Temperature Sensor Placement Including Routing Overhead and Sampling Inaccuracies

Dynamic thermal management techniques require a collection of on-chip thermal sensors that imply a significant area and power overhead. Finding the optimum number of temperature monitors and their location on the chip surface to optimize accuracy is an NP-hard problem. In this work we improve the modeling of the problem by including area, power and networking constraints along with the consideration of three inaccuracy terms: spatial errors, sampling rate errors and monitor-inherent errors. The problem is solved by the simulated annealing algorithm. We apply the algorithm to a test case employing three different types of monitors to highlight the importance of the different metrics. Finally we present a case study of the Alpha 21364 processor under two different constraint scenarios.

Power management techniques in an FPGA-Based WSN node for high performance application

In this work, the power management techniques implemented in a high-performance node for Wireless Sensor Networks (WSN) based on a RAM-based FPGA are presented. This new node custom architecture is intended for high-end WSN applications that include complex sensor management like video cameras, high compute demanding tasks such as image encoding or robust encryption, and/or higher data bandwidth needs. In the case of these complex processing tasks, yet maintaining low power design requirements, it can be shown that the combination of different techniques such as extensive HW algorithm mapping, smart management of power islands to selectively switch on and off components, smart and low-energy partial reconfiguration, an adequate set of save energy modes and wake up options, all combined, may yield energy results that may compete and improve energy usage of typical low power microcontrollers used in many WSN node architectures. Actually, results show that higher complexity tasks are in favor of HW based platforms, while the flexibility achieved by dynamic and partial reconfiguration techniques could be comparable to SW based solutions.

Development of Embedded Linux Applications Using ZedBoard

The purpose of this document is to create a modest integration guide for embedding a Linux Operating System on ZedBoard development platform, based on Xilinx’s Zynq-7000 All Programmable System on Chip which contains a dual core ARM Cortex-A9 and a 7 Series FPGA Artix-7. The integration process has been structured in four chapters according to the logic generation of the different parts that compose the embedded system. With the intention of automating the generation process of a complete Linux distribution specific for ZedBoard platform, BuildRoot development platform it is used. Once the embedding process finished, it was decided to add to the system the required functionalities for adding support for IEEE1588 Standard for Precision Clock Synchronization Protocol for Networked Measurement and Control Systems, through a user space Linux program which implements the protocol. That PTP user space implementation program has been cross-compiled, executed on target and tested for evaluating the functionalities added. RESUMEN El propósito de este documento es crear una modesta guía de integración de un sistema operativo Linux para la plataforma de desarrollo ZedBoard, basada en un System on Chip del fabricante Xilinx llamado Zynq-7000. Este System on Chip está compuesto por un procesador de doble núcleo ARM Cortex-A9 y una FPGA de la Serie 7 equiparable a una Artix-7. El proceso de integración se ha estructurado en cuatro grandes capítulos que se rigen según el orden lógico de generación de las distintas partes por las que el sistema empotrado está compuesto. Con el ánimo de automatizar el proceso de creación de una distribución de Linux específica para la plataforma ZedBoard, se ha utilizado la plataforma de desarrollo BuildRoot. Una vez terminado el proceso de integración del sistema empotrado, se procedió a dar dotar al sistema de las funcionalidades necesarias para dar soporte al estándar de sincronización de relojes en redes de área local, PTP IEEE1588, a través de una implementación del mismo en un programa de lado de usuario el cual ha sido compilado, ejecutado y testeado para evaluar el correcto funcionamiento de las funcionalidades añadidas.

Sintetizador analógico en Arduino

Este proyecto consiste en el diseño y construcción de un sintetizador basado en el chip 6581 Sound Interface Device (SID). Este chip era el encargado de la generación de sonido en el Commodore 64, ordenador personal comercializado en 1982, y fue el primer sintetizador complejo construido para ordenador. El chip en cuestión es un sintetizador de tres voces, cada una de ellas capaz de generar cuatro diferentes formas de onda. Cada voz tiene control independiente de varios parámetros, permitiendo una relativamente amplia variedad de sonidos y efectos, muy útil para su uso en videojuegos. Además está dotado de un filtro programable para conseguir distintos timbres mediante síntesis sustractiva. El sintetizador se ha construido sobre Arduino, una plataforma de electrónica abierta concebida para la creación de prototipos, consistente en una placa de circuito impreso con un microcontrolador, programable desde un PC para que realice múltiples funciones (desde encender LEDs hasta controlar servomecanismos en robótica, procesado y transmisión de datos, etc.). El sintetizador es controlable vía MIDI, por ejemplo, desde un teclado de piano. A través de MIDI recibe información tal como qué notas debe tocar, o los valores de los parámetros del SID que modifican las propiedades del sonido. Además, toda esa información también la puede recibir de un PC mediante una conexión USB. Se han construido dos versiones del sintetizador: una versión “hardware”, que utiliza el SID para la generación de sonido, y otra “software”, que reemplaza el SID por un emulador, es decir, un programa que se comporta (en la medida de lo posible) de la misma manera que el SID. El emulador se ha implementado en un microcontrolador Atmega 168 de Atmel, el mismo que utiliza Arduino. ABSTRACT. This project consists on design and construction of a synthesizer which is based on chip 6581 Sound Interface Device (SID). This chip was used for sound generation on the Commodore 64, a home computer presented in 1982, and it was the first complex synthesizer built for computers. The chip is a three-voice synthesizer, each voice capable of generating four different waveforms. Each voice has independent control of several parameters, allowing a relatively wide variety of sounds and effects, very useful for its use on videogames. It also includes a programmable filter, allowing more timbre control via subtractive synthesis. The synthesizer has been built on Arduino, an open-source electronics prototyping platform that consists on a printed circuit board with a microcontroller, which is programmable with a computer to do several functions (lighting LEDs, controlling servomechanisms on robotics, data processing or transmission, etc.). The synthesizer is controlled via MIDI, in example, from a piano-type keyboard. It receives from MIDI information such as the notes that should be played or SID’s parameter values that modify the sound. It also can receive that information from a PC via USB connection. Two versions of the synthesizer have been built: a hardware one that uses the SID chip for sound generation, and a software one that replaces SID by an emulator, it is, a program that behaves (as far as possible) in the same way the SID would. The emulator is implemented on an Atmel’s Atmega 168 microcontroller, the same one that is used on Arduino.

Sistema de telemetría para un vehículo de fórmula S.A.E.

En este proyecto, se ha desarrollado una aplicación electrónica para un coche de competición, en concreto para la fórmula SAE (Society of Automotive Engineers), una competición universitaria en la que cada equipo, formado por estudiantes, debe diseñar, construir y probar un prototipo basándose en una serie de reglas. El objetivo final de la competición es proporcionar a los estudiantes el conocimiento práctico necesario para su futura labor profesional, del cual se pensaba que los estudiantes adolecían al acabar sus estudios universitarios cuando se creó esta competición. La aplicación desarrollada en este proyecto consiste en un sistema de telemetría, utilizado para transmitir los datos proporcionados por los sensores del vehículo a través de un sistema de radiofrecuencia, de manera que se pueda estudiar el comportamiento del coche durante los ensayos a la vez que el coche está rodando y así no depender de un sistema de adquisición de datos del que había que descargarse la información una vez finalizada la sesión de ensayo, como había que hacer hasta el momento. Para la implementación del proyecto, se ha utilizado un kit de desarrollo (Xbee Pro 868) que incluye dos módulos de radio, dos placas de desarrollo, dos cables USB y una antena, el cual ha permitido desarrollar la parte de radio del proyecto. Para transmitir los datos proporcionados por la centralita del vehículo, la cual recoge la información de todos los sensores presentes en el vehículo, se han desarrollado dos placas de circuito impreso. La primera de ellas tiene como elemento principal un microprocesador PIC de la marca Microchip (PIC24HJ64GP502), que recoge los datos proporcionados por la centralita del vehículo a través de su bus CAN de comunicaciones. La segunda placa de circuito impreso tiene como elemento fundamental el transmisor de radio. Dicho transmisor está conectado al microprocesador de la otra placa a través de línea serie. Como receptor de radio se ha utilizado una de las placas de prueba que integraba el kit de desarrollo Xbee Pro 868, la cual recoge los datos que han sido enviados vía radio y los manda a su vez a través de USB a un ordenador donde son monitorizados. Hasta aquí la parte hardware del sistema. En cuanto a la parte software, ha habido que desarrollar una aplicación en lenguaje C, que ejecuta el microprocesador PIC, que se encarga de recoger los datos enviados por la centralita a través del bus CAN (Controller Area Network) y transmitirlos a través de línea serie al chip de radio. Por último, para la monitorización de los datos se han desarrollado dos aplicaciones en LabVIEW, una que recoge los datos a través de USB, los muestra en pantalla y los guarda en un fichero y otra que lee los datos del fichero y los representa gráficamente para permitir un estudio más detallado del comportamiento del vehículo. ABSTRACT In this project, an electronic application has been developed for a race car – Formula SAE car-. Formula SAE is a university championship in which each team, made up of students, should design, construct and test a prototype within certain rules. The final goal of the competition is to enhance the practical knowledge of the students, which was thougth to be poor at the time the competition was created. The application developed in this project consists of a telemetry system, employed to transmit the data provided by the car’s sensors through a radio frequency system, so that it could be possible to study the behaviour of the vehicle during tests and do not depend on a datalogger system as it occurred until now. To carry out the radio module of the project, a Xbee Pro 868 development kit has been used, which includes two radio modules, two development boards, two USB cables and an antenna. To transmit the data provided by the ECU (Engine Control Unit) of the vehicle, which receives information from all the sensors the vehicle has, two printed circuit boards have been built. One of them has a PIC microprocessor of Microchip (PIC24HJ64GP502) which receives the data coming from CAN bus of the ECU. Tha main element of the other printed circuit board is the radio transmitter. This chip receives the data from the microprocessor through its serial line. The development board of the Xbee Pro 868 has been used as receiver. When data arrives to the receiver, it transmits them to a computer through USB where the data are displayed. All this composes the hardware of the system. Regarding the software, a C coded application has been developed. This application is executed by the microprocessor and its function is to receive the data from the bus CAN (Controller Area Network) and send them to the radio transmitter through the microprocessor’s serial line. To show the data on the computer, two LabVIEW applications has been developed. The first one receives the data through the USB port, displays them on the screen and save them to a file and the second one reads the data from the file while represents them graphically to allow studying the behaviour of the car on track.

Las nuevas tecnologías de la información

En 1947 sólo había un ordenador y los expertos opinaban que se necesitarían como mucho 6 o 7 más para llevar todos los asuntos de Estados Unidos. Hoy, 50 años después, puede haber en el mundo unos 300 millones de ordenadores personales y, según mis estimaciones, más de 10.000 millones de microprocesadores. La velocidad de cálculo de estos microprocesadores, del tamaño de un chip, y cuyo contenido y estructura son solamente visibles mediante un microscopio electrónico, se acerca ya a los 200 millones de instrucciones por segundo.

A self-timed multipurpose delay sensor for field programmable gate arrays (FPGAs)

This paper presents a novel self-timed multi-purpose sensor especially conceived for Field Programmable Gate Arrays (FPGAs). The aim of the sensor is to measure performance variations during the life-cycle of the device, such as process variability, critical path timing and temperature variations. The proposed topology, through the use of both combinational and sequential FPGA elements, amplifies the time of a signal traversing a delay chain to produce a pulse whose width is the sensor’s measurement. The sensor is fully self-timed, avoiding the need for clock distribution networks and eliminating the limitations imposed by the system clock. One single off- or on-chip time-to-digital converter is able to perform digitization of several sensors in a single operation. These features allow for a simplified approach for designers wanting to intertwine a multi-purpose sensor network with their application logic. Employed as a temperature sensor, it has been measured to have an error of ±0.67 °C, over the range of 20–100 °C, employing 20 logic elements with a 2-point calibration.

A self-adaptive image processing application based on evolvable and scalable hardware

Evolvable Hardware (EH) is a technique that consists of using reconfigurable hardware devices whose configuration is controlled by an Evolutionary Algorithm (EA). Our system consists of a fully-FPGA implemented scalable EH platform, where the Reconfigurable processing Core (RC) can adaptively increase or decrease in size. Figure 1 shows the architecture of the proposed System-on-Programmable-Chip (SoPC), consisting of a MicroBlaze processor responsible of controlling the whole system operation, a Reconfiguration Engine (RE), and a Reconfigurable processing Core which is able to change its size in both height and width. This system is used to implement image filters, which are generated autonomously thanks to the evolutionary process. The system is complemented with a camera that enables the usage of the platform for real time applications.

Explointing FPGA block memories for protected cryptographic implementations

Modern Field Programmable Gate Arrays (FPGAs) are power packed with features to facilitate designers. Availability of features like huge block memory (BRAM), Digital Signal Processing (DSP) cores, embedded CPU makes the design strategy of FPGAs quite different from ASICs. FPGA are also widely used in security-critical application where protection against known attacks is of prime importance. We focus ourselves on physical attacks which target physical implementations. To design countermeasures against such attacks, the strategy for FPGA designers should also be different from that in ASIC. The available features should be exploited to design compact and strong countermeasures. In this paper, we propose methods to exploit the BRAMs in FPGAs for designing compact countermeasures. BRAM can be used to optimize intrinsic countermeasures like masking and dual-rail logic, which otherwise have significant overhead (at least 2X). The optimizations are applied on a real AES-128 co-processor and tested for area overhead and resistance on Xilinx Virtex-5 chips. The presented masking countermeasure has an overhead of only 16% when applied on AES. Moreover Dual-rail Precharge Logic (DPL) countermeasure has been optimized to pack the whole sequential part in the BRAM, hence enhancing the security. Proper robustness evaluations are conducted to analyze the optimization for area and security.

Modeling sub-threshold slope and DIBL mismatch of sub-22nm FinFet

A great challenge for future information technologies is building reliable systems on top of unreliable components. Parameters of modern and future technology devices are affected by severe levels of process variability and devices will degrade and even fail during the normal lifeDme of the chip due to aging mechanisms. These extreme levels of variability are caused by the high device miniaturizaDon and the random placement of individual atoms. Variability is considered a "red brick" by the InternaDonal Technology Roadmap for Semiconductors. The session is devoted to this topic presenDng research experiences from the Spanish Network on Variability called VARIABLES. In this session a talk entlited "Modeling sub-threshold slope and DIBL mismatch of sub-22nm FinFet" was presented.

Development of a versatile biotinylated material based on SU-8

The negative epoxy-based SU-8 photoresist has a wide variety of applications within the semiconductor industry, photonics and lab-on-a-chip devices, and it is emerging as an alternative to silicon-based devices for sensing purposes. In the present work, biotinylation of the SU-8 polymer surface promoted by light is reported. As a result, a novel, efective, and low-cost material, focusing on the immobilization of bioreceptors and consequent biosensing, is developed. This material allows the spatial discrimination depending on the irradiation of desired areas. The most salient feature is that the photobiotin may be directly incorporated into the SU-8 curing process, consequently reducing time and cost. The potential use of this substrate is demonstrated by the immunoanalytical detection of the synthetic steroid gestrinone, showing excellent performances. Moreover, the naked eye biodetection due to the transparent SU-8 substrate, and simple instrumental quantication are additional advantages.

Factors driving the carbon mineralization priming effect in a sandy loam soil amended with different types of biochar

The effect of biochar on the soil carbon mineral- ization priming effect depends on the characteristics of the raw materials, production method and pyrolysis conditions. The goal of the present study is to evaluate the impact of three different types of biochar on physicochemical properties and CO2 emissions of a sandy loam soil. For this purpose, soil was amended with three different biochars (BI, BII and BIII) at a rate of 8 wt % and soil CO2 emissions were measured for 45 days. BI is produced from a mixed wood sieving from wood chip production, BII from a mixture of paper sludge and wheat husks and BIII from sewage sludge. Cumulative CO2 emissions of biochars, soil and amended soil were well fit to a simple first-order kinetic model with correlation coef- ficients (r 2 ) greater than 0.97. Results show a negative prim- ing effect in the soil after addition of BI and a positive prim- ing effect in the case of soil amended with BII and BIII. These results can be related to different biochar properties such as carbon content, carbon aromaticity, volatile matter, fixed carbon, easily oxidized organic carbon or metal and phenolic substance content in addition to surface biochar properties. Three biochars increased the values of soil field capacity and wilting point, while effects over pH and cation exchange capacity were not observed.

Optimization of optical systems for LED spot lights concerning the color uniformity

Spotlighting is one illumination field where the application of light emitting diodes (LED) creates many advantages. Commonly, the system for spot lights consists of a LED light engine and collimating secondary optics. Through angular or spatial separated emitted light from the source and imaging optical elements, a non uniform far field appears with colored rings, dots or patterns. Many feasible combinations result in very different spatial color distributions. Several combinations of three multi-chip light sources and secondary optical elements like reflectors and TIR lenses with additional facets or scattering elements were analyzed mainly regarding the color uniformity. They are assessed by the merit function Usl which was derived from human factor experiments and describes the color uniformity based on the visual perception of humans. Furthermore, the optical systems are compared concerning efficiency, peak candela and aspect ratio. Both types of optics differ in the relation between the color uniformity level and other properties. A plain reflector with a slightly color mixing light source performs adequate. The results for the TIR lenses indicate that they need additional elements for good color mixing or blended light source. The most convenient system depends on the requirements of the application.

A Dynamically Adaptable Image Processing Application Trading Off Between High Performance, Consumption and Dependability in Real Time

As embedded systems evolve, problems inherent to technology become important limitations. In less than ten years, chips will exceed the maximum allowed power consumption affecting performance, since, even though the resources available per chip are increasing, frequency of operation has stalled. Besides, as the level of integration is increased, it is difficult to keep defect density under control, so new fault tolerant techniques are required. In this demo work, a new dynamically adaptable virtual architecture (ARTICo3) to allow dynamic and context-aware use of resources is implemented in a high performance Wireless Sensor node (HiReCookie) to perform an image processing application.

Desarrollo de un sistema portátil de monitorización personal

Un sistema de monitorización personal está pensado para mantener un control constante de ciertos parámetros vitales, de forma que se pueda realizar un registro de los mismos o generar algún tipo de alarma si se salen fuera de sus parámetros habituales o alcanzan cotas de riesgo. En este aspecto, se convierten en una opción cada vez más atractiva cuanto menos invasivos son, de forma que el objetivo es conseguir un sistema que monitorice al paciente sin entorpecer sus acciones cotidianas. Por este motivo, los dispositivos wearables son una buena opción. Un reloj, un colgante o una pulsera son elementos que llevan muchas personas, y por tanto, susceptibles de incorporar un procesador y algunos sensores que realicen las medidas. En este Trabajo de Fin de Grado se pretende realizar un prototipo sencillo de un sistema de monitorización personal que ilustre el funcionamiento de una red de área personal (WBAN) a partir de una plataforma de desarrollo preexistente. La plataforma en cuestión es el eZ430-Chronos de Texas Instruments, un System on Chip que incorpora sensores de aceleración, temperatura y presión. El System on Chip se encapsula en la forma de un reloj de pulsera. Además, se dispone de una banda, fabricada por BM innovations, que permite medir el ritmo cardíaco. En primer lugar se hará un análisis del sistema disponible, por un lado de la arquitectura hardware y firmware del dispositivo, y por otro lado de la arquitectura del software del cliente para PC. El firmware disponible en un principio permite únicamente la captura y registro de algunos parámetros del entorno, así como de las pulsaciones. Adicionalmente, el eZ430-Chronos dispone de un cliente para PC que le permite descargar los datos almacenados en la memoria flash al PC, así como configurar ciertos valores. En una segunda fase, se modificará el firmware para convertirlo en un sistema de monitorización personal, en el que se le retira al usuario la capacidad de control sobre la ejecución y se automatizan los procesos de adquisición y descarga de datos. Además, se creará una aplicación para PC que tenga la misma funcionalidad que el software original, aparte de incluir algunas características adicionales.