V-substituted In2S3: an intermediate band material with photocatalytic activity in the whole visible light range

We proposed in our previous work V-substituted In2S3 as an intermediate band (IB) material able to enhance the efficiency of photovoltaic cells by combining two photons to achieve a higher energy electron excitation, much like natural photosynthesis. Here this hyper-doped material is tested in a photocatalytic reaction using wavelength-controlled light. The results evidence its ability to use photons with wavelengths of up to 750 nm, i.e. with energy significantly lower than the bandgap (=2.0 eV) of non-substituted In2S3, driving with them the photocatalytic reaction at rates comparable to those of non-substituted In2S3 in its photoactivity range (λ ≤ 650 nm). Photoluminescence spectra evidence that the same bandgap excitation as in V-free In2S3 occurs in V-substituted In2S3 upon illumination with photons in the same sub-bandgap energy range which is effective in photocatalysis, and its linear dependence on light intensity proves that this is not due to a nonlinear optical property. This evidences for the first time that a two-photon process can be active in photocatalysis in a single-phase material. Quantum calculations using GW-type many-body perturbation theory suggest that the new band introduced in the In2S3 gap by V insertion is located closer to the conduction band than to the valence band, so that hot carriers produced by the two-photon process would be of electron type; they also show that the absorption coefficients of both transitions involving the IB are of significant and similar magnitude. The results imply that V-substituted In2S3, besides being photocatalytically active in the whole visible light range (a property which could be used for the production of solar fuels), could make possible photovoltaic cells of improved efficiency.

New strategies in laser processing of TCOs for light management improvement in thin-film silicon solar cells

Light confinement strategies play a crucial role in the performance of thin-film (TF) silicon solar cells. One way to reduce the optical losses is the texturing of the transparent conductive oxide (TCO) that acts as the front contact. Other losses arise from the mismatch between the incident light spectrum and the spectral properties of the absorbent material that imply that low energy photons (below the bandgap value) are not absorbed, and therefore can not generate photocurrent. Up-conversion techniques, in which two sub-bandgap photons are combined to give one photon with a better matching with the bandgap, were proposed to overcome this problem. In particular, this work studies two strategies to improve light management in thin film silicon solar cells using laser technology. The first one addresses the problem of TCO surface texturing using fully commercial fast and ultrafast solid state laser sources. Aluminum doped Zinc Oxide (AZO) samples were laser processed and the results were optically evaluated by measuring the haze factor of the treated samples. As a second strategy, laser annealing experiments of TCOs doped with rare earth ions are presented as a potential process to produce layers with up-conversion properties, opening the possibility of its potential use in high efficiency solar cells.

Four-Band Hamiltonian for fast calculations in intermediate-band solar cells

The 8-dimensional Luttinger–Kohn–Pikus–Bir Hamiltonian matrix may be made up of four 4-dimensional blocks. A 4-band Hamiltonian is presented, obtained from making the non-diagonal blocks zero. The parameters of the new Hamiltonian are adjusted to fit the calculated effective masses and strained QD bandgap with the measured ones. The 4-dimensional Hamiltonian thus obtained agrees well with measured quantum efficiency of a quantum dot intermediate band solar cell and the full absorption spectrum can be calculated in about two hours using Mathematica© and a notebook. This is a hundred times faster than with the commonly-used 8-band Hamiltonian and is considered suitable for helping design engineers in the development of nanostructured solar cells.

Photoexcited-induced sensitivity of InGaAs surface QDs to environment

A detailed analysis of the impact of illumination on the electrical response of In0.5Ga0.5As surface nanostructures is carried out as a function of different relative humidity conditions. The importance of the surface-to-volume ratio for sensing applications is once more highlighted. From dark-to-photo conditions, the sheet resistance (SR) of a three-dimensional In0.5Ga0.5As nanostructure decays two orders of magnitude compared with that of a two-dimensional nanostructure. The electrical response is found to be vulnerable to the energy of the incident light and the external conditions. Illuminating with high energy light translates into an SR reduction of one order of magnitude under humid atmospheres, whereas it remains nearly unchanged under dry environments. Conversely, lighting with energy below the bulk energy bandgap, shows a negligible effect on the electrical properties regardless the local moisture. Both illumination and humidity are therefore needed for sensing. Photoexcited carriers can only contribute to conductivity if surface states are inactive due to water physisorption. The strong dependence of the electrical response on the environment makes these nanostructures very suitable for the development of highly sensitive and efficient sensing devices.

Demonstration of the operation principles of intermediate band solar cells at room temperature

In this work we report, for the first time at room temperature, experimental results that prove, simultaneously in the same device, the two main physical principles involved in the operation of intermediate band solar cells: (1) the production of sub-bandgap photocurrent by two optical transitions through the intermediate band; (2) the generation of an output voltage which is not limited by the photon energy absorption threshold. These principles, which had always required cryogenic temperatures to be evidenced all together, are now demonstrated at room temperature on an intermediate band solar cell based on InAs quantum dots with Al0.3Ga0.7As barriers.

Propiedades ópticas y estructurales de nanoestructuras de Zn(Cd)(Mg)O

En la presente tesis doctoral se ha realizado un estudio utilizando diferentes técnicas de crecimiento (RPE-MOCVD y spray pyrolysis) y estructuras (nanohilos, pozos y puntos cuánticos y capas) con el objetivo de desarrollar dispositivos que cubran desde el rango visible hasta el ultravioleta. Es por esta razón por la que se han elegido materiales basados en ZnO, debido a la posibilidades que estos ofrecen para variar su bandgap en un amplio rango de energías. Prueba de ello es que en este estudio se ha conseguido cubrir un rango espectral desde 1.86 hasta 4.11 eV, estudiandose además fenómenos físicos como son la difusión e incorporaci ón de la aleación o la adsorción de gases en la super_cie, lo que ha permitido la fabricación de diferentes fotodetectores de gran sensibilidad. Por todo ello, los resultados obtenidos en esta tesis suponen una gran contribución al conocimiento de las propiedades físicas de las aleaciones de Zn(Cd)O y Zn(Mg)O para potenciales aplicaciónes en dispositivos que operen en el rango visible y ultravioleta del espectro, respectivamente. En esta memoria se da en primer lugar una visión de las propiedades de materiales basados en ZnO, entrando en detalle en una de las ventajas que este presenta, la facilidad que tiene este material para formar nanoestructuras. En el capítulo 3 se dan los conceptos teóricos necesarios para comprender las propiedades ópticas de este tipo de materiales, mostrando también los resultados más reseñables obtenidos en ZnO. En los capítulos referentes a los resultados se pueden diferenciar dos grandes bloques. En el primer bloque de resultados se han analizado nanohilos y pozos cuánticos de Zn(Cd)O crecidos por la técnica de RPE-MOCVD (Capítulos 4 y 5). En el segundo se expondrá el estudio realizado sobre capas y puntos cuánticos de Zn(Mg)O crecidos por la técnica spray pyrolysis como se describe en mayor detalle a continuación. Nanohilos y pozos cuánticos de Zn(Cd)O crecidos por RPE-MOCVD Teóricamente aleando el ZnO con CdO es posible disminuir el valor del band- gap desde 3.37 eV hasta 0.95 eV, cubriendo por completo el espectro visible. El desarrollo del ternario Zn(Cd)O permitiría la fabricación de heteroestructuras y pozos cuánticos, muy importantes en el desarrollo de dispositivos optoelectrónicos que cubran la parte visible del espectro. Sin embargo, la diferencia de estructura cristalina entre estos dos materiales junto a la baja solubilidad del Cd y su alta presión de vapor, di_culta la obtención de material de alta calidad cristalina con alto contenido en Cd. En esta tesis doctoral se ha realizado una completa caracterización óptica y estructural de nanohilos de Zn(Cd)O credidos por la técnica de RPE-MOCVD. Estos nanohilos tinene unas longitudes comprendidas entre 1 y 3 _m y diámetros entre 100 y 200 nm. La concentración máxima introducida de Cd en estas estructuras ha sido de hasta un 54% manteniendo la estructura wurtzita del ZnO, siendo este el mayor contenido de Cd introducido hasta la fecha en nanostructuras basada en ZnO. Este hecho se traduce en una variación de la energía de emisión entre 3.31 y 1.86 eV con el aumento en Cd. El uso de diferentes técnicas de alta resoluci ón de caracterización estructural ha permitido demostrar la presencia de una sola fase estructural wurtzita sin observarse ningún indicio de separación de fases ni acumulación de Cd a lo largo del nanohilo para todos los contenidos de Cd. Con el propósito de fabricar dispositivos en nanohilos individuales, parte de esta tesis doctoral ha estado dedicada a estudiar el impacto que el recocido térmico tiene en las propiedades ópticas y eléctricas de nanohilos de Zn(Cd)O. El recocido térmico es un proceso clave en la optimización de dispositivos, ya sea para la obtenci ón de contactos óhmicos, reducción de defectos o difusión de dopantes por ejemplo. En este estudio se ha observado una mejora muy signi_cativa de las propiedades de emisión de los nanohilos cuando estos eran recocidos a temperaturas mayores que la de crecimiento (300 oC). En las muestras con Cd se ha observado además que el recocido también produce un desplazamiento de la emisión hacia mayores energías debido a una reducción homogénea del contenido de Cd. Medidas de fotoluminiscencia con resolución temporal muestran el impacto que tiene la localización del excitón en las _uctuaciones de potencial, debidas a una distribución estadística del Cd, en la dinámica de los portadores. Comparando el tiempo de vida de los portadores entre los nanohilos recocidos y sin recocer se ha observado un aumento de este parámetro en las estructuras recocidas. Este aumento es fundamentalmente debido a una reducción de centros de recombinación no radiativa asociados a defectos presentes a lo largo del nanohilo. Además, se ha estudiado la evolución de los tiempos de vida de los portadores en función de la temperatura, registrándose una menor estabilidad con la temperatura de los tiempos de vida en las muestras recocidas. Este resultado sugiere que el recocido térmico consigue reducir parte del desorden de la aleación en la estructura. Tras haber caracterizados los nanohilos se desarrollaron una serie de procesa dos para la fabricación de dispositivos basados en nanohilos individuales. Se fabricaron en concreto fotodetectores sensibles al UV, en los que se observó también la alta sensibilidad que muestran a la adsorción de gases en la super_cie, incrementada por la gran relación super_cie/volúmen característica de las nanoestructuras. Estos procesos de adsorción observados tienen un impacto directo sobre las propiedades ópticas y electricas de los dispositivos como se ha demostrado. Por ello que en esta tesis se hayan estudiado en detalle este tipo de procesos, ideando maneras para tener un mayor control sobre ellos. Finalmente se crecieron estructuras de pozos cuántico de ZnCdO/ZnO en nanohilos con contenidos de Cd nominales de 54 %. Las medidas ópticas realizadas mostraron como al aumentar la anchura del pozo de 0.7 a 10 nm, la emisión relacionada con el pozo se desplazaba entre 3.30 y 1.97 eV. Este gran desplazamiento representa el mayor obtenido hasta la fecha en pozos cuánticos de ZnCdO/ZnO. Sin embargo, al caracterizar estructuralmente estas muestras se observó la presencia de procesos de difusión de Cd entre el pozo y la barrera. Como se ha podido medir, este tipo de procesos reducen sustancialmente la concentración de Cd en el pozo al difundirse parte a la barrera. cambiando completamente la estructura de bandas nominal de estas estructuras. Este estudio demuestra la importancia del impacto de los procesos de difusión en la interpretación de los efectos de con_namiento cuántico para este tipo de estructuras. Capas y puntos cuánticos de Zn(Mg)O crecidos por spray pyrolysis La técnica de spray pyrolysis, debido a su simplicidad, bajo coste y capacidad de crecer sobre grandes áreas conservando una alta calidad cristalina presenta un gran interés en la comunidad cientí_ca para el potencial desarrollo de dispositivos comerciales. En esta tesis se ha estudiado las propiedades ópticas y eléctricas de capas y puntos cuánticos de Zn(Mg)O crecidos por esta técnica. Al contrario que pasa con el Cd, al introducir Mg en la estructura wurtzita de ZnO se consigue aumentar el bandgap del semiconductor. Sin embargo, al igual que pasa con el CdO, la diferencia de estructura cristalina entre el ZnO y el MgO limita la cantidad de Mg que se puede incorporar, haciendo que para una cierta concentración de Mg aparezcan el fenómeno de separación de fases. En esta tesis se ha conseguido incorporar hasta un contenido de Mg del 35% en la estructura wurtzita del ZnO utilizando la técnica de spray pyrolysis, resultado que representa la mayor concentración de Mg publicada hasta la fecha. Este hecho ha posibilitado variar la energía del borde de absorción desde 3.30 a 4.11 eV. En estas capas se ha realizado una completa caracterización óptica observándose una diferencia entre las energías del borde de absorción y del máximo de emisión creciente con el contenido en Mg. Esta diferencia, conocida como desplazamiento de Stokes, es debida en parte a la presencia de _uctuaciones de potencial producidas por un desorden estadístico de la aleación. Se han fabricado fotodetectores MSM de alta calidad utilizando las capas de Zn(Mg)O previamente caracterizadas, observándose un desplazamiento del borde de absorción con el aumento en Mg desde 3.32 a 4.02 eV. Estos dispositivos muestran altos valores de responsividad (10-103 A/W) y altos contrastes entre la responsividad bajo iluminación y oscuridad (10-107). Estos resultados son en parte debidos a la presencia de mecanismos de ganancia y una reducción de la corriente de oscuridad en las muestras con alto contenido de Mg. Utilizando esta misma técnica de crecimiento se han crecido puntos de Zn(Mg)O con concentraciones nominales de Mg entre 0 y 100 %, con dimensiones medias entre 4 y 6 nm. Las medidas estructurales realizadas muestran que hasta un valor de Mg de 45 %, los puntos están compuestos por una única fase estructural, wurtzita. A partir de esa concentración de Mg aparece una fase cúbica en los puntos, coexistiendo con la fase hexagonal hasta una concentración nominales del 85 %. Para concentraciones mayores de Mg, los puntos muestran una única fase estructural cúbica. Medidas de absorción realizadas en estos puntos de Zn(Mg)O muestran un desplazamiento del borde de absorción entre 3.33 y 3.55 eV cuando la concentraci ón de Mg en los puntos aumenta hasta el 40 %. Este desplazamiento observado es debido solamente a la fase wurtzita del Zn(Mg)O donde se incorpora el Mg. ABSTRACT This PhD theis presents a study using di_erent growth techniques (RPEMOCVD and spray pyrolysis) and structures (nanowires, quantum dots and wells and layers) in order to develop devices that extend from the visible to the ultraviolet range. For this reason ZnO based materials have been choosen, because they o_er the possibility to tunne the bandgap in this energy range. Proof of this is that this study has managed to cover a spectral range from 1.86 to 4.11 eV, also being studied physical phenomena such as di_usion and incorporation of alloy or adsorption of gases on the surface, allowing the develop di_erent highly sensitive photodetectors. Therefore, the results obtained in this thesis are a great contribution two large blockso the knowledge of the physical properties of alloys Zn(Cd)O and Zn(Mg)O for potential applications in devices that operate in the visible and ultraviolet range, respectively. In the _rst chapter, the general properties of ZnO-based materials are presented, showing the facilities that these kind of materials o_er to obtain di_erent nanoestructures. In Chapter 3, optical theoretical concepts are given to understand the optical properties of these materials, also showing the most signi_cant results of ZnO. In the chapters related with the results, two blocks could be distinguish. In the _rst one, Zn(Cd)O nanowires and quantum wells grown by RPE-MOCVD have been analyzed (Chapters 4 and 5). The second block of results shows the study performed in Zn(Mg)O _lms and quantum dots grown by spray pyrolysis. Zn(Cd)O nanowires and quantum wells grown by RPE-MOCVD In summary, the results of the PhD thesis are a great contribution to the knowledge of the physical properties of Zn(Cd)O and Zn(Mg)O alloys and their application for high performance devices operating in the visible and UV ranges, respectively. The performance of the device is still limited due to alloy solubility and p-doping stability, which opens a door for future research in this _eld. Theoretically, annealing ZnO with CdO allows to reduce the bandgap from 3.37 to 0.95 eV, covering the whole visible spectrum. The development of ZnCdO alloys allows the fabrication of heterostructures and quantum wells, necessary for the development of high performance optoelectronic devices. However, the di_erent crystal structures between CdO and ZnO and the low solubility of Cd and its high vapor pressure, hinders the growth of ZnCdO alloys with high Cd contents. In this PhD thesis Zn(Cd)O nanowires have been optically and structurally characterized, obtaining a maximum Cd content of 54% while maintaining their wurtzite structure. This Cd content, which allows lowering the bandgap down to 1.86 eV, is the highest concentration ever reported in nanostructures based on ZnO. The combination of optical and structural characterization techniques used during this thesis has allowed the demonstration of the presence of a single wurtzite structure, without observing any indication of phase separation or Cd accumulation along the nanowire. Annealing processes are essential in the fabrication of optoelectronic devices. For this reason, a complete study of the annealing e_ects in the optical and electrical properties of Zn(Cd)O nanowires has been performed. In the _rst place, annealing nanowires at higher temperatures than their growth temperature (300 oC) allows a signi_cant improvement of their emission properties. However, in the samples that contain Cd a shift in the emission towards higher energies has been observed due to a homogeneous reduction of the Cd content in the nanowires. Time resolved photoluminescence measurements show the impact of the exciton localization in the potential _uctuations due to a statistical alloy disorder. An increase in the carrier lifetime has been obtained for the annealed nanowires. This increase is mainly due to the reduction of non-radiative recombination centers associated with the defects present in the material. Furthermore, temperature dependent time resolved photoluminescence measurements suggest a reduction of the alloy disorder in the annealed samples. In this thesis, single nanowire photodetectors with a high responsivity in the UV range have been demonstrated. Due to the high surface/volume ratio, these structures are very sensitive to gas adsorption at the surface, which largely de_nes the optical and electrical properties of the material and, therefore, of the device. With the aim of obtaining time stable devices, the dynamic adsorption-desorption processes have been studied, developing di_erent approaches that allow a higher control over them. Finally, ZnCdO/ZnO quantum wells have been grown with a nominal Cd concentration of 54% inside the well. The performed optical measurements show that increasing the well width from 0.7 to 10 nm, shifts the emission related with the well from 3.30 to 1.97 eV. This result represents the highest shift reported in the literature. However, a detailed structural characterization shows the presence of di_usion phenomena which substantially reduce the concentration of Cd in the well, while increasing it in the barrier. This type of phenomena should be considered when ac curately interpretating the quantum con_nement e_ects in Zn(Cd)O/ZnO quantum wells. Theoretically, annealing ZnO with CdO allows to decrease the bandgap from 3.37 to 0.95 eV, covering the whole visible spectrum. Zn(Mg)O _lms and quantum dots grown by spray pyrolysis Due to its simplicity, low-cost and capacity to grow over large areas conserving a high crystal quality, spray pyrolysis technique presents a great interest in the scienti_c community for developing comercial devices. In this thesis, a complete study of the optical and structural properties of Zn(Mg)O _lms and quantum dots grown by spray pyrolysis has been performed. Contrary to Zn(Cd)O alloys, when introducing Mg in the ZnO wurtzite structure an increase in the bandgap in obtained. Once again, the di_erence in the crystal structure of ZnO and MgO limits the amount of Mg that can be introduced before phase separation appears. In this PhD thesis, a maximum Mg content of 35% has been incorporated in the wurtzite structure using spray pyrolysis. This variation in the Mg content translates into an increase of the absorption edge from 3.30 to 4.11 eV. Up to this date, this result represents the highest Mg content introduced by spray pyrolysis in a ZnO wurzite structure reported in the literature. The comparison of the emission and absorption spectra shows the presence of an increasing Stokes shift with Mg content. This phenomenon is partialy related with the presence of potential _uctuations due to an statistic alloy disorder. MSM photodetectors have been processed on previously characterized Zn(Mg)O _lms. These devices have shown a shift in the absorption edge from 3.32 to 4.02 eV with the increase in Mg content, high responsivity values (10-103 A/W) and high contrast ratios between illuminated and dark responsivities (10-107). These values are explained by the presence of a gain mechanism and a reduction of dark current in the ZnMgO samples. Zn(Mg)O quantum dots have also been grown using spray pyrolysis with Mg concentrations between 0 and 100% and with average widths ranging 4 to 6 nm. Structural measurements show that at a Mg concentration of 45% the cubic phase appears, coexisting with the hexagonal phase up to an 85% concentration of Mg content. From 85% onwards the quantum dots show only the cubic phase. Absorption measurements performed in these structures reveal a shift in the absorption edge from 3.33 to 3.55 eV when the Mg content increases up to 40 %.

Effect of Sb on the quantum efficiency of GaInP solar cells

The energy bandgap of GaInP solar cells can be tuned by modifying the degree of order of the alloy. In this study, we employed Sb to increase the energy bandgap of the GaInP and analyzed its impact on the performance of GaInP solar cells. An effective change in the cutoff wavelength of the external quantum efficiency of GaInP solar cells and an effective increase of 50 mV in the open-circuit voltage of GaInP/Ga(In)As/Ge triple junction solar cells were obtained with the use of Sb. Copyright © 2016 John Wiley & Sons, Ltd.

Ultra high temperature latent heat energy storage and thermophotovoltaic energy conversion

A conceptual energy storage system design that utilizes ultra high temperature phase change materials is presented. In this system, the energy is stored in the form of latent heat and converted to electricity upon demand by TPV (thermophotovoltaic) cells. Silicon is considered in this study as PCM (phase change material) due to its extremely high latent heat (1800 J/g or 500 Wh/kg), melting point (1410 C), thermal conductivity (~25 W/mK), low cost (less than $2/kg or $4/kWh) and abundance on earth. The proposed system enables an enormous thermal energy storage density of ~1 MWh/m3, which is 10e20 times higher than that of lead-acid batteries, 2e6 times than that of Li-ion batteries and 5e10 times than that of the current state of the art LHTES systems utilized in CSP (concentrated solar power) applications. The discharge efficiency of the system is ultimately determined by the TPV converter, which theoretically can exceed 50%. However, realistic discharge efficiencies utilizing single junction TPV cells are in the range of 20e45%, depending on the semiconductor bandgap and quality, and the photon recycling efficiency. This concept has the potential to achieve output electric energy densities in the range of 200-450 kWhe/m3, which is comparable to the best performing state of the art Lithium-ion batteries.

Optical properties of ZnMgO films grown by spray pyrolysis and their application to UV photodetection

This work presents a comprehensive optical characterization of Zn1−xMgxO thin films grown by spray pyrolysis (SP). Absorption measurements show the high potential of this technique to tune the bandgap from 3.30 to 4.11 eV by changing the Mg acetate content in the precursor solution, leading to a change of the Mg-content ranging from 0 up to 35%, as measured by transmission electron microscopy-energy dispersive x-ray spectroscopy. The optical emission of the films obtained by cathodoluminescence and photoluminescence spectroscopy shows a blue shift of the peak position from 3.26 to 3.89 eV with increasing Mg incorporation, with a clear excitonic contribution even at high Mg contents. The linewidth broadening of the absorption and emission spectra as well as the magnitude of the observed Stokes shift are found to significantly increase with the Mg content. This is shown to be related to both potential fluctuations induced by pure statistical alloy disorder and the presence of a tail of band states, the latter dominating for medium Mg contents. Finally, metal–semiconductor–metal photodiodes were fabricated showing a high sensitivity and a blue shift in the cut-off energy from 3.32 to 4.02 eV, i.e., down to 308 nm. The photodiodes present large UV/dark contrast ratios (102 − 107), indicating the viability of SP as a growth technique to fabricate low cost (Zn, Mg)O-based UV photodetectors reaching short wavelengths.

Heterojunction Band Offset Limitations on Open-Circuit Voltage in p-ZnTe/n-ZnSe Solar Cells

Limitations on the open-circuit voltage of p-ZnTe/n-ZnSe heterojunction solar cells are studied via current-voltage (I-V) measurements under solar concentration and at variable temperature. The open-circuit voltage reaches a maximum value of 1.95 V at 77 K and 199 suns. The open-circuit voltage shows good agreement with the calculated built-in potential of 2.00 V at 77 K. These results suggest that the open-circuit voltage is limited by heterojunction band offsets associated with the type-II heterojunction band lineup, rather than the bandgap energy of the ZnTe absorber material.

Three-terminal heterojunction bipolar transistor solar cell for high-efficiency photovoltaic conversion

Here we propose, for the first time, a solar cell characterized by a semiconductor transistor structure (n/p/n or p/n/p) where the base-emitter junction is made of a high-bandgap semiconductor and the collector is made of a low-bandgap semiconductor. We calculate its detailed-balance efficiency limit and prove that it is the same one than that of a double-junction solar cell. The practical importance of this result relies on the simplicity of the structure that reduces the number of layers that are required to match the limiting efficiency of dual-junction solar cells without using tunnel junctions. The device naturally emerges as a three-terminal solar cell and can also be used as building block of multijunction solar cells with an increased number of junctions.

Why can't I measure the external quantum efficiency of the Ge subcell of my multijunction solar cell?

The measurement of the external quantum efficiency (EQE) of low bandgap subcells in a multijunction solar cell can be sometimes problematic. In particular, this paper describes a set of cases where the EQE of a Ge subcell in a conventional GaInP/GaInAs/Ge triple-junction solar cell cannot be fully measured. We describe the way to identify each case by tracing the I-V curve under the same light-bias conditions applied for the EQE measurement, together with the strategies that could be implemented to attain the best possible measurement of the EQE of the Ge subcell.