Synthesis of electrically conducting copolymers of aniline with o/m-amino benzoic acid by an inverse emulsion pathway

Copolymers of aniline and ortholmeta-amino benzoic acid were synthesized by chemical polymerization using an inverse emulsion pathway. The copolymers are soluble in organic solvents, and the solubility increases with the amino benzoic acid content in the feed. The reaction conditions were optimized with emphasis on high yield and relatively good conductivity (2.5 X 10(-1) S cm(-1)). The copolymers were characterized by a number of techniques including UV-vis, FT-IR, FT-Raman, EPR and NNM spectroscopy, thermal analysis, SEM and conductivity. The influence of the carboxylic acid group ring substituent on the copolymers is investigated. The spectral studies reveal that the amino benzoic acid groups restrict the conjugation along the polymer chain. The SEM micrographs of the copolymers reveal regions of amorphous and crystalline domain. Thermal studies indicate a marginally higher thermal stability for poly(aniline-co-m-amino benzoic acid) compared to poly(aniline-co-o-amino benzoic acid). (C) 2002 Elsevier Science Ltd. All rights reserved.

Synthesis of electrically conducting copolymers of o-/m-toluidines and o-/m-amino benzoic acid in an organic peroxide system and their characterization

Copolymers of o-lm-toluidine with o-lm-amino benzoic acid have been synthesized by chemical polymerization using inverse emulsion pathway and characterized by a number of techniques including UV-Vis, FT-IR, FT Raman, EPR and NMR spectroscopies, thermal analysis and conductivity. The solubility of the copolymers in organic solvents increases with increase in the amount of amino benzoic acid in the feed. The copolymers synthesized at room temperature show relatively higher conductivity and are obtained in higher yield compared to those synthesized at 0 and 60 degreesC. The spectral studies have revealed restricted conjugation along the polymer chain. The effect of -COOH substituent on the copolymer structure is discussed. (C) 2003 Elsevier Science B.V All rights reserved.

Preparation of Polyacrylamide Aqueous Dispersions Using Poly(sodium acrylic acid) as Stabilizer

High-solids, low-viscosity, stable polyacrylamide (PAM) aqueous dispersions were prepared by dispersion polymerization of acrylamide in aqueous solution of ammonium sulfate (AS) using Poly (sodium acrylic acid) (PAANa) as the stabilizer, ammonium persulfate (APS) or 2,2'-Azobis (N,N'-dimethyleneisobutyramidine) dihydrochloride (VA-044) as the initiator. The molecular weight of the formed PAM, ranged from 710, 000 g/mol to 4,330,000 g/mol, was controlled by the addition of sodium formate as a conventional chain-transfer agent. The progress of a typical AM dispersion polymerization was monitored with aqueous size exclusion chromatography. The influences, of the AS concentration, the poly(sodium acrylic acid) concentration, the initiator type and concentration, the chain-transfer agent concentration and temperature Oil the monomer conversion, the dispersion viscosity, the PAM molecular weight and distribution, the particle size and morphology were systematically investigated.

Preparation of poly(acrylamide-co-acrylic acid) aqueous latex dispersions using anionic polyelectrolyte as stabilizer

High-solids, low-viscosity, stable poly(acrylamide-co-acrylic acid) aqueous latex dispersions were prepared by the dispersion polymerization of acrylamide (AM) and acrylic acid (AA) in an aqueous solution of ammonium sulfate (AS) medium using anionic polyelectrolytes as stabilizers. The anionic polyelectrolytes employed include poly(2-acrylamido-2-methylpropanesulfonic acid sodium) (PAMPSNa) homopolymer and random copolymers of 2-acrylamido-2-methylpropanesulfonic acid sodium (AMPSNa) with methacrylic acid sodium (MAANa), acrylic acid sodium (AANa) or acrylamide (AM). The influences of stabilizer's structure, composition, molecular weight and concentration, AA/AM molar feed ratio, total monomer, initiator and aqueous solution of AS concentration, and stirring speed on the monomer conversion, the particle size and distribution, the bulk viscosity and stability of the dispersions, and the intrinsic viscosity of the resulting copolymer were systematically investigated. Polydisperse spherical as well as ellipsoidal particles were formed in the system. The broad particle size distributions indicated that coalescence of the particles takes place to a greater extent.

Constribuição técnica de um sistema de emulsão inversa a base de óleos vegetais para fluidos de perfuração

The developments in formulating drilling fluids to apply in petroleum fields are based on new technologies and environmental challenges, where the technical performance of a developed drilling fluid is used to produce a minimum environmental impact, showing great economy in costs. It is well known that the potential use of oil-based drilling fluids is limited because these fluids when discharged in the sea do not disperse as much as water-based ones and may form waterproof films in the seabed, having a profound effect on plants and animals living in this environment. The current works have been made in investigating fluids called pseudofluids, which are synthetic ester-based, n-paraffin-based and other fluids formed from inverse emulsion. In this research the principal parameters involved in inverse emulsion process were studied, in laboratory scale, using esters as main component. Others commercial drilling fluids were used as comparative samples, as well as samples from laboratory and field where these drilling fluids are being applied. Concentrations of emulsifier and organophilic clay, which are viscosity donor, were varied to verify the influence of these parameters, in different oil/water ratios (55/45, 60/40, 65/35, 70/30, and 75/25). The salt concentration (NaCl) is an indicative parameter of stability and activity of an esterbased fluid. In this research the salt concentration was varied in 10,000, 20,000, and 50,000 ppm of NaCl. Some rheological properties of the produced fluids were studied, such as: initial gel, plastic viscosity, yield point, and apparent viscosity. Through the obtained rheological measures, the existence of two systems could be verified: fluid and flocculated. It could be noticed that the systems were influenced, directly, by the oil/water ratio and emulsifier, organophilic clay and NaCl concentrations. This study showed the viability to use an ester obtained from a regional vegetable product babaçu coconut oil to obtain an efficient and environmental safe drilling fluid

Fluorenbasierende amphiphile Kammpolymere zur Ausbildung definierter Strukturen an Oberflächen und in Lösungen

Die Dissertation beschreibt die Darstellung und Charakterisierung von neuartigen, amphiphilen Carbazol- und Fluoren-(co)-polymeren, die infolge ihres strukturellen Aufbaus sowohl selbstorganisierende als auch optoelektronische Eigenschaften kombinierten. Zum einen wurden Kammpolymere mit konjugierten, steifen Rückgraten und flexiblen sowie konformativ schaltbaren Polyelektrolytseitenketten dargestellt und auf eine pH-abhängige Selbstorganisation in Lösung und an Oberflächen untersucht. Des Weiteren wurden neutrale, methanollösliche Polyfluorene synthetisiert, die in Kombination mit einem unpolaren Polyindenofluorenderivat zum Aufbau mehrschichtiger PLEDs mittels nasschemischer Verfahren eingesetzt wurden. Zum anderen fand die Synthese von amphiphilen Polyfluorenen statt, die als Emulgatoren zur Stabilisierung von inversen Emulsionen eingesetzt wurden. Dabei konnten mit Hilfe eines bereits für die Darstellung von anorganisch-organischen Kern-Schale-Partikeln etablierten in situ-Verfahrens formanisotrope, kristalline Zinkoxidkerne mit konjugierter Polymerhülle erhalten werden.

Kontrolle der Grenzflächeneigenschaften anorganischer Nanopartikel mittels amphiphiler Polymere

Im Rahmen dieser Arbeit wurden amphiphile Co- und Terpolymere verwendet, um die Grenzflächeneigenschaften anorganischer Nanopartikel zu kontrollieren. Es wurde eine effiziente und vielseitige Methode entwickelt, mit der in-situ hydrophobierte, formanisotrope ZnO-, CdS- und Au-Nanopartikel sowie poröse TiO2-Nanopartikel hergestellt werden konnten. Diese Technik basierte auf der Fällung anorganischer Nanopartikel in einer inversen Emulsion mittels kombinierten Einsatzes zweier maßgeschneiderter amphiphiler Polymere. Ein Copolymer ermöglichte sowohl die Stabilisierung der Emulsion als auch die Hydrophobierung der Partikel, und ein weiteres Struktur-dirigierendes Agens (SDA) kontrollierte den Kristallisationsprozess. Infolge ihrer Form zeigten die Nanopartikel von sphärischen Teilchen abweichende Lagen der Oberflächenplasmonenresonanz und der Bandlücke. Aufgrund der hervorragenden Hydrophobierung dieser Kolloide mittels amphiphiler Copolymere konnten diese homogen in polymere Materialien eingearbeitet werden. Dies erlaubte es die speziellen Eigenschaften von nicht-sphärischen Kolloiden auf Nanokompositmaterialien zu übertragen. Darüber hinaus wurden amphipolare Copolymere genutzt, um superhydrophobe Oberflächen zu generieren. Hierzu wurden Filme bestehend aus rauen SiO2-Nanopartikeln mit fluorierten Emulgatoren beschichtet. In einem dritten Schwerpunkt dieser Arbeit wurden amphiphile Co- und Terpolymere verwendet, um anorganische Nanopartikel zu hydrophilieren. Durch Variation der Emulgatorzusammensetzung konnten die Ladung und Ladungsdichte auf der Partikeloberfläche gezielt gesteuert werden. Darüber hinaus konnte die Partikelhülle zusätzlich mit Farbstoffmolekülen funktionalisiert werden, was den erfolgreichen Einsatz der Kolloide in Zellaufnahmeexperimenten ermöglichte.

Herstellung hydrophiler Polyurethanpartikel und anisotroper Polymerpartikel

Hydrophile Polyurethanpartikel wurden mittels in inversen Miniemulsionen durchgeführten Polyadditionsreaktionen hergestellt. Wie durch FT-IR-Spektroskopie gezeigt wurde, konnte durch die Abwesenheit von Wasser in dem verwendeten System die Entstehung von Harnstoffbindungen vermieden werden. Das Molekulargewicht der erhaltenen Polyurethane konnte durch verschiedene Parameter, wie zum Beispiel die Hydrophobizität der kontinuierlichen Phase oder die Zugabe von DMSO zur dispersen Phase, beeinflusst werden. Die höchsten Molekulargewichte (Mn von bis zu 19000 g•mol-1) wurden mit Isopar M als kontinuierlicher Phase erhalten. Der zweite Teil der Arbeit beschäftigt sich mit der Herstellung anisotroper Polystyrolpartikel über eine Film-Dehnungs-Methode. Polystyrol/Polyvinylalkohol-Filme wurden oberhalb der Glasübergangstemperatur von Polystyrol und Polyvinylalkohol (Matrix) uniaxial oder biaxial gedehnt, wodurch ellipsenförmige oder scheibenförmige Partikel entstanden. Es zeigte sich, dass die Redispergierbarkeit der verstreckten Partikel in Wasser stark von deren Oberflächenfunktionalisierung abhängig war. Die beste Redispergierbarkeit (46%) wurde für Sulfonat-funktionalisierte Partikel erhalten. Als eine alternative Methode zur Herstellung anisotroper Polymerpartikel wurde im letzten Teil der vorliegenden Arbeit Elektrospinnen eingesetzt. Es konnte gezeigt werden, dass es prinzipiell möglich ist, ellipsenförmige PS-Partikel zu erhalten, deren Aspektverhältnis durch die Höhe der angelegten Spannung und den Abstand zwischen Spitze und Kollektor beeinflusst wurde. Neben PS-Partikeln konnten auch PMMA-Kapseln über Elektrospinnen verstreckt werden. Mittels der Film-Dehnungs-Methode konnte jedoch eine größere Vielfalt an Aspektverhältnissen hergestellt werden. Ein weiterer Nachteil gegenüber der Film-Dehnungs-Methode ist die relativ breite Größenverteilung der verstreckten Partikel. Jedoch ist Elektrospinnen im Gegensatz zur Film-Dehnungs-Methode ein kontinuierlicher Prozess und könnte auch für die Herstellung anisotroper Partikel von Polymeren mit einer hohen Glasübergangstemperatur verwendet werden.

Water-in-Oil Micro-Emulsion Enhances the Secondary Structure of a Protein by Confinement

A scheme is presented in which an organic solvent environment in combination with surfactants is used to confine a natively unfolded protein inside an inverse microemulsion droplet. This type of confinement allows a study that provides unique insight into the dynamic structure of an unfolded, flexible protein which is still solvated and thus under near-physiological conditions. In a model system, the protein osteopontin (OPN) is used. It is a highly phosphorylated glycoprotein that is expressed in a wide range of cells and tissues for which limited structural analysis exists due to the high degree of flexibility and large number of post-translational modifications. OPN is implicated in tissue functions, such as inflammation and mineralisation. It also has a key function in tumour metastasis and progression. Circular dichroism measurements show that confinement enhances the secondary structural features of the protein. Small-angle X-ray scattering and dynamic light scattering show that OPN changes from being a flexible protein in aqueous solution to adopting a less flexible and more compact structure inside the microemulsion droplets. This novel approach for confining proteins while they are still hydrated may aid in studying the structure of a wide range of natively unfolded proteins.

An inverse time admittance relay for fault detection in distribution networks containing DGs

Isolation of a faulted segment, from either side of a fault, in a radial feeder that has several converter interfaced DGs is a challenging task when current sensing protective devices are employed. The protective device, even if it senses a downstream fault, may not operate if fault current level is low due to the current limiting operation of converters. In this paper, a new inverse type relay is introduced based on line admittance measurement to protect a distribution network, which has several converter interfaced DGs. The basic operation of this relay, its grading and reach settings are explained. Moreover a method is proposed to compensate the fault resistance such that the relay operation under this condition is reliable. Then designed relay performances are evaluated in a radial distribution network. The results are validated through PSCAD/EMTDC simulation and MATLAB calculations.

Load during prosthetic gait : is direct measurement better than inverse dynamics?

The knee forces and moments estimated by inverse dynamics and directly measured by a multiaxial transducer were compared during the gait of a transfemoral amputee. The estimated and directly measured forces and moments were relatively close. However, 3D inverse dynamics estimated only partially the forces and moments associated with the deformation of the prosthetic foot and locking of knee mechanism.

Loading applied on prosthetic knee of transfemoral amputee: comparison of inverse dynamics and direct measurements

Inverse dynamics is the most comprehensive method that gives access to the net joint forces and moments during walking. However it is based on assumptions (i.e., rigid segments linked by ideal joints) and it is known to be sensitive to the input data (e.g., kinematic derivatives, positions of joint centres and centre of pressure, inertial parameters). Alternatively, transducers can be used to measure directly the load applied on the residuum of transfemoral amputees. So, the purpose of this study was to compare the forces and moments applied on a prosthetic knee measured directly with the ones calculated by three inverse dynamics computations - corresponding to 3 and 2 segments, and « ground reaction vector technique » - during the gait of one patient. The maximum RMSEs between the estimated and directly measured forces (i.e., 56 N) and moment (i.e., 5 N.m) were relatively small. However the dynamic outcomes of the prosthetic components (i.e., absorption of the foot, friction and limit stop of the knee) were only partially assessed with inverse dynamic methods.

Effect of inaccuracies in anthropometric data and linked-segment inverse dynamic modeling on kinetics of gait in persons with partial foot amputation

The accuracy of data derived from linked-segment models depends on how well the system has been represented. Previous investigations describing the gait of persons with partial foot amputation did not account for the unique anthropometry of the residuum or the inclusion of a prosthesis and footwear in the model and, as such, are likely to have underestimated the magnitude of the peak joint moments and powers. This investigation determined the effect of inaccuracies in the anthropometric input data on the kinetics of gait. Toward this end, a geometric model was developed and validated to estimate body segment parameters of various intact and partial feet. These data were then incorporated into customized linked-segment models, and the kinetic data were compared with that obtained from conventional models. Results indicate that accurate modeling increased the magnitude of the peak hip and knee joint moments and powers during terminal swing. Conventional inverse dynamic models are sufficiently accurate for research questions relating to stance phase. More accurate models that account for the anthropometry of the residuum, prosthesis, and footwear better reflect the work of the hip extensors and knee flexors to decelerate the limb during terminal swing phase.