Modeling of the Fluid-Structure Interaction in Inelastic Piping Systems

In many engineering applications, compliant piping systems conveying liquids are subjected to inelastic deformations due to severe pressure surges such as plastic tubes in modern water supply transmission lines and metallic pipings in nuclear power plants. In these cases the design of such systems may require an adequate modeling of the interactions between the fluid dynamics and the inelastic structural pipe motions. The reliability of the prediction of fluid-pipe behavior depends mainly on the adequacy of the constitutive equations employed in the analysis. In this paper it is proposed a systematic and general approach to consistently incorporate different kinds of inelastic behaviors of the pipe material in a fluid-structure interaction analysis. The main feature of the constitutive equations considered in this work is that a very simple numerical technique can be used for solving the coupled equations describing the dynamics of the fluid and pipe wall. Numerical examples concerning the analysis of polyethylene and stainless steel pipe networks are presented to illustrate the versatility of the proposed approach.

Underground insulated piping systems : excluding walk-in tunnels.

"Prepared under Contract No. CST 263 between the National Academy of Sciences and the National Bureau of Standards."

Failure assessments of corroded pipelines with axial defects using stress-based criteria: Numerical studies and verification analyses

Conventional procedures used to assess the integrity of corroded piping systems with axial defects generally employ simplified failure criteria based upon a plastic collapse failure mechanism incorporating the tensile properties of the pipe material. These methods establish acceptance criteria for defects based on limited experimental data for low strength structural steels which do not necessarily address specific requirements for the high grade steels currently used. For these cases, failure assessments may be overly conservative or provide significant scatter in their predictions, which lead to unnecessary repair or replacement of in-service pipelines. Motivated by these observations, this study examines the applicability of a stress-based criterion based upon plastic instability analysis to predict the failure pressure of corroded pipelines with axial defects. A central focus is to gain additional insight into effects of defect geometry and material properties on the attainment of a local limit load to support the development of stress-based burst strength criteria. The work provides an extensive body of results which lend further support to adopt failure criteria for corroded pipelines based upon ligament instability analyses. A verification study conducted on burst testing of large-diameter pipe specimens with different defect length shows the effectiveness of a stress-based criterion using local ligament instability in burst pressure predictions, even though the adopted burst criterion exhibits a potential dependence on defect geometry and possibly on material`s strain hardening capacity. Overall, the results presented here suggests that use of stress-based criteria based upon plastic instability analysis of the defect ligament is a valid engineering tool for integrity assessments of pipelines with axial corroded defects. (C) 2008 Elsevier Ltd. All rights reserved.

Effects of gelation temperature on the Mozzarella-type curd made from buffalo and cows’ milk. 1: Rheology & microstructure

The rheology and microstructure of Mozzarella-type curds made from buffalo and cows’ milk were measured at gelation temperatures of 28, 34 and 39 °C after chymosin addition. The maximum curd strength (G′) was obtained at a gelation temperature of 34 °C in both types of bovine milk. The viscoelasticity (tan δ) of both curds was increased with increasing gelation temperature. The rennet coagulation time was reduced with increase of gelation temperature in both types of milk. Frequency sweep data (0.1–10Hz was recorded 90 min after chymosin addition, and both milk samples showed characteristics of weak viscoelastic gel systems. When both milk samples were subjected to shear stress to break the curd system at constant shear rate, 95 min after chymosin addition, the maximum yield stress was obtained at the gelation temperatures of 34 °C and 28 °C in buffalo and cows’ curd respectively. The cryo-SEM and CLSM techniques were used to observe the microstructure of Mozzarella-type curd. The porosity was measured using image J software. The cryo-SEM and CLSM micrographs showed that minimum porosity was observed at the gelation temperature of 34 °C in both types of milk. Buffalo curd showed minimum porosity at similar gelation temperature when compared to cows’ curd. This may be due to higher protein concentration in buffalo milk.

Estudo de sensores PZT aplicados à detecção de danos em tubulações

Pós-graduação em Engenharia Elétrica - FEIS

Definición e implantación de herramientas avanzadas 3D en el diseño integrado y eficiente de sistemas HVAC en buques, desde el proyecto conceptual hasta la producción

Uno de los aspectos más complicados del diseño de sistemas HVAC en buques es la correcta evaluación de las necesidades de aire fresco y el correcto dimensionado de los conductos que suministran dicho aire y evacuan el calor generado a bordo. Contrariamente a lo que sucede en los sistemas de tuberías, las características particulares del caudal de aire hacen que el dimensionado de los conductos sea muy sensible al trazado y geometría de los mismos, por lo que para obtener un buen diseño es necesaria una relación muy estrecha y una integración bidireccional entre los cálculos y el trazado de los propios conductos en el buque. Asumida la utilización de sistemas CAD/CAM para las tareas de diseño, históricamente, aquellos que permitían modelar conductos HVAC no incluían en su alcance de suministro los aspectos de cálculo, y como consecuencia de ello, el trazado de conductos se reducía a la inclusión en el modelo 3D de circuitos y sistemas previamente calculados y dimensionados, Así, servían únicamente para calcular interferencias con otros elementos del modelo 3D y para obtener posteriormente planos de fabricación y montaje. Esto, que por sí no es poco, dejaba el diseño de sistemas HVAC pendiente de una importante interacción manual y de habituales retrabajos, ya que cualquier modificación en el trazado de los conductos, consecuencia de otras necesidades del diseño, obligaba a los diseñadores a recalcular y redimensionar los conductos en un entorno diferente al del propio sistema CAD/CAM, y volver a realizar el modelado de los mismos, reduciendo significativamente las ventajas de la utilización de un modelo 3D. Partiendo de esta situación real, y con objeto de solucionar el problema que para el diseño y la propia producción del buque se creaba, se concibió una herramienta que permitiera la definición en el modelo 3D de diagramas de ventilación, el cálculo de pérdidas de presión, el dimensionado automático de los conductos, y que toda esta información pudiera estar disponible y reutilizarse en las etapas posteriores del diseño. Con ello, los diseñadores podrían realizar su trabajo en un entorno único, totalmente integrado con el resto de disciplinas. El objeto de esta Tesis Doctoral es analizar en detalle el problema y las ineficiencias actuales del diseño de HVAC, describir la innovadora herramienta concebida para paliar estas ineficiencias, detallando las bases sobre la que se construye, y destacar las ventajas que se obtienen de su uso. La herramienta en cuestión fue concebida como una funcionalidad adicional del sistema CAD/CAM naval FORAN, referente tecnológico en el mundo del diseño y la construcción navales, y como consecuencia de ellos se llevó a cabo el desarrollo correspondiente. En la actualidad, el sistema FORAN incluye en su alcance de suministro una primera versión de esta herramienta, cuya utilidad queda avalada por el uso que de la misma hacen astilleros y oficinas técnicas en todo el mundo. Esta Tesis Doctoral es eminentemente práctica. No es un estudio teórico de dudosa aplicación, sino que tiene por objeto aportar una solución eficiente a un problema real que muchos astilleros y oficinas técnicas, incluidas los más avanzados, padecen hoy en día. No tiene otra motivación que servir de ayuda para lograr diseñar y construir mejores barcos, en un plazo más corto, y a un coste menor. Nada más, pero nada menos. ABSTRACT One of the most complicated aspects of the design of HVAC systems in shipbuilding is the correct evaluation of the fresh air needs, the correct balancing of the ducts that supply this air and evacuate the existing heat on board. In opposition to piping systems, due to the particular characteristics of the air flow, the balancing of the ducts is very sensitive to the routing and the aspect of the ducts, so the correct design requires a close interconnectivity between calculations and routing. Already assumed the use of CAD/CAM systems for design tasks, historically, those CAD/CAM systems capable of modelling HVAC ducts did not cover calculation aspects, with the result that the routing of HVAC ducts was reduced solely to the input of previously balanced circuits into the 3D Product Model for the purpose of interference checking and generation of fabrication and assembly drawings. This situation, not negligible at all, put the design of HVAC ducts very dependent on manual operations and common rework task, as any modification in the routing of the HVAC ducts, derived from design needs, obliged engineers to re-balance the ducts and eventually to re-size them independently of the CAD-CAM environment, thus annulling the advantages of the 3D Product Model. With this situation in mind, and with the objective of filling the gap created in the design and construction of the ship, it was conceived a tool allowing the definition, within the 3D Product model, of HVAC diagrams, the calculation of pressure drops, the automatic dimensioning of ducts. With this, engineers could make the complete HVAC design in a single working environment, fully integrated with the rest of the disciplines. The present Ph. D. thesis analyses in deep the existing problem and the current lack of efficiency in HVAC design, describes the innovative tool conceived to minimize it, details the basis on which the tool is built, and highlights the advantages of its use. This tool was conceived as an additional functionality of the marine CAD/CAM system FORAN, a technological reference in the shipdesign and shipbuilding industry. As a consequence, it was developed, and nowadays FORAN System includes in its scope of supply a first version of the tool, with its usefulness endorsed by the fact that it is used by shipyards and shipdesign offices all over the world. This Ph. D. thesis is on top everything, of practical nature. It is not a theoretical study with doubtful application. On the contrary, its objective is to provide with an efficient solution for solving a real problem that many shipyards and shipdesign offices, including those more advanced, suffer nowadays. It has no other motivation that to help in the process of designing and building better and cheaper ships, within a shorter deliver time. Nothing more, but nothing less.

Investigation of standards, performance characteristics, and evaluation criteria for thermoplastic piping in residential plumbing systems /

"Sponsored by Office of Policy Development and Research, Department of Housing and Urban Development."

Protein-polysaccharide viscoelastic matrices: synergic effects of amylose on lysozyme physical gelation in aqueous dimethylsulfoxide

A synergic effect of amylose on rheological characteristics of lysozyme physical gels evolved out of dimethylsulfoxide-water was verified and analyzed. The dynamics of the gels were experimentally approached by oscillatory rheology. The synergic effect was characterized by a decrease in the threshold DMSO volume fraction required for lysozyme gelation, and by a significant strengthening of the gel structure at over-critical solvent and protein concentrations. Drastic changes in the relaxation and creep curve patterns for systems in the presence of amylose were verified. Complex viscosity dependence on temperature was found to conform to an Arrhenius-like equation, allowing the determination of an activation energy term (Ea, apparent) for discrimination of gel rigidity. A dilatant effect was found to be induced by temperature on the flow behavior of lysozyme dispersions in DMSO-H(2)O in sub-critical conditions for gelation, which was greatly intensified by the presence of amylose in the samples. That transition was interpreted as reflecting a change from a predominant colloidal flow regime, where globular components are the prevailing structural elements, to a mainly fibrillar, polymeric flow behavior.

Rheological, mechanical and mucoadhesive properties of thermoresponsive, bioadhesive binary mixtures composed of poloxamer 407 and carbopol 974P designed as platforms for implantable drug delivery systems for use in the oral cavity

This study described the formulation and characterisation of the viscoelastic, mechanical and mucoadhesive properties of thermoresponsive, binary polymeric systems composed of poloxamer (P407) and poly(acrylic acid, C974P) that were designed for use as a drug delivery platform within the oral cavity. Monopolymeric and binary polymeric formulations were prepared containing 10, 15 and 20% (w/w) poloxamer (407) and 0.10-0.25% (w/w) poly(acrylic acid, 934P). The flow theological and viscoelastic properties of the formulations were determined using controlled stress and oscillatory rheometry, respectively, the latter as a function of temperature. The mechanical and mucoadhesive properties (namely the force required to break the bond between the formulation and a pre-hydrated mucin disc) were determined using compression and tensile analysis, respectively. Binary systems composed of 10% (w/w) P407 and C934P were elastoviscous, were easily deformed under stress and did not exhibit mucoadhesion. Formulations containing 15 or 20% (w/w) Pluronic P407 and C934P exhibited a sol-gel temperature T(sol/gel), were viscoelastic and offered high elasticity and resistance to deformation at 37 degrees C. Conversely these formulations were elastoviscous and easily deformed at temperatures below the sol-gel transition temperature. The sol-gel transition temperatures of systems containing 15% (w/w) P407 were unaffected by the presence of C934P; however, increasing the concentration of C934P decreased the T(sol/gel) in formulations containing 20%(w/w) P407. Rheological synergy between P407 and C934P at 37 degrees C was observed and was accredited to secondary interactions between these polymers, in addition to hydrophobic interactions between P407 micelles. Importantly, formulations composed of 20% (w/w) P407 and C934P exhibited pronounced mucoadhesive properties. The ease of administration (below the T(sol/gel)) in conjunction with the viscoelastic (notably high elasticity) and mucoadhesive properties (at body temperature) render the formulations composed of 20% (w/w) P407 and C934P as potentially useful platforms for mucoadhesive, controlled topical drug delivery within the oral cavity. (c) 2009 Published by Elsevier B.V.

Dispersion of fillers in viscoelastic polymer matrices using Eulerian-Lagrangian approaches

Understanding the behavior of c omplex composite materials using mixing procedures is fundamental in several industrial processes. For instance, polymer composites are usually manufactured using dispersion of fillers in polymer melt matrices. The success of the filler dispersion depends both on the complex flow patterns generated and on the polymer melt rheological behavior. Consequently, the availability of a numerical tool that allow to model both fluid and particle would be very useful to increase the process insight. Nowadays there ar e computational tools that allow modeling the behavior of filled systems, taking into account both the behavior of the fluid (Computational Rheology) and the particles (Discrete Element Method). One example is the DPMFoam solver of the OpenFOAM ® framework where the averaged volume fraction momentum and mass conservation equations are used to describe the fluid (continuous phase) rheology, and the Newton’s second law of motion is used to compute the particles (discrete phase) movement. In this work the refer red solver is extended to take into account the elasticity of the polymer melts for the continuous phase. The solver capabilities will be illustrated by studying the effect of the fluid rheology on the filler dispersion, taking into account different fluid types (generalized Newtonian or viscoelastic) and particles volume fraction and size. The results obtained are used to evaluate the relevance of considering the fluid complex rheology for the prediction of the composites morphology

Viscoelastic properties of high pressure and heat induced tofu gels

Tofu gels were rheologically examined to determine their storage or elastic (G′) and loss or viscous (G″) moduli as a function of frequency within their linear viscoelastic limits. The tofu gels were made using either glucono-δ-lactone (GDL) or calcium sulphate (CaSO4·2H2O), followed by either heat treatment (heated soymilk at 97 °C prior to coagulation and subsequently held at 70 °C for 60 min, HT) or high pressure treatment (400 MPa at 20 °C for 10 min, HP). The overall moduli values of the GDL gels and CaSO4·2H2O gels of both physical treatments were similar, each gave frequency profiles expected for weak viscoelastic materials. However, although both temperature and high pressure treatments could be used to produce tofu gels, the final products were not the same. Pressure formed gels, despite having a higher overall “consistency” (increasing values of their moduli), had a proportionately higher contribution from the loss modulus (increased tan δ). Differences could also be observed using confocal scanning laser microscopy. While such treatment may give rise to differing systems/structures, with new or modified organoleptic properties, the more “open” structures obtained by pressure treatment may well cause processing difficulties if subsequent reworking or moulding is required.

Viscoelastic properties of high pressure and heat induced tofu gels

Tofu gels were rheologically examined to determine their storage or elastic (G') and loss or viscous (G '') moduli as a function of frequency within their linear viscoelastic limits. The tofu gels were made using either glucono-delta-lactone (GDL) or calcium sulphate (CaSO4 center dot 2H(2)O), followed by either heat treatment (heated soymilk at >= 97 degrees C prior to coagulation and subsequently held at 70 degrees C for 60 min, HT) or high pressure treatment (400 MPa at 20 degrees C for 10 min, HP). The overall moduli values of the GDL gels and CaSO4 center dot 2H(2)O gels of both physical treatments were similar, each gave frequency profiles expected for weak viscoelastic materials. However, although both temperature and high pressure treatments could be used to produce tofu gels, the final products were not the same. Pressure formed gels, despite having a higher overall "consistency" (increasing values of their moduli), had a proportionately higher contribution from the loss modulus (increased tan delta). Differences could also be observed using confocal scanning laser microscopy. While such treatment may give rise to differing systems/structures, with new or modified organoleptic properties, the more "open" structures obtained by pressure treatment may well cause processing difficulties if subsequent reworking or moulding is required. (c) 2007 Elsevier Ltd. All rights reserved.

Structure and viscoelastic behavior of pharmaceutical biocompatible anionic microemulsions containing the antitumoral drug compound doxorubicin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Rheological, mechanical and mucoadhesive properties of thermoresponsive, bioadhesive binary mixtures composed of poloxamer 407 and carbopol 974P designed as platforms for implantable drug delivery systems for use in the oral cavity

This study described the formulation and characterisation of the viscoelastic, mechanical and mucoadhesive properties of thermoresponsive, binary polymeric systems composed of poloxamer (P407) and poly(acrylic acid, C974P) that were designed for use as a drug delivery platform within the oral cavity. Monopolymeric and binary polymeric formulations were prepared containing 10, 15 and 20% (w/w) poloxamer (407) and 0.10-0.25% (w/w) poly(acrylic acid, 934P). The flow theological and viscoelastic properties of the formulations were determined using controlled stress and oscillatory rheometry, respectively, the latter as a function of temperature. The mechanical and mucoadhesive properties (namely the force required to break the bond between the formulation and a pre-hydrated mucin disc) were determined using compression and tensile analysis, respectively. Binary systems composed of 10% (w/w) P407 and C934P were elastoviscous, were easily deformed under stress and did not exhibit mucoadhesion. Formulations containing 15 or 20% (w/w) Pluronic P407 and C934P exhibited a sol-gel temperature T(sol/gel), were viscoelastic and offered high elasticity and resistance to deformation at 37 degrees C. Conversely these formulations were elastoviscous and easily deformed at temperatures below the sol-gel transition temperature. The sol-gel transition temperatures of systems containing 15% (w/w) P407 were unaffected by the presence of C934P; however, increasing the concentration of C934P decreased the T(sol/gel) in formulations containing 20%(w/w) P407. Rheological synergy between P407 and C934P at 37 degrees C was observed and was accredited to secondary interactions between these polymers, in addition to hydrophobic interactions between P407 micelles. Importantly, formulations composed of 20% (w/w) P407 and C934P exhibited pronounced mucoadhesive properties. The ease of administration (below the T(sol/gel)) in conjunction with the viscoelastic (notably high elasticity) and mucoadhesive properties (at body temperature) render the formulations composed of 20% (w/w) P407 and C934P as potentially useful platforms for mucoadhesive, controlled topical drug delivery within the oral cavity. (c) 2009 Published by Elsevier B.V.