12 resultados para POLY(3-HYDROXYBUTYRATE-CO-3-HYDROXYVALERATE)
em Universidade do Algarve
Resumo:
A detailed investigation both of the DC and of the AC electrical properties of the Schottky barrier formed between aluminium and electrodeposited poly(3-methylthiophene) is reported. The devices show rectification ratios up to 2 x 10(4) which can be increased further after post-metal annealing. The reverse characteristics of the devices follow predictions based on the image-force lowering of the Schottky barrier, from which the doping density can be estimated, As the forward voltage increases, the device current is limited by the bulk resistance of the polymer with some evidence for injection limitation at the gold counter-electrode at high bias. In the bulk-limited regime, the device current is thermally activated near room temperature with an activation energy in the range 0.2-0.3 eV. Below about 150 K the device current is almost independent of temperature. Capacitance-voltage plots obtained at frequencies well below the device relaxation frequency indicate the presence of two distinct acceptor states, A set of shallow acceptor states are active in forward bias and are believed to determine the bulk conductivity of the polymer. A set of deeper accepters are active only for very small forward voltages and for all reverse voltages, namely when band banding causes the Fermi energy to cross these states. The density of these deeper states is approximately an order of magnitude greater than that of the shallow states. Evidence is presented also for the influence of fabrication conditions on the formation of an insulating interfacial layer at the rectifying interface. The presence of such a layer leads to inversion at the polymer surface and a modification of the I-V characteristics.
Resumo:
Both the DC and AC admittance of Schottky barrier diodes formed at the interface of aluminium and poly(3-methyl thiophene) have been investigated in some detail. The capacitance-voltage plots for the devices suggest the presence of two acceptor states, one shallow and one deep. The total concentration of acceptor states, 10 24-10 26 m -3 depending on the degree of undoping, agrees well with estimates from the reverse I-V characteristics assuming image force lowering of the interfacial potential barrier.
Resumo:
Schottky-barrier devices were formed from electropolymerised films of poly (3-methylthiophene) (PMeT). Thermal annealing of a partially undoped film led to diodes with rectification ratios as high as 5900 at 1 V and 50,000 at 2.5 V and ideality factors slightly above 2. The temperature dependence of ac loss tangent and forward currents are identical suggesting that bulk effects dominate device behaviour event at very low forward voltages. Below 250 K forward currents are essentially independent of temperature. Preliminary TSC measurements show the presence of at least two trapping levels in the devices. © 1993.
Resumo:
Field effect devices have been formed in which the active layer is a thin film of poly(3-methylthiophene) grown electrochemically onto preformed source and drain electrodes. Although a field effect is present after electrochemical undoping, stable device characteristics with a high modulation ratio are obtained only after vacuum annealing at an elevated temperature, and only then if the devices are held in vacuo. The polymer is shown to be p type and the devices operate in accumulation only. The hole mobility in devices thermally annealed under vacuum is around 10 -3 cm 2 V -1 s -1. On exposure to ambient laboratory air, the device conductance increases by several orders of magnitude. This increase may be reversed by subjecting the device to a further high-temperature anneal under vacuum. Subsidiary experiments show that these effects are caused by the reversible doping of the polymer by gaseous oxygen.
Resumo:
Deep Level Transient Spectroscopy (DLTS) has been used to investigate hole traps in the depletion region of Schottky barrier diodes formed from electropolymerised poly(3-methylthiophene). The capacitance transients appear to be composed of a fast and a slow component. Analysis of the slower component using the ''rate window'' technique yields isochronal differential capacitance curves that depend on temperature in the manner predicted by theory.
Resumo:
Evidence is presented which shows that anomalies in the I-V characteristics of Schottky diodes formed from electrodeposited poly(3-methylthiophene) are related to the time films are held under vacuum prior to deposition of the rectifying aluminium electrode. For short times (similar to 15 mins) a plateau appears in the forward bias characteristic which disappears leading to a significant voltage offset as the device ages or is driven into high forward bias.
Resumo:
Conjugated organic semiconductors have been submitted to various electrical measurement techniques in order to reveal information about shallow levels and deep traps in the forbidden gap. The materials consisted of poly[2-methoxy, 5 ethyl (2' hexyloxy) paraphenylenevinylene] (MEH-PPV), poly(3-methylthiophene) (PMeT), and alpha-sexithienyl (alpha T6) and the employed techniques were IV, CV, admittance spectroscopy, TSC, capacitance and current transients. (C) 1999 Elsevier Science B.V. All rights reserved.
Resumo:
Schottky barrier diodes are made from virtually all semiconducting polymers. Application of Schottky barriers on the development of electronic devices built from semiconducting polymers prompted this research. The article investigated the dc and ac admittance of Schottky barrier which occur at the interface between aluminum and poly(3-methyl thiophene) made ready by electropolymerisation. The experiment revealed that the interfacial layers occurring in polymer Schottky barriers is significant in the response of the controlling device.
Resumo:
The photocurrent action spectrum of a Schottky diode formed from electrodeposited poly(3-methylthiophene) is shown to follow closely the UV-visible absorption spectrum. At low forward bias, the peak photocurrent asymptotes to the expected square-root dependence on total potential, V-t, across the depletion region. At high reverse bias the superlinear dependence of the photocurrent on V-t suggests that internal photoemission from the rectifying aluminium electrode may be the dominant process.
Resumo:
Schottky diodes resulting from an intimate contact of aluminum on electro-deposited poly(3-methylthiopene), PMeT, have been studied by admittance spectroscopy, capacitance-voltage and current-voltage measurements, and optically-induced current transients. The loss-tangents show the existence of interface states that can be removed by vacuum annealing, also visible in the transients. Furthermore, the CV curves don't substantiate the idea of movement of the dopant ions.
Resumo:
Schottky diodes resulting from an intimate contact of aluminum on electrodeposited poly(3-methylthiopene) were studied by admittance spectroscopy, capacitance-voltage measurements and voltaic and optically-induced current and capacitance transients. The loss tangents show the existence of interface states that can be removed by vacuum annealing. Furthermore, the C-V curves contradict the idea of movement of the dopant ions.
Resumo:
Schottky barrier diodes based on Al/poly(3-methylthiophene)/Au have been fabricated and their electrical behaviour investigated. I-V characteristics revealed a dependence on the fabrication conditions, specifically on the time under vacuum prior to evaporation of the rectifying contact and post-metal annealing at elevated temperature. The available evidence is consistent with the formation of a thin insulating layer between the metal and the polymer following these procedures. Long periods under vacuum prior to deposition of the aluminium electrode reduced the likelihood of such a layer forming. Capacitance-voltage plots of the devices were stable to voltage cycling, so long as the forward voltage did not exceed similar to 1 V. Above this a small degree of hysteresis was observed, which is attributed to the filling/emptying of interface states or traps in the polymer.