Exposure to microbial volatile organic compounds in a waste-handling unit

The production of MVOC by fungi has been taken into account especially from the viewpoint of indoor pollution with microorganisms but the relevance of fungal metabolites in working environments has not been sufficiently studied. The purpose of this study was to assess exposure to MVOCs in a waste-handling unit. It was used Multirae equipment (RAE Systems) to measured MVOCs concentration with a 10.6 eV lamps. The measurements were done near workers nose and during the normal activities. All measurements were done continuously and had the duration of 5 minutes at least. It was consider the higher value obtained in each measurement. In addition, for knowing fungi contamination, five air samples of 50 litres were collected through impaction method at 140 L/minute, at one meter tall, on to malt extract agar with the antibiotic chloramphenicol (MEA). MVOCs results range between 4.7 ppm and 8.9 ppm in the 6 locations consider. These results are eight times higher than normally obtained in indoor settings. Considering fungi results, two species were identified in air, being the genera Penicillium found in all the samples in uncountable colonies and Rhizopus only in one sample (40 UFC/m3). These fungi are known as MVOCs producers, namely terpenoids, ketones, alcohols and others. Until now, there has been no evidence that MVOCs are toxicologically relevant, but further epidemiological research is necessary to elucidate their role on human’s health, particularly in occupational settings where microbiological contamination is common. Additionally, further research should concentrate on quantitative analyses of specific MVOCs.

Assessment of bacteria and virus emissions at a refuse derived fuel plant and other waste handling facilities /

Mode of access: Internet.

Solid waste handling and disposal in multistory buildings and hospitals.

"Research initiated by the Project Planning and Pollution Control Division, Dept. of County Engineer, County of Los Angeles."

Solid waste handling and disposal in multistory buildings and hospitals.

"Research initiated by the Project Planning and Pollution Control Division, Dept. of County Engineer, County of Los Angeles."

Waste Stream Investigation from Perspective of Changing Waste Legislation at Green Sand Foundries

The update of the Finnish legislation concerning waste was unavoidable, to comply with the European Union (EU) requirements defined in the EU-Directive on Waste. The new waste law updates were enacted into the Finnish legislation on the 11.03.2011 and targeted for applicability by the 11.03.2012. This thesis investigates the implications of the new amendments to the waste legislation from the perspective of green sand foundries. The investigations are conducted by comparing two of Componenta’s green sand foundries and evaluating their waste streams. Additionally, the impacts of legislation amendments are critiqued on their environmental and economic aspects. The study’s comparison of waste fractions at the two foundries reveals that sand is dominant in absolute tonnage and costs. The increments of waste taxes forces foundries to focus on waste management, recycling and disposing. The new legislation’s promotion of material efficiency, also guides foundries towards the prevention of waste. A potential preventive measure is to regenerate waste sand resulting to cost savings on both raw-materials and waste management. However, the lack of absolute targets for waste prevention or recycling rates discourages the interests towards creating or adopting new technologies and methods for the waste handling.

Twelve factors influencing sustainable recycling of municipal solid waste in developing countries

Sustainable management of solid waste is a global concern, as exemplified by the United Nations Millennium Development Goals (MDG) that 191 member states support. The seventh MDG indirectly advocates for municipal solid waste management (MSWM) by aiming to ensure environmental sustainability into countries’ policies and programs and reverse negative environmental impact. Proper MSWM will likely result in relieving poverty, reducing child mortality, improving maternal health, and preventing disease, which are MDG goals one, four, five, and six, respectively (UNMDG, 2005). Solid waste production is increasing worldwide as the global society strives to obtain a decent quality of life. Several means exist in which the amount of solid waste going to a landfill can be reduced, such as incineration with energy production, composting of organic wastes, and material recovery through recycling, which are all considered sustainable methods by which to manage MSW. In the developing world, composting is already a widely-accepted method to reduce waste fated for the landfill, and incineration for energy recovery can be a costly capital investment for most communities. Therefore, this research focuses on recycling as a solution to the municipal solid waste production problem while considering the three dimensions of sustainability environment, society, and economy. First, twenty-three developing country case studies were quantitatively and qualitatively examined for aspects of municipal solid waste management. The municipal solid waste (MSW) generation and recovery rates, as well as the composition were compiled and assessed. The average MSW generation rate was 0.77 kg/person/day, with recovery rates varying from 5 – 40%. The waste streams of nineteen of these case studies consisted of 0 – 70% recyclable material and 17 – 80% organic material. All twenty-three case studies were analyzed qualitatively by identifying any barriers or incentives to recycling, which justified the creation of twelve factors influencing sustainable municipal solid waste management (MSWM) in developing countries. The presence of regulations, enforcement of laws, and use of incentive schemes constitutes the first factor, Government Policy. Cost of MSWM operations, the budget allocated to MSWM by local to national governments, as well as the stability and reliability of funds comprise the Government Finances factor influencing recycling in the third world. Many case studies indicated that understanding features of a waste stream such as the generation and recovery rates and composition is the first measure in determining proper management solutions, which forms the third factor Waste Characterization. The presence and efficiency of waste collection and segregation by scavengers, municipalities, or private contractors was commonly addressed by the case studies, which justified Waste Collection and Segregation as the fourth factor. Having knowledge of MSWM and an understanding of the linkages between human behavior, waste handling, and health/sanitation/environment comprise the Household Education factor. Individuals’ income influencing waste handling behavior (e.g., reuse, recycling, and illegal dumping), presence of waste collection/disposal fees, and willingness to pay by residents were seen as one of the biggest incentives to recycling, which justified them being combined into the Household Economics factor. The MSWM Administration factor was formed following several references to the presence and effectiveness of private and/or public management of waste through collection, recovery, and disposal influencing recycling activity. Although the MSWM Personnel Education factor was only recognized by six of the twenty-two case studies, the lack of trained laborers and skilled professionals in MSWM positions was a barrier to sustainable MSWM in every case but one. The presence and effectiveness of a comprehensive, integrative, long-term MSWM strategy was highly encouraged by every case study that addressed the tenth factor, MSWM Plan. Although seemingly a subset of private MSWM administration, the existence and profitability of market systems relying on recycled-material throughput, involvement of small businesses, middlemen, and large industries/exporters is deserving of the factor Local Recycled-Material Market. Availability and effective use of technology and/or human workforce and the safety considerations of each were recurrent barriers and incentives to recycling to warrant the Technological and Human Resources factor. The Land Availability factor takes into consideration land attributes such as terrain, ownership, and development which can often times dictate MSWM. Understanding the relationships among the twelve factors influencing recycling in developing countries, made apparent the collaborative nature required of sustainable MSWM. Factors requiring the greatest collaborative inputs include waste collection and segregation, MSWM plan, and local recycled-material market. Aligning each factor to the societal, environmental, and economic dimensions of sustainability revealed the motives behind the institutions contributing to each factor. A correlation between stakeholder involvement and sustainability existed, as supported by the fact that the only three factors driven by all three dimensions of sustainability were the same three that required the greatest collaboration with other factors. With increasing urbanization, advocating for improved health for all through the MDG, and changing consumption patterns resulting in increasing and more complex waste streams, the utilization of the collaboration web offered by this research is ever needed in the developing world. Through its use, the institutions associated with each of the twelve factors can achieve a better understanding of the collaboration necessary and beneficial for more sustainable MSWM.

Jätteen määrän vähentäminen ja jätteenkäsittelymahdollisuuksien selvittäminen pinnoitetehtaassa

EU:n mukanaan tuomat uudet vaatimukset jätteenpoltolle aiheuttavat suuria muutoksia Dynea Overlays Oy:n jätteen käsittelylle. Samalla tehdasalueella tapahtuva jätteenpoltto päättyy todennäköisesti vuoden 2005 lopulla. Tästä syystä tehtaalla syntyville jätteille haettiin uusia hävitysreittejä. Jokaiselle jätejakeelle löydettiin uusi hävitysvaihtoehto, jotka pääosin ovat jätteen hyödyntämistä energiana. Pinnoitejätteet, kovetetut hartsit ja kuitujäte hyödynnetään energiana, tyhjät kertakäyttökontit joko otetaan uudelleenkäyttöön tai toimitetaan purettuina metallin- ja muovinkeräykseen. Työn toinen tavoite oli jätteen määrän vähentäminen. Jätteen määrää vähentämällä saadaan alennettua jätteenkäsittelykustannuksia sekä parannettua saantoa. Saanto on mittari, jota seurataan Dynean kaikilla pinnoitetehtailla ympäri maailmaa. Yrityksen johto on asettanut tavoitteeksi nostaa saannon vuoden 2003 tasolta 90 % tasolle 93 % vuoden 2004 loppuun mennessä. Jo vuoden 2004 ensimmäisinä kuukausina saanto näyttää parantuneen tavoitetasolle asiaan kiinnitetyn huomion ja tarkentuneen raportoinnin seurauksena.

8

Occupational exposures to fungi are very frequent and are known to cause chronic or acute symptoms. To better assess health risks related to fungal exposure, it is crucial to characterize precisely the airborne fungal community in terms of quantity and composition. The objective of this chapter is to synthesize existing knowledge of airborne fungal contamination in various occupational settings. We analyzed 134 papers published between 2000 and 2014 focusing on five different work sectors considered as highly contaminated (i.e., more than 1000 fungal particles/m3): animal confinement buildings, sawmills, waste handling, the food industry, and grain/plant handling. Results show that harvesting grain, washing cheese, and handling salami seem to be the occupational situations with the worst potential for exposure. Moreover, a lack of standardized sampling and analysis methods among countries and even within the same country is highlighted. Occupational exposure limit values do not exist. Recommendations and guidelines based on culture-dependent methods, which are now recognized to underestimate true concentrations, are proposed. Those recommendations are frequently exceeded and protective measures are not always easy to implement.

Matala-aktiivisen metallijätteen aktiivisuusmittaukset Loviisan voimalaitoksella

Tämän diplomityön lähtökohtana oli metallijätteen mittausmenetelmien kehittäminen Loviisan voimalaitoksella. Työn taustalla oli myös Säteilyturvakeskuksen antaman ohjeen YVL 8.2 ’Ydinjätteiden ja käytöstä poistettujen ydinlaitosten vapauttaminen valvonnasta’ uusinta. Työssä arvioitiin miten YVL 8.2 -ohjeen päivitys vaikuttaa Loviisan voimalaitoksen metallijätteen käsittelyyn vapautusmenettelyn osalta. Diplomityössä arvioitiin eri aktiivisuusmittausmenetelmien havaitsemia aktiivisuuksia metallijätteessä. Metallijätteen mittausmenetelmien arviointi aloitettiin kirjalliseen materiaaliin tutustumisella, jonka jälkeen mittausmenetelmiä verrattiin kokeellisesti. Verrattavia mittauksia olivat suora kontaminaatiomittaus, gammaspektrometrinen mittaus, kuiva-, märkä-, ja happopyyhintänäytteet sekä mittaus Condor E -monitorilla. Diplomityö sisältää myös arvioinnin ajoneuvojen säteilymittauslaitteiston käytöstä metallijätteen valvonnasta vapauttamisessa. Työssä arvioitiin myös mittausmenetelmän vaikutusta logistiikkaketjuun Loviisan voimalaitoksella ja kaiken metallijätteen loppusijoittamisen vaikutuksia. Nykyinen metallijätteen vapautusmenettely on raskas, eikä täysin uusitun ohjeen YVL 8.2 vaatimusten mukainen. Diplomityön tuloksena metallijätteen käsittelymenetelmäksi suositellaan metallijätteen vapauttamista valvonnasta seuraavin menettelyin. Pieni metallijäte tulisi huolellisen esimittauksen jälkeen pakata ja analysoida gammaspektrometrisesti. Suuret metallijätekappaleet tulisi analysoida pyyhintänäytteiden perusteella. Pyyhintänäytteiden analysointi kannattaisi suorittaa gammaspektrometrillä, koska sillä saavutetaan tarkin tulos ja se on täysin ohjeen YVL 8.2 vaatimusten mukainen. Loppusijoitusluolaan tulisi sijoittaa mahdollisimman pieni määrä vapauttamiskelpoista metallijätettä. Myös ajoneuvojen säteilymittauslaitteiston käyttöä varmentavana mittauksena tulisi tehostaa.

The Current Situation of Sewage Sludge and Manure Treatment in Livestock Enterprises in the Leningrad Region

The problem concerning livestock waste handling in the Leningrad region has been subjected to a number of research works. However, the requirements for use of manure and sewage sludge as well as for treatment processes are not certain. So, this problem remains relevant and, therefore, further investigation ought to be made. Currently a large amount of sewage sludge and manure is generated in the Leningrad region. These livestock wastes have to be obligatory treated. The most common methods for treatment in the region, such as anaerobic digestion, composting and aging as well as the most potential methods are described in the thesis. The most potential methods for the Leningrad region are anaerobic digestion, composting and combustion. Each method has strengths and weaknesses, which are also considered in the paper. Aging was not considered as potential treatment method because it does not meet the sanitary and epidemiological requirements. Furthermore, the work gives an overview and comparison of Finnish and Russian legislative and normative acts concerning livestock wastes handling. On the whole the requirements of the Russian Federation concerning sewage sludge and manure are not much different from the Finnish ones.

Analyzing the Background Information of an Activity-Based Costing System

The aim of this thesis was to analyze the background information of an activity-based costing system, which is being used in a domestic forest industry company. The reports produced by the system have not been reliable, and this has caused the utilization of the system to diminish. The study was initiated by examining the theory of activity-based costing. It was also discovered, that the system produces management accounting information and therefore also that theory was introduced briefly. Next the possible sources of errors were examined. The significance of these errors was evaluated and waste handling was chosen as a subject of further study. The problem regarding waste handling was that there is no waste compensation in current model. When paper or board machine produces waste, it can be used as raw material in the process. However, at the moment the product, which is being produced, at the time does not get any compensation. The use of compensation has not been possible due to not knowing the quantity of process waste. As a result of the study a calculatory model, which enables calculating the quantity of process waste based on the data from the mill system, was introduced. This, for one, enables starting to use waste compensation in the future.

Diagnóstico dos riscos e impactos ambientais da suinocultura no Ribeirão dos Pinheirinhos, município de Torrinha, (SP)

The porcine activity is characterized by its great pollution capacity, generally produce loads of waste that usually are released in superficial water or soil without concern for the consequences to the environment. With this in mind, this study aimed to adjust the porcine production to the protection of water resources, in particular, Ribeirão dos Pinheirinhos in the town of Torrinha (SP), through inventory and diagnosis of the environmental impacts already present and environmental hazards linked to the activity in question. To achieve the proposed objectives, the productions of porcine on the studied area were raised and georeferenced, viewed and analyzed according to the technical and scientific literature. The production visited showed to be at odds with the protection of water resources due to lack of technical criteria in the development of treatment systems and waste handling, indiscriminate use of effluent and waste in the fertilization of crops and the lack of knowledge of producers on the influence of porcine waste into the environment. Based on these results, were set guidelines for action in the environmental awareness of farmers, to stimulate voluntary and conscious initiatives of environmental conservation in the direction of settlement of the activity.

Percepções sociais sobre o futuro da humanidade no planeta: um estudo na cidade de Piracicaba, SP

A pesquisa sobre as percepções de residentes da região de Piracicaba em relação às questões ambientais e ao futuro da humanidade no planeta foi desenvolvida com base em um questionário semi-estruturado. As questões buscaram levantar dados autoavaliativos sobre perfil, comportamentos, estado de humor, qualidade de vida, condição econômica e hábitos de consumo, práticas para destinação de resíduos, iniciativas de exercício de cidadania em prol da sustentabilidade socioambiental, para enfim, indagar sobre percepções de futuro e avaliações sobre o contexto socioambiental dos participantes da pesquisa. A aplicação dos questionários foi feita de forma aleatória estratificada nos bairros das cinco regiões da cidade de Piracicaba: Norte, Sul, Leste, Oeste e Centro. Por meio dessas aplicações, foram obtidos 655 questionários, que foram sistematizados, tabulados e analisados estatisticamente, utilizando-se gráficos de frequência, o Teste de Kruskal Wallis, os Testes de Correlação de Spearman e Kendall, o Teste de Qui-Quadrado e o Teste Exato de Fisher. Foram também criadas nuvens de palavras, desenvolvidas no software online \"Wordle\" (FEINBERG, 2014). Os resultados obtidos com essa pesquisa e as análises desenvolvidas indicam que 227 pessoas, isto é, aproximadamente 35% dos respondentes, possui uma percepção pessimista sobre o futuro da humanidade no planeta. Porém, 493 pessoas, o equivalente a aproximadamente 75% do total de respondentes, considerou que, dentre as alternativas apresentadas no questionário (Desenvolvimento de tecnologias; Controle de natalidade; Educação e mudanças culturais; Cobrança de impostos com base nos impactos ambientais; Intervenção do Estado), a educação e mudanças culturais são fundamentais no processo de transformação social e de superação das problemáticas ambientais. Observou-se também que a crise hídrica vivenciada na época em que os questionários foram aplicados também influenciou na percepção social dos respondentes, uma vez que a palavra \"água\" foi citada 380 vezes. Por meio do trabalho, foi também possível analisar o comportamento ambiental dos pesquisados, notando-se que ainda há a necessidade de promoção de atividades educacionais e comunicacionais que possam estimular a adoção de hábitos e comportamentos mais comprometidos com ideias de sustentabilidade e que levem a mudanças mais efetivas nos padrões de relacionamento entre sociedade e meio ambiente.

Validation of the Swiss methane emission inventory by atmospheric observations and inverse modelling

Atmospheric inverse modelling has the potential to provide observation-based estimates of greenhouse gas emissions at the country scale, thereby allowing for an independent validation of national emission inventories. Here, we present a regional-scale inverse modelling study to quantify the emissions of methane (CH₄) from Switzerland, making use of the newly established CarboCount-CH measurement network and a high-resolution Lagrangian transport model. In our reference inversion, prior emissions were taken from the "bottom-up" Swiss Greenhouse Gas Inventory (SGHGI) as published by the Swiss Federal Office for the Environment in 2014 for the year 2012. Overall we estimate national CH₄ emissions to be 196 ± 18 Gg yr⁻¹ for the year 2013 (1σ uncertainty). This result is in close agreement with the recently revised SGHGI estimate of 206 ± 33 Gg yr⁻¹ as reported in 2015 for the year 2012. Results from sensitivity inversions using alternative prior emissions, uncertainty covariance settings, large-scale background mole fractions, two different inverse algorithms (Bayesian and extended Kalman filter), and two different transport models confirm the robustness and independent character of our estimate. According to the latest SGHGI estimate the main CH₄ source categories in Switzerland are agriculture (78 %), waste handling (15 %) and natural gas distribution and combustion (6 %). The spatial distribution and seasonal variability of our posterior emissions suggest an overestimation of agricultural CH₄ emissions by 10 to 20 % in the most recent SGHGI, which is likely due to an overestimation of emissions from manure handling. Urban areas do not appear as emission hotspots in our posterior results, suggesting that leakages from natural gas distribution are only a minor source of CH₄ in Switzerland. This is consistent with rather low emissions of 8.4 Gg yr⁻¹ reported by the SGHGI but inconsistent with the much higher value of 32 Gg yr⁻¹ implied by the EDGARv4.2 inventory for this sector. Increased CH₄ emissions (up to 30 % compared to the prior) were deduced for the north-eastern parts of Switzerland. This feature was common to most sensitivity inversions, which is a strong indicator that it is a real feature and not an artefact of the transport model and the inversion system. However, it was not possible to assign an unambiguous source process to the region. The observations of the CarboCount-CH network provided invaluable and independent information for the validation of the national bottom-up inventory. Similar systems need to be sustained to provide independent monitoring of future climate agreements.

Preliminary risk analysis applied to the handling of health-care waste

Between 75% and 90% of the waste produced by health-care providers no risk or is "general" health-care waste, comparable to domestic waste. The remaining 10-25% of health-care waste is regarded as hazardous due to one or more of the following characteristics: it may contain infectious agents, sharps, toxic or hazardous chemicals or it may be radioactive. Infectious health-care waste, particularly sharps, has been responsible for most of the accidents reported in the literature. In this work the preliminary risks analysis (PRA) technique was used to evaluate practices in the handling of infectious health-care waste. Currently the PRA technique is being used to identify and to evaluate the potential for hazard of the activities, products, and services from facilities and industries. The system studied was a health-care establishment which has handling practices for infectious waste. Thirty-six procedures related to segregation, containment, internal collection, and storage operation were analyzed. The severity of the consequences of the failure (risk) that can occur from careless management of infectious health-care waste was classified into four categories: negligible, marginal, critical, and catastrophic. The results obtained in this study showed that events with critics consequences, about 80%, may occur during the implementation of the containment operation, suggesting the need to prioritize this operation. As a result of the methodology applied in this work, a flowchart the risk series was also obtained. In the flowchart the events that can occur as a consequence of a improper handling of infectious health-care waste, which can cause critical risks such as injuries from sharps and contamination (infection) from pathogenic microorganisms, are shown.