Natural freeze crystallization : purification of aqueous Na2SO4 solutions with cold air

The aim of this thesis was to examine efficiency of freeze crystallization and eutectic freeze crystallization in purification of wastewater by imitating natural freezing. In addition, a mathematic model based on heat transfer to determine ice thickness and ice growth rate was examined. Also, the amount of sodium sulfate crystallized at the eutectic point was under investigation. In literature part, advantages and applications of the freeze crystallization are discussed, and possibility to apply it in Northern hemisphere winter weather conditions is under study. Furthermore, main sources of sodium sulfate from Finnish industries are described. The experiments were carried out in modified chest freezer, where a fan was placed in order to obtain laminar air flow inside. Picolog PT-104 data logger was used to monitor temperature changes in the salt-water solution, and constant temperature was maintained in the crystallizer with Lauda RP 850 thermostat. The impurity of formed ice layer was determined by weighing ice samples after experiment and again after 24 hours drying to full dryness in oven. Volume of salt-water solution was also measured after experiment. The highest purity of formed ice layer was obtained with small temperature difference and with long freezing time. On the other hand, the amount of crystallized sodium sulfate was its greatest with long freezing time and higher temperature difference. The results obtained by the mathematic model and empirical results did not differ significantly in most of the experiments. However, the difference increased when salt-water mixture reached its eutectic point, leading to simultaneous ice and salt crystallization. Eutectic point was reached only with the highest salt concentration with one exception. In these cases, calculated values were in many cases greater than the experimental ones. In winter weather conditions freeze crystallization is cost-effective wastewater treatment method and rather simple. Nonetheless, the efficiency and separation rate are strongly depended on ambient temperature and its changes

Crystallization of selected anions and cations from mine waters

The aim of this Master’s thesis was to review some methods that are already being utilized in a field of mine water purification and to find and study possible new methods and chemicals for mine water purification by precipitation. The target was also to list the optimal process conditions for these precipitating chemicals. Separation methods were reviewed for several anions and cations, but being a real topical issue, sulphate removal was selected to be in the main focus. Sulphate salts e.g. Na2SO4 are relatively soluble in water, which makes the separation processes difficult. Eutectic freeze crystallization was studied more closely in laboratory tests for sodium sulphate removal. Gravimetric solubility tests were made for three cases of mixed electrolyte solutions: Na2SO4 – NaOH, BaSO4 – NaOH and Na3PO4 – NaOH. The aim of these experiments was to study the effect of NaOH addition on solubility of the studied salt. These phenomena were however noticed to be difficult to see in the used laboratory tests. Thus mathematical modelling was utilized to contribute the laboratory experiments and to bring additional information of the influence of NaOH presence on solubility of selected electrolytes, Na2SO4 and Na3PO4. The results from mathematical modelling of activity coefficients suggest Na2SO4 and Na3PO4 to be precipitated rather with presence and with higher concentrations of NaOH, since the raise of NaOH concentration decreases the solubility of these electrolytes in water.

Jätevesien puhdistus jätevesialtaissa jäädyttämällä - Kartoitus potentiaalisista sovellutuksista Suomessa

Uusia jäteveden puhdistusprosesseja kartoitetaan Suomessakin esimerkiksi kiristyvien päästömääräyksien vuoksi sekä parempia kustannus- ja energiatehokkuuksia tavoiteltaessa. Jätevesien puhdistus on Suomessa jo nykyään hyvällä tasolla, mutta muun muassa raskasmetallien, torjunta-aineiden, hormonien ja lääkeaineiden pitoisuuksien kasvut jätevesissä asettavat haasteita nykyisin käytössä oleville jäteveden puhdistusmenetelmille, sillä niitä ei ole suunniteltu näiden aineiden talteenottoon ja suurin osa aineista jää veteen. Lisäksi jätevedet halutaan nähdä enemmänkin resurssina kuin jätteenä, josta voidaan ottaa talteen hyödyllisiä komponentteja, kuten suoloja. Alueilla, joissa vuorokauden keskilämpötila pysyttelee edes osan vuodesta pakkasella, veden luonnollista jäätymisprosessia voidaan käyttää hyväksi jäteveden puhdistuksessa. Tässä työssä selvitettiin kiteytymisen teorian ja aikaisempien tutkimusten avulla, millaisten jätevesien puhdistukseen jäädytyskiteytys sopii sekä pohdittiin menetelmän potentiaalisia sovelluskohteita Suomessa. Jäädytyskiteytyksen todettiin olevan turvallinen ja energiatehokas ratkaisu monien koostumukseltaan erilaisien jätevesien puhdistukseen. Menetelmällä voitaneen puhdistaa öljyisiä, orgaanisia ja/tai epäorgaanisia epäpuhtauksia tai raskasmetalleja sisältäviä sekä myrkyllisiä jätevesiä. Olosuhteet prosessille ovat parhaat Pohjois-Suomessa, jossa vuorokauden keskilämpötila pysyttelee nollan alapuolella noin seitsemän kuukautta vuodesta. Etelä-Suomessa vastaava luku on kolme. Menetelmän potentiaalisia sovelluskohteita ovat esimerkiksi kaivosteollisuuden ja kaatopaikkojen jätevedet, joiden puhdistukseen jäädytyskiteytys saattaisi soveltua erinomaisesti. Jäädyttämällä voitaisiin myös puhdistaa tekstiili- ja nahkateollisuuden jätevesiä, sillä niiden sisältämien väriaineiden erottaminen vedestä on perinteisillä jäteveden puhdistusmenetelmillä usein vaikeaa tai jopa mahdotonta. Suolojen kiteyttämiseen vaadittavia korkeampia suolapitoisuuksia todettiin löytyvän lähinnä membraaniprosessien, kuten käänteisosmoosin, rejektivesistä. Sopivimmat eutektiset olosuhteet kiteyttämiseen ovat natriumsulfaatilla, kaliumsulfaatilla ja natriumkarbonaatilla. Veden luonnollisen jäätymisprosessin hyödyntäminen jätevedenpuhdistuksessa on huomionarvoinen idea. Prosessin käyttöönottoa haittaavat esimerkiksi korkeat investointikustannukset, mutta ne tulevat todennäköisesti ajan myötä teknologian kehittyessä laskemaan. Lisäksi monet prosessiin liittyvät käytännön asiat ovat vielä tutkimuksen alla. On myös huomattava, että Suomessakaan lämpötila ei pysyttele koko vuotta pakkasella, joten jäädytyksen rinnalla on oltava jokin toinen prosessi, jolla jätevedet puhdistetaan lämpötilan ollessa nollan yläpuolella.

How different is water crystallization from polymer crystallization under confinement?

Ziel der vorliegenden Dissertation war es, Einblicke in das Kristallisationsverhalten weicher Materie („soft matter“), wie verschiedener Polymere oder Wasser, unter räumlicher Einschränkung („confinement“) zu erlangen. Dabei sollte untersucht werden, wie, weshalb und wann die Kristallisation in nanoporösen Strukturen eintritt. Desweiteren ist Kristallisation weicher Materie in nanoporösen Strukturen nicht nur aus Aspekten der Grundlagenforschung von großem Interesse, sondern es ergeben sich zahlreiche praktische Anwendungen. Durch die gezielte Steuerung der Kristallinität von Polymeren könnten somit Materialien mit verschiendenen mechanischen und optischen Eigenschaften erhalten werden. Desweiteren wurde auch räumlich eingeschränktes Wasser untersucht. Dieses spielt eine wichtige Rolle in der Molekularbiologie, z.B. für das globuläre Protein, und als Wolkenkondensationskeime in der Atmosphärenchemie und Physik. Auch im interstellaren Raum ist eingeschränktes Wasser in Form von Eispartikeln anzutreffen. Die Kristallisation von eingeschränktem Wasser zu verstehen und zu beeinflussen ist letztlich auch für die Haltbarkeit von Baumaterialien wie etwa Zement von großem Interesse.rnUm dies zu untersuchen wird Wasser in der Regel stark abgekühlt und das Kristallisationsverhalten in Abhängigkeit des Volumens untersucht. Dabei wurde beobachtet, dass Mikro- bzw. Nanometer große Volumina erst ab -38 °C bzw. -70 °C kristallisieren. Wasser unterliegt dabei in der Regel dem Prozess der homogenen Nukleation. In der Regel gefriert Wasser aber bei höheren Temperaturen, da durch Verunreinigungen eine vorzeitige, heterogene Nukleation eintritt.rnDie vorliegende Arbeit untersucht die sachdienlichen Phasendiagramme von kristallisierbaren Polymeren und Wasser unter räumlich eingeschränkten Bedingungen. Selbst ausgerichtetes Aluminiumoxid (AAO) mit Porengrößen im Bereich von 25 bis 400 nm wurden als räumliche Einschränkung sowohl für Polymere als auch für Wasser gewählt. Die AAO Nanoporen sind zylindrisch und parallel ausgerichtet. Außerdem besitzen sie eine gleichmäßige Porenlänge und einen gleichmäßigen Durchmesser. Daher eignen sie sich als Modelsystem um Kristallisationsprozesse unter wohldefinierter räumlicher Einschränkung zu untersuchen.rnEs wurden verschiedene halbkristalline Polymere verwendet, darunter Poly(ethylenoxid), Poly(ɛ-Caprolacton) und Diblockcopolymere aus PEO-b-PCL. Der Einfluss der Porengröße auf die Nukleation wurde aus verschiedenen Gesichtspunkten untersucht: (i) Einfluss auf den Nukleationmechanismus (heterogene gegenüber homogener Nukleation), (ii) Kristallorientierung und Kristallinitätsgrad und (iii) Zusammenhang zwischen Kristallisationstemperatur bei homogener Kristallisation und Glasübergangstemperatur.rnEs konnte gezeigt werden, dass die Kristallisation von Polymeren in Bulk durch heterogene Nukleation induziert wird und das die Kristallisation in kleinen Poren hauptsächlich über homogene Nukleation mit reduzierter und einstellbarer Kristallinität verläuft und eine hohe Kristallorientierung aufweist. Durch die AAOs konnte außerdem die kritische Keimgröße für die Kristallisation der Polymere abgeschätzt werden. Schließlich wurde der Einfluss der Polydispersität, von Oligomeren und anderen Zusatzstoffen auf den Nukleationsmechanismus untersucht.rn4rnDie Nukleation von Eis wurde in den selben AAOs untersucht und ein direkter Zusammenhang zwischen dem Nukleationstyp (heterogen bzw. homogen) und der gebildeten Eisphase konnte beobachtet werden. In größeren Poren verlief die Nukleation heterogen, wohingegen sie in kleineren Poren homogen verlief. Außerdem wurde eine Phasenumwandlung des Eises beobachtet. In den größeren Poren wurde hexagonales Eis nachgewiesen und unter einer Porengröße von 35 nm trat hauptsächlich kubisches Eis auf. Nennenswerter Weise handelte es sich bei dem kubischem Eis nicht um eine metastabile sondern eine stabile Phase. Abschließend wird ein Phasendiagramm für räumlich eingeschränktes Wasser vorgeschlagen. Dieses Phasendiagramm kann für technische Anwendungen von Bedeutung sein, so z.B. für Baumaterial wie Zement. Als weiteres Beispiel könnten AAOs, die die heterogene Nukleation unterdrücken (Porendurchmesser ≤ 35 nm) als Filter für Reinstwasser zum Einsatz kommen.rnNun zur Anfangs gestellten Frage: Wie unterschiedlich sind Wasser und Polymerkristallisation voneinander unter räumlicher Einschränkung? Durch Vergleich der beiden Phasendiagramme kommen wir zu dem Schluss, dass beide nicht fundamental verschieden sind. Dies ist zunächst verwunderlich, da Wasser ein kleines Molekül ist und wesentlich kleiner als die kleinste Porengröße ist. Wasser verfügt allerdings über starke Wasserstoffbrückenbindungen und verhält sich daher wie ein Polymer. Daher auch der Name „Polywasser“.

Water sorption-induced crystallization, structural relaxations and strength analysis of relaxation times in amorphous lactose/whey protein systems

Water sorption-induced crystallization, α-relaxations and relaxation times of freeze-dried lactose/whey protein isolate (WPI) systems were studied using dynamic dewpoint isotherms (DDI) method and dielectric analysis (DEA), respectively. The fractional water sorption behavior of lactose/WPI mixtures shown at aw ≤ 0.44 and the critical aw for water sorption-related crystallization (aw(cr)) of lactose were strongly affected by protein content based on DDI data. DEA results showed that the α-relaxation temperatures of amorphous lactose at various relaxation times were affected by the presence of water and WPI. The α-relaxation-derived strength parameter (S) of amorphous lactose decreased with aw up to 0.44 aw but the presence of WPI increased S. The linear relationship for aw(cr) and S for lactose/WPI mixtures was also established with R2 > 0.98. Therefore, DDI offers another structural investigation of water sorption-related crystallization as governed by aw(cr), and S may be used to describe real time effects of structural relaxations in noncrystalline multicomponent solids.

A rational protocol for the successful crystallization of l-amino-acid oxidase from Bothrops atrox

Despite the valuable contributions of robotics and high-throughput approaches to protein crystallization, the role of an experienced crystallographer in the evaluation and rationalization of a crystallization process is still crucial to obtaining crystals suitable for X-ray diffraction measurements. In this work, the difficult task of crystallizing the flavoenzyme l-amino-acid oxidase purified from Bothrops atrox snake venom was overcome by the development of a protocol that first required the identification of a non-amorphous precipitate as a promising crystallization condition followed by the implementation of a methodology that combined crystallization in the presence of oil and seeding techniques. Crystals were obtained and a complete data set was collected to 2.3 A resolution. The crystals belonged to space group P2(1), with unit-cell parameters a = 73.64, b = 123.92, c = 105.08 A, beta = 96.03 degrees. There were four protein subunits in the asymmetric unit, which gave a Matthews coefficient V (M) of 2.12 A3 Da-1, corresponding to 42% solvent content. The structure has been solved by molecular-replacement techniques.

Expression, crystallization and preliminary crystallographic analysis of PilZ(XAC1133) from Xanthomonas axonopodis pv. citri

Proteins containing PilZ domains are widespread in Gram-negative bacteria and have recently been shown to be involved in the control of biofilm formation, adherence, aggregation, virulence-factor production and motility. Furthermore, some PilZ domains have recently been shown to bind the second messenger bis(3'-> 5') cyclic diGMP. Here, the cloning, expression, purification and crystallization of PilZ(XAC1133), a protein consisting of a single PilZ domain from Xanthomonas axonopodis pv. citri, is reported. The closest PilZ(XAC1133) homologues in Pseudomonas aeruginosa and Neisseria meningitidis control type IV pilus function. Recombinant PilZ(XAC1133) containing selenomethionine was crystallized in space group P6(1). The unit-cell parameters were a = 62.125, b = 62.125, c = 83.543 angstrom. These crystals diffracted to 1.85 angstrom resolution and a MAD data set was collected at a synchrotron source. The calculated Matthews coefficient suggested the presence of two PilZ(XAC1133) molecules in the asymmetric unit.

Crystallization and preliminary X-ray analysis of LipL32 from Leptospira interrogans serovar Copenhageni

LipL32 is a major surface protein that is expressed during infection by pathogenic Leptospira. Here, the crystallization of recombinant LipL32(21-272), which corresponds to the mature LipL32 protein minus its N-terminal lipid-anchored cysteine residue, is described. Selenomethionine-labelled LipL32(21-272) crystals diffracted to 2.25 angstrom resolution at a synchrotron source. The space group was P3(1)21 or P3(2)21 and the unit-cell parameters were a = b = 126.7, c = 96.0 angstrom.

Crystallization, data collection and data processing of maltose-binding protein (MalE) from the phytopathogen Xanthomonas axonopodis pv. citri

Maltose-binding protein is the periplasmic component of the ABC transporter responsible for the uptake of maltose/maltodextrins. The Xanthomonas axonopodis pv. citri maltose-binding protein MalE has been crystallized at 293 Kusing the hanging-drop vapour-diffusion method. The crystal belonged to the primitive hexagonal space group P6(1)22, with unit-cell parameters a = 123.59, b = 123.59, c = 304.20 angstrom, and contained two molecules in the asymetric unit. It diffracted to 2.24 angstrom resolution.

KINETICS VERSUS HYDRODYNAMICS: GENERALIZATION OF LANDAU/COOPER-FRYE PRESCRIPTION FOR FREEZE-OUT

The problem of spectra formation in hydrodynamic approach to A + A collisions is considered within the Boltzmann equations. It is shown analytically and illustrated by numerical calculations that the particle momentum spectra can be presented in the Cooper-R-ye form despite freeze-out is not sharp and has the finite temporal width. The latter is equal to the inverse of the particle collision rate at points (t(sigma) (r, p), r) of the maximal emission at a fixed momentum p. The set of these points forms the hypersurfaces t(sigma)(r,p) which strongly depend on the values of p and typically do not enclose completely the initially dense matter. This is an important difference from the standard Cooper-Frye prescription (CFp), with a common freeze-out hypersurface for all p, that affects significantly the predicted spectra. Also, the well known problem of CFp as for negative contributions to the spectra from non-space-like parts of the freeze-out hypersurface is naturally eliminated in this improved prescription.

Scaling properties at freeze-out in relativistic heavy-ion collisions

Identified charged pion, kaon, and proton spectra are used to explore the system size dependence of bulk freeze-out properties in Cu + Cu collisions at root s(NN) = 200 and 62.4 GeV. The data are studied with hydrodynamically motivated blast-wave and statistical model frameworks in order to characterize the freeze-out properties of the system. The dependence of freeze-out parameters on beam energy and collision centrality is discussed. Using the existing results from Au + Au and pp collisions, the dependence of freeze-out parameters on the system size is also explored. This multidimensional systematic study furthers our understanding of the QCD phase diagram revealing the importance of the initial geometrical overlap of the colliding ions. The analysis of Cu + Cu collisions expands the system size dependence studies from Au + Au data with detailed measurements in the smaller system. The systematic trends of the bulk freeze-out properties of charged particles is studied with respect to the total charged particle multiplicity at midrapidity, exploring the influence of initial state effects.

Fluoride-modified electrical properties of lead borate glasses and electrochemically induced crystallization in the glassy state

Lead fluoroborate glasses were prepared by the melt-quenching technique and characterized in terms of (micro)structural and electrical properties. The study was conducted on as prepared as well as temperature- and/or electric field-treated glass samples. The results show that, in the as-prepared glassy-state materials, electrical conductivity improved with increasing the PbF(2) glass content. This result involves both an increase of the fluoride charge carrier density and, especially, a decrease of the activation energy from a glass structure expansion improving charge carrier mobility. Moreover, for the electric field-treated glass samples, surface crystallization was observed even below the glass transition temperature. As previously proposed in literature, and shown here, the occurrence of this phenomenon arose from an electrochemically induced redox reaction at the electrodes, followed by crystallite nucleation. Once nucleated, growth of beta-PbF(2) crystallites, with the indication of incorporating reduced lead ions (Pb(+)), was both (micro)structurally and electrically detectable and analyzed. The overall crystallization-associated features observed here adapt well with the floppy-rigid model that has been proposed to further complete the original continuous-random-network model by Zachariasen for closely addressing not only glasses' structure but also crystallization mechanism. Finally, the crystallization-modified kinetic picture of the glasses' electrical properties, through application of polarization/depolarization measurements originally combined with impedance spectroscopy, was extensively explored. (c) 2008 American Institute of Physics.

Crystallization and preliminary X-ray diffraction analysis of a glutathione S-transferase from Xylella fastidiosa

Glutathione S-transferases (GSTs) form a group of multifunctional isoenzymes that catalyze the glutathione-dependent conjugation and reduction reactions involved in the cellular detoxification of xenobiotic and endobiotic compounds. GST from Xylella fastidiosa (xfGST) was overexpressed in Escherichia coli and purified by conventional affinity chromatography. In this study, the crystallization and preliminary X-ray analysis of xfGST is described. The purified protein was crystallized by the vapour-diffusion method, producing crystals that belonged to the triclinic space group P1. The unit-cell parameters were a = 47.73, b = 87.73, c = 90.74 angstrom, alpha = 63.45, beta = 80.66, gamma = 94.55 degrees. xfGST crystals diffracted to 2.23 angstrom resolution on a rotating-anode X-ray source.

Crystallization and preliminary structural analysis of the giant haemoglobin from Glossoscolex paulistus at 3.2 angstrom

Glossoscolex paulistus is a free-living earthworm encountered in south-east Brazil. Its oxygen transport requirements are undertaken by a giant extracellular haemoglobin, or erythrocruorin (HbGp), which has an approximate molecular mass of 3.6 MDa and, by analogy with its homologue from Lumbricus terrestris (HbLt), is believed to be composed of a total of 180 polypeptide chains. In the present work the full 3.6 MDa particle in its cyanomet state was purified and crystallized using sodium citrate or PEG8000 as precipitant. The crystals contain one-quarter of the full particle in the asymmetric unit of the I222 cell and have parameters of a = 270.8 angstrom, b = 320.3 angstrom and c = 332.4 angstrom. Diffraction data were collected to 3.15 angstrom using synchrotron radiation on beamline X29A at the Brookhaven National Laboratory and represent the highest resolution data described to date for similar erythrocruorins. The structure was solved by molecular replacement using a search model corresponding to one-twelfth of its homologue from HbLt. This revealed that HbGp belongs to the type I class of erythrocruorins and provided an interpretable initial electron density map in which many features including the haem groups and disulfide bonds could be identified.

Purification, crystallization and preliminary crystallographic analysis of the catalytic domain of the extracellular cellulase CBHI from Trichoderma harzianum

The filamentous fungus Trichoderma harzianum has a considerable cellulolytic activity that is mediated by a complex of enzymes which are essential for the hydrolysis of microcrystalline cellulose. These enzymes were produced by the induction of T. harzianum with microcrystalline cellulose (Avicel) under submerged fermentation in a bioreactor. The catalytic core domain (CCD) of cellobiohydrolase I (CBHI) was purified from the extracellular extracts and submitted to robotic crystallization. Diffraction-quality CBHI CCD crystals were grown and an X-ray diffraction data set was collected under cryogenic conditions using a synchrotron-radiation source.