Development and Evaluation of a Novel pH Indicator Biodegradable Film Based on Cassava Starch

A pH indicator film based on cassava starch plasticized with sucrose and inverted sugar and incorporated with grape and spinach extracts as pH indicator sources (anthocyanin and chlorophyll) has been developed, and its packaging properties have been assessed. A second-order central composite design (2(2)) with three central points and four star points was used to evaluate the mechanical properties (tensile strength, tensile strength at break, and elongation at break percentage), moisture barrier, and microstructure of the films, and its potential as a pH indicator packaging. The films were prepared by the casting technique and conditioned under controlled conditions (75% relative humidity and 23 degrees C), at least 4 days before the analyses. The materials were exposed to different pH solutions (0, 2, 7, 10, and 14) and their color parameters (L*, a*, b*, and haze) were measured by transmittance. Grape and spinach extracts have affected the material characterization. Film properties (mechanical properties and moisture barrier) were strongly influenced by extract concentration presenting lower results than for the control. Films containing a higher concentration of grape extract presented a greater color change at different pH`s suggesting that anthocyanins are more effective as pH indicators than chlorophyll or the mixture of both extracts. (C) 2010 Wiley Periodicals, Inc. J Appl Polym Sci 120: 1069-1079,2011

Endophytic fungi producing of esterases: evaluation in vitro of the enzymatic activity using pH indicator

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

pH testing for detecting the position of nasogastric tubes in adults and children (Intervention Protocol)

This is the protocol for a review and there is no abstract. The objectives are as follows: Our objective is to determine if there is sufficient evidence to recommend the use of pH testing (the intervention under scrutiny) for verification of correct placement of nasogastric tubes in adults and children. To this end, we will attempt to answer the following questions: 1. In adults and children, is pH testing an effective and safe method for determining whether nasogastric tubes are correctly positioned in the stomach before feeding (or delivery of any fluid) begins? 2. What evidence is there about the risk of adverse events in the case of incorrect placement? For this review, pH testing is defined as: litmus paper, pH indicator test strips, pH meters. These will be tested against other methods used for detecting placement of nasogastric tubes, including visual examination of aspirate, auscultation with insufflation of air, detection of air bubbles in a bowl of water, X-ray, ultrasonography, endoscopy, enzyme analysis of aspirate, capnography, and other methods that do not rely on measurement of pH.

Determination of organophosphate and carbamate pesticides based on enzyme inhibition using a pH-sensitive fluorescence probe

A flow injection system for the determination of organophosphate and carbamate pesticides is described. A sensitive fluorescence probe was synthesized and used as the pH indicator to detect the inhibition of the enzyme acetylcholinesterase (ACNE). The percentage inhibition of enzyme activity is correlated to the pesticide concentration. Several parameters influencing the performance of the system are discussed. The detection limits of 3.5, 50, 12 and 25 mug/l for carbofuran, carbaryl, paraoxon and dichlorvos, in pure water, respectively were achieved with an incubation time of 10 min. A complete cycle of analysis, including incubation time, took 14 min. The detection system has been applied to the determination of carbofuran in spiked vegetable juices (Chinese cabbage and cole), achieving recovery values between 93.2 and 107% for Chinese cabbage juice and 108 and 118% for cole juice at the different concentration levels assayed. (C) 2004 Elsevier B.V. All rights reserved.

A comparison between diatom inferred ph changes and diatom populations in brownwater and clearwater lakes

The objective of this study was to determine whether clearwater and brownwater lakes differed in their rate of acidification as inferred by subfossil diatoms analyzed in recent downcore sediments. Differences between associations of diatom populations in brownwater and clearwater environments were characterized. Sediment cores were taken from four lakes located north and east of Lake Superior, near Wawa, Ontario. Two of these lakes were humicrich, brownwater lakes ( lakes U1 and CB2). The two other lakes were clearwater lakes ( lakes Xl and CF). The regression of Nygaard log index-alpha for surficial diatom sediments on observed pH ( Inferred pH = 6.57 - 0.82 log index-alpha ), was utilized to infer lake pH in recent sediments of these lakes. Upon analyzing the downcore diatoms, it was discovered that no significant change, in downcore diatom inferred pH, could be detected in the two brownwater lakes. In contrast, the two clearwater lakes showed significant shifts in downcore diatom inferred pH. In one of these lakes, pH had dropped from 5.3 to 4.5, in the top 9.0 cm of the core, while in the second lake, pH had dropped from 5.4 to 5.0 in the top 1.5 cm of the core. These findings suggested that humic substances, found in brownwater lakes, imparted a buffering capacity to these lake waters. In the clearwater lakes, the decrease in pH was very probably a consequence of acid precipitation. The Ambrosia rise ( circa 1890 ) occurred at the same depth in both brownwater lakes ( 11.0 - 12.0 cm). In both clearwater lakes, the Ambrosia rise occurred at a depth of 14.0 - 15.0 cm. This suggested a lower sedimentation rate in the brownwater lakes. pH influenced the total percentage composition of diatom pH indicator groups. Greater numbers of alkaliphilous taxa were found in less acidic lakes ( e.g. Lake Ul ), While greater numbers of acidloving forms were found in highly acidic lakes ( e.g. Lake Xl ). There was a greater abundance of indifferent forms in the brownwater lakes, than in the clearwater lakes. A number of diatom genera and species were found to be associated with either clearwater or brownwater conditions. The centric diatom, ~elosira distans, significantly increased in abundance in the recent sediments of both clearwater lakes. This may be indicating a shift toward a more oligotrophic state within these acidic, clearwater lakes. This study suggested that a pH index based on subfossil diatoms may be a sensitive indicator of changing lake pH. This study also indicated that humic substances may playa more important role, than previously acknowledged, in controlling the pH dynamics of lake waters, and in determining diatom populations.

The utility of sedimentary diatoms as a measure of historical lake ph

As a result of increased acid precipitation, the pH of a large number of Canadian Shield lakes has been falling. Prior to this study there was no documentation available to explain the history of lake acidification for the Algoma area lakes. In order to obtain this information the diatom inferred pH technique was developed in this study. During two field seasons, July 1981 and July 1982, short sediment cores (circa 25-30 cm) were collected from 28 study lakes located north of Lake Superior, District Algoma, Ontario. The surface sediment diatoms (0-1 cm) from each of these lakes were carefully identified, enumerated, and classified in terms of their pH indicator status. The surface sediment diatom analysis indicated that lake pH is one of the most important factors affecting the species composition and relative abundance of diatom populations. Thus diatom assemblages can be sensitive indicators of lake acidification. When Nygaard's index alpha was plotted against observed lake pH, a statistically significant relationship resulted (r=-0.89; p=pha regression equation was used to construct the pH histories of 4 lakes (lakes X4, CS, U3, and WI). The repeatability of this technique was confirmed by comparing two downcore paleo-pH profiles of Lake WI. These two paleo-pH profiles represented almost identical paleo-pH patterns for Lake WI. The paleo-pH study of Lake X4 revealed that the lake has been rather acidic (pH <5.6) for the last 200 years. It appears that the recent increase in acid precipitation 3 over the last 30 years has not altered the water pH compared to the lake's pH history. However, the paleo-pH study of another acidic lake (Lake CS) indicated that its pH has significantl}* dropped over the last 30 years . During this time the Lake CS pH has dropped almost 2 pH units (7.1 to 5.2). The other two lakes studied for downcore pH were circumneutral in nature . One of these lakes (Lake U3) displayed a relatively stable pH history while the other lake (Lake WI) displayed significant pH fluctuations over post-Ambrosia time. The variable pH history of Lake WI was probably associated with the Algoma sintering plant plume and forest fires. A significant relationship between surface sediment diatoms and observed lake pH and secondly a statistically significant relationship between index alpha and observed pH suggested that diatoms are one of the best indicators of lake pH. Thus diatom inferred pH technique has great potential in explaining the rate of lake acidification.

Simulação de transporte eletrônico em dispositivos unimoleculares baseados em indicadores de pH

Nas últimas décadas, diversos pesquisadores têm tentado empregar moléculas em dispositivos eletrônicos de nanoescala. Por este motivo, diferentes parâmetros eletro/ópticos, que regem o transporte eletrônico em moléculas orgânicas, precisam ser analisados. Neste trabalho foi desenvolvido um estudo de transporte de carga para o composto Vermelho de Propila, popularmente utilizado como indicador de pH. A motivação para estudá-lo resulta de sua estrutura constituída por subunidades doadora-aceitadora, acopladas via grupo azo (N=N), uma característica bem conhecida em retificadores moleculares. A metodologia utilizada para tratar o sistema em equilíbrio é baseada em métodos de Mecânica Molecular e Hartree-Fock. Sendo que, para simular o sistema em não-equilíbrio, foi empregado o formalismo de Landauer-Büttiker. Através desses métodos, as curvas características do sistema molecular foram traçadas e comparadas. O resultado da comparação permitiu explicar os fenômenos que regem o transporte eletrônico na nanoestrutura. Além disso, foram analisados os efeitos de contatos metálicos, ligados a molécula na presença de campo elétrico externo.

Development and characterization of fluorescent pH sensors based on porous silica and hydrogel support matrices

The hydrogen ion activity (pH) is a very important parameter in environment monitoring, biomedical research and other applications. Optical pH sensors have several advantages over traditional potentiometric pH measurement, such as high sensitivity, no need of constant calibration, easy for miniaturization and possibility for remote sensing. Several pH indicators has been successfully immobilized in three different solid porous materials to use as pH sensing probes. The fluorescent pH indicator fluorescein-5-isothiocyanate (FITC) was covalently bound onto the internal surface of porous silica (pore size ~10 nm) and retained its pH sensitivity. The excited state pK* a of FITC in porous silica (5.58) was slightly smaller than in solution (5.68) due to the free silanol groups (Si-OH) on the silica surface. The pH sensitive range for this probe is pH 4.5 - 7.0 with an error less than 0.1 pH units. The probe response was reproducible and stable for at least four month, stored in DI water, but exhibit a long equilibrium of up to 100 minutes. Sol-gel based pH sensors were developed with immobilization of two fluorescent pH indicators fluorescein-5-(and-6)-sulfonic acid, trisodium salt (FS) and 8-hydroxypyrene- 1,3,6-trisulfonic acid (HPTS) through physical entrapment. Prior to immobilization, the indicators were ion-paired with a common surfactant hexadecyltrimethylammonium bromide (CTAB) in order to prevent leaching. The sol-gel films were synthesized through the hydrolysis of two different precursors, ethyltriethoxysilane (ETEOS) and 3- glycidoxypropyltrimethoxysilane (GPTMS) and deposited on a quartz slide through spin coating. The pK a of the indicators immobilized in sol-gel films was much smaller than in solutions due to silanol groups on the inner surface of the sol-gel films and ammonium groups from the surrounding surfactants. Unlike in solution, the apparent pK a of the indicators in sol-gel films increased with increasing ionic strength. The equilibrium time for these sensors was within 5 minutes (with film thickness of ~470 nm). Polyethylene glycol (PEG) hydrogel was of interest for optical pH sensor development because it is highly proton permeable, transparent and easy to synthesize. pH indicators can be immobilized in hydrogel through physical entrapment and copolymerization. FS and HPTS ion-pairs were physically entrapped in hydrogel matrix synthesized via free radical initiation. For covalent immobilization, three indicators, 6,8-dihydroxypyrene-1,3- disulfonic acid (DHPDS), 2,7-dihydroxynaphthalene-3,6-disulfonic acid (DHNDS) and cresol red were first reacted with methacrylic anhydride (MA) to form methacryloylanalogs for copolymerization. These hydrogels were synthesized in aqueous solution with a redox initiation system. The thickness of the hydrogel film is controlled as ~ 0.5 cm and the porosity can be adjusted with the percentage of polyethylene glycol in the precursor solutions. The pK a of the indicators immobilized in the hydrogel both physically and covalently were higher than in solution due to the medium effect. The sensors are stable and reproducible with a short equilibrium time (less than 4 minutes). In addition, the color change of cresol red immobilized hydrogel is vivid from yellow (acidic condition) to purple (basic condition). Due to covalently binding, cresol red was not leaching out from the hydrogel, making it a good candidate of reusable "pH paper".

Quantitative measurement of intraorganelle pH in the endosomal-lysosomal pathway in neurons by using ratiometric imaging with pyranine.

Organelle acidification is an essential element of the endosomal-lysosomal pathway, but our understanding of the mechanisms underlying progression through this pathway has been hindered by the absence of adequate methods for quantifying intraorganelle pH. To address this problem in neurons, we developed a direct quantitative method for accurately determining the pH of endocytic organelles in live cells. In this report, we demonstrate that the ratiometric fluorescent pH indicator 8-hydroxypyrene-1,3,6-trisulfonic acid (HPTS) is the most advantageous available probe for such pH measurements. To measure intraorganelle pH, cells were labeled by endocytic uptake of HPTS, the ratio of fluorescence emission intensities at excitation wavelengths of 450 nm and 405 nm (F450/405) was calculated for each organelle, and ratios were converted to pH values by using standard curves for F450/405 vs. pH. Proper calibration is critical for accurate measurement of pH values: standard curves generated in vitro yielded artifactually low organelle pH values. Calibration was unaffected by the use of culture medium buffered with various buffers or different cell types. By using this technique, we show that both acidic and neutral endocytically derived organelles exist in the axons of sympathetic neurons in different steady-state proportions than in the cell body. Furthermore, we demonstrate that these axonal organelles have a bimodal pH distribution, indicating a rapid acidification step in their maturation that reduces the average pH of a fraction of the organelles by 2 pH units while leaving few organelles of intermediate pH at steady state. Finally, we demonstrate a spatial gradient or organelle pH along axons, with the relative frequency of acidic organelles increasing with proximity to the cell body.

Development and assessment of new sensor systems in food packaging applications

The use of optical sensor technology for non-invasive determination of key quality pack parameters improved package/product quality. This technology can be used for optimization of packaging processes, improvement of product shelf-life and maintenance of quality. In recent years, there has been a major focus on O2 and CO2 sensor development as these are key gases used in modified atmosphere packaging (MAP) of food. The first and second experimental chapters (chapter 2 and 3) describe the development of O2, pH and CO2 solid state sensors and its (potential) use for food packaging applications. A dual-analyte sensor for dissolved O2 and pH with one bi-functional reporter dye (meso-substituted Pd- or Ptporphyrin) embedded in plasticized PVC membrane was developed in chapter 2. The developed CO2 sensor in chapter 3 was comprised of a phosphorescent reporter dye Pt(II)- tetrakis(pentafluorophenyl) porphyrin (PtTFPP) and a colourimetric pH indicator α-naphtholphthalein (NP) incorporated in a plastic matrix together with a phase transfer agent tetraoctyl- or cetyltrimethylammonium hydroxide (TOA-OH or CTA-OH). The third experimental chapter, chapter 4, described the development of liquid O2 sensors for rapid microbiological determination which are important for improvement and assurance of food safety systems. This automated screening assay produced characteristic profiles with a sharp increase in fluorescence above the baseline level at a certain threshold time (TT) which can be correlated with their initial microbial load and was applied to various raw fish and horticultural samples. Chapter 5, the fourth experimental chapter, reported upon the successful application of developed O2 and CO2 sensors for quality assessment of MAP mushrooms during storage for 7 days at 4°C.

Micro/nanoreservoirs for controlled release of active species in smart functional coatings

This work reports one possible way to develop new functional coatings used to increase the life time of metallic structures. The functionalities selected and attributed to model coatings in the frame of this work were corrosion protection, self-sensing and prevention of fouling (antifouling). The way used to confer those functionalities to coatings was based on the encapsulation of active compounds (corrosion inhibitors, pH indicators and biocides) in micro and nanocontainers followed by their incorporation into the coating matrices. To confer active corrosion protection, one corrosion inhibitor (2-mercaptobenzothiazole, MBT) was encapsulated in two different containers, firstly in silica nanocapsules (SiNC) and in polyurea microcapsules (PU-MC). The incorporation of both containers in different models coatings shows a significant improvement in the corrosion protection of aluminum alloy 2024 (AA2024). Following the same approach, SiNC and PU-MC were also used for the encapsulation of phenolphthalein (one well known pH indicator) to introduce sensing properties in polymeric coatings. SiNC and PU-MC containing phenolphthalein acted as corrosion sensor, showing a pink coloration due to the beginning of cathodic reaction, resulting in a pH increase identified by those capsules. Their sensing performance was proved in suspension and when integrated in coatings for aluminium alloy 2024 and magnesium alloy AZ31. In a similar way, the biocide activity (antifouling) was assigned to two polymeric matrices using SiNC for encapsulation of one biocide (Dichloro-2-octyl-2H-isothiazol-3-one, DCOIT) and also SiNC-MBT was tested as biocide. The antifouling activity of those two encapsulated compounds was assessed through inhibition and consequent decrease in the bioluminescence of modified E. coli. That effect was verified in suspension and when incorporated in coatings for AISI 1008 carbon steel. The developed micro and nanocontainers presented the desired performance, allowing the introduction of new functionalities to model coatings, showing potential to be used as functional additives in the next generation of multifunctional coatings.

Proton translocation by cytochrome c oxidase reconstituted into proteoliposomes

Cytochrome c oxidase .inserted into proteoliposomes translocates protons with a stoichiometry of approx-, imately 0.4-0.6 H+/e- in the presence of valinomycin plus pottasium. The existance .ofsuchproton translocation is .supportedby experiments with lauryl maltoside which abolished the pulses but~~d not inhibit cyt. c binding .or oxidase turnover. Pulses with K3FeCN6 did not induce acidification further supporting vectorial proton transport by cyt ..aa3 . Upon lowering the ionic strength and pulsing with ferrocytochrome c, H+/eratios increased. This increase is attributed to scaler proton release consequent upon cyt.c-phospholipid binding. Oxygen pulses at low ionic strength however did not exhibit this large scaler increase in H+/e- ratios.A-small increase was observed upon .02 pul'sing at·low ionic strengt.h. This increase was KeN and, ,pcep sensitive and thus possibly due to a redox linked scaler deprotonation. Increases in the H+/e- ratio also occurred ifp~lses ,were performed in the presence of nonactin rather.than valinomycin. The fluorescent pH indicator pyranine was internally trapped inaa3 conta~ning "proteoliposomes. Internal alkalinization, as mon,itored by pyranine fluorescence leads to a of approx.imately 0.35 units, which is proportional to electron flux. This internal alkalinization was also DCCD sensitive, being inhibited by approximately 50%. This 50% inhibition of internal alkalinization supports the existance of vectorial proton transport.

Marine bacterial prodigiosin as dye for rubber latex, polymethyl methacrylate sheets and paper

Prodigiosin is known for its immunomodulatory, antibacterial, antimycotic, antimalarial, algicidal and anticancer activities. Here, we reported the evaluation of prodigiosin pigment as a dyeing agent in rubber latex, paper and polymethyl methacrylate (PMMA) so that it can be considered as an alternative to synthetic pigments. Maximum color shade was obtained in rubber sheet prepared with 0.5 parts per hundred gram of rubber (phr) pigment and PMMA sheet incorporated with 0.08 μg pigment. Results indicate scope for utilization of prodigiosin as dye for PMMA and rubber and also prodigiosin dyed paper as a pH indicator. Further, being a natural and water insoluble pigment, it is ecofriendly

Modelamento do transporte eletrônico em dispositivos moleculares

No presente trabalho, simulamos as propriedades de transporte e espectro de absorção do composto orgânico Vermelho de Etila. Este é o primeiro estudo teórico de um indicador específico de pH utilizado como nanodispositivo, com base na teoria quântica e no modelo de transporte não-difuso. A distribuição de carga ao longo da molécula é determinada através da técnica, Ab initio, como uma função de um campo elétrico externo. Baseado em um modelo de multiníveis ressonantes também calculamos a corrente como função da tensão de polarização. O acúmulo de carga e a corrente apresentam comportamento semelhante, como a condução do tipo ressonante e curvas carga-tensão e corrente-tensão assimétricas. Os principais resultados sugerem que o sistema presente poderia funcionar como um transistor molecular bi-direcional. Estendemos esta metodologia de análise para outro dispositivo molecular, mas composto de três terminais. Para este sistema, nossa descoberta principal é a resistência diferencial negativa (RDN) na carga Q como uma função do campo elétrico externo. Para explicar este efeito RDN, aplicamos um modelo capacitivo fenomenológico, também baseado em um sistema de multiníveis localizados (que podem ser os LUMOs – Lowest Unoccupied Molecular Orbital – Orbitais moleculares desocupados mais baixos). A capacitância descreve, por efeito de carregamento, a causa do bloqueio de Coulomb (BC) no transporte. Mostramos que o efeito BC dá origem a uma RDN para um conjunto adequado de parâmetros fenomenológicos como: taxa de tunelamento e energia de carregamento. O perfil da RDN obtida nas duas metodologias, ab initio e fenomenológica, estão em comum acordo.

Investigação da dinâmica sequêncial Monte Carlo/Mecânica Quântica para sitemas moleculares orgânicos

O principal objetivo deste trabalho é investigar teóricamente as propriedades eletrônicas e óticas de compostos orgânicos em ambiente líquido. A compreensão das interações em sistemas líquidos é muito importante para a descrição de fenômenos em muitas partes da ciência, como Física, Química, Biologia e Materiais, bem como no desenvolvimento de materiais óticos. As flutuações térmicas fazem que inumaram das configurações para os líquidos possam ser gerados. Esta é a razão do comportamento estatístico observado em sistemas líquidos. Considerando estas dificuldades, o tratamento sequencial Monte Carlo / Mecânica Quântica (SMC/QM) é usado neste trabalho. Neste procedimento, a estrutura líquida é gerada primeiramente por simulações clássicas de MC e mais tarde, somente a parte mais importante do sistema é tratada com mecânica quântica. Usando o procedimento acima, os propriedades do quantum o pirazine dimethyl do thiene Methyl da laranja (MO) e do O 2,3-dimetil tieno[3,4-b] pirazina (DTP) foram investigados. O MO é um conhecido indicador de pH e pode ser encontrado sob circunstâncias básicas e acidas. Suas geometrias de mínima energia foram obtidas mediante a Teoria do Funcional da Densidade pelo funcional B3LYP, sendo o sistema descrito pelas bases de Pople com uma função de polarização (6-31G*). Para obter as propriedades médias dos observaveis, cálculos de química quântica foram executados dentro da aproximação semi-empírica de INDO/S-CI. Com respeito ao espectro de absorção, os dados experimentais existentes na literatura científica reportam a existência de uma larga banda localizada na região de baixas energias, mais precisamente entre 400 e 600 nm. Nossos resultados teóricos para a forma alcalina mostram uma transição intensa transição π → π* aproximadamente à 432.4 ± 0.03 nm e, sob condições ácidas, esta transição aparece aproximadamente à 507.4 ± 0.12, 496.4 ± 0.28 ou 545.3 ± 0.10 nm, dependendo da estrutura, mostrando bom acordo com resultados experimentais. O DTP é um sistema particular usado na produção de polímeros de baixo gap. Suas propriedades elétricas e óticas foram obtidas através de um novo procedimento conhecido por Configuração Eletrostática Média do Solvent (ASEC). O procedimento ASEC inclui moléculas do solvente como cargas pontuais e permite o obtenção das quantidades quânticas executando somente poucos cálculos de mecânica quântica. Para o DTP, usando a teoria das perturbações de segunda ordem Mφller-Plesset (MP2) e o conjunto de bases aug-cc-pVDZ, a convergência do momento de dipolo foi alcançada com apenas quatro cálculos de mecânica quântica à 1.16 D, apresentando um aumento de 42% quando comparado ao dipolo isolado. O polarizabilidade corresponde à outra característica elétrica que pôde ser medida. Considerando o mesmo nível empregado ao cálculo do dipolo, o valor médio 132.7 a30 foi observado. A região de mais baixas da energias do espectro de absorption foi investigada também atravé de procedimento de ASEC usando ambos as aproximações, semi-empírico e DFT. Esta região de absorção é motivo de conclusões contraditórias com relação à natureza das transições n → π* e π → π*. Nossos resultados mostram que realmente que essas excitações são realmente observadas simultanemente podendo sobrepôr-se. Como exemplo, nossos resultados para DFT, encontrados usando o funcional B3LYP nos mostra que estas transições aparecem aproximadamente à 360.6 e 351.1 nm.