Machined and plastic copings in three-element prostheses with different types of implant-abutment joints: a strain gauge comparative analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparative Strain Gauge Analysis of External and Internal Hexagon, Morse Taper, and Influence of Straight and Offset Implant Configuration

Purpose: The present study was designed to analyze strain distributions caused by varying the fixture-abutment design and fixture alignment.Materials and Methods: Three implants of external, internal hexagon, and Morse taper were embedded in the center of each polyurethane block in straight placement and offset placement. Four strain gauges (SGs) were bonded on the surface of polyurethane block, which was designated SG1 placed mesially adjacent to implant A, SG2 and SG3 were placed mesially and distally adjacent to the implant B and SG4 was placed distally adjacent to the implant C. The 30 superstructures' occlusal screws were tightened onto the Microunit abutments with a torque of 10 N cm using the manufacturers' manual torque-controlling device.Results: There were statistically significant differences in prosthetic connection (P value = 0.0074 < 0.5). There were no statistically significant differences in placement configuration/alignment (P value = 0.7812 > 0.5).Conclusion: The results showed fundamental differences in both conditions. There was no evidence that there was any advantage to offset implant placement in reducing the strain around implants. The results also revealed that the internal hexagon and Morse taper joints did not reduce the microstrain around implants. (Implant Dent 2011; 20:e24-e32)

External Hexagon and Internal Hexagon in Straight and Offset Implant Placement: Strain Gauge Analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Straight and Offset Implant Placement under Axial and Nonaxial Loads in Implant-Supported Prostheses: Strain Gauge Analysis

Purpose: The aim of this in vitro study was to quantify strain development during axial and nonaxial loading using strain gauge analysis for three-element implant-supported FPDs, varying the arrangement of implants: straight line (L) and offset (O). Materials and Methods: Three Morse taper implants arranged in a straight line and three implants arranged in an offset configuration were inserted into two polyurethane blocks. Microunit abutments were screwed onto the implants, applying a 20 Ncm torque. Plastic copings were screwed onto the abutments, which received standard wax patterns cast in Co-Cr alloy (n = 10). Four strain gauges were bonded onto the surface of each block tangential to the implants. The occlusal screws of the superstructure were tightened onto microunit abutments using 10 Ncm and then axial and nonaxial loading of 30 Kg was applied for 10 seconds on the center of each implant and at 1 and 2 mm from the implants, totaling nine load application points. The microdeformations determined at the nine points were recorded by four strain gauges, and the same procedure was performed for all of the frameworks. Three loadings were made per load application point. The magnitude of microstrain on each strain gauge was recorded in units of microstrain (mu). The data were analyzed statistically by two-way ANOVA and Tukey's test (p < 0.05). Results: The configuration factor was statistically significant (p= 0.0004), but the load factor (p= 0.2420) and the interaction between the two factors were not significant (p= 0.5494). Tukey's test revealed differences between axial offset (mu) (183.2 +/- 93.64) and axial straight line (285.3 +/- 61.04) and differences between nonaxial 1 mm offset (201.0 +/- 50.24) and nonaxial 1 mm straight line (315.8 +/- 59.28). Conclusion: There was evidence that offset placement is capable of reducing the strain around an implant. In addition, the type of loading, axial force or nonaxial, did not have an influence until 2 mm.

Numerical simulations of void growth near a notch tip in ductile single crystals

The objective of this work is to study the growth of a cylindrical void ahead of a notch tip in ductile FCC single crystals under mode I, plane strain, small scale yielding (SSY) conditions. To this end, finite element simulations are performed within crystal plasticity framework neglecting elastic anisotropy. Attention is focussed on the effects of crystal hardening, ratio of void diameter to spacing from the notch and crystal orientation on plastic flow localization in the ligament connecting the notch and the void as well as their growth. The results show strong interaction between shear bands emanating from the notch and angular sectors of single slip forming around the void leading to intense plastic strain development in the ligament. Further, the ductile fracture processes are retarded by increase in hardening of the single crystal and decrease in ratio of void diameter to spacing from the notch. Also, a strong influence of crystal orientation on near-tip void growth and plastic slip band development is observed. Finally, the synergistic, cooperative growth of multiple voids ahead of the notch tip is examined.

Febrifugine derivative antimalarial activity: quantum mechanical predictors

O desenvolvimento de linhagens resistentes de Plasmodium falciparum tem encorajado a busca por novas drogas antimalariais. A febrifugina é uma substância natural com alta atividade contra o P. falciparum que apresenta propriedade emética e toxicidade para o fígado tal que não permitem o seu uso clínico. A busca por análogos que possam ter uma performance clínica melhor é um tema de pesquisa atual. Nosso objetivo é investigar a estrutura eletrônica teórica de uma família de derivados da febrifugina empregando cálculos semi-empíricos de orbitais moleculares, procurando por índices eletrônicos que possam ajudar a modelar novos derivados mais eficientes. Os resultados teóricos mostram que para as moléculas mais seletivas existe um agrupamento dos valores de determinados índices em intervalos bem definidos. O modelo proposto para se obter alta seletividade foi testado com sucesso.

Extensometria: estudo das microdeformações ao redor de três implantes de hexágono interno, com posicionamento linear, sob a influência da fundição de coifas plásticas e usinadas

The objective of this in vitro study was quantify the micro strain development around the internal hexagon implants, varying the type of prosthetic coping. For This reason, three implants of internal hexagon were inserted into one polyurethane block in line placement. Microunit abutments were screwed onto the implants. Tangentially the implants were bonded the strain gauges, two to the center implant. Ten structures, each one containing three copings were cast in Co-Cr alloy, that were divided into groups in the first group, plastic copings were used, and in the second group machined copings were used. The superstructure’s occlusal screws were tightened onto Microunit abutments with 10 Ncm torque, the magnitude of micro strain was recorded. The mean values of each strain gauge of each plastic copings were 363,37 ± 237,66 and the machined copings were 338,12 ± 223,01. The data were analyzed statistically by t- Student test. No statistically significant difference was found between the prosthetic copings (p= 0,867). It was concluded that to internal hexagon implants in line placement, the type of copings presented similar magnitude of micro strain after prosthetic occlusal screw was tightened

Analyse des Ermüdungsverhaltens von Beton anhand der Dehnungsentwicklung

Die Weiterentwicklungen in der Betontechnologie führten in den letzten Jahrzehnten zu Hochleistungsbetonen mit immer höheren Festigkeiten. Der Ermüdungsnachweis wurde jedoch kaum weiterentwickelt und beinhaltet immer noch sehr grobe Herangehensweisen bei der Berücksichtigung des Materialwiderstands von Beton. Für eine grundlegende Weiterentwicklung dieses Nachweises fehlt noch das notwendige Wissen zu den Mechanismen der Betonermüdung. Das Ziel dieser Arbeit war es daher, grundlegende Erkenntnisse zum Ermüdungsverhalten hochfester Betone bei unterschiedlichen zyklischen Beanspruchungen zu ermitteln und hierdurch zu einem besseren Verständnis der Mechanismen der Betonermüdung beizutragen. In der vorliegenden Arbeit wurde das Ermüdungsverhalten eines hochfesten Betons bei Druckschwellbeanspruchung anhand der Dehnungs- und Steifigkeitsentwicklungen untersucht. Betrachtet wurden dabei die Einflüsse der bezogenen Oberspannung, der Belastungsfrequenz und der Wellenform. Zusätzlich wurden, ausgehend von in der Literatur dokumentierten Ansätzen, Versuche bei monoton steigender Beanspruchung und Dauerstandbeanspruchung vergleichend durchgeführt. Die Dehnungs- und Steifigkeitsentwicklungen werden durch die untersuchten Belastungsparameter der Ermüdungsbeanspruchung eindeutig beeinflusst. Charakteristische Zusammenhänge zwischen der Beeinflussung einzelner Kenngrößen der Dehnungs- und Steifigkeitsentwicklung und der Beeinflussung der Bruchlastwechselzahlen wurden aufgezeigt. Anhand der Dehnungen und Steifigkeiten an den Phasenübergängen konnten Hinweise auf beanspru-chungsartabhängige Gefügezustände abgeleitet werden. Die vergleichende Auswertung des Dehnungsverhaltens bei monoton steigender Beanspruchung, Ermüdungsbeanspruchung und Dauerstandbeanspruchung zeigte, dass das Ermüdungsverhalten von Beton nicht adäquat in Anlehnung an andere Beanspruchungsarten beschrieben werden kann. Die Untersuchungsergebnisse wurden in eine Modellvorstellung übertragen, die zur Beurteilung der baustofflichen Phänomene bei zyklischen Beanspruchungen geeignet ist. Dabei wurde die Hypothese aufgestellt, dass sich unterschiedlich ausgeprägte Kleinst-Gefügeveränderungen beanspruchungsabhängig einstellen, die die Entstehung und Ausbreitung von Mikrorissen beeinflussen. Die detaillierte Untersuchung der Dehnungs- und Steifigkeitsentwicklungen führte zu neuen und tiefergehenden Erkenntnissen und sollte ergänzt durch die Betrachtungen von Gefügezuständen zukünftig weiterverfolgt werden.

Impact of previous hamstring strain injury on rate of torque and EMG development during eccentric contraction.

Background: Hamstring strain injuries (HSIs) are prevalent in sport and re-injury rates have been high for many years. Whilst much focus has centred on the impact of previous hamstring strain injury on maximal eccentric strength, high rates of torque development is also of interest, given the important role of the hamstrings during the terminal swing phase of gait. The impact of prior strain injury on neuromuscular function of the hamstrings during tasks requiring high rates of torque development has received little attention. The purpose of this study is to determine if recreational athletes with a history of unilateral hamstring strain injury, who have returned to training and competition, will exhibit lower levels of eccentric muscle activation, rate of torque development and impulse 30, 50 and 100ms after the onset of electromyographical or torque development in the previously injured limb compared to the uninjured limb. Methods: Twenty-six recreational athletes were recruited. Of these, 13 athletes had a history of unilateral hamstring strain injury (all confined to biceps femoris long head) and 13 had no history of hamstring strain injury. Following familiarisation, all athletes undertook isokinetic dynamometry testing and surface electromyography assessment of the biceps femoris long head and medial hamstrings during eccentric contractions at -60 and -1800.s-1. Results: In the injured limb of the injured group, compared to the contralateral uninjured limb rate of torque development and impulse was lower during -600.s-1 eccentric contractions at 50 (RTD, p=0.008; IMP, p=0.005) and 100ms (RTD, p=0.001; IMP p<0.001) after the onset of contraction. There was also a non-significant trend for rate of torque development during -1800.s-1 to be lower 100ms after onset of contraction (p=0.064). Biceps femoris long head muscle activation was lower at 100ms at both contraction speeds (-600.s-1, p=0.009; -1800.s-1, p=0.009). Medial hamstring activation did not differ between limbs in the injured group. Comparisons in the uninjured group showed no significant between limbs difference for any variables. Conclusion: Previously injured hamstrings displayed lower rate of torque development and impulse during eccentric contraction. Lower muscle activation was confined to the biceps femoris long head. Regardless of whether these deficits are the cause of or the result of injury, these findings have important implications for hamstring strain injury and re-injury and suggest greater attention be given to neural function of the knee flexors.

Shaping development through mechanical strain: The transcriptional basis of diet-induced phenotypic plasticity in a cichlid fish

Adaptive phenotypic plasticity, the ability of an organism to change its phenotype to match local environments, is increasingly recognized for its contribution to evolution. However, few empirical studies have explored the molecular basis of plastic traits. The East African cichlid fish Astatoreochromis alluaudi displays adaptive phenotypic plasticity in its pharyngeal jaw apparatus, a structure that is widely seen as an evolutionary key innovation that has contributed to the remarkable diversity of cichlid fishes. It has previously been shown that in response to different diets, the pharyngeal jaws change their size, shape and dentition: hard diets induce an adaptive robust molariform tooth phenotype with short jaws and strong internal bone structures, while soft diets induce a gracile papilliform tooth phenotype with elongated jaws and slender internal bone structures. To gain insight into the molecular underpinnings of these adaptations and enable future investigations of the role that phenotypic plasticity plays during the formation of adaptive radiations, the transcriptomes of the two divergent jaw phenotypes were examined. Our study identified a total of 187 genes whose expression differs in response to hard and soft diets, including immediate early genes, extracellular matrix genes and inflammatory factors. Transcriptome results are interpreted in light of expression of candidate genesmarkers for tooth size and shape, bone cells and mechanically sensitive pathways. This study opens up new avenues of research at new levels of biological organization into the roles of phenotypic plasticity during speciation and radiation of cichlid fishes.

Design and development of Fiber Bragg Grating sensing plate for plantar strain measurement and postural stability analysis

This paper describes an ab initio design and development of a novel Fiber Bragg Grating (FBG) sensor based strain sensing plate for the measurement of plantar strain distribution in human foot. The primary aim of this work is to study the feasibility of usage of FBG sensors in the measurement of plantar strain in the foot; in particular, to spatially resolve the strain distribution in the foot at different regions such as fore-foot, mid-foot and hind-foot. This study also provides a method to quantify and compare relative postural stability of different subjects under test; in addition, traditional accelerometers have been used to record the movements of center of gravity (second lumbar vertebra) of the subject and the results obtained have been compared against the outcome of the postural stability studies undertaken using the developed FBG plantar strain sensing plate. (C) 2013 Elsevier Ltd. All rights reserved.

Temperature- and salinity-dependent development of a Nordic strain of Ichthyophthirius multifiliis from rainbow trout

During the twentieth century evidence was presented which suggested the presence of various strains and races of the parasite Ichthyophthirius multifiliis Fouquet. However, ecological profiles of various parasite isolates from different climatic zones are sparse. Such stringent characterizations of parasite development at defined abiotic conditions could provide valuable criteria for the different races: profile comparison from various localities is one way to differentiate these strains. Baseline investigations were therefore performed on the associations between abiotic factors (temperature/salinity) and the development of theronts in tomocysts of I. multifiliis isolated from rainbow trout in a Danish trout farm. It was shown that tomocyst formation and theront development took place between 5 and 30degreesC. Development rates and sizes of theronts were clearly affected by temperature: theronts escaped tomocysts already after 16-27 h at 25degreesC and 30degreesC, whereas this process took 8-9 days at 5degreesC. Likewise, theront size decreased steadily from a maximum of 57.4 x 28.6 mum at 5degreesC to 28.6 x 20.0 mum at 30degreesC. This size variation was only partly associated with the number of theronts that appeared at different temperatures. The lowest number of theronts escaping from one tomocyst was indeed found at 5-7degreesC (mean 329-413). At 11.6, 17.0 and 21degreesC. the highest number of theronts appeared (mean 546-642). However, at 25 and 30degreesC, the number decreased (458 and 424, respectively). Additional studies on the salinity dependent development of the parasite (at 11.6degreesC) showed that salinities above 5 p.p.t. totally inhibited development. Even at 5 p.p.t. the developmental time significantly increased and the number of theronts produced from one tomocyst decreased.