Statistical investigation on morphology development of gallium nitride in initial growth stage

Morphology of Gallium Nitride (GaN) in initial growth stage was observed with atomic force microscopy (AFM) and scanning electron microscopy (SEM), It was found that the epilayer developed from islands to coalesced film. Statistics based on AFM observation was carried out to investigate the morphology characteristics. It was found that the evolution of height distribution could be used to describe morphology development. Statistics also clearly revealed variation of top-face growth rate among islands. Indium-doping effect on morphology development was also statistically studied. The roughening and smoothing behavior in morphology development was explained. (C) 2002 Elsevier Science B.V. All rights reserved.

Effects of forced solution flow on lysozyme crystal growth

In order to study quantitatively the effects of forced solution on crystal growth, we designed a new set of experimental equipment, in particular, a microchannel mixer was used as crystallization container so that the consumption of protein samples was much reduced and thus an exact syringe pump could be used for precise control of the flow rates. Since the mixer’s section was designed to be rectangular, the solution velocity in its center was steady and constant, and thus repeatable experiments were facilitated. Experimental results showed that the effects of forced solution on protein crystal growth were different under different levels of supersaturation, and new results were obtained for cases of high supersaturation. When the supersaturation is σ = 2.3, with increasing flow rates the growth rates of the lysozyme crystal’s (110) face hardly change when the flow rates are lower than 1300 μm/s, and decrease quickly afterwards. When the flow rate reaches 2000 μm/s, the crystal nearly ceases to grow. When the supersaturation is σ = 2.7, with increasing flow rates the (110) face growth rates increase at the beginning then reach the maximum values at 1700 μm/s – 1900 μm/s and decrease afterwards, approaching zero or so when the flow rate reaches 12000 μm/s. The higher the supersaturation, the larger the flow rate at which the crystal ceases to grow. © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Verification of McCabe's Delta L Law for Growth of Lysozyme Crystals by Hanging Drop Method

Lysozyme is a naturally occurring enzyme in egg white and has high commercial importance due to its antimicrobial properties. The main objective of this work was to study the growth rate of lysozyme crystals isolated from egg for the first 72 hours and verify the results with McCabe’s constant crystal growth theory. Hanging drop crystallization method was used to form high purity lysozyme crystals from the embryonic stage. To this end, this work differs from an earlier work of Forsythe et al., who used seed crystals in the size range of 10 µm - 40 µm for face growth measurements at different pH values. The maximum crystal size recorded in the present work was 392.86 µm, which is within the typical size range of 50 µm - 500 µm for which constant crystal growth is expected to hold according to McCabe’s ?L law. Electron micrographs (SEM) revealed the structure and dimensions of the crystals while SDS-Page was used to measure the purity of the crystals. The SEM results showed that that lysozyme growth rate was linear and agreed with McCabe’s constant growth theory, producing a growth rate of 1.77 x 10-3 µm .s-1

Orthognathic Surgery in the Young Cleft Patient: Preliminary Study on Subsequent Facial Growth

Purpose: This study evaluated the long-term effects of orthognathic surgery on subsequent growth of the maxillomandibular complex in the young cleft patient. Patients and Methods: We evaluated 12 young cleft patients (9 male and 3 female patients), with a mean age of 12 years 6 months (range, 9 years 8 months to 15 years 4 months), who underwent Le Fort I osteotomies, with maxillary advancement, expansion, and/or downgrafting, by use of autogenous bone or hydroxyapatite grafts, when indicated, for maxillary stabilization. Five patients had concomitant osteotomies of the mandibular ramus. All patients had presurgical and postsurgical orthodontic treatment to control the occlusion. Radiographs taken at initial evaluation (T1) and presurgery (T2) were compared to establish the facial growth vector before surgery, whereas radiographs taken immediately postsurgery (T3) and at longest follow-up (T4) were used to determine postsurgical growth. Each patient's lateral cephalograms were traced, and 16 landmarks were identified and used to compute 11 measurements describing presurgical and postsurgical growth. Results: Before surgery, all patients had relatively normal growth. After surgery, cephalograms showed statistically significant growth changes from T3 to T4, with the maxillary depth decreasing by -3.3° ± 1.8°, Sella-nasion-point A by -3.3° ± 1.8°, and point A-nasion-point B by -3.6° ± 2.8°. The angulation of the maxillary incisors increased by 9.2° ± 11.7°. Of 12 patients, 11 showed disproportionate postsurgical jaw growth. Maxillary growth occurred predominantly in a vertical vector with no anteroposterior growth, even though most patients had shown anteroposterior growth before surgery. The distance increased in the linear measurement from nasion to gnathion by 10.3 ± 7.9 mm. Four of 5 patients operated on during the mixed dentition phase had teeth that erupted through the cleft area. A variable impairment of postoperative growth was seen with the 2 types of grafting material used. No significant difference was noted in the effect on growth in patients with unilateral clefts versus those with bilateral clefts. The presence of a pharyngeal flap was noted to adversely affect growth, whereas simultaneous mandibular surgery did not. After surgery, 11 of 12 patients tended toward a Class III end-on occlusal relation. Conclusions: Orthognathic surgery may be performed on growing cleft patients when mandated by psychological and/or functional concerns. The surgeon must be cognizant of the adverse postsurgical growth outcomes when performing orthognathic surgery on growing cleft patients with the possibility for further surgery requirements. Performing maxillary osteotomies on cleft patients would be more predictable after completion of facial growth. © 2008 American Association of Oral and Maxillofacial Surgeons.

Polarization effects simulation of AlGaN/GaN heterojunction by using a symbolistic delta-doping layer

Polarization effects in AlGaN/GaN heterojunction are simulated based on a traditional semiconductor device simulator. A delta doping layer is purposely inserted at the interface of the heterojunction in the simulation, so the ionized donors or acceptors can represent polarization-induced positive or negative fixed charges. The free electron distribution of single AlGaN/GaN heterostructures with Ga-face and N-face growth is compared, and the results of the simulation show that carrier confinement takes place only in the former structure. The dependence of sheet density of free electrons at the interface of Ga-face growth AlGaN/GaN on Al composition and the thickness of AlGaN is also investigated. The consistency of simulation results with the experiments and calculations reported by other researchers shows that this method can be effectively used to deal with the polarization effects in the simulation of GaN-based heterojunction devices. (C) 2004 Elsevier Ltd. All rights reserved.

The role of bond covenants and short-term debt: evidence from Brazil

Esta dissertação tem como objetivo analisar a relação entre covenants e alavancagem financeira no curto e longo prazo com oportunidades de crescimento. A partir de uma amostra de 159 debêntures, encontramos evidência de que: 1) Covenants e dívida de curto-prazo podem ser considerados substitutos na atenuação do conflito de agência, uma vez que apresentaram relação negativa e significante e; 2) A relação negativa existente entre dívida de curto prazo e oportunidades de crescimento pode ser reduzida através da utilização de covenants.

Changes in facial morphology after adenotonsillectomy in mouth-breathing children

Background. Morphological and dentofacial alterations have been attributed to impaired respiratory function. Objective. To examine the influence of mouth breathing (MB) on children facial morphology before and after adenoidectomy or adenotonsillectomy. Methods. Thirty-three MB children who restored nasal breathing (NB) after surgery and 22 NB children were evaluated. Both groups were submitted to lateral cephalometry, at time 1 (T1) before and at time 2 (T2) 28months on average postoperatively. Results. Comparison between the MB and NB groups at T1 showed that mouth breathers had higher inclination of the mandibular plane; more obtuse gonial angle; dolichofacial morphology; and a decrease in the total and inferior posterior facial heights. Twenty-eight months after the MB surgical intervention, they still presented a dolichofacial morphologic pattern. During this period, MB altered the face growth direction and decreased their mandible plane inclination, with reduction in the SN.GoGn, PP.MP, SNGn, and ArGo.GoMe parameters as well as an increase in BaN.PtGn. Conclusion. After the MB rehabilitation, children between 3 and 6years old presented significant normalization in the mandibular growth direction, a decrease in the mandible inclination, and an increase in the posterior facial height. Instead, they still persisted with a dolichofacial pattern when compared with nasal breathers. © 2011 The Authors. International Journal of Paediatric Dentistry © 2011 BSPD, IAPD and Blackwell Publishing Ltd.

Estudo da proporção áurea em indivíduos braqui e mesofaciais por meio de radiografias cefalométricas laterais

Pós-graduação em Biopatologia Bucal - ICT

Homoepitaxial growth and device characteristics of SiC on Si-face (0001) 6H-SiC

Homoepitaxial growth of SiC on a Si-face (0 0 0 1) GH-SIC substrate has been performed in a modified gas-source molecular beam epitaxy system with Si2H6 and C2H4 at temperatures ranging 1000 1450 degreesC while keeping a constant SiC ratio (0.7) in the gas phase. X-ray diffraction patterns, Raman scattering measurements. and low-temperature photoluminescence spectra showed single-crystalline SiC. Mesa-type SiC p-n junctions were obtained on these epitaxial layers, and their I-V characteristics are presented. (C) 2001 Elsevier Science B.V. All rights reserved.

Homoepitaxial growth and device characteristics of SiC on Si-face (0001) 6H-SiC

Homoepitaxial growth of SiC on a Si-face (0 0 0 1) GH-SIC substrate has been performed in a modified gas-source molecular beam epitaxy system with Si2H6 and C2H4 at temperatures ranging 1000 1450 degreesC while keeping a constant SiC ratio (0.7) in the gas phase. X-ray diffraction patterns, Raman scattering measurements. and low-temperature photoluminescence spectra showed single-crystalline SiC. Mesa-type SiC p-n junctions were obtained on these epitaxial layers, and their I-V characteristics are presented. (C) 2001 Elsevier Science B.V. All rights reserved.

Modulation of dermal microvascular endithelial cell responses to growth factors and haemostatic factors in the presence of vitronectin

In order to effect permanent closure in burns patients suffering from full thickness wounds, replacing their skin via split thickness autografting, is essential. Dermal substitutes in conjunction with widely meshed split thickness autografts (+/- cultured keratinocytes) reduce scarring at the donor and recipient sites of burns patients by reducing demand for autologous skin (both surface area and thickness), without compromising dermal delivery at the wound face. Tissue engineered products such as Integra consist of a dermal template which is rapidly remodelled to form a neodermis, at which time the temporary silicone outer layer is removed and replaced with autologous split thickness skin. Whilst provision of a thick tissue engineered dermis at full thickness burn sites reduces scarring, it is hampered by delays in vascularisation which results in clinical failure. The ultimate success of any skin graft product is dependent upon a number of basic factors including adherence, haemostasis and in the case of viable tissue grafts, success is ultimately dependent upon restoration of a normal blood supply, and hence this study. Ultimately, the goal of this research is to improve the therapeutic properties of tissue replacements, through impregnation with growth factors aimed at stimulating migration and proliferation of microvascular endothelial cells into the donor tissue post grafting. For the purpose of my masters, the aim was to evaluate the responsiveness of a dermal microvascular endothelial cell line to growth factors and haemostatic factors, in the presence of the glycoprotein vitronectin. Vitronectin formed the backbone for my hypothesis and research due to its association with both epithelial and, more specifically, endothelial migration and proliferation. Early work using a platform technology referred to as VitroGro (Tissue Therapies Ltd), which is comprised of vitronectin bound BP5/IGF-1, aided keratinocyte proliferation. I hypothesised that this result would translate to another epithelium - endothelium. VitroGro had no effect on endothelial proliferation or migration. Vitronectin increases the presence of Fibroblast Growth Factor (FGF) and Vascular Endothelial Growth Factor (VEGF) receptors, enhancing cell responsiveness to their respective ligands. So, although Human Microvascular Endothelial Cell line 1 (HMEC-1) VEGF receptor expression is generally low, it was hypothesised that exposure to vitronectin would up-regulate this receptor. HMEC-1 migration, but not proliferation, was enhanced by vitronectin bound VEGF, as well as vitronectin bound Epidermal Growth Factor (EGF), both of which could be used to stimulate microvascular endothelial cell migration for the purpose of transplantation. In addition to vitronectin's synergy with various growth factors, it has also been shown to play a role in haemostasis. Vitronectin binds thrombin-antithrombin III (TAT) to form a trimeric complex that takes on many of the attributes of vitronectin, such as heparin affinity, which results in its adherence to endothelium via heparan sulfate proteoglycans (HSP), followed by unaltered transcytosis through the endothelium, and ultimately its removal from the circulation. This has been documented as a mechanism designed to remove thrombin from the circulation. Equally, it could be argued that it is a mechanism for delivering vitronectin to the matrix. My results show that matrix-bound vitronectin dramatically alters the effect that conformationally altered antithrombin three (cATIII) has on proliferation of microvascular endothelial cells. cATIII stimulates HMEC-1 proliferation in the presence of matrix-bound vitronectin, as opposed to inhibiting proliferation in its absence. Binding vitronectin to tissues and organs prior to transplant, in the presence of cATIII, will have a profound effect on microvascular infiltration of the graft, by preventing occlusion of existing vessels whilst stimulating migration and proliferation of endothelium within the tissue.

Innovative and entrepreneurial activity in the public sector : the changing face of public sector institutions

This paper investigates the elements which support innovative and entrepreneurial activity in New Zealand’s state owned enterprises (SOEs). An inductive case study design, involving interview data, textual analysis, and observation, was applied to three SOEs. Findings reveal that those aspects typically associated with entrepreneurship, such as innovation, risk acceptance, pro-activeness and growth, are often supported by a number of unexpected elements within the public sector. These elements include culture, branding, operational excellence, cost efficiency, and knowledge transfer. The implications are twofold. First, that innovative and entrepreneurial activity in the public sector can go beyond policy-making, with SOEs representing an important policy decision and sector of the New Zealand Government. And second, that the impact of several SOEs on international markets suggests competition on the global stage will increasingly come from both public and private sector organizations.

Professional growth through working together : a study of reciprocal benefits for teacher and education advisor through classroom based professional development

Teacher professional development provided by education advisors as one-off, centrally offered sessions does not always result in change in teacher knowledge, beliefs, attitudes or practice in the classroom. As the mathematics education advisor in this study, I set out to investigate a particular method of professional development so as to influence change in a practising classroom teacher’s knowledge and practices. The particular method of professional development utilised in this study was based on several principles of effective teacher professional development and saw me working regularly in a classroom with the classroom teacher as well as providing ongoing support for her for a full school year. The intention was to document the effects of this particular method of professional development in terms of the classroom teacher’s and my professional growth to provide insights for others working as education advisors. The professional development for the classroom teacher consisted of two components. The first was the co-operative development and implementation of a mental computation instructional program for the Year 3 class. The second component was the provision of ongoing support for the classroom teacher by the education advisor. The design of the professional development and the mental computation instructional program were progressively refined throughout the year. The education advisor fulfilled multiple roles in the study as teacher in the classroom, teacher educator working with the classroom teacher and researcher. Examples of the professional growth of the classroom teacher and the education advisor which occurred as sequences of changes (growth networks, Hollingsworth, 1999) in the domains of the professional world of the classroom teacher and education advisor were drawn from the large body of data collected through regular face-to-face and email communications between the classroom teacher and the education advisor as well as from transcripts of a structured interview. The Interconnected Model of Professional Growth (Clarke & Hollingsworth, 2002; Hollingsworth, 1999) was used to summarise and represent each example of the classroom teacher’s professional growth. A modified version of this model was used to summarise and represent the professional growth of the education advisor. This study confirmed that the method of professional development utilised could lead to significant teacher professional growth related directly to her work in the classroom. Using the Interconnected Model of Professional Growth to summarise and represent the classroom teacher’s professional growth and the modified version for my professional growth assisted with the recognition of examples of how we both changed. This model has potential to be used more widely by education advisors when preparing, implementing, evaluating and following-up on planned teacher professional development activities. The mental computation instructional program developed and trialled in the study was shown to be a successful way of sequencing and managing the teaching of mental computation strategies and related number sense understandings to Year 3 students. This study was conducted in one classroom, with one teacher in one school. The strength of this study was the depth of teacher support provided made possible by the particular method of the professional development, and the depth of analysis of the process. In another school, or with another teacher, this might not have been as successful. While I set out to change my practice as an education advisor I did not expect the depth of learning I experienced in terms of my knowledge, beliefs, attitudes and practices as an educator of teachers. This study has changed the way in which I plan to work as an education advisor in the future.

The role of transport infrastructure in facilitating the survival and growth of micro-enterprises in developing economies

Transport and logistics are essential to effective business. Very little is currently known about the impact of improved transport on micro-enterprises in developing economies and whether improvements in this area would assist the very poor. This paper looks at the obstacles of an inefficient transport facilitation system and the high costs incurred by 22 survival micro-entrepreneurs funded by the same local NGO and operating in diverse industry sectors in a peri-urban context in Mozambique. Six case studies are selected to illustrate the most common constraints they face. The perspectives of the micro-business owners are confronted with those of government officials and community leaders for two reasons: to identify any mismatch and to discuss possible solutions. Significant discrepancies are detected between government agenda and needs of the population, while community-based entrepreneurship (CBE) is discussed as a possible collective strategy in dealing with the problem.