Local buckling behaviour of steel plate elements supported by a plastic foam material

Sandwich panels comprising steel facings and a polystyrene foam core are increasingly used as roof and wall claddings in buildings in Australia. When they are subjected to loads causing bending and/or axial compression, the steel plate elements of their profiled facing are susceptible to local buckling. However, when compared to panels with no foam core, they demonstrate significantly improved local buckling behaviour because they are supported by foam. In order to quantify such improvements and to validate the use of available design buckling stress formulae, an investigation using finite element analyses and laboratory experiments was carried out on steel plates that are commonly used in Australia of varying yield stress and thickness supported by a polystyrene foam core. This paper presents the details of this investigation, the buckling results and their comparison with available design buckling formulae.

Branched polystyrene with abundant pendant vinyl functional groups from asymmetric divinyl monomer

Branched polystyrenes with abundant pendant vinyl functional groups were prepared via radical polymerization of an asymmetric divinyl monomer, which possesses a higher reactive styryl and a lower reactive butenyl. Employing a fast reversible addition fragmentation chain transfer (RAFT) equilibrium, the concentration of active propagation chains remained at a low value and thus crosslinking did not occur until a high level of monomer conversion. The combination of a higher reaction temperature (120 degrees C) and RAFT agent cumyl dithiobenzoate was demonstrated to be optimal for providing both a more highly branched architecture and a higher polymer yield.

Syndiospecific polymerization of styrene with multi-nuclear titanium complexes

Two multi-nuclear titanium complexes [Ti(eta(5)-Cp-*) Cl(mu-O)](3) ( 1) and [(eta(5)-(CpTiCl)-Ti-*)(mu-O)(2)(eta(5)-(CpTi)-Ti-*)(2)(mu-O)(mu-O)(2)](2)Ti (Cp-* = C5Me5) ( 2) have been investigated as the precatalysts for syndiospecific polymerization of styrene. In the presence of modified methylaluminoxane ( MMAO) as a cocatalyst, complexes 1 and 2 display much higher catalytic activities towards styrene polymerization, and produce the higher molecular weight polystyrenes with higher syndiotacticities and melting temperatures ( T-m) than the mother complex (CpTiCl3)-Ti-* does when the polymerization temperature is above 70 degrees C and the Al/Ti molar ratio is in the low range especially.

Preparation and characterization of post-derivatives from functional polystyrene (ATRP) with p-nitroaniline-azomethine phenol and their thermal and optical study

The functional polystyrene, (Cl-PS)(2)-CHCOOCH2CH2OH ( designated as XPSt and coded P2) was prepared by ATRP at 130(0)C using CuCl and bipyridine as catalysts, 2,2-dichloro acetate-ethylene glycol (DCAG) as multifunctional initiator and THF as solvent. 4-Nitoroaniline azomethine-4' phenol (P1) as chromophores were covalently linked to the functional end groups of the polymer by using simple displacement reaction. The functional polystyrenes, namely XPSt (P2) and (PS)(2)-CHCOOCH2CH2OH, designated as X-PSt and coded P3 and their post-derivatives, namely, DXPSt (P4) and DX-PSt (P5) respectively were characterized by IR, NMR and UV spectroscopies, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), polarising optical microscopy (POM) and XRD studies. DSC showed that incorporation of chromophores in the side chains of polymers towards the polystyrene moiety increases the rigidity of the polymer and subsequently, its glass transition temperature; however the incorporation of side chain towards the alcoholic functional group decreases the glass transition temperature. The post derivatives do not play any significant role to increase the thermal stability ( TGA).

AFM study of the self-assembly behavior of hexa-armed star polymers with a discotic triphenylene core

The size-armed polystyrenes and poly-(methyl methacrylate)s with a triphenylene core showed different self-assembling patterns, isolated cylinders for polySt on mico and highly ordered cylindrical pores for polyMMA on a silicon water. With a decrease of polymer concentration in tetrahydrofuran (HHF), the size and height of cylinders decreased for polySt, but fur polyMMA, the size and depth of the cylindrical pores increased. Slow evaporation of the solvent and a low molecular weight favored the formation of regular patterns.

COMPARISON OF THE BEHAVIOR OF CYCLIC AND LINEAR POLYSTYRENE IN DILUTE-SOLUTION

Using a low angle laser light scattering photometer, the second virial coefficients (A2) of both cyclic and linear polystyrene were determined in cyclohexane, toluene and methyl ethyl ketone (MEK) solutions. From the data obtained in cyclohexane solution the theta-temperature of cyclic polystyrene was determined to be 30-degrees-C. In toluene solution A2 of cyclic polystyrene is smaller than that of linear polystyrene with the same molecular weight, but in MEK the values are similar.

Diblock and Triblock Copolymers of Styrene and Acetoxymethylstyrene by One-Pot ATRP

We describe the synthesis of diblock and triblock copolymers by sequential atom transfer radical polymerization of styrene and acetoxymethylstyrene. Contrary to the usual block copolymerization involving isolation of the macroinitiator, a convenient one-pot procedure is developed. This is possible because of the preferential polymerization of acetoxymethylstyrene, even in the presence of residual styrene, as inferred from characterization of the intermediate polystyrenes and the block copolymers by size exclusion chromatography, 1H NMR, Fourier transform infrared spectroscopy, differential scanning calorimetry, and GPEC techniques. The latent acetoxy functionalities in these block copolymers are shown to be easily unmasked to OOH and OBr functionalities, with the potential for block ionomers and dense graft architectures.

Studies on the behaviour of polystyrene in reversed phase chromatography

Polystyrene behaviour in reversed phase high performance liquid chromatography was influenced mainly by the solvent system, but secondary affects were observed depending on the stationary phase. A variety of reversed phase columns were investigated using mobile phase combinations of dichlorom ethane-methanol, dichloromethane-acetonitrile, ethyl acetate-methanol and ethyl acetate-acetonitrile. Several different modes of behaviour were observed depending on the polymer solubility in the solvent system. In the dichloromethane-methanol solvent system, polymer-stationary phase interactions only occurred when the molecules had pore access. Retention of excluded polystyrene depended on the kinetics of precipitation and redissolution of the polymer. Peak splitting and band broadening occurred when the kinetics were slow and molecular weight separations were limited !o oligomers and polystyrenes lower than 5-10(4) dalton. Excellent molecular weight separations of polystyrenes were obtained using gradient elution reversed phase chromatography with a dichloromethane-acetonitrile mobile phase on C18 columns. The retention was based on polymer-stationary phase interactions regardless of the column pore size. Separations were obtained on large diameter pellicular adsorbents that were almost as good as those obtained on porous adsorbents, showing that pore access was not essential for the retention of high molecular weight polystyrenes. In the best example, the separation ranged from the monomer to 10(6) dalton in a single analysis. Very little adsorption of excluded polymers was observed on C8 or phenyl columns. Polystyrene molecular weight separations to 7-10(5) dalton were obtained in an ethyl acetate-acetonitrile solvent system on C18 columns. Adsorption was responsible for retention. When an ethyl acetate-methanol solvent system was used, no molecular weight separations were obtained because of complex peak splitting. Reversed phase chromatography was compared to size exclusion chromatography for the analysis of polydisperse polystyrenes. Similar results were obtained using both methods. However, the reversed phase method was less sensitive to concentration effects and gave better resolution.

Forces measured between latex spheres in aqueous electrolyte : Non-DLVO behavior and sensitivity to dissolved gas

An atomic force microscope was used to measure the forces acting between two polystyrene latex spheres in aqueous media. The results show an electrostatic repulsion at large separations which is overtaken by an attractive “hook” that pulls the two spheres into contact from a considerable range (20−400 nm), much larger than could be expected for a van der Waals attraction. The range of operation of this attraction varies from one experiment to another and is not correlated with electrolyte concentration. However, the range is found to decrease significantly when the level of dissolved gas in the water is reduced.

Electrospinning of nanofibres with parallel line surface texture for improvement of nerve cell growth

Nanofibres having a parallel line surface texture were electrospun from cellulose acetate butyrate solutions using a solvent mixture of acetone and N,N'-dimethylacetamide. The formation mechanism of the unusual surface feature was explored and attributed to the formation of voids on the jet surface at the early stage of electrospinning and subsequent elongation and solidification of the voids into a line surface structure. The fast evaporation of a highly volatile solvent, acetone, from the polymer solution was found to play a key role in the formation of surface voids, while the high viscosity of the residual solution after the solvent evaporation ensured the line surface to be maintained after the solidification. Based on this principle, nanofibres having a similar surface texture were also electrospun successfully from other polymers, such as cellulose acetate, polyvinylidene fluoride, poly(methyl methacrylate), polystyrene and poly(vinylidene fluoride-co-hexafluoropropene), either from the same or from different solvent systems. Polarized Fourier transform infrared spectroscopy was used to measure the polymer molecular orientation within nanofibres. Schwann cells were grown on both aligned and randomly oriented nanofibre mats. The parallel line surface texture assisted in the growth of Schwann cells especially at the early stage of cell culture regardless of the fibre orientation. In contrast, the molecular orientation within nanofibres showed little impact on the cell growth.

Influence of ionic liquids on the electrical conductivity and morphology of PEDOT:PSS films

Small-molecule nonvolatile additives based on ionic liquids (IL) as electrical conductivity enhancer in Poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) was studied. Ionic liquids were investigated in the synthesis of self-assembled, highly organized hybrid nanostructures due to their ability as supramolecular solvents. Different percentage of five ionic liquids, such as 1-butyl-3-methylimidazolium tetrafluoroborate (bmim) F 4 and 1-butyl-3-methylimidazolium bromide (bmim)Br were added to a PEDOT:PSScommercial dispersion. Films of pure PEDOT:PSS showed an average conductivity of 14 S cm-1, which corresponded to the value range given by the supplier. AFM images showed that IL induced the formation of a three-dimensional conducting network with smaller PEDOT domains. The ionic character of the films was significantly increased because of the presence of ionic liquids, which can be used effectively in optoelectronic devices.

Phase behavior and nanomechanical mapping of block ionomer complexes

Block ionomer complexes SSEBS-c-PCL were prepared, as a consequence of proton transfer from the sulfonic acid of sulfonated polystyrene-block- poly(ethylene-ran-butylene)-block-polystyrene (SSEBS) to the tertiary amine of a tertiary amine terminated poly(?-caprolactone) (APCL). The phase behavior of SSEBS-c-PCL was thoroughly investigated and the results showed that APCL in SSEBS-c-PCL displays unique crystallization behavior owing to the influence of interactions between the amine and sulfonic acid groups as well as the effects of confinement. Further, small-angle X-ray scattering study revealed that SSEBS-c-PCL displays a less ordered micro-phase structure compared to SSEBS. A quantitative mapping of mechanical properties at the nanoscale was achieved using peak force mode atomic force microscopy. It is found that the block ionomer complex possesses a higher average elastic modulus after complexation with crystallizable APCL. Additionally, the moduli for both hard and soft phases increase and the phase with higher modulus assignable to the hard SPS component shows much more pronounced changes after complexation, confirming that APCL interacts mainly with the SPS blocks. This provides an understanding of the composition and nanomechanical properties of these new block ionomer complexes and an alternative insight into the micro-phase structures of multi-phase materials.

Phase inversion of ionomer-stabilized emulsions to form high internal phase emulsions (HIPEs)

Herein, we report the phase inversion of ionomer-stabilized emulsions to form high internal phase emulsions (HIPEs) induced by salt concentration and pH changes. The ionomers are sulfonated polystyrenes (SPSs) with different sulfonation degrees. The emulsion types were determined by conductivity measurements, confocal microscopy and optical microscopy, and the formation of HIPE organogels was verified by the tube-inversion method and rheological measurements. SPSs with high sulfonation degrees (water-soluble) and low sulfonation degrees (water-insoluble) can stabilize oil-in-water emulsions; these emulsions were transformed into water-in-oil HIPEs by varying salt concentrations and/or changing the pH. SPS, with a sulfonation degree of 11.6%, is the most efficient, and as low as 0.2 (w/v)% of the organic phase is enough to stabilize the HIPEs. Phase inversion of the oil-in-water emulsions occurred to form water-in-oil HIPEs by increasing the salt concentration in the aqueous phase. Two phase inversion points from oil-in-water emulsions to water-in-oil HIPEs were observed at pH 1 and 13. Moreover, synergetic effects between the salt concentration and pH changes occurred upon the inversion of the emulsion type. The organic phase can be a variety of organic solvents, including toluene, xylene, chloroform, dichloroethane, dichloromethane and anisole, as well as monomers such as styrene, butyl acrylate, methyl methacrylate and ethylene glycol dimethacrylate. Poly(HIPEs) were successfully prepared by the polymerization of monomers as the continuous phase in the ionomer-stabilized HIPEs.

Development of starch biobased and biodegradable plastics for their use in trays for food-packaging

This research work develops new methods to produce biodegradable starch-based trays for the purpose of replacing expanded polystyrene in the food packaging market. The starch based biopolymers present several drawbacks like poor mechanical properties and very high density. In order to overcome these drawbacks two research lines have been set up: blending thermoplastic starch with biobased reinforcements from agricultural wastes like barley straw and grape wastes, and testing the foamability of these materials with a Microwave-foaming method.

Changes during chilled storage of whole tilapia and short-term frozen storage of tilapia fillets

This study evaluated the physicochemical changes in Nile tilapia (n = 82, 373.71 ± 61.91 g) refrigerated for up to 92 h and in the frozen fillets. The tilapias were captured with nets, slaughtered by ice and water shock (1:1) in a temperature of approximately 2°C for 30 min, and stored refrigerated at 4°C in polystyrene boxes containing ice. The fish were filleted, and filets were weighed and frozen. The drip loss and protein were determined after 23 days of frozen storage. After 4 h of storage, all fish were in full rigor mortis. The pH of the muscles decreased for up to 45 h of the storage period. The fillets obtained from tilapia stored for more than 72 h lost more weight and protein. Thus, the filleting or processing of tilapia should be done before 72 h of cold storage, since deterioration of the fish starts to occur after this period. Copyright © Taylor & Francis Group, LLC.