Consideration of Multi-Phase Criterion in the Differential Protection Algorithm for High-Impedance Grounded Synchronous Generators

The generator differential protection is one of the most important electrical protections of synchronous generator stator windings. Its operation principle is based on the comparison of the input current and output current at each phase winding. Unwanted trip commands are usually caused by CT saturation, wrong CT selection, or the fact that they may come from different manufacturers. In generators grounded through high impedance, only phase-to-phase or three-phase faults can be detected by the differential protection. This kind of fault causes differential current to flow in, at least, two phases of the winding. Several cases of unwanted trip commands caused by the appearance of differential current in only one phase of the generator have been reported. In this paper multi-phase criterion is proposed for generator differential protection algorithm when applied to high impedance grounded generators.

High-Acoustic-Impedance Tantalum Oxide Layers for Insulating Acoustic Reflectors

This work describes the assessment of the acoustic properties of sputtered tantalum oxide films intended for use as high-impedance films of acoustic reflectors for solidly mounted resonators operating in the gigahertz frequency range. The films are grown by sputtering a metallic tantalum target under different oxygen and argon gas mixtures, total pressures, pulsed dc powers, and substrate biases. The structural properties of the films are assessed through infrared absorption spectroscopy and X-ray diffraction measurements. Their acoustic impedance is assessed by deriving the mass density from X-ray reflectometry measurements and the acoustic velocity from picosecond acoustic spectroscopy and the analysis of the frequency response of the test resonators.

High precision pressure sensors based on SAW devices in the GHz range

In this paper, an AlN/free-standing nanocrystalline diamond (NCD) system is proposed in order to process high frequency surface acoustic wave (SAW) resonators for sensing applications. The main problem of synthetic diamond is its high surface roughness that worsens the sputtered AlN quality and hence the device response. In order to study the feasibility of this structure, AlN films from 150 nm up to 1200 nm thick have been deposited on free-standing NCD. We have then analysed the influence of the AlN layer thickness on its crystal quality and device response. Optimized thin films of 300 nm have been used to fabricate of one-port SAW resonators operating in the 10–14 GHz frequency range. A SAW based sensor pressure with a sensibility of 0.33 MHz/bar has been fabricated.

Optimization of AlN thin layers on diamond substrates for high frequency SAW resonators

AlN/diamond heterostructures are very promising for high frequency surface acoustic wave (SAW) resonators. In their design, the thickness of the piezoelectric film is one of the key parameters. On the other hand, the film material quality and, hence, the device performance, also depend on that thickness. In this work, polished microcrystalline diamond substrates have been used to deposit AlN films by reactive sputtering, from 150 nm up to 3 μm thick. A high degree of the c-axis orientation has been obtained in all cases. SAW one port resonators at high frequency have been fabricated on these films with a proper combination of the film thickness and transducer size.

Super-high-frequency SAW resonators on AlN/Diamond

This letter describes the procedure to manufacture high-performance surface acoustic wave (SAW) resonators on AlN/diamond heterostructures working at frequencies beyond 10 GHz. In the design of SAW devices on AlN/diamond systems, the thickness of the piezoelectric layer is a key parameter. The influence of the film thickness on the SAW device response has been studied. Optimized thin films combined with advanced e-beam lithographic techniques have allowed the fabrication of one-port SAW resonators with finger width and pitch of 200 nm operating in the 10–14 GHz range with up to 36 dB out-of-band rejection.

Characterization of Amorphous Tantalum Oxide for Insulating Acoustic Mirrors

This work describes the assessment of the acoustic properties of sputtered tantalum oxide films intended as high impedance films for the acoustic isolation of bulk acoustic wave devices operating in the GHz frequency range. The films are grown by sputtering a metallic tantalum target under different oxygen and argon gas mixtures, total pressures, pulsed DC powers and substrate bias. The structural properties of the films are assessed through infrared absorption spectroscopy and X-ray diffraction measurements. Their acoustic impedance is obtained after estimating the mass density by X-ray reflectometry measurements and the longitudinal acoustic velocity by analyzing the longitudinal λ/2 resonance induced in a tantalum oxide film inserted between an acoustic reflector and an AlN-based resonator. A second measurement of the sound velocity is achieved through picosecond acoustic spectroscopy.

Diseño de los sistemas de comunicación en plantas de exploración y producción de hidrocarburos

Las plantas industriales de exploración y producción de petróleo y gas disponen de numerosos sistemas de comunicación que permiten el correcto funcionamiento de los procesos que tienen lugar en ella así como la seguridad de la propia planta. Para el presente Proyecto Fin de Carrera se ha llevado a cabo el diseño del sistema de megafonía PAGA (Public Address and General Alarm) y del circuito cerrado de televisión (CCTV) en la unidad de procesos Hydrocrcaker encargada del craqueo de hidrógeno. Partiendo de los requisitos definidos por las especificaciones corporativas de los grupos petroleros para ambos sistemas, PAGA y CCTV, se han expuesto los principios teóricos sobre los que se fundamenta cada uno de ellos y las pautas a seguir para el diseño y demostración del buen funcionamiento a partir de software específico. Se ha empleado las siguientes herramientas software: EASE para la simulación acústica, PSpice para la simulación eléctrica de las etapas de amplificación en la megafonía; y JVSG para el diseño de CCTV. La sonorización tanto de las unidades como del resto de instalaciones interiores ha de garantizar la inteligibilidad de los mensajes transmitidos. La realización de una simulación acústica permite conocer cómo va a ser el comportamiento de la megafonía sin necesidad de instalar el sistema, lo cual es muy útil para este tipo de proyectos cuya ingeniería se realiza previamente a la construcción de la planta. Además se comprueba el correcto diseño de las etapas de amplificación basadas en líneas de alta impedancia o de tensión constante (100 V). El circuito cerrado de televisión (CCTV) garantiza la transmisión de señales visuales de todos los accesos a las instalaciones y unidades de la planta así como la visión en tiempo real del correcto funcionamiento de los procesos químicos llevados a cabo en la refinería. El sistema dispone de puestos de control remoto para el manejo y gestión de las cámaras desplegadas; y de un sistema de almacenamiento de las grabaciones en discos duros (RAID-5) a través de una red SAN (Storage Area Network). Se especifican las diferentes fases de un proyecto de ingeniería en el sector de E&P de hidrocarburos entre las que se destaca: propuesta y adquisición, reunión de arranque (KOM, Kick Off Meeting), estudio in situ (Site Survey), plan de proyecto, diseño y documentación, procedimientos de pruebas, instalación, puesta en marcha y aceptaciones del sistema. Se opta por utilizar terminología inglesa dado al ámbito global del sector. En la última parte del proyecto se presenta un presupuesto aproximado de los materiales empleados en el diseño de PAGA y CCTV. ABSTRACT. Integrated communications for Oil and Gas allows reducing risks, improving productivity, reducing costs, and countering threats to safety and security. Both PAGA system (Public Address and General Alarm) and Closed Circuit Television have been designed for this project in order to ensure a reliable security of an oil refinery. Based on the requirements defined by corporate specifications for both systems (PAGA and CCTV), theoretical principles have been presented as well as the guidelines for the design and demonstration of a reliable design. The following software has been used: EASE for acoustic simulation; PSpice for simulation of the megaphony amplification loops; and JVSG tool for CCTV design. Acoustic for both the units and the other indoor facilities must ensure intelligibility of the transmitted messages. An acoustic simulation allows us to know how will be the performance of the PAGA system without installing loudspeakers, which is very useful for this type of project whose engineering is performed prior to the construction of the plant. Furthermore, it has been verified the correct design of the amplifier stages based on high impedance lines or constant voltage (100 V). Closed circuit television (CCTV) ensures the transmission of visual signals of all access to facilities as well as real-time view of the proper functioning of chemical processes carried out at the refinery. The system has remote control stations for the handling and management of deployed cameras. It is also included a storage system of the recordings on hard drives (RAID - 5) through a SAN (Storage Area Network). Phases of an engineering project in Oil and Gas are defined in the current project. It includes: proposal and acquisition, kick-off meeting (KOM), Site Survey, project plan, design and documentation, testing procedures (SAT and FAT), installation, commissioning and acceptance of the systems. Finally, it has been presented an estimate budget of the materials used in the design of PAGA and CCTV.

Evaluation of the Grounding Circuit Measurements for Stator Ground-Fault Location of Synchronous Generators

Locating stator-winding ground faults accurately is a very difficult task. In this paper the grounding circuit measurements are evaluated in order to obtain information about the stator ground-fault location in synchronous generators. In power generators grounded through a high impedance, the relation between the neutral voltage and the phase voltage provide a first estimation of the fault location. The location error by using this ratio depends on the fault resistance and the value of the capacitance to ground of the stator winding. However, the error added by ignoring the value of the fault resistance is the most relevant term. This location estimation and the location error have been evaluated through the data of a real synchronous machine.

Liquid crystal temperature sensor based on a micrometric structure and a metallic nanometric layer

This letter presents a novel temperature sensor, which consists of an interdigitated comb electrode structure with a micrometric-scale size, nanometric metallic layer, and nematic liquid crystal (NLC) film. This sensor exploits the permittivity dependence of the NLC with temperature and principle of electrical conductivity above the percolation threshold in thin film metallic layers. The latter has been demonstrated to increase the temperature sensitivity considerably. The high impedance input reduces the power dissipation, and the high enough voltage output makes it easy to measure the output signal with high precision. The operation principle and fabrication process as well as the characterization of the temperature sensor are presented. Experimental results show that the device offers a sensitivity of 9 mV/°C and is dependent on the applied voltage. This is six times greater than the same structure without the use of a nanometric layer.

Polyaniline-coated carbon papers for supercapacitor electrodes

Graphene and carbon nanotubes are promising materials for supercapacitor electrodes because of their high specific surface area and excellent electrical, thermal, and mechanical properties. However, these materials suffer from a high manufacturing cost and some aggregation of graphene layers or the presence of toxic residual metallic impurities of carbon nanotubes.

Laser Shock Processing: An Emerging Technique for the Enhancement of Surface Properties and Fatigue Life of High Strength Metal Alloys

Profiting by the increasing availability of laser sources delivering intensities above 10 9 W/cm 2 with pulse energies in the range of several Joules and pulse widths in the range of nanoseconds, laser shock processing (LSP) is being consolidating as an effective technology for the improvement of surface mechanical and corrosion resistance properties of metals and is being developed as a practical process amenable to production engineering. The main acknowledged advantage of the laser shock processing technique consists on its capability of inducing a relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly, the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Following a short description of the theoretical/computational and experimental methods developed by the authors for the predictive assessment and experimental implementation of LSP treatments, experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (specifically steels and Al and Ti alloys) under different LSP irradiation conditions are presented

An Asymptotic Solution for Surface Fields on a Dielectric-Coated Circular Cylinder with an Effective Impedance Boundary Condition.

Reverberation chambers are well known for providing a random-like electric field distribution. Detection of directivity or gain thereof requires an adequate procedure and smart post-processing. In this paper, a new method is proposed for estimating the directivity of radiating devices in a reverberation chamber (RC). The method is based on the Rician K-factor whose estimation in an RC benefits from recent improvements. Directivity estimation relies on the accurate determination of the K-factor with respect to a reference antenna. Good agreement is reported with measurements carried out in near-field anechoic chamber (AC) and using a near-field to far-field transformation.

A canonical UTD solution for electromagnetic scattering by an electrically large impedance circular cylinder illuminated by an obliquely incident plane wave

A uniform geometrical theory of diffraction (UTD) solution is developed for the canonical problem of the electromagnetic (EM) scattering by an electrically large circular cylinder with a uniform impedance boundary condition (IBC), when it is illuminated by an obliquely incident high frequency plane wave. A solution to this canonical problem is first constructed in terms of an exact formulation involving a radially propagating eigenfunction expansion. The latter is converted into a circumferentially propagating eigenfunction expansion suited for large cylinders, via the Watson transform, which is expressed as an integral that is subsequently evaluated asymptotically, for high frequencies, in a uniform manner. The resulting solution is then expressed in the desired UTD ray form. This solution is uniform in the sense that it has the important property that it remains continuous across the transition region on either side of the surface shadow boundary. Outside the shadow boundary transition region it recovers the purely ray optical incident and reflected ray fields on the deep lit side of the shadow boundary and to the modal surface diffracted ray fields on the deep shadow side. The scattered field is seen to have a cross-polarized component due to the coupling between the TEz and TMz waves (where z is the cylinder axis) resulting from the IBC. Such cross-polarization vanishes for normal incidence on the cylinder, and also in the deep lit region for oblique incidence where it properly reduces to the geometrical optics (GO) or ray optical solution. This UTD solution is shown to be very accurate by a numerical comparison with an exact reference solution.

Laser shock processing: an emerging technique for the improvement of fatigue life and surface properties of high reliability metallic components

•Introduction •Process Experimental Setup •Experimental Procedure •Experimental Results for Al2024 - T351, Ti6Al4V and AISI 316L - Surface Roughness and Compactation - Residual stresses - Tensile Strength - Fatigue Life •Discussion and Outlook - Prospects for technological applications of LSP

Surface Impedance Characterization for UTD Based Solution with IBC for Surface Fields on a Dielectric-Coated PEC Circular Cylinder

A novel formulation for the surface impedance characterization is introduced for the canonical problem of surface fields on a perfect electric conductor (PEC) circular cylinder with a dielectric coating due to a electric current source using the Uniform Theory of Diffraction (UTD) with an Impedance Boundary Condition (IBC). The approach is based on a TE/TM assumption of the surface fields from the original problem. Where this surface impedance fails, an optimization is performed to minimize the error in the SD Green?s function between the original problem and the equivalent one with the IBC. This new approach requires small changes in the available UTD based solution with IBC to include the geodesic ray angle and length dependence in the surface impedance formulas. This asymptotic method, accurate for large separations between source and observer points, in combination with spectral domain (SD) Green?s functions for multidielectric coatings leads to a new hybrid SD-UTD with IBC to calculate mutual coupling among microstrip patches on a multilayer dielectric-coated PEC circular cylinder. Results are compared with the eigenfunction solution in SD, where a very good agreement is met.