Formation of polypyrrole and polythiophene within Cu2+- and H+-mordenite hosts studied by EPR and UV-VIS spectroscopy

The reactions of pyrrole and thiophene monomers in copper-exchanged mordenite have been investigated using EPR and UV–VIS absorption spectroscopy. The EPR spectra show a decrease in the intensity of the Cu2+ signal and the appearance of a radical signal due to the formation of oxidatively coupled oligomeric and/or polymeric species in the zeolite host. The reaction ceases when ca. 50% of the copper has reacted and differences in the form of the residual Cu2+ signal between the thiophene and pyrrole reactions suggest a greater degree of penetration of the reaction into the zeolite host for pyrrole, in agreement with previous XPS measurements. The EPR signal intensities show that the average length of the polymer chain that is associated with each radical centre is 15–20 and 5–7 monomer units for polypyrrole and polythiophene, respectively. The widths of the EPR signals suggest that these are at least partly due to small oligomers. The UV–VIS absorption spectra of the thiophene system show bands in three main regions: 2.8–3.0 eV (A), 2.3 eV (B) and 1.6–1.9 eV (D, E, F). Bands A and D–F occur in regions which have previously been observed for small oligomers, 4–6 monomer units in length. Band B is assigned to longer chain polythiophene molecules. We therefore conclude that the reaction between thiophene and copper-loaded mordenite produces a mixture of short oligomers together with some long chain polythiophene. The UV–VIS spectra of the pyrrole system show bands in the regions 3.6 eV (A), 2.7–3.0 eV (B, C) and 1.5–1.9 eV (D, F). Assignments of these bands are less certain than for the thiophene case because of the lack of literature data on the spectra of pyrrole oligomers.

Mordenite-incorporated PVA-PSSA membranes as electrolytes for DMFCs

Composite membranes with mordenite (MOR) incorporated in poly vinyl alcohol (PVA)–polystyrene sulfonic acid (PSSA) blend tailored with varying degree of sulfonation are reported. Such a membrane comprises a dispersed phase of mordenite and a continuous phase of the polymer that help tuning the flow of methanol and water across it. The membranes on prolonged testing in a direct methanol fuel cell (DMFC) exhibit mitigated methanol cross-over from anode to the cathode. The membranes have been tested for their sorption behaviour, ion-exchange capacity, electrochemical selectivity and mechanical strength as also characterized by Fourier transform infrared spectroscopy and thermogravimetric analysis. Water release kinetics has been measured by magnetic resonance imaging (NMR imaging) and is found to be in agreement with the sorption data. Similarly, methanol release kinetics studied by volume-localized NMR spectroscopy (point resolved spectroscopy, PRESS) clearly demonstrates that the dispersion of mordenite in PVA–PSSA retards the methanol release kinetics considerably. A peak power-density of 74 mW/cm2 is achieved for the DMFC using a PVA–PSSA membrane electrolyte with 50% degree of sulfonation and 10 wt.% dispersed mordenite phase. A methanol cross-over current as low as 7.5 mA/cm2 with 2 M methanol feed at the DMFC anode is observed while using the optimized composite membrane as electrolyte in the DMFC, which is about 60% and 46% lower than Nafion-117 and PVA–PSSA membranes, respectively, when tested under identical conditions.

Mordenite from Spain and its application as pozzolana

In Spain, natural zeolites have been only found in the volcanic areas of Canary Islands (San Gil, M.M., 1959). However, several years ago the study of the South Eastern region of continental Spain (Cabo de Gata) revealed the presence of a deposit of mordenite being industrially commercialized as bentonite. The deposit San José-Los Escullos is located in the concession registered as Los Murcianos, managed by Bentonitas Especiales, S.A. (BENESA) who was extracting bentonite while ignoring the presence of the zeolite. The name San José-Los Escullos refers to the discovery of mordenite in this deposit. The deposit is located in a volcanic area, constituted by pyroxenic andesites, breccias, tuffs, pyroclasts with andesitic and dacitic composition, largely altered by the hydrothermal solutions. The recent discovery of this zeolite with mordenite content up to 97%, has changed the initial vision about that deposit, and new possible uses of this mineral in the pozzolanic cement industry are foreseen. This work intends to give preliminary data on the characterization of this zeolite according to X-ray diffraction (XRD), ICP analyses, and scanning electron microscopy (SEM), as well as to emphasize the pozzolanic properties of this material, using both chemical and mechanical tests.

trans-Polyacetylene on sodium and cesium mordenites: a resonance Raman spectroscopic study

Sodium and cesium mordenite (denoted NaM and CsM, respectively) were investigated as potential catalysts for the synthesis of polyacetylene ((CH) x). Both were successful in initiating polymerization of purified gaseous acetylene at room temperature as evidenced by Raman spectroscopic studies. The polyacetylene synthesised in this way exhibited resonance enhancement of the polyene skeletal vibrations. trans-Polyacetylene, but no cis-(CH) x, was detected. As no apparent coloration of the NaM and CsM substrates accompanied the formation of trans-(CH) x it was concluded that only small quantities of the polymer were present. The number of conjugated double bonds was estimated from the frequencies of the Raman active C-C and C=C stretching vibrations, and it was shown that the trans-(CH) x formed on CsM has a distribution of conjugation lengths ranging from less than 6 to at least 30 double bonds. The polyacetylene formed on NaM was significantly shorter and was produced in lower yields than that synthesized on CsM. "Sliced" resonance excitation profiles of polyacetylene formed on CsM were obtained using nearly 40 different excitation wavelengths and these confirmed that the adsorbed trans-(CH) x was composed of segments having a distribution of conjugated lengths. The architecture of the mordenite pore system permitted only a single polymer molecule per channel, thereby preventing cross-linking. Raman spectroscopic studies of the effects of exposure to air revealed that progressive oxidative degradation occurred with a reduction in the number of conjugated double bond

Spectroscopic investigation of the polymerisation of pyrrole and thiophene within zeolite channels

The reaction of pyrrole and thiophene monomers with copper- or nickel-exchanged mordenite has been investigated using X-ray photoelectron (XPS) and photoacoustic infrared (PAIRS) spectroscopies. Because of the differing oxidising powers of the cations studied, polymerisation occurred only with copper-exchanged mordenite. PAIRS and XPS data indicated that both polypyrrole and polythiophene were partially oxidised when synthesised within the zeolite structure. IR spectra of polythiophene and polythiophene and polypyrrole showed intense bands typical of ring vibrations which could couple to the large dipole change induced by charges moving along the polythiophene chain. In addition it was noted that only vibrations typical of oxidised polymer structures were recorded, suggesting that the charge carrier was located within these segments. Furthermore, N 1s spectra contained a high binding energy peak at 402.5 eV which was attributed to a positively charged nitrogen species, in agreement with IR data. Significantly, C 1s spectra confirmed that molecular wires were formed within the confines of the zeolite lattice. Depth-profiling experiments suggested that polypyrrole was distributed throughout the entire zeolite host. By contrast, polythiophene may have been restricted to the uppermost zeolite channels owing to the ability of sulfur species to bond to CuI sites [produced by reduction of copper(II) ions during the polymerisation process], thus obstructing movement along the channels.

Towards a green synthesis of isoquinoline: Beckmann rearrangement of E,-cinnamaldoxime over H-zeolites

Isoquinoline was prepared through the Beckmann rearrangement of cinnamaldoxime over different H-zeolites, K-10 montmorillonite clay, amorphous SiO2–Al2O3 and γ-alumina under well-optimized conditions of temperature, weight hourly space velocity and catalyst loading. Cinnamaldoxime under ambient reaction conditions over the catalysts underwent migration of the anti-styryl moiety to electron deficient nitrogen (Beckmann rearrangement) followed by an intramolecular cyclization to yield isoquinoline. Cinnamo-nitrile (dehydration product) and cinnamaldehyde were formed as by-products. Isoquinoline formation was high on zeolite catalysts (ca. >86.5%) and mordenite (ca. 92.3%) was the most efficient in the series. Catalysts were susceptible for deactivation and the decrease in the percentage conversion of oxime with time is associated with a corresponding increase in the acid hydrolysis producing salicylaldehyde at later stages of the reaction. However, these catalysts retain activity considerably and can be recycled without loss of activity and change of product distribution.

Criação de mesoporos em zeólitas ZSM-5, mordenita e ferrierita e análise de seu efeito na reação de hidroisomerização do n-heptano

As zeólitas têm recebido grande atenção acadêmica e industrial devido às suas características ácidas e estruturais. A estrutura da zeólita pode ser utilizada para conduzir uma reação catalítica na direção do produto desejado, evitando assim reações paralelas. Porém, essa mesma estrutura cria restrições difusivas com relação ao acesso aos sítios ativos no interior dos microporos. Neste trabalho foram estudados dois métodos de criação de mesoporos (térmico e básico) com o intuito de modificar a acessibilidade aos sítios catalíticos das zeólitas. A reação de hidroisomerização do n-heptano foi selecionada para avaliar as zeólitas após a criação de mesoporosidade. O tratamento térmico (via calcinação em temperaturas elevadas) foi utilizado para as zeólitas do tipo ZSM-5, Mordenita e Ferrierita, tendo sido observado um aumento pouco significativo na mesoporosidade. Este tratamento promoveu, porém, uma significativa desaluminização das amostras, acompanhada da formação de quantidades importantes de espécies de Al extra-rede (ALER), o que se refletiu num bloqueio parcial dos mesoporos gerados e dos microporos preexistentes, e na redução na densidade de sítios ácidos das amostras. A ampliação da escala do tratamento térmico (aumento da quantidade tratada de 2 g para 30 g) não se mostrou reprodutível, gerando menos mesoporos do que o observado no preparo em pequena escala. O tratamento básico (via dessilicação por meio de NaOH), ao contrário do anterior, promoveu a formação de mesoporos gerando menos quantidade de ALER e se mostrou mais reprodutível quando da ampliação da escala. O desempenho dos catalisadores Pt/Al2O3+zeólita na reação de hidroisomerização do n-heptano foi influenciado pela densidade de sítios ácidos fortes e pela estrutura porosa da zeólita. Com relação ao efeito dos tratamentos térmico e básico sobre o desempenho dos catalisadores à base de ZSM-5, os resultados mostraram que o comportamento do catalisador submetido ao tratamento básico (Pt/Al2O3+BZSM-5/85-2) foi similar ao do tratado termicamente (Pt/Al2O3+TZSM-5/1000-2) com relação à distribuição de produtos na reação de hidroisomerização do n-heptano, particularmente com relação aos produtos leves e aos isômeros monorramificados. No entanto, a presença mais significativa de mesoporos na zeólita após tratamento básico (BZSM-5/85-2), se refletiu num leve favorecimento à formação dos isômeros birramificados