Three-dimensional modeling of biomass fuel flow in a circulating fluidized bed furnace

The reduction of greenhouse gas emissions in the European Union promotes the combustion of biomass rather than fossil fuels in energy production. Circulating fluidized bed (CFB) combustion offers a simple, flexible and efficient way to utilize untreated biomass in a large scale. CFB furnaces are modeled in order to understand their operation better and to help in the design of new furnaces. Therefore, physically accurate models are needed to describe the heavily coupled multiphase flow, reactions and heat transfer inside the furnace. This thesis presents a new model for the fuel flow inside the CFB furnace, which acknowledges the physical properties of the fuel and the multiphase flow phenomena inside the furnace. This model is applied with special interest in the firing of untreated biomass. An experimental method is utilized to characterize gas-fuel drag force relations. This characteristic drag force approach is developed into a gas-fuel drag force model suitable for irregular, non-spherical biomass particles and applied together with the new fuel flow model in the modeling of a large-scale CFB furnace. The model results are physically valid and achieve very good correspondence with the measurement results from large-scale CFB furnace firing biomass. With the methods and models presented in this work, the fuel flow field inside a circulating fluidized bed furnace can be modeled with better accuracy and more efficiently than in previous studies with a three-dimensional holistic model frame.

Otimização do Funcionamento de Caldeiras Aquatubulares em Indústria de Processo Químico

O presente trabalho centrou-se na otimização do rendimento térmico de duas caldeiras aquatubulares da empresa RAR- Refinaria de Açúcar Reunidas, com a finalidade de identificar onde ocorrem perdas de energia e, desta forma, propor soluções para a sua minimização. Para tal, realizaram-se ensaios em duas caldeiras da empresa providas de queimadores mistos, ou seja podem operar com fuelóleo e gás natural, tanto individualmente, como simultaneamente, sendo que para a realização dos ensaios apenas se utilizou o fuelóleo devido ao seu menor custo. Na caldeira designada por 1 realizaram-se ensaios para os caudais de 300, 500, 800, 1000, 1200, 1400 e 1600 kg/h de fuelóleo. A gama de rendimentos térmicos obtida foi entre 88,3 e 91,2%. Na caldeira designada por 3, efetuaram-se ensaios para os caudais de fuelóleo de 300, 500, 700, 900, 1000, 1200, 1400, 1500 e 1800 kg/h e os rendimentos térmicos obtidos foram entre 85,2 e 88,0%. Em ambas as caldeiras e para caudais baixos verificou-se que a quantidade de ar introduzida no processo de combustão era superior à necessária, conduzindo a uma diminuição dos valores de rendimento térmico. Para 500 kg/h de fuelóleo, por exemplo, a quantidade de ar utilizada foi cerca de duas vezes superiores ao valor estequiométrico. Tendo em conta estes factos, foi proposto ao gestor de energia a implementação de uma nova relação de ar/combustível vs caudal de combustível no sistema de controlo das referidas caldeiras. Após alguns testes (excluindo 300 kg/h de fuelóleo devido a questões de operação), considerou-se como caudal mínimo de operação os 500 Kg/h de fuelóleo nas respetivas caldeiras 1 e 3. Verificou-se que os rendimentos térmicos aumentaram, no caso da caldeira 1, para valores entre os 90,1 e 91,3% e, na caldeira 3, para valores entre 89,0 e 90,9%. Por fim, efetuou-se uma breve análise económica com o intuito de se avaliar e quantificar o que a empresa pode poupar com esta medida. O lucro anual pode oscilar entre 14.400 e 62.640€ ou 104.400 e 136.800€, para as caldeiras 1 e 3, respetivamente.

Optimisation of data analysis method for a fluidized bed combustion test rig

Nowadays the used fuel variety in power boilers is widening and new boiler constructions and running models have to be developed. This research and development is done in small pilot plants where more faster analyse about the boiler mass and heat balance is needed to be able to find and do the right decisions already during the test run. The barrier on determining boiler balance during test runs is the long process of chemical analyses of collected input and outputmatter samples. The present work is concentrating on finding a way to determinethe boiler balance without chemical analyses and optimise the test rig to get the best possible accuracy for heat and mass balance of the boiler. The purpose of this work was to create an automatic boiler balance calculation method for 4 MW CFB/BFB pilot boiler of Kvaerner Pulping Oy located in Messukylä in Tampere. The calculation was created in the data management computer of pilot plants automation system. The calculation is made in Microsoft Excel environment, which gives a good base and functions for handling large databases and calculations without any delicate programming. The automation system in pilot plant was reconstructed und updated by Metso Automation Oy during year 2001 and the new system MetsoDNA has good data management properties, which is necessary for big calculations as boiler balance calculation. Two possible methods for calculating boiler balance during test run were found. Either the fuel flow is determined, which is usedto calculate the boiler's mass balance, or the unburned carbon loss is estimated and the mass balance of the boiler is calculated on the basis of boiler's heat balance. Both of the methods have their own weaknesses, so they were constructed parallel in the calculation and the decision of the used method was left to user. User also needs to define the used fuels and some solid mass flowsthat aren't measured automatically by the automation system. With sensitivity analysis was found that the most essential values for accurate boiler balance determination are flue gas oxygen content, the boiler's measured heat output and lower heating value of the fuel. The theoretical part of this work concentrates in the error management of these measurements and analyses and on measurement accuracy and boiler balance calculation in theory. The empirical part of this work concentrates on the creation of the balance calculation for the boiler in issue and on describing the work environment.

Polttoaineiden vastaanotonja käytön tarkastelu ja optimointi biopolttoaineita käyttävässä voimalaitoksessa

Kioton pöytäkirja velvoittaa teollisuusmaita vähentämään hiilidioksidipäästöjään. Energiantuotantolaitosten on vähennettävä tuotantoaan tai siirryttävä käyttämään vähäpäästöisempiä polttoaineita vähennystavoitteiden saavuttamiseksi. Etelä-Savon Energia Oy Mikkelissä rakentaa uuden kattilalaitoksen, joka soveltuu hiilidioksidivapaiden puupolttoaineiden polttoon. Kun uusi kattilalaitos otetaan käyttöön, kasvaa voimalaitoksen polttoaineiden kulutus 1,7 -kertaiseksi. Tämä merkitsee laitokselle tulevien polttoainekuljetusten määrän kasvamista kylmimpinä aikoina yli 70:neen autoon vuorokaudessa. Työssä on tarkasteltu nykyisen polttoaineiden vastaanoton ja kuljettimien kykyä ottaa vastaan kasvavat polttoainevirrat. Vastaanoton sujuvuus on polttoaineiden laadunhallinnan lisäksi edellytys laitoksen käytölle. Työn tavoitteena on ollut kartoittaa vastaanoton ongelmakohtia ja löytää näihin parannusmahdollisuuksia. Vastaanottokapasiteetti tulee venymään äärimmilleen tulevaisuudessa. Jotta määrällisesti riittävä ja laadullisesti sopiva polttoaineseos saadaan vastaanotettua nykyisenä vastaanottoaikana, tulee autojen saapua entistä tasaisemmin laitokselle. Tasainen saapuminen on mahdollista aikatauluttamalla sopivasti polttoainekuljetusten saapumisajat laitokselle. Vastaanoton kapasiteettia voitaisiin nostaa kasvattamalla kenttävaraston kokoa ja pienillä muutoksilla vastaanottoasemissa. Polttoaineen laadun ja vastaanoton tarkastelun lisäksi työssä on tarkasteltu polttoaineen saatavuutta.

Kaasuturbiinin polttoainesuuttimien virtausmittaus

Tässä diplomityössä suunniteltiin ja rakennettiin kaasuturbiinin kaasusuuttimien virtausmittauslaitteisto. Suuttimien epätasainen toiminta kasvattaa kaasuturbiinin poistolämpötilahajontaa. Virtausmittauksien perusteella voidaan määrittää suuttimien efektiivinen virtauspoikkipinta-ala. Suuttimien asennusjärjestys opti-moidaan suuttimien välisten pinta-alaerojen mukaisesti, jolloin polttoainevirtaus polttokammioihin on mahdollisimman tasainen ja poistolämpötilahajonta pienenee. Kaasuturbiinin MS6001 esittelyssä keskityttiin tärkeimpiin komponentteihin sekä polttoainesuuttimien testauksen kannalta oleellisiin osiin ja niiden toimintaan. Teoriaosuudessa tarkasteltiin tilavuusvirran sekä suutinvirtauksen laskennassa käytettäviä yhtälöitä. Mittalaitteiston suunnittelu ja toteutus olivat tämän työn laajin osa-alue. Laitteiston keskeiset osat ovat kuristuselin ja suutintestausosa. Kuristuselintyypiksi valittiin rengaskammiollinen kuristuslaippa, joka suun-niteltiin standardin SFS-EN ISO 5167:2003 mukaisesti. Standardissa annettujen yhtälöiden antamia tuloksia verrattiin numeerisella virtauslaskentamallilla lasket-tuihin tuloksiin. Suutinrunkojen ja -kärkien mittauksien suunnittelussa sovellettiin samaa standardia sekä numeerista virtauslaskentaa optimaalisen sijainnin löytämiseksi paineyhteelle. Mittauksissa syntyvien epävarmuuksien arviointiin kiinnitettiin erityistä huomiota. Kokeellisessa osuudessa mitattiin yhden kunnostetun suuttimen, käytetyn suut-timen ja suutinrungon virtausta. Tuloksien perusteella laskettiin efektiiviset pinta-alat, joita verrattiin turbiinivalmistajan ilmoittamiin pinta-aloihin. Lopuksi arvioitiin mittaustulosten perusteella laitteiston toimivuutta. Virhe-arvioinnin ja mittaustulosten perusteella laadittiin teknisiä parannusehdotuksia suutintestauslaitteiston luotettavan toiminnan varmistamiseksi.

Design and development of a low NOx Coanda ejector burner

Small gaseous combustion systems are being targeted by strict pollution legislation which will provide challenges to reduce the NOx being emitted. A novel type of gas burner has been successfully designed and developed which incorporates a Coanda ejector to promote recirculation of flue gas from the burner exit. This provides a combustion system which gives very low emissions of NOx and CO, whilst maintaining a high degree of flame stability over a range of air/fuel ratios and fuel flow rates. Recirculation of flue gas was obtained by manipulating the aerodynamics of the system, without the aid of external duct work or moving parts. The design of the burner allowed very low pollutant emissions near stoichiometric conditions, resulting in high temperatures of the exit gas. Potential applications of this type of burner are in small and intermediate furnaces where low NOx emissions are required. Moreover, very high-temperature applications, such as glass furnaces could benefit in both cost and pollutant emissions from such a burner.

Performance and emissions of a gas turbine engine using ox tallow ethyl-ester blended with kerosene

The performance and emissions behavior of a Rover 1S/60 turboshaft engine when operated with several blends of aviation kerosene and ox tallow ethyl-ester are shown in this article. The tests were performed with a compressor shaft coupled to an hydraulic dynamometer where data of power and mass fuel flow were collected to determine the brake specific fuel consumption. A flue gas analyzer was positioned at the exhaust duct to collect oxygen, carbon dioxide, carbon monoxide and nitrous oxides. An increase in the specific fuel consumption was observed due to the lesser lower heating value of the most oxygenated blends. However, reductions of CO, CO2 and NO (x) have been observed and no-significant ill effects have occurred in the turbine operation.

Impact of E22 on two-stroke and four-stroke snowmobiles

A push to reduce dependency on foreign energy and increase the use of renewable energy has many gas stations pumping ethanol blended fuels. Recreational engines typically have less complex fuel management systems than that of the automotive sector. This prevents the engine from being able to adapt to different ethanol concentrations. Using ethanol blended fuels in recreational engines raises several consumer concerns. Engine performance and emissions are both affected by ethanol blended fuels. This research focused on assessing the impact of E22 on two-stroke and four-stroke snowmobiles. Three snowmobiles were used for this study. A 2009 Arctic Cat Z1 Turbo with a closed-loop fuel injection system, a 2009 Yamaha Apex with an open-loop fuel injection system and a 2010 Polaris Rush with an open-loop fuel injection system were used to determine the impact of E22 on snowmobile engines. A five mode emissions test was conducted on each of the snowmobiles with E0 and E22 to determine the impact of the E22 fuel. All of the snowmobiles were left in stock form to assess the effect of E22 on snowmobiles currently on the trail. Brake specific emissions of the snowmobiles running on E22 were compared to that of the E0 fuel. Engine parameters such as exhaust gas temperature, fuel flow, and relative air to fuel ratio (λ) were also compared on all three snowmobiles. Combustion data using an AVL combustion analysis system was taken on the Polaris Rush. This was done to compare in-cylinder pressures, combustion duration, and location of 50% mass fraction burn. E22 decreased total hydrocarbons and carbon monoxide for all of the snowmobiles and increased carbon dioxide. Peak power increased for the closed-loop fuel injected Arctic Cat. A smaller increase of peak power was observed for the Polaris due to a partial ability of the fuel management system to adapt to ethanol. A decrease in peak power was observed for the open-loop fuel injected Yamaha.

Caracterização experimental de uma bomba ejetora

A opção de futuro incide sobre os processos de combustão em regime pobre e com baixos índices de formação de poluentes. Neste contexto, o presente trabalho estuda um ejetor de um queimador de gás propano, que equipa uma marmita utilizada para confeção de alimentos no Exército Português, para compreender o mecanismo de arrastamento de ar, com vista a identificar as causas que possam contribuir para uma diminuição da razão de equivalência da mistura ar/combustível. Estes queimadores são dispositivos de funcionamento estritamente mecânico e de conceção simples que permitem uma gama de potências caloríficas compreendidas entre 8 e 22 kW. Permitem uma boa estabilidade de chama que é um requisito fundamental de segurança. A regulação de potência é executada através de uma válvula de ajuste, contendo três posições, uma em que a alimentação se encontra cortada e as outras duas permitindo funcionar na potência mínima e máxima. De modo a efetuar o estudo do ejetor, numa primeira fase, submeteu-se o sistema a uma caracterização experimental do campo de escoamentos à entrada de ar do ejetor, a partir da técnica de diagnóstico Particle Image Velocimetry (PIV). Assim avalia-se de que forma o escoamento de ar exterior influencia o comportamento do escoamento da mistura de ar/combustível à saída do queimador. Numa segunda fase, recorre-se à técnica de diagnóstico Quimiluminescência para medição de espécies químicas, para avaliar o comportamento do ejetor a alterações de vários parâmetros, tais como caudal de combustível, área de entrada de ar e área de saída da mistura do difusor. Conclui-se que o ejetor mostrase "insensível" a alterações da área de saída e de entrada de ar, em relação ao valor médio da razão de equivalência. Porém observa-se que as misturas de ar/combustível são mais homogéneas quando as áreas de entrada, da saída e da garganta têm valores próximos.

Measurement of the aerodynamic performance of a scramjet-powered vehicle in a shock tunnel

A force balance system for measuring lift, thrust and pitching moment has been used to measure the performance of fueled scramjet-powered vehicle in the T4 Shock Tunnel at The University of Queensland. Detailed measurements have been made of the effects of different fuel flow rates corresponding to equivalence ratios between 0.0 and 1.5. For proposed scramjet-powered vehicles, the fore-body of the vehicle acts as part of the inlet to the engine and the aft-body acts as the thrust surface for the engine. This type of engine-integrated design leads to a strong coupling between the performance of the engine and the lift and trim characteristics of the vehicle. The measurements show that the lift force increased by approximately 50% and centre-of-pressure changed by approximately 10% of the chord of the vehicle when the equivalence ratio varied from 0.0 to 1.0. The results demonstrate the importance of engine performance to the overall aerodynamic characteristics of engine-integrated scramjet vehicles and that such characteristics can be measured in a shock tunnel.

Soot measurements in steady and pulsed ethylene/air diffusion flames using Laser-Induced Incandescence

Combustion-generated carbon black nano particles, or soot, have both positive and negative effects depending on the application. From a positive point of view, it is used as a reinforcing agent in tires, black pigment in inks, and surface coatings. From a negative point of view, it affects performance and durability of many combustion systems, it is a major contributor of global warming, and it is linked to respiratory illness and cancer. Laser-Induced Incandescence (LII) was used in this study to measure soot volume fractions in four steady and twenty-eight pulsed ethylene diffusion flames burning at atmospheric pressure. A laminar coflow diffusion burner combined with a very-high-speed solenoid valve and control circuit provided unsteady flows by forcing the fuel flow with frequencies between 10 Hz and 200 Hz. Periodic flame oscillations were captured by two-dimensional phase-locked LII images and broadband luminosity images for eight phases (0° – 360°) covering each period. A comparison between the steady and pulsed flames and the effect of the pulsation frequency on soot volume fraction in the flame region and the post flame region are presented. The most significant effect of pulsing frequency was observed at 10 Hz. At this frequency, the flame with the lowest mean flow rate had 1.77 times enhancement in peak soot volume fraction and 1.2 times enhancement in total soot volume fraction; whereas the flame with the highest mean flow rate had no significant change in the peak soot volume fraction and 1.4 times reduction in the total soot volume fraction. A correlation (fvRe-1 = a + b·Str) for the total soot volume fraction in the flame region for the unsteady laminar ethylene flames was obtained for the pulsation frequency between 10 Hz and 200 Hz, and the Reynolds number between 37 and 55. The soot primary particle size in steady and unsteady flames was measured using the Time-Resolved Laser-Induced Incandescence (TIRE-LII) and the double-exponential fit method. At maximum frequency (200 Hz), the soot particles were smaller in size by 15% compared to the steady case in the flame with the highest mean flow rate.

Soot Measurements in Steady and Pulsed Ethylene/Air Diffusion Flames Using Laser-Induced Incandescence

Combustion-generated carbon black nano particles, or soot, have both positive and negative effects depending on the application. From a positive point of view, it is used as a reinforcing agent in tires, black pigment in inks, and surface coatings. From a negative point of view, it affects performance and durability of many combustion systems, it is a major contributor of global warming, and it is linked to respiratory illness and cancer. Laser-Induced Incandescence (LII) was used in this study to measure soot volume fractions in four steady and twenty-eight pulsed ethylene diffusion flames burning at atmospheric pressure. A laminar coflow diffusion burner combined with a very-high-speed solenoid valve and control circuit provided unsteady flows by forcing the fuel flow with frequencies between 10 Hz and 200 Hz. Periodic flame oscillations were captured by two-dimensional phase-locked LII images and broadband luminosity images for eight phases (0°- 360°) covering each period. A comparison between the steady and pulsed flames and the effect of the pulsation frequency on soot volume fraction in the flame region and the post flame region are presented. The most significant effect of pulsing frequency was observed at 10 Hz. At this frequency, the flame with the lowest mean flow rate had 1.77 times enhancement in peak soot volume fraction and 1.2 times enhancement in total soot volume fraction; whereas the flame with the highest mean flow rate had no significant change in the peak soot volume fraction and 1.4 times reduction in the total soot volume fraction. A correlation (ƒv Reˉ1 = a+b· Str) for the total soot volume fraction in the flame region for the unsteady laminar ethylene flames was obtained for the pulsation frequency between 10 Hz and 200 Hz, and the Reynolds number between 37 and 55. The soot primary particle size in steady and unsteady flames was measured using the Time-Resolved Laser-Induced Incandescence (TIRE-LII) and the double-exponential fit method. At maximum frequency (200 Hz), the soot particles were smaller in size by 15% compared to the steady case in the flame with the highest mean flow rate.

Determination of sulfate in ethanol fuel using an electrode chemically modified with polypyrrole by flow injection analysis

In this work, an electrode chemically modified with polypyrrole (PCME) was employed for determination of sulfate in ethanol fuel using a FIA system. The PCME was prepared by polymerization of pyrrole at a glassy carbon electrode by means of cyclic voltammetry technique. An analytical curve from 1.0 x 10−5 to 8.0 x 10−5 mol L−1 was obtained in flow injection system based on the PCME. An amperometric sensibility of 2.3 x 10−3 A mol−1 L and a detection limit of 2.5 x 10−6 mol L−1 were achieved. The proposed method was employed for determination of sulfate ions in commercial samples of ethanol fuel. The results were in good agreement with those obtained by the ionic chromatographic method.