and ZrO2 are presented in this section. In addition, an alumina-based commercial catalyst was tested in order to compare the activity results measured. Four different biogas reforming processes were studied using a FBR: dry reforming (DR), biogas steam reforming (BSR), biogas oxidative reforming (BOR) and tri-reforming (TR). For the BSR process different steam to carbon ratios (S/C) from 1.0 to 3.0, were tested. In the case of BOR process the oxygen-to-methane (O2/CH4) ratio was varied from 0.125 to 0.50. Finally, for TR processes different S/C ratios from 1.0 to 3.0, and O2/CH4 ratios of 0.25 and 0.50 were studied. Then, the catalysts which achieved high activity and stability were impregnated in a microreactor to explore the viability of process intensification. The operation with microreactors was carried out under the best experimental conditions measured in the FBR. In addition, the physicochemical characterization of the fresh and spent catalysts was carried out by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), N2 physisorption, H2 chemisorption, Temperature Programmed Reduction (TPR), SEM, X-ray Photoelectron Spectroscopy (XPS) and X-ray powder Diffraction (XRD). Operating with the FBR, conversions close to the ones predicted by thermodynamic calculations were obtained by most of the catalysts tested. The Rh-Ni/Ce-Al2O3 catalyst obtained the highest hydrogen production yield in DR. In BSR process, the Ni/Ce-Al2O3 catalyst achieved the best activity results operating at S/C=1.0. In the case of BOR process, the Ni/Ce-Zr-Al2O3 catalyst showed the highest reactants conversion values operating at O2/CH4=0.25. Finally, in the TR process the Rh-Ni/Ce-Al2O3 catalyst obtained the best results operating at S/C=1.0 and O2/CH4=0.25. Therefore, these three catalysts were selected to be coated onto microchannels in order to test its performance under BOR and TR processes conditions. Although the operation using microreactors was carried out under considerably higher WHSV, similar conversions and yields as the ones measured in FBR were measured. Furthermore, attending to other measurements like Turnover Frequency (TOF) and Hydrogen Productivity (PROD), the values calculated for the catalysts tested in microreactors were one order of magnitude higher. Thus, due to the low dispersion degree measured by H2-chemisorption, the Ni/Ce-Al2O3 catalyst reached the highest TOF and PROD values. Section 4.4: Biogas reforming processes using Zeolites L based catalysts In this section three type of L zeolites, with different morphology and size, were synthesized and used as catalyst support. Then, for each type of L zeolite three nickel monometallic and their homologous Rh-Ni bimetallic catalysts were prepared by the wetness impregnation method. These catalysts were tested using the FBR under DR process and different conditions of BSR (S/C ratio of 1.0 and 2.0), BOR (O2/CH4 ratio of 0.25 and 0.50) and TR processes (at S/C=1.0 and O2/CH4=0.25). The characterization of these catalysts was also carried out by using the same techniques mentioned in the previous section. Very high methane and carbon dioxide conversion values were measured for almost all the catalysts under investigation. The experimental results evidenced the better catalytic behavior of the bimetallic catalysts as compared to the monometallic ones. Comparing the catalysts behavior with regards to their morphology, for the BSR process the Disc catalysts were the most active ones at the lowest S/C ratio tested. On the contrary, the Cylindrical (30–60 nm) catalysts were more active under BOR conditions at O2/CH4=0.25 and TR processes. By the contrary, the Cylindrical (1–3 µm) catalysts showed the worst activity results for both processes. Section 4.5: Biogas reforming processes using Na+ and Cs+ doped Zeolites LTL based catalysts A method for the synthesis of Linde Type L (LTL) zeolite under microwave-assisted hydrothermal conditions and its behavior as a support for heterogeneously catalyzed hydrogen production is described in this section. Then, rhodium and nickel-based bimetallic catalysts were prepared in order to be tested by DR process and BOR process at O2/CH4=0.25. Moreover, the characterization of the catalysts under investigation was also carried out. Higher activities were achieved by the catalysts prepared from the non-doped zeolites, Rh-Ni/D and Rh-Ni/N, as compared to the ones supported on Na+ and Cs+ exchanged supports. However, the differences between them were not very significant. In addition, the Na+ and Cs+ incorporation affected mainly to the Disc catalysts. Comparing the results obtained by these catalysts with the ones studied in the section 4.4, in general worst results were achieved under DR conditions and almost the same results when operated under BOR conditions. In Chapter 5 the ethylene glycol (EG) as feed for syngas production by steam reforming (SR) and oxidative steam reforming (OSR) was studied by using microchannel reactors. The product composition was determined at a S/C of 4.0, reaction temperatures between 625°C and 725°C, atmospheric pressure and Volume Hourly Space Velocities (VHSV) between 100 and 300 NL/(gcath). This work was divided in two sections. The first one corresponds to the introduction of the main and most promising EG production routes. Then, the new experimental procedure is detailed and the information about the experimental set-up and the measured parameters is described. The characterization was carried out using the same techniques as for the previous chapter. Then, the next sections correspond to the catalytic activity and catalysts characterization results. Section 5.3: xRh-cm and xRh-np catalysts for ethylene glycol reforming Initially, catalysts with different rhodium loading, from 1.0 to 5.0 wt. %, and supported on α-Al2O3 were prepared by two different preparation methods (conventional impregnation and separate nanoparticle synthesis). Then, the catalysts were compared regarding their measured activity and selectivity, as well as the characterization results obtained before and after the activity tests carried out. The samples prepared by a conventional impregnation method showed generally higher activity compared to catalysts prepared from Rh nanoparticles. By-product formation of species such as acetaldehyde, ethane and ethylene was detected, regardless if oxygen was added to the feed or not. Among the catalysts tested, the 2.5Rh-cm catalyst was considered the best one. Section 5.4: 2.5Rh-cm catalyst support modification with CeO2 and La2O3 In this part of the Chapter 5, the catalyst showing the best performance in the previous section, the 2.5Rh-Al2O3 catalyst, was selected in order to be improved. Therefore, new Rh based catalysts were designed using α-Al2O3 and being modified this support with different contents of CeO2 or La2O3 oxides. All the catalysts containing additives showed complete conversion and selectivities close to the equilibrium in both SR and OSR processes. In addition, for these catalysts the concentrations measured for the C2H4, CH4, CH3CHO and C2H6 by-products were very low. Finally, the 2.5Rh-20Ce catalyst was selected according to its catalytic activity and characterization results in order to run a stability test, which lasted more than 115 hours under stable operation. The last chapter, Chapter 6, summarizes the main conclusions achieved throughout this Thesis work. Although very high reactant conversions and rich hydrogen mixtures were obtained using a fixed bed reaction system, the use of microreactors improves the key issues, heat and mass transfer limitations, through which the reforming reactions are intensified. Therefore, they seem to be a very interesting and promising alternative for process intensification and decentralized production for remote application.

Análisis comparativo de traducciones comerciales en medios audiovisuales. Subtitulado. Traducción de los referentes culturales en "Madagascar 3"

E-mail de contacto: juliaramosdelvalle@gmail.com

Solutions for New Terrestrial Broadcasting Systems Offering Simultaneously Stationary and Mobile Services

221 p.

Charge and spin transport in graphene devices

170 p.

Measurement of polycyclic aromatic hydrocarbons in ambient air by fluorescence spectroscopic techniques

250 p. + anexos

Régimen económico matrimonial en defecto de pacto y derecho internacional privado: determinación de la ley aplicable

El objetivo del Trabajo de Fin de Grado ha sido combinar tres bloques de análisis: el derecho normativo interno español en materia de derecho internacional privado, el derecho comparado en el marco de la Unión Europea y el derecho europeo (los reglamentos en vigor) y los dos proyectos de reglamento en esta materia actualmente en tramitación. Mediante el trabajo se persigue demostrar la necesidad y oportunidad de que el derecho europeo, sin armonizar sustantivamente las regulaciones de cada estado miembro, utilice las técnicas del derecho internacional para seleccionar el Tribunal competente, designar la ley aplicable reconocimiento y ejecución de decisiones judiciales en materia del derecho de familia internacional y centrándonos en el sector de régimen económico matrimonial en defecto de pacto.

La industria de los hidrocarburos: el sector upstream y la operación de lifting de un FPSO

Es un trabajo que pretende dar a conocer de una manera sencilla uno de los sectores de gran importancia en la industria de los hidrocarburos el “UPSTREAM”, que es tan solo el primer bloque de esta industria tan compleja y tan importante a nivel mundial. De esta misma forma dar a conocer los pasos que se toman en una operación de “Lifting” de un FPSO así como la importancia del rol de egresados de náutica en este tipo de operaciones."

Contributions to learning Bayesian network models from weakly supervised data: Application to Assisted Reproductive Technologies and Software Defect Classification

162 p.

Sistema de control y supervisión para una instalación industrial basado en técnicas de computación en la nube.

[ES]Hasta ahora, el control y monitorización de una instalación industrial se realiza desde la sala de control situada en las propias instalaciones de la planta. Cada unidad de control guarda y envía los datos a un ordenador que después se envían a uno central, siguiendo un orden jerárquico, en el que se visualizan ante un operario. Hoy en día, sin embargo, con el auge de los dispositivos móviles inteligentes, se puede conseguir que esa supervisión de la planta industrial se pueda hacer desde cualquier lugar. Podemos visualizar esos datos de control en nuestra mano y mandar órdenes a cada unidad desde nuestro teléfono inteligente. Esto es lo que se ha conseguido hacer con este proyecto, en el que se ha modelizado una instalación industrial basada en una cadena de montaje con tres unidades.