Systemvergleich zwischen magnetisch erregten und piezoerregten Schwingförderern

Energieeffizienz und Leistungsfähigkeit von fördertechnischen Anlagen sind in den vergangenen Jahren immer mehr in den Fokus der Betreiber und Hersteller gerückt. Im Rahmen einer Untersuchung am Fraunhofer-Institut für Materialfluss und Logistik IML wurden diese beiden Aspekte an magnetisch erregten und piezoerregten Schwingförderern untersucht. Ein Systemvergleich stellt dabei die wesentlichen Vor- und Nachteile der jeweiligen Antriebsart dar und unterstützt sowohl bei der Auswahl als auch bei der Optimierung von Transportsystemen im logistischen Umfeld.

Wide area control of SVCs for first swing stabilisation and damping in longitudinal systems

A non-linear Kalman filter based control strategy for SVCs located in major load groups is presented. This focusses on the limitation and damping of inter-area modes. It does this through treating local modes as noise and uses a tunable nonlinear control algorithm to improve both first swing stability and system damping. Simulation on a four machine system shows that the Kalman filer can successfully lock on to a desired inter-area mode and obtain a 31% improvement in critical clearing time as well as improved damping.

Dragline swing automation

Draglines are used extensively for overburden stripping in Australian open cut coal mines. This paper outlines the design of a computer control system to implement an automated swing cycle on a production dragline. Subsystems and sensors have been developed to satisfy the constraints imposed by the task, the harsh operating environment and the mine's production requirements.

Swing load stabilization for mining and construction applications

This paper discusses the issue of sensing and control for stabilizing a swinging load. Our work has focused in particular on the dragline as used for overburden stripping in open-pit coal mining, but many of the principles would also be applicable to construction cranes. Results obtained from experimental work on a full-scale production dragline are presented.

Dragline swing automation

Draglines are very large machines that are used to remove overburden in open-cut coal mines. This paper outlines the design of a computer control system to implement an automated swing cycle on a production dragline. Subsystems and sensors have been developed to satisfy the constraints imposed by the task, the harsh operating environment and the mine's production requirements.

Case study: Dragline swing to dump automation

Dragline Swing to Dump Automation By Peter Corke, CSIRO Manufacturing Technology/CRC for Mining Technology and Equipment (CMTE) Peter Corke presented a case study of a project to automate the dragline swing to dump operation. The project is funded by ACARP, BHP Coal, Pacific Coal and the CMTE and is being carried out on a dragline at Pacific Coal's Meandu mine near Brisbane. Corke began by highlighting that the minerals industry makes extensive use of large, mechanised machines. However, unlike other industries, mining has not adopted automation and most machines are controlled by human operators on board the machine itself. Choosing an automation target The dragline automation was chosen because: ò draglines are one of the biggest capital assets in a mine; ò performance between operators vary significantly, so improved capital utilisation is possible; ò the dragline is often the bottleneck in production; ò a large part of the operation cycle is spent swinging from dig to dump; and ò it is technically feasible. There has been a history of drag line automation projects, none with great success.

Swing Low

From Kurt Vonnegut to Stephen King, many novelists use metanarrative techniques to insert fictional versions of themselves in the stories they tell. The function of deploying such techniques is often to draw attention to the liminal space between the fictional constructs inherent in the novel as a form, and the real world from which the constructs draw inspiration, and indeed, are read by an audience. For emerging writers working in short form narratives, however, the structural demands of the short story or flash fiction make the use of similar techniques problematic in the level of depth to which they can be deployed. ‘Swing Low’ is the fifth in a series of short stories that work to overcome the structural limitations of a succinct form by developing a fractured fictional version of the author over a number of pieces and published across a range of sites. The accumulative affect is a richer metanarrative textual arrangement that also allows for the individual short stories to function independently.

Swing amplification of nonaxisymmetric perturbations in stars and gas in a sheared galactic disk

We present a study of the growth of local, nonaxisymmetric perturbations in gravitationally coupled stars and gas in a differentially rotating galactic disk. The stars and gas are treated as two isothermal fluids of different velocity dispersions, with the stellar velocity dispersion being greater than that for the gas. We examine the physical effects of inclusion of a low-velocity dispersion component (gas) on the growth of non-axisymmetric perturbations in both stars and gas, as done for the axisymmetric case by Jog & Solomon. The amplified perturbations in stars and gas constitute trailing, material, spiral features which may be identified with the local spiral features seen in all spiral galaxies. The formulation of the two-fluid equations closely follows the one-fluid treatment by Goldreich & Lynden-Bell. The local, linearized perturbation equations in the sheared frame are solved to obtain the results for a temporary growth via swing amplification. The problem is formulated in terms of five dimensionless parameters-namely, the Q-factors for stars and gas, respectively; the gas mass fraction; the shearing rate in the galactic disk; and the length scale of perturbation. By using the observed values of these parameters, we obtain the amplifications and the pitch angles for features in stars and gas for dynamically distinct cases, as applicable for different regions of spiral galaxies. A real galaxy consisting of stars and gas may display growth of nonaxisymmetric perturbations even when it is stable against axisymmetric perturbations and/or when either fluid by itself is stable against non-axisymmetric perturbations. Due to its lower velocity dispersion, the gas exhibits a higher amplification than do the stars, and the amplified gas features are slightly more tightly wound than the stellar features. When the gas contribution is high, the stellar amplification and the range of pitch angles over which it can occur are both increased, due to the gravitational coupling between the two fluids. Thus, the two-fluid scheme can explain the origin of the broad spiral arms in the underlying old stellar populations of galaxies, as observed by Schweizer and Elmegreen & Elmegreen. The arms are predicted to be broader in gas-rich galaxies, as is indeed seen for example in M33. In the linear regime studied here, the arm contrast is shown to increase with radius in the inner Galaxy, in agreement with observations of external galaxies by Schweizer. These results follow directly due to the inclusion of gas in the problem.

Pillar height dependent formation of unprecedented Pd-8 molecular swing and Pd-6 molecular boat via multicomponent self-assembly

Three-component self-assembly of a cis-blocked 90 degrees Pd(II) acceptor with a mixture of a tetraimidazole and a linear dipyridyl donor self-discriminated into unusual Pd-8 molecular swing (1) and Pd-6 molecular boat (2), which are characterized by single-crystal X-ray diffraction analysis; their ability to bind C-60 in solution is established by fluorescence titration.

Comparison between weight loss of bends in a pneumatic conveyor and erosion rate obtained in a centrifugal erosion tester for the same materials

In order to find a link between results obtained from a laboratory erosion tester and tests carried out on a pneumatic conveyor, a comparison has been made between weight loss from bends on an industrial-scale pneumatic conveyor and erosion rates obtained in a small centrifugal erosion tester, for the same materials. Identical test conditions have been applied to both experiments so that comparable test results have been obtained. The erosion rate of mild steel commonly used as the wall material of conveyor pipes and pipe bends was determined individually on both test rigs. A relationship between weight loss from the bends and erosion rate determined from the tester has been developed. A discussion based on the results and their applicability to the prediction of wear in pneumatic conveyors concludes the paper. © 2004 Elsevier B.V. All rights reserved.

Determinación de la actividad radicular del Lima tahiti citrus aurantifolia (christm,) swing, mediante la variación de almacenamiento del agua del suelo, utilizando técnicas nucleares

Con el objetivo de determinar la actividad radicular y el patrón de distribución de las raíces activas del lima Tahití Citrus aurantifolia (Christm.) Swing., mediante la variación de almacenamiento de agua del suelo utilizando técnicas nucleares, se condujo un experimento en la finca San Bernardo, municipio de Masatepe, Departamento de Masaya. Se escogieron plantas de la misma edad, pureza varietal, características vegetativas uniformes y se establecieron en cada unidad experimental 4 tratamientos (50, 100, 150,200 cm de distancia del tronco), por 2 repeticiones para un total de 16 observaciones y se cubrió con plástico de polietileno negro en un área de 19.63 m2 que corresponde a un circulo de radio igual a 250 cm del tronco a cada árbol. En la época seca se tomaron lecturas, y la información obtenida y analizada permite concluir que en árboles de limón Tahití de 6 años de edad, y en las condiciones edafoclimáticas y de manejo del cultivo en que se llevó el experimento, presenta su actividad radicular directamente proporcional a las distancias horizontales del tronco del árbol, mediante el consumo total de agua en el volumen de suelo (O - 90 cm de profundidad), y a la vez directamente proporcional cada 30 cm de profundidad para un perfil de suelo de (O - 90 cm de profundidad), lo que indica presencia de un sistema radicular extenso y profundo.