Dynamic response of hydro power plants for providing secondary regulation reserves considering elastic water column effects

In this paper, the dynamic response of a hydro power plant for providing secondary regulation reserve is studied in detail. Special emphasis is given to the elastic water column effects both in the penstock and the tailrace tunnel. For this purpose, a nonlinear model based on the analogy between mass and momentum conservation equations of a water conduit and those of wave propagation in transmission lines is used. The influence of the plant configuration and design parameters on the fulfilment of the Spanish Electrical System Operator requirements is analysed

Pond head level control in a run-of-river hydro power plant using fuzzy controller

The run-of-river hydro power plant usually have low or nil water storage capacity, and therefore an adequate control strategy is required to keep the water level constant in pond. This paper presents a novel technique based on TSK fuzzy controller to maintain the pond head constant. The performance is investigated over a wide range of hill curve of hydro turbine. The results are compared with PI controller as discussed in [1].

Dynamic response of hydro power plants to load variations for providing secondary regulation reserves considering elastic water column effects

In this paper, the dynamic response of a hydro power plant for providing secondary regulation reserve is studied in detail. S pecial emphasis is given to the elastic water column effects both in the penstock and the tailrace tunnel. For this purpose, a nonline ar model based on the analogy between mass and momentum conservation equations of a water conduit and those of wave propagation in transmission lines is used. The influence of the plant configuration and design parameters on the fulfilment of the Spanish Electrical System Operator requirem ents is analysed.

Characteristic study, its identification and self-tuned approach to control hydro-power plants

The water time constant and mechanical time constant greatly influences the power and speed oscillations of hydro-turbine-generator unit. This paper discusses the turbine power transients in response to different nature and changes in the gate position. The work presented here analyses the characteristics of hydraulic system with an emphasis on changes in the above time constants. The simulation study is based on mathematical first-, second-, third- and fourth-order transfer function models. The study is further extended to identify discrete time-domain models and their characteristic representation without noise and with noise content of 10 & 20 dB signal-to-noise ratio (SNR). The use of self-tuned control approach in minimising the speed deviation under plant parameter changes and disturbances is also discussed.

El papel de la hidroelectricidad en el contexto de las energías renovables en España

En el artículo se discute el papel de la energía hidroeléctrica en el marco del sistema eléctrico español, donde existe una elevada penetración de energías no gestionables con una tendencia clara a aumentar en los próximos años. El desarrollo de nuevas centrales hidroeléctricas se basará probablemente en centrales reversibles. La energía hidroeléctrica es una tecnología madura y eficiente para el almacenamiento de energía a gran escala y contribuye por tanto de manera decisiva a la integración de fuentes renovables no gestionables. Los beneficios obtenidos con la operación punta-valle pueden ser insuficientes para compensar el coste de una nueva central. Sin embargo, los ingresos obtenidos pueden incrementarse sustancialmente mediante su participación en los servicios de ajuste del sistema. Ello requeriría un diseño apropiado del mercado eléctrico. La contribución de las centrales hidráulicas reversibles al balance producción-consumo puede extenderse a las horas valle utilizando, bien bombeo en velocidad variable o bien una configuración de cortocircuito hidráulico. La necesidad de mitigar los efectos hidrológicos aguas abajo de las centrales hidroeléctricas puede introducir algunas restricciones en la operación que limitaría de algún modo los servicios descritos más arriba. Sin embargo, cabe esperar que los efectos ambientales provocados por las centrales hidráulicas reversibles sean significativamente menores. In this paper the role of hydropower in electric power systems is discussed, in the framework of the Spanish system, where a high penetration of intermittent power sources exists, showing a clear trend to increase in next years. The development of new hydro power facilities will be likely based on pumped storage hydro power plants. Hydropower is a mature and efficient technology for large-scale energy storage and therefore represents a key contribution for the integration of intermittent power sources, such as wind or photovoltaic. The benefits obtained from load shifting may be insufficient to compensate the costs of a new plant. However, the obtained revenues can significantly increase through its contribution to providing ancillary services. This would require an appropriate design of the electricity market. The contribution of pumped storage hydro power plants to balancing services can be extended to off-peak hours, using either variable speed pumping or the hydraulic shortcircuit configuration. The need to mitigate hydrological effects downstream of hydro plants may introduce some operational constraints which could limit to some extent the services described above. However environmental effects caused by pumped storage hydro power plants are expected to be significantly smaller.

Energía Minihidráulica

La energía basada en turbinas hidráulicas de reducida potencia es, a menudo, un ejemplo- modelo dentro del campo de las energías renovables desde su aparición a finales del S. XIX, aunque los ingenios precursores surgen mucho antes. Entre los testimonios más antiguos destacan la saqia o rueda persa y la rueda hidráulica romana que había sido previamente implementada en Extremo Oriente, y que después llega a Europa a través de Egipto. Más tarde, durante la Edad Media y el Renacimiento, se generaliza el uso de los molinos hidráulicos, además de los eólicos. Ejemplos de ello son las norias de Alepo (Siria) y de Córdoba (España). Otro caso interesante es el de los molinos de regolfo en la Península Ibérica e Iberoamérica, muy cercanos en su forma y fundamentos a las turbinas hidráulicas. Algunos de estos ingenios siguen activos en los ríos de España. Posteriormente los estudios de Euler, Burdin y Fourneyron prepararon las bases para el definitivo avance de Pelton, Kaplan, Francis, y otros, pero ya como máquinas motrices de los generadores eléctricos. En la actualidad, se admite como límite superior para minihidráulica aquellas centrales con una potencia instalada de 5000 kW, y considerando que cuando las potencias son inferiores a 100 kW se denomina micro hidráulica, aunque en Latinoamérica este límite se fija en 20 kW. El estudio del recurso hídrico, ayudado del geotécnico, constituyen la base sobre la que podremos proyectar el aprovechamiento hidroeléctrico: selección del tipo de central dentro de la tipología disponible, diseño y cálculos de la turbina, obra civil necesaria (azud, presa, canal, tubería forzada, edificio, aspiración, desagüe, etc.) y equipo electromecánico. El proyecto tecnológico se complementa con el estudio de impacto ambiental y de viabilidad económica. Muchos de estos proyectos tratan de reducir la falta de acceso a la energía en poblaciones desfavorecidas, entendida esta carencia como un factor determinante de la pobreza. Así la energía mini y micro-hidráulica adquiere un nuevo valor como tecnología para el desarrollo humano.

Contribution to Load-Frequency Regulation of a Hydropower Plant with Long Tail-Race Tunnel

In this paper, a hydroelectric power plant with long tail-race tunnel has been modelled for assessing its contribution to secondary regulation reserve. Cavitation problems, caused by the discharge conduit length, are expected downstream the turbine where low pressure appears during regulation manoeuvres. Therefore, governor's gains should be selected taking into account these phenomena. On the other hand, regulation services bidden by the plant operator should fulfil TSO (Transmission System Operator) quality requirements. A methodology for tuning governor PI gains is proposed and applied to a Hydro power plant in pre-design phase in northwest area of Spain. The PI gains adjustment proposed provides a proper plant response, according to some established indexes, while avoiding cavitation phenomena.

Energías renovables en el sistema marítimo portuario : aprovechamiento energétio de los molinos de marea

Desde el siglo VIII hasta prácticamente el siglo XX, los molinos de marea han sido una fuente de desarrollo de las zonas en las que estaban implantados. En toda la costa atlántica de Europa, y posteriormente en América, se desarrollaron estos ingenios conectados por su naturaleza con los puertos. En ellos se procesaban materia prima que tenía su origen o destino en dichos puertos. La aparición de otras fuentes de energía más económicas y eficaces supuso la decadencia paulatina de estos ingenios, hasta la práctica desaparición de un buen número de ellos. En los últimos años, tanto instituciones privadas como públicas, especialmente ayuntamientos han mostrado un interés en conservar estos ingenios ya sea como edificación singular en el que se desarrollen distintos negocios, o como museos o “centros de interpretación” en los que se explica el funcionamiento del molino y su relación con la comarca de influencia. Este nuevo interés por el tema, unido a la necesidad de buscar nuevas fuentes de energías renovables para dar cumplimento a las condiciones del Tratado de Kyoto motivan la necesidad de un estudio de la aplicación de la energía minihidráulica a los antiguos molinos. En el presente documento se ha procedido en primer lugar a describir la historia de los molinos de marea y a continuación a localizarlos en cada provincia para identificar los posibles puntos de producción de energía. Seguidamente se procedió a identificar los diferentes tipos de turbinas aplicables a estos casos, de los que se han elegido dos de ellos, uno de ellos consolidado y el otro en fase experimental, para determinar y analizar la tendencia de determinadas magnitudes financieras en función de la carrera de marea. Las conclusiones resultantes de este análisis han sido que el sistema de funcionamiento mediante el flujo de la marea es menos productivo que mediante reflujo y que la altura de marea en las costas españolas limita considerablemente la rentabilidad de la inversión. Esta circunstancia obliga a hacer un estudio de viabilidad muy detallado de cada uno de los casos. Las investigaciones futuras en este campo se deben encaminar hacia el desarrollo de un nuevo tipo de miniturbina con una mayor regulación para obtener un mayor rendimiento, teniendo en cuenta, además, que el estuario de un molino de marea puede ser además un excelente banco de pruebas. Por otro lado, la posible producción de energía puede ser un elemento a estudiar dentro de un sistema de generación distribuida en el ámbito de una smart-city. From the eighth century until practically the twentieth century, the tide mills have been a source of development of the areas in which they were implanted. Across the Atlantic coast of Europe, and subsequently in America, these devices were developed and connected by its nature with the nearby ports. In these places the raw material, with its origin and destination from these ports, were processed. The emergence of other sources of energy more economic and efficient caused the gradual decline of these devices which led to the disappearance of a large number of them. In recent years, both private and public institutions, especially municipalities, have shown interest in preserving these devices as singular buildings, or as museums or "visitor centers" where the process of milling is explained and also its relationship with the region of influence. This renewed interest in the subject, coupled with the need of finding new sources of renewable energy in order to comply with the conditions of the Kyoto Treaty, has created the need for a study of the possible implementation of small hydro power in the old mills. In the present document, first we have proceeded to describe the history of the tide mills and afterwards we have located them in the Spanish provinces to identify the possible locations of energy generation. In the next step, we proceeded to identify the different types of turbines suitable to these cases, and we have been selected two of them. The first one is consolidated and the second one is in an experimental phase. With these pair of turbines we have determined and analyzed the outcome of certain financial data depending on the tidal range. The conclusions drawn from this analysis are that operating the system by the flow tide is less productive than by ebb tide. The limited height of tide in the Spanish coast considerably limits the return on investment. This outcome forces potential investors to make a very detailed analysis of each case study. Future researches in this field should be guided towards the development of a new type of mini turbine with more regulation for a higher performance, taking into account also that the basin of a tidal mill can also be an excellent test place. Furthermore, the potential energy output can be a factor to consider in a distributed generation system within a smart city.

Design parameters for continuously variable power-split transmissions using planetaries with 3 active shafts

Since 1996, when the first agricultural tractor with CVT transmission was shown, the presence of this type of transmissions has been increasing. All companies offer them in their products range. Nevertheless, there is little technical documentation that explains the basics of its operation. This report shows all types of CVT transmissions: non-power-split type and power-split ones, as well as the three types used in agricultural tractors, hydro-mechanical power-split transmissions (3 active shafts, input coupled planetary; 3 active shafts, output coupled planetary and 4 active shafts). The report also describes the design parameters of a type of CVT transmission, which use a power-split system with 3 active shafts as well as the fundamental relations among them. Crown Copyright 2010 Published by Elsevier Ltd. on behalf of ISTVS. All rights reserved.

Power system stability of a small sized isolated network supplied by a combined wind-pumped storage generation system: a case study in the Canary Islands

Massive integration of renewable energy sources in electrical power systems of remote islands is a subject of current interest. The increasing cost of fossil fuels, transport costs to isolated sites and environmental concerns constitute a serious drawback to the use of conventional fossil fuel plants. In a weak electrical grid, as it is typical on an island, if a large amount of conventional generation is substituted by renewable energy sources, power system safety and stability can be compromised, in the case of large grid disturbances. In this work, a model for transient stability analysis of an isolated electrical grid exclusively fed from a combination of renewable energy sources has been studied. This new generation model will be installed in El Hierro Island, in Spain. Additionally, an operation strategy to coordinate the generation units (wind, hydro) is also established. Attention is given to the assessment of inertial energy and reactive current to guarantee power system stability against large disturbances. The effectiveness of the proposed strategy is shown by means of simulation results.

Power-frequency control of hydropower plants with long penstocks in isolated systems with wind generation

In this paper the power-frequency control of hydropower plants with long penstocks is addressed. In such configuration the effects of pressure waves cannot be neglected and therefore commonly used criteria for adjustment of PID governors would not be appropriate. A second-order Π model of the turbine-penstock based on a lumped parameter approach is considered. A correction factor is introduced in order to approximate the model frequency response to the continuous case in the frequency interval of interest. Using this model, several criteria are analysed for adjusting the PI governor of a hydropower plant operating in an isolated system. Practical criteria for adjusting the PI governor are given. The results are applied to a real case of a small island where the objective is to achieve a generation 100% renewable (wind and hydro). Frequency control is supposed to be provided exclusively by the hydropower plant. It is verified that the usual criterion for tuning the PI controller of isolated hydro plants gives poor results. However, with the new proposed adjustment, the time response is considerably improved

Conceptual design of offshore platform supply vessel based on hybrid diesel generator-fuel cell power plant

Nowadays increasing fuel prices and upcoming pollutant emission regulations are becoming a growing concern for the shipping industry worldwide. While fuel prices will keep rising in future years, the new International Convention for the Prevention of Pollution from Ships (MARPOL) and Sulphur Emissions Control Areas (SECA) regulations will forbid ships to use heavy fuel oils at certain situations. To fulfil with these regulations, the next step in the marine shipping business will comprise the use of cleaner fuels on board as well as developing new propulsion concept. In this work a new conceptual marine propulsion system is developed, based on the integration of diesel generators with fuel cells in a 2850 metric tonne of deadweight platform supply vessel. The efficiency of the two 250 kW methanol-fed Solid Oxide Fuel Cell (SOFC) system installed on board combined with the hydro dynamically optimized design of the hull of the ship will allow the ship to successfully operate at certain modes of operation while notably reduce the pollutant emissions to the atmosphere. Besides the cogeneration heat obtained from the fuel cell system will be used to answer different heating needs on board the vessel

Improved high-speed de-excitation system for brushless synchronous machines tested on a 20 MVA hydro-generator

Synchronous machines with brushless excitation have the disadvantage that the field winding is not accessible for the de-excitation of the machine. This means that, despite the proper operation of the protection system, the slow de-excitation time constant may produce severe damage in the event of an internal short circuit. A high-speed de-excitation system for these machines was developed, and this study presents the continuation of a previously published study. This study presents the design by computer simulation and the results of the first commissioning of this de-excitation system in a commercial 20 MVA hydro-generator. The de-excitation is achieved by inserting resistance in the field circuit, obtaining a dynamic response similar to that achieved in machines with static excitation. In this case, a non-linear discharge resistor was used, making the dynamic response even better.