Determinação altimétrica através do sistema de posicionamento global

Este estudo tem por objetivo verificar a influência do tempo de coleta de dados com receptores GPS nas determinações altimétricas. O levantamento altimétrico é realizado através do método de posicionamento relativo estático, utilizando dois receptores GPS de uma freqüência, em diferentes tempos de ocupação (30, 15, 10 e 5 minutos) com uma taxa de gravação de dois segundos. As altitudes obtidas com receptores GPS são comparadas com as altitudes determinadas por nivelamento trigonométrico com Estação Total. Os resultados mostraram que os tempos de ocupação menores que 30 minutos (15, 10 e 5 minutos) também são adequados para a obtenção de diferenças centimétricas nas altitudes analisadas. Mesmo considerando a precisão dos métodos topográficos convencionais, este estudo demonstra a possibilidade da utilização do Sistema de Posicionamento Global (GPS) de forma precisa nos levantamentos altimétricos, desde que se efetue a modelagem da ondulação geoidal.

Use of GPS for Photogrammetry, HR-342, 1993

Five test flights were conducted to study the use of Global Positioning System (GPS) in Photogrammetry, three in Iowa, one each in California and Texas. These tests show that GPS can be used to establish ground control by the static method and to determine camera location by the kinematic method. In block triangulation, six GPS controls are required and additional elevation control along the centerline is also required in strip triangulation. The camera location determined by aerial triangulation depends on the scale of the photography. The 1:3000 scale photography showed that the absolute accuracy of the camera location by GPS is better than five centimeters. The 1:40000 scale photography showed that the relative accuracy of the camera location by GPS is about one millimeter. In a strip triangulation elevation control is required in addition to the camera location by GPS. However, for block triangulation camera location by GPS is sufficient. Pre-targeting of pass and tie points gives the best results in both block and strip triangulation. In normal mapping for earth work computations the use of 1:6000 scale photography with GPS control instead of 1:3000 scale is recommended. It is recommended that research be done in the use of GPS for navigation in aerial photographic missions. It is highly recommended that research be done in the use of GPS to determine tip and tilt of the aerial camera, that is required in stereoplotting.

Changes in test scores distribution for students of the fourth grade in Brazil: a relative distribution analysis for the years 1997 to 2005

To assess the quality of school education, much of educational research is concerned with comparisons of test scores means or medians. In this paper, we shift this focus and explore test scores data by addressing some often neglected questions. In the case of Brazil, the mean of test scores in Math for students of the fourth grade has declined approximately 0,2 standard deviation in the late 1990s. But what about changes in the distribution of scores? It is unclear whether the decline was caused by deterioration in student performance in upper and/or lower tails of the distribution. To answer this question, we propose the use of the relative distribution method developed by Handcock and Morris (1999). The advantage of this methodology is that it compares two distributions of test scores data through a single distribution and synthesizes all the differences between them. Moreover, it is possible to decompose the total difference between two distributions in a level effect (changes in median) and shape effect (changes in shape of the distribution). We find that the decline of average-test scores is mainly caused by a worsening in the position of all students throughout the distribution of scores and is not only specific to any quantile of distribution.

Comportamento higroscópico da farinha de pupunha (Bactris gasipaes)

Avaliou-se o comportamento higroscópico da farinha de pupunha obtida por secagem em estufa a 70°C. Obteve-se dados de equilíbrio de adsorção de umidade a 15°C e 35°C, através de um método estático, onde recipientes de 500mL, contendo soluções saturadas de sais, foram utilizados como ambientes geradores de umidades relativas constantes, na faixa de 11% a 97%, aos quais foram submetidas amostras do produto. A partir dos dados de equilíbrio foram construídas isotermas de adsorção de umidade, sendo observadas isotermas do tipo III e, ainda, que a umidade de equilíbrio diminui com o aumento da temperatura. Determinou-se o calor isostérico de adsorção para diferentes níveis de umidade de equilíbrio e a umidade equivalente à monocamada, observando-se valores inferiores a 5g H₂O/100 g s.s. Verificou-se a aplicabilidade do modelo GAB na predição de dados de equilíbrio do produto. De acordo com os resultados obtidos, a farinha de pupunha apresenta baixa higroscopicidade, ou seja, baixa afinidade por moléculas de água.

Isotermas de dessorção de filé de bonito (Sarda sarda) desidratado osmoticamente e defumado

O presente trabalho teve como objetivo a obtenção de isotermas de dessorção de filés de bonito (Sarda sarda), previamente salgados a vácuo e defumados com fumaça líquida. As isotermas foram obtidas a quatro temperaturas (5, 25, 40 e 60 ºC) em condições de dessorção, através do método gravimétrico estático, com soluções salinas saturadas. Os dados experimentais foram ajustados a quatro modelos da literatura (BET linearizado, GAB, Henderson e Oswin modificado). Os resultados mostraram que as isotermas tomaram forma sigmoidal de tipo II e que o modelo de Guggenheim-Anderson-deBoer (GAB) foi aceitável para modelar os dados experimentais. O calor isostérico de dessorção, um parâmetro necessário para simular e projetar adequadamente o secador, também foi calculado e pode ser representado através de um modelo matemático simples, em função da umidade de equilíbrio.

Low-energy electron scattering from methanol and ethanol

Measured and calculated differential cross sections for elastic (rotationally unresolved) electron scattering from two primary alcohols, methanol (CH(3)OH) and ethanol (C(2)H(5)OH), are reported. The measurements are obtained using the relative flow method with helium as the standard gas and a thin aperture as the collimating target gas source. The relative flow method is applied without the restriction imposed by the relative flow pressure conditions on helium and the unknown gas. The experimental data were taken at incident electron energies of 1, 2, 5, 10, 15, 20, 30, 50, and 100 eV and for scattering angles of 5 degrees-130 degrees. There are no previous reports of experimental electron scattering differential cross sections for CH(3)OH and C(2)H(5)OH in the literature. The calculated differential cross sections are obtained using two different implementations of the Schwinger multichannel method, one that takes all electrons into account and is adapted for parallel computers, and another that uses pseudopotentials and considers only the valence electrons. Comparison between theory and experiment shows that theory is able to describe low-energy electron scattering from these polyatomic targets quite well.

Combining Mager and Steinmetz: The Effect of Grain Size and Maximum Induction on Hysteresis Energy Loss

Twelve samples with different grain sizes were prepared by normal grain growth and by primary recrystallization, and the hysteresis dissipated energy was measured by a quasi-static method. Results showed a linear relation between hysteresis energy loss and the inverse of grain size, which is here called Mager`s law, for maximum inductions from 0.6 to 1.5 T, and a Steinmetz power law relation between hysteresis loss and maximum induction for all samples. The combined effect is better described by a Mager`s law where the coefficients follow Steinmetz law.

High-pressure phase diagram of the drug mitotane in compressed and/or supercritical CO(2)

This work provides experimental phase diagram of mitotane, a drug used in the chemotherapy treatment of adrenocortical carcinoma, in compressed and/or supercritical CO(2). The synthetic-static method in a high-pressure variable-volume view cell coupled with a transmitted-light intensity probe was used to measure the solid-fluid (SF) equilibrium data. The phase equilibrium experiments were determined in temperature ranging from (298.2 to 333.1) K and pressure up to 22 MPa. Peng-Robinson equation of state (PR-EoS) with classical mixing rule was used to correlate the experimental data. Excellent agreement was found between experimental and calculated values. (C) 2009 Elsevier Ltd. All rights reserved.

Prospective analysis of KRAS, BRAF, and PIK3CA mutations and EGFR copy number in patients (pts) with locally advanced rectal cancer: A translational substudy of a clinical trial (SAKK 41/07) evaluating the effect of neoadjuvant chemoradiation (CRT) with or without panitumumab

Background: Prognostic and predictive markers are of great importance for future study designs and essential for the interpretation of clinical trials incorporating an EGFR-inhibitor. The current study prospectively assessed and validated KRAS, BRAF and PIK3CA mutations in rectal cancer patients screened for the trial SAKK41/07 of concomitant preoperative radio-chemotherapy with or without panitumumab.Methods: Macrodissection was performed on pretreatment formalin fixed paraffin embedded biopsy tissue sections to arrive at a minimum of 50% of tumor cells. DNA was extracted with the Maxwell 16 FFPE Tissue LEV DNA purification kit. After PCR amplification, mutations were identified by pyrosequencing. We prospectively analysed pretreatment biopsy material from 149 rectal cancer pts biopsies for KRAS (exon 2 codon 12 [2-12] and 13 [2-13], exon 3 codon 59 [3-59]) and 61 [3-61], exon 4 codon 117 [4-117] and 146 [4-146]). Sixty-eight pts (KRASwt exon 2, 3 only) were further analysed for BRAF (exon 15 codon 600) and PIK3CA (exon 9 codon 542, 545 and 546, exon 20 codon 1043 [20-1043] and 1047 [20-1047]) mutations, and EGFR copy number by qPCR. For the calculation of the EGFR copy number, we used KRAS copy number as internal reference standard. The calculation was done on the basis of the two standard curves relative quantification method.Results: In 149 screened pts with rectal cancer, the prevalence of KRAS mutations was 36%. Among the 68 pts enrolled in SAKK 41/07 based on initially presumed KRASwt status (exon 2/codons 12+13), 18 pts (26%) had a total of 23 mutations in the RAS/PIK3CA-pathways upon validation analysis. Twelve pts had a KRAS mutation, 7 pts had a PIK3CA mutation, 3 pts had a NRAS mutation, 1 patient a BRAF mutation. Surprisingly, five of these pts had double- mutations, including 4 pts with KRAS plus PIK3CA mutations, and 1 pt with NRAS plus PIK3CA mutations. The median normalized EGFR copy number was 1. Neither mutations of KRAS, BRAF, and PIK3CA, nor EGFR copy number were statistically associated with the primary study endpoint pCR (pathological complete regression).Conclusions: The prevalence of KRAS mutations in rectal and in colon cancer appears to be similar. BRAF mutations are rare; PIK3CA mutations are more common (10%). EGFR copy number is not increased in rectal cancer. A considerable number or KRAS exon 2 wt tumors harbored KRAS exon 3+4 mutations. Further study is needed to determine if KRAS testing should include exons 2-4.

HIGH PRESSURE VAPOR-LIQUID EQUILIBRIA OF PALM FATTY ACIDS DISTILLATES-CARBON DIOXIDE SYSTEM

Vapor-Liquid equilibria of palm fatty acids distillates/carbon dioxide system has been investigated experimentally at temperatures of 333, 353, and 373 K and pressures of 20, 23, 26, and 29 MPa using the static method. Experimental data for the quasi-binary system palm fatty acids distillates/carbon dioxide has been correlated with Redlich-Kwong-Aspen equation of state. Modeling shows good agreement with experimental data. Selectivity obtained indicates that supercritical carbon dioxide is a reasonable solvent for separating saturated (palmitic acid) and unsaturated (oleic+linoleic acids) fatty acids from palm fatty acids distillates in a continuous multistage countercurrent column.

Drying of sicilian lemon residue: influence of process variables on the evaluation of the dietary fiber produced

In this study, the effect of the process variables of the air-drying of Sicilian lemon residues on some technological properties of the fibers produced was studied. The determination and modeling of desorption isotherms were used to establish the equilibrium moisture content at 60, 75, and 90 °C using the static method with 8 saturated salt solutions. The best fit was obtained with BET and GAB models. The drying process was conducted in a vertical tray dryer and delineated according to a central composite experimental design (2²) using the following as factors: air velocity (0.5, 0.75 and 1 m/s) and temperature (60, 75, and 90 °C), and it presented a good fit to the exponential model (R² > 99.9%). The experimental design responses evaluated were the technological properties of the fibers: water-holding, oil-holding, and swelling capacity. Since these properties were present in high levels, the lemon residues could be used to increase content of fibers in foods resulting in the addition of nutritional benefits for the consumers.

Estado situacional de los modelos basados en agentes y su impacto en la investigación organizacional

En un mundo hiperconectado, dinámico y cargado de incertidumbre como el actual, los métodos y modelos analíticos convencionales están mostrando sus limitaciones. Las organizaciones requieren, por tanto, herramientas útiles que empleen tecnología de información y modelos de simulación computacional como mecanismos para la toma de decisiones y la resolución de problemas. Una de las más recientes, potentes y prometedoras es el modelamiento y la simulación basados en agentes (MSBA). Muchas organizaciones, incluidas empresas consultoras, emplean esta técnica para comprender fenómenos, hacer evaluación de estrategias y resolver problemas de diversa índole. Pese a ello, no existe (hasta donde conocemos) un estado situacional acerca del MSBA y su aplicación a la investigación organizacional. Cabe anotar, además, que por su novedad no es un tema suficientemente difundido y trabajado en Latinoamérica. En consecuencia, este proyecto pretende elaborar un estado situacional sobre el MSBA y su impacto sobre la investigación organizacional.

The kinetics of the gas-phase reactions of selected monoterpenes and cyclo-alkenes with ozone and the NO3 radical

The relative rate method has been used to measure the room-temperature rate constants for the gasphase reactions of ozone and NO3 with selected monoterpenes and cyclo-alkenes with structural similarities to monoterpenes. Measurements were carried out at 298 ! 2 K and 760 ! 10 Torr. The following rate constants (in units of 10"18 cm3 molecule"1 s"1) were obtained for the reaction with ozone: methyl cyclohexene (132 ! 17), terpinolene (1290 ! 360), ethylidene cyclohexane (223 ! 57), norbornene (860 ! 240), t-butyl isopropylidene cyclohexane (1500 ! 460), cyclopentene (543 ! 94), cyclohexene (81 ! 18), cyclooctene (451 ! 66), dicyclopentadiene (1460 ! 170) and a-pinene (107 ! 13). For the reaction with NO3 the rate constants obtained (in units of 10"12 cm3 molecule"1 s"1) were: methyl cyclohexene (7.92 ! 0.95), terpinolene (47.9 ! 4.0), ethylidene cyclohexane (4.30 ! 0.24), norbornene (0.266 ! 0.029), cyclohexene (0.540 ! 0.017), cyclooctene (0.513 ! 0.029), dicyclopentadiene (1.20 ! 0.10) and a-pinene (5.17 ! 0.62). Errors are quoted as the root mean square of the statistical error (95% con!dence) and the quoted error in the rate constant for the reference compound. Combining these results with previous studies, new recommendations for the rate constants are presented. Molecular orbital energies were calculated for each alkene and the kinetic data are discussed in terms of the deviation from the structureeactivity relationship obtained from the rate constants for a series of simple alkenes. Lifetimes with respect to key initiators of atmospheric oxidation have been calculated suggesting that the studied reactions play dominant roles in the night-time removal of these compounds from the atmosphere.

Atmospheric electric field measurements in urban environment and the pollutant aerosol weekly dependence

The weekly dependence of pollutant aerosols in the urban environment of Lisbon (Portugal) is inferred from the records of atmospheric electric field at Portela meteorological station (38°47′N,9°08′W). Measurements were made with a Bendorf electrograph. The data set exists from 1955 to 1990, but due to the contaminating effect of the radioactive fallout during 1960 and 1970s, only the period between 1980 and 1990 is considered here. Using a relative difference method a weekly dependence of the atmospheric electric field is found in these records, which shows an increasing trend between 1980 and 1990. This is consistent with a growth of population in the Lisbon metropolitan area and consequently urban activity, mainly traffic. Complementarily, using a Lomb–Scargle periodogram technique the presence of a daily and weekly cycle is also found. Moreover, to follow the evolution of theses cycles, in the period considered, a simple representation in a colour surface plot representation of the annual periodograms is presented. Further, a noise analysis of the periodograms is made, which validates the results found. Two datasets were considered: all days in the period, and fair-weather days only.

Aplicação de microemulsões na solubilização de frações pesadas de petróleo

This work presents studies related to the use of microemulsions in the solubilization of heavy crude oil fractions responsible by the formation of deposits. The first stage of the work was addressed to the construction of phases diagrams, with the intention of determining the area within which the microemulsion is formed. The following systems were studied: UNITOL L 90 n-Butanol - Water - Kerosene (system 1); UNITOL L 90 - n-Butanol - Water - Xylene (system 2); UNITOL L 90 n-Butanol - Water - Kerosene/Xylene 10% (system 3); UNITOL L 90 - Sec-Butanol - Water - Xylene (system 4). In parallel experiments of physical adsorption were carried out by the static method, with the intention of simulating natural conditions of reservoirs. Crude oil of the Fazenda Belém field (Rio Grande do Norte), was used as solute, xylene as solvent and the Assu sandstone (Rio Grande do Norte, Brazil) and Botucatu sandstone (Paraná, Brazil) as rock reservoirs. The curves of adsorption presented the S format type, in agreement with the classification proposed by Giles, Smith and Huitson (1974). The solubilization process was accomplished in the batch method, by varying the time of agitation, the microemulsions and the solid/solution ratio. The experiments showed that the microemulsions presented high efficiency in the solubilization of the crude oil adsorbed on the sandstones. System 2 presented an efficiency of 99% for the Assu sandstone and 97% for the Botucatu sandstone