Efeito do tratamento alcalino da fibra na resistência mecânica do compósito epóxi/capim-sapê

Due to growing concerns for reducing environmental damage caused by the use of non-renewable raw materials, there is a growing demand for research related to aggregate technology with environmental preservation. Thus, the use of non-renewable materials and less aggressive materials has been gaining attention. About composite materials, the exchange of synthetic fibers by natural fibers, especially vegetable fiber as reinforcement, has been increasing, due to its physical-chemical properties such as mechanical strength, nontoxic, low cost, low density, processing flexibility, non-abrasive to the process equipment, requiring simple surface treatments, etc. This objective was to process composites reinforced with long fibers of sapegrass in epoxy matrix and characterize the composites through mechanical tests. Three groups of composites were prepared according to the treatment received by the reinforcement: without treatment, alkali treatment at concentration of 5% w/v and alkali treatment at 10% w/v concentration. The materials were analyzed by tensile and flexural, and tests also optical microscopy and scanning electron microscopy (SEM). The results were statistically analyzed. As the main result, the alkali treatment of 5% in the sapegrass fibers increases the tensile and flexural strength, as a consequence of the improve adhesion between matrix and reinforcement

Incorporação da apatita na superfície da liga Ti30ta empregando tratamento alcalino associado à eletrofiação de fibras de PCL

Pós-graduação em Engenharia Mecânica - FEG

Efeito do tratamento das fibras nas propriedades do biocompósito de amido termoplástico/policaprolactona/sisal

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Crescimento de apatita na superfície da liga Ti-25Ta empregando dois tipos de tratamento de superfície: biomimético e deposição de polímero por eletrofiação

Titanium and its alloys has been widely used as materials for metallic biomaterials implants are usually employed to restore the hard tissue function, being used for artificial joints and bones, synthetic plates, crowns, dental implants and screws . Objective of this work was the surface modification of Ti-alloy 25Ta from biomimetic surface treatment of employment and deposition of polymer by electrospinning. The league was obtained from the fusion of the pure elements in the arc furnace with controlled atmosphere. The ingots were subjected to heat treatment, cold forged and sectioned discs with 13 mm diameter and 3 mm thick. Two surface treatments was evaluated, biomimetic and electrospinning with PCL fiber. The biomimetic treatment was performed involving alkaline treatment for three molarities 1.5M, 3M and 5M with immersion in SBF. The electrospinning was performed using PCL polymer alloy surface after the alkali treatment Ti25Ta 1M. For this group the polymer coated surfaces were immersed in calcium phosphate containing solution for immobilization of apatite. The results were compared with previous studies using surface treatment group to verify hydroxyapatite formation on the sample surface and it is concluded that the best condition is biomimetic treatment with 5M alkali treatment and heat treatment at 80 ° C for 72 hours

Pré-tratamento e hidrólise da casca de uva para liberação de açúcares fermentescíveis

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Reparo ósseo em scaffolds de TI6AL4V sinterizados pela tecnologia de sinterização direta de metais a laser (DMLS) submetidos a tratamento de superfície associado à aplicação de ultrassom de baixa intensidade (LIPUS)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização da liga Ti-30Ta após tratamento biomimético associado à incorporação de antibiótico

Surface treatments have been used to modify the surface of titanium alloys. The purpose of this study is to evaluate the surface of Ti-30Ta alloy after biomimetic approach associated to antibiotic incorporation. The ingots were obtained in arc melting furnace, treated and cold-worked by swaging. The surface treatment was performed in two steps: biomimetic treatment and antibiotic incorporation. For biomimetic treatment, first an alkaline treatment (NaOH 1M at 60ºC) was performed, followed by heat treatment and immersion in SBFx5 (Simulated Body Fluid) for a period of 24 hours. In order to incorporate the antibiotic, samples were immersed in a solution formed by drugs plus SBFx5 for 48 hours. The sample surfaces were analyzed by scanning electron microscopy (SEM), X-Ray diffraction (XRD), atomic force microscopy (AFM) and contact angle measurements. The release of antibiotic from coated implants was measured in phosphate buffer saline at pH 7.4 by using UV/VIS spectrometry. Results have shown changes on the surface after incorporating the drug, which is gradually co-precipitated with the Ca-P crystals, forming a uniform and rough layer on the metal surface

Caracterização da liga Ti-30Ta após tratamento biomimético associado à incorporação de antibiótico

Surface treatments have been used to modify the surface of titanium alloys. The purpose of this study is to evaluate the surface of Ti-30Ta alloy after biomimetic approach associated to antibiotic incorporation. The ingots were obtained in arc melting furnace, treated and cold-worked by swaging. The surface treatment was performed in two steps: biomimetic treatment and antibiotic incorporation. For biomimetic treatment, first an alkaline treatment (NaOH 1M at 60ºC) was performed, followed by heat treatment and immersion in SBFx5 (Simulated Body Fluid) for a period of 24 hours. In order to incorporate the antibiotic, samples were immersed in a solution formed by drugs plus SBFx5 for 48 hours. The sample surfaces were analyzed by scanning electron microscopy (SEM), X-Ray diffraction (XRD), atomic force microscopy (AFM) and contact angle measurements. The release of antibiotic from coated implants was measured in phosphate buffer saline at pH 7.4 by using UV/VIS spectrometry. Results have shown changes on the surface after incorporating the drug, which is gradually co-precipitated with the Ca-P crystals, forming a uniform and rough layer on the metal surface

Aplicação de zeólitos hierárquicos a reacções de acilação de Friedel-Crafts

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química

Produção de biocombustíveis a partir da biomassa : melhoria da resistência do zeólito ZSM-5 aos compostos fenólicos

Dissertação para obtenção do Grau de Mestre em Engenharia Química e Bioquímica

Estabilidade aeróbia, pH e dinâmica de desenvolvimento de microrganismos da cana-de-açúcar in natura hidrolisada com cal virgem

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Processamento da cana-de-açúcar: efeitos sobre a digestibilidade, o consumo e a taxa de passagem

O objetivo neste trabalho foi estudar o efeito do tratamento alcalino da cana-de-açúcar com hidróxido de sódio (1,5 a 50% de NaOH) sobre a digestibilidade total e o consumo de matéria seca das dietas experimentais e as taxas de passagem das canas-de-açúcar. Foram utilizados quatro bovinos mestiços (Zebu x Holandês) alimentados com canas-de-açúcar in natura, hidrolisada, hidrolisada fenada e hidrolisada ensilada como fontes volumosas, constituindo 70% das dietas. O tratamento alcalino foi mais eficiente na fração fibra, proporcionando aumentos de pelo menos 45% na digestibilidade. Os aumentos de 25,0 e 16,7% no consumo das dietas contendo as cana-de-açúcar hidrolisada (1,5% PV) e hidrolisada fenada (1,4% PV) provavelmente foram influenciados pela maior digestibilidade da fibra. Os valores estimados de taxa de passagem ruminal no ceco-cólon e o tempo de retenção em cada compartimento não diferiram entre as cana-de-açúcar in natura, hidrolisada e hidrolisada fenada. Entretanto, para a cana-de-açúcar hidrolisada ensilada, observaram-se as menores taxas (1,5 e 7,4%/h) e o maior tempo de retenção (71,4 horas). Concluiu-se que o tratamento alcalino com hidróxido de sódio, com ou sem fenação, melhorou a digestão da fibra da cana-de-açúcar no trato digestivo total e proporcionou acréscimo do consumo de matéria seca da cana-de-açúcar hidrolisada, sem afetar a taxa de passagem. Entretanto, a posterior ensilagem pode não trazer esses benefícios.

Hidrólise da cana-de-açúcar com cal virgem ou cal hidratada

Objetivou-se estudar o efeito do tratamento alcalino da cana-de-açúcar com cal virgem ou cal hidratada sobre a composição bromatológica e a digestibilidade in vitro da matéria seca, da fibra em detergente neutro e da fibra em detergente ácido. Utilizou-se um delineamento inteiramente casualizado em esquema fatorial 3 × 3, composto de três formas de processamento da cana (in natura; cana hidrolisada com 0,5% de cal virgem; e cana hidrolisada com 0,5% de cal hidratada) e três tempos de armazenamento (12, 36 e 60 horas). As formas de processamento influenciaram os teores de matéria orgânica, matéria mineral, carboidratos totais e hemicelulose, assim como os teores de fibra em detergente neutro e nutrientes digestíveis totais. Os tempos de armazenamento influenciaram os teores de proteína bruta, matéria orgânica, carboidratos totais e hemicelulose. Entre os minerais, somente o teor de cálcio teve aumento com a inclusão de ambos os tipos de cal em relação à cana-de-açúcar, que não sofreu o processo de hidrólise. Os coeficientes de digestibilidade da matéria seca e da fibra em detergente neutro aumentaram com a hidrólise da cana em comparação à cana in natura. A hidrólise com cal hidratada ou com cal virgem mantém o valor nutricional da cana-de-açúcar, permitindo que possa ser utilizada depois de até 60 horas de armazenamento.

Morfologia e propriedades mecânicas da fibra de sisal unidirecional e em sobreposição de compósito com resina epóxi

The composites manufactured with long fibres aligned in a single direction, and overlay has been shown to have better performance than the short fibers randomly distributed. In particular, the lignocellulosic fibers extracted from the sisal leaves, used in conjunction with the epoxy resin has attracted the attention of many researchers because the final properties of the system formed. In this work composites based on epoxy resin reinforced with sisal fibers were manufactured. The sisal fibres were treated with an alkaline solution of 0.06 mol/l NaOH. The treated, and untreated fibres were subjected to tension x extension tests. The composites were manufactured in the "Lossy" mold with the specifications of the samples to be produced (300x20x4 mm). The tension tests were carried out in accordance with the ASTM standards 3039 (for the composite aligned in a single direction) and ASTM D5573 (for composites in overlay), three point bending tests were performed according to ASTM D790. Analyzing the results of the tests of tension and three point bending tests, it was observed that the composites with the configuration of overlapping had the better elastic module in both tests. As to the maximum resistance to tension, the best result was the composites aligned in a single direction. Tests of absorption of water and micrographs are in progress

Palma forrageira (Opuntia ficus indica e Nopalea cochenillifera) como matéria-prima para produção de etanol celulósico e enzimas celulolíticas

The need for new sources of energy and the concern about the environment have pushed the search for renewable energy sources such as ethanol. The use of lignocellulosic biomass as substrate appears as an important alternative because of the abundance of this raw material and for it does not compete with food production. However, the process still meets difficulties of implementation, including the cost for production of enzymes that degrade cellulose to fermentable sugars. The aim of this study was to evaluate the behavior of the species of cactus pear Opuntia ficus indica and Nopalea cochenillifera, commonly found in northeastern Brazil, as raw materials for the production of: 1) cellulosic ethanol by simultaneous saccharification and fermentation (SSF) process, using two different strains of Saccharomyces cerevisiae (PE-2 and LNF CA-11), and 2) cellulolytic enzymes by semi-solid state fermentation (SSSF) using the filamentous fungus Penicillium chrysogenum. Before alcoholic fermentation process, the material was conditioned and pretreated by three different strategies: alkaline hydrogen peroxide, alkaline using NaOH and acid using H2SO4 followed by alkaline delignification with NaOH. Analysis of composition, crystallinity and enzymatic digestibility were carried out with the material before and after pretreatment. In addition, scanning electron microscopy images were used to compare qualitatively the material and observe the effects of pretreatments. An experimental design 2² with triplicate at the central point was used to evaluate the influence of temperature (30, 40 and 45 °C) and the initial charge of substrate (3, 4 and 5% cellulose) in the SSF process using the material obtained through the best condition and testing both strains of S. cerevisiae, one of them flocculent (LNF CA-11). For cellulase production, the filamentous fungus P. chrysogenum was tested with N. cochenillifera in the raw condition (without pretreatment) and pretrated hydrothermically, varying the pH of the fermentative medium (3, 5 and 7). The characterization of cactus pear resulted in 31.55% cellulose, 17.12% hemicellulose and 10.25% lignin for N. cochenillifera and 34.86% cellulose, 19.97% hemicellulose and 15.72% lignin for O. ficus indica. It has also been determined, to N. cochenillifera and O. ficus indica, the content of pectin (5.44% and 5.55% of calcium pectate, respectively), extractives (26.90% and 9.69%, respectively) and ashes (5.40% and 5.95%). Pretreatment using alkaline hydrogen peroxide resulted in the best cellulose recovery results (86.16% for N. cochenillifera and 93.59% for O. ficus indica) and delignification (48.79% and 23.84% for N. cochenillifera and O. ficus indica, respectively). This pretreatment was also the only one which did not increase the crystallinity index of the samples, in the case of O. ficus indica. However, when analyzing the enzymatic digestibility of cellulose, alkali pretreatment was the one which showed the best yields and therefore it was chosen for the tests in SSF. The experiments showed higher yield of conversion of cellulose to ethanol by PE-2 strain using the pretreated N. cochenillifera (93.81%) at 40 °C using 4% initial charge of cellulose. N. cochenillifera gave better yields than O. ficus indica and PE-2 strain showed better performance than CA-11. N. cochenillifera proved to be a substrate that can be used in the SSSF for enzymes production, reaching values of 1.00 U/g of CMCase and 0.85 FPU/g. The pretreatment was not effective to increase the enzymatic activity values