Evaluation of various pre-treatments for the dehydration of banana and selection of suitable drying models

The thin-layer drying behaviour of bananas in a beat pump dehumidifier dryer was examined. Four pre-treatments (blanching, chilling, freezing and combined blanching and freezing) were applied to the bananas, which were dried at 50 degreesC with an air velocity of 3.1 m s(-1) and with the relative humidity of the inlet air of 10-35%. Three drying models, the simple model, the two-term exponential model and the Page model were examined. All models were evaluated using three statistical measures, correlation coefficient, root means square error, and mean absolute percent error. Moisture diffusivity was calculated based on the diffusion equation for an infinite cylindrical shape using the slope method. The rate of drying was higher for the pre-treatments involving freezing. The sample which was blanched only did not show any improvement in drying rate. In fact, a longer drying time resulted due to water absorption during blanching. There was no change in the rate for the chilled sample compared with the control. While all models closely fitted the drying data, the simple model showed greatest deviation from the experimental results. The two-term exponential model was found to be the best model for describing the drying curves of bananas because its parameters represent better the physical characteristics of the drying process. Moisture diffusivities of bananas were in the range 4.3-13.2 x 10(-10) m(2)s(-1). (C) 2002 Published by Elsevier Science Ltd.

Influence of shapes of selected vegetable materials on drying kinetics during fluidized bed drying

Three different particular geometrical shapes of parallelepiped, cylinder and sphere were taken from cut green beans (length:diameter = 1:1, 2:1 and 3:1) and potatoes (aspect ratio = 1:1, 2:1 and 3:1) and peas, respectively. Their drying behaviour in a fluidised bed was studied at three different drying temperatures of 30, 40 and 50 degreesC (RH = 15%). Drying curves were constructed using non-dimensional moisture ratio (MR) and time and their behaviour was modelled using exponential (MR = exp(-kt)) and Page (MR = exp(-kt(n))) models. The effective diffusion coefficient of moisture transfer was determined by Fickian method using uni- and three-dimensional moisture movements. The diffusion coefficient was least affected by the size when the moisture movement was considered three-dimensional, whereas the drying temperature had a significative effect on diffusivity as expected. The drying constant and diffusivity coefficients were on the descending order for potato, beans and peas. The Arrhenius activation energy for the peas was also highest, indicating a strong barrier to moisture movement in peas as compared to beans and skinless cut potato pieces. (C) 2003 Elsevier Science Ltd. All rights reserved.

Drying rates of Rubi grapes submitted to chemical pretreatments for raisin production

The objective of this work was to determine the most appropriated chemical treatment to be used to dry grapes cv. Rubi for raisin production. Drying curves for convective drying with air at 50ºC, in a tray drier, were obtained for grapes submitted to chemical pretreatments with different concentrations of potassium carbonate and olive oil, and different dipping times, according to factorial designs. Convective drying curves were also obtained for grapes pretreated in aqueous suspensions of soybean lecithin, at varied lecithin concentrations and dipping times. Page model was adjusted to the experimental drying curves, and the calculated drying times showed that the best pretreatment consisted in dipping grapes for 2 minutes in a 5% olive oil and 6% K2CO3 emulsion, at 50ºC, which resulted in a drying time close to that of the pretreatment with 2.5% of olive oil, but with a lower consumption of this substance. In addition, the immersion of grapes in an aqueous suspension of 2% soy lecithin, at 50ºC, for 5 minutes, resulted in a total drying time slightly higher than the most effective pretreatment.

Application of simulated annealing in simulation and optimization of drying process of Zea mays malt

Kinetic simulation and drying process optimization of corn malt by Simulated Annealing (SA) for estimation of temperature and time parameters in order to preserve maximum amylase activity in the obtained product are presented here. Germinated corn seeds were dried at 54-76 °C in a convective dryer, with occasional measurement of moisture content and enzymatic activity. The experimental data obtained were submitted to modeling. Simulation and optimization of the drying process were made by using the SA method, a randomized improvement algorithm, analogous to the simulated annealing process. Results showed that seeds were best dried between 3h and 5h. Among the models used in this work, the kinetic model of water diffusion into corn seeds showed the best fitting. Drying temperature and time showed a square influence on the enzymatic activity. Optimization through SA showed the best condition at 54 ºC and between 5.6h and 6.4h of drying. Values of specific activity in the corn malt were found between 5.26±0.06 SKB/mg and 15.69±0,10% of remaining moisture.

Drying rates of Rubi grapes submitted to chemical pretreatments for raisin production

O objetivo deste trabalho foi selecionar o pré-tratamento químico mais apropriado para a secagem de uvas cv. Rubi para a produção de passas. Foram obtidas curvas de secagem convectiva com ar a 50ºC, em um secador de bandejas, para uvas submetidas a pré-tratamentos químicos com diferentes concentrações de carbonato de potássio e azeite de oliva, e diferentes tempos de imersão, de acordo com planejamentos fatoriais. Também foram obtidas curvas de secagem convectiva, para uvas pré-tratadas em suspensões aquosas de lecitina de soja, em várias concentrações de lecitina e diferentes tempos de imersão. O modelo de Page foi ajustado às curvas de secagem experimental, e os tempos de secagem calculados mostraram que o melhor pré-tratamento consistiu na imersão das uvas por 2 minutos, em uma emulsão de 5% de azeite de oliva e 6% de K2CO3, a 50ºC, o que resultou em tempos de secagem próximos aos do pré-tratamento com 2,5% de azeite de oliva, mas com um menor consumo dessa substância. Além disso, a imersão das uvas em uma suspensão aquosa de 2% de lecitina de soja, a 50ºC, por 5 minutos, resultou em um tempo de secagem total apenas levemente superior ao do pré-tratamento mais efetivo.

Air-drying of fresh and osmotically pre-treated pineapple slices: Fixed air temperature versus fixed slice temperature drying kinetics

In this investigation, the air drying characteristics of fresh and osmotically pre-treated pineapple slices in a tray dryer were studied under different operating conditions. The air velocity varied from 1.5 to 2.5 m/s and the air temperature from 40 to 70 degreesC. The analytical solution of the second Fick's law for an infinite slab was used to calculate effective diffusion coefficients and their temperature dependence could be well represented by an Arrhenius-type equation. Comparison of the results showed that the diffusion coefficients were lower for the pre-treated fruit. By means of automatic control, it was possible to obtain drying curves under conditions of constant product temperature, which showed to be an alternative to reduce the drying time of pineapple slices.

The drying of sewage sludge by immersion frying

The objective of this work was to dry sewage sludge using a fry-drying process. The frying experiments were carried out in commercial fryers modified by adding thermocouples to the setup. During frying, typical drying curves were obtained and it was verified that, in relation to the parameters: oil temperature, oil type and shape of the sample, the shape factor the most effect on the drying rate, at least within the range chosen for the variables studied. Oil uptake and calorific value were also analyzed. The calorific value of the samples increased with frying time, reaching values around 24MJ/kg after 600s of frying (comparable to biocombustibles such as wood and sugarcane bagasse). The process of immersion frying showed great potential for drying materials, especially sewage sludge, obtaining a product with a high energy content, thereby increasing its value as a combustible.

Drying kinetic analysis of municipal solid waste using modified page model and pattern search method

This work studied the drying kinetics of the organic fractions of municipal solid waste (MSW) samples with different initial moisture contents and presented a new method for determination of drying kinetic parameters. A series of drying experiments at different temperatures were performed by using a thermogravimetric technique. Based on the modified Page drying model and the general pattern search method, a new drying kinetic method was developed using multiple isothermal drying curves simultaneously. The new method fitted the experimental data more accurately than the traditional method. Drying kinetic behaviors under extrapolated conditions were also predicted and validated. The new method indicated that the drying activation energies for the samples with initial moisture contents of 31.1 and 17.2 % on wet basis were 25.97 and 24.73 kJ mol−1. These results are useful for drying process simulation and industrial dryer design. This new method can be also applied to determine the drying parameters of other materials with high reliability.

Dehydration of "dedo de moça" pepper: kinetics and phytochemical concentration

Red pepper is rich in vitamin C and other phytochemicals and can be consumed as a dehydrated product. The evaluation of the best drying conditions can ensure a better quality product. This study aimed to investigate the effect of air temperature (55, 65, and 75 ºC) on drying kinetics of red peppers and on vitamin C, total phenolic content, and color of dried pepper as compared to the fresh product. Dehydration was carried out in a forced convection oven. Drying kinetics was determined by periodic weighting until constant weight. The moisture content of the fresh pepper was approximately 86%. The drying curves were fitted to three different models available in the literature. The Page model showed the best fit for this process. Analysis of variance revealed that the air drying temperature significantly influenced (p < 0.05) the quality parameters (vitamin C content, total phenolic content, and color) of the dried pepper as compared to the fresh pepper. After drying, the vitamin C retention increased with reduced air-drying temperature. In general, products dried at lower temperatures exhibited better quality due to reduced losses of bioactive compounds.

Seed quality parameters of three interspecific hybrids of elephant grass x pearl millet

An interspecific hybrid resulting from the crossing of elephant grass (Pennisetum purpureum Schumach) x pearl millet (Pennisetum glaucum (L.) R. Brown) has been developed. This hybrid, however, revealed low phenotypic uniformity and low production of pure seeds. Through recurrent selection, two improved populations were obtained (genotypes Corte and Pastoreio). The aim of this study was assessing seed quality of the three hybrids (genotypes Corte, Pastoreio and Paraiso) by tests of: seed purity; seed germination; accelerated aging test, at 42 ºC; 1,000 seeds weight; drying curves; and sorption and desorption isotherms. Recurrent selection altered the seed size and increased initial quality of population for genotype Pastoreio. Drying curves for the three hybrids have shown similar behavior and reached moisture contents of 2.1%, 1.9%, and 1.8%, respectively, after 63 days. The accelerated aging test showed that hybrid Pastoreio was the most vigorous.

Desidratação de polpas de frutas pelo método foam-mat

This study aimed to investigate the foam mat drying process of pineapple and mango pulp, as well as to evaluate the final product quality. Initially, the selection of fruit and additives was conducted based on density and stability determinations of mango, seriguela, umbu and pineapple foams. After selecting pineapple and mango for further studies, the fruit pulps and fruit foams were characterized in regard to their physicochemical composition. The temperature (60oC or 70oC) and the foam thickness (4 and 11 mm) were evaluated in accordance to the obtained drying curves and after model adjustment. Mango and pineapple powders obtained at the best process conditions were characterized in regard to their physicochemical composition, solubility, reconstitution time. Yoghurts were prepared with the addition of pineapple and mango powders and they were evaluated for their sensory acceptance. Results show that the best drying rates were achieved by using 70o C and layers 4mm thick for both fruits. The Page model successfully fitted the drying experimental data and it can be used as a predictive model. Pineapple and mango powders showed acid pH, high soluble solids content, low water activity (approx. 0.25), lipids between 1.46% and 2.03%, protein around 2.00%, and ascorbic acid content of 17,73 mg/100g and 14.32 mg/100g, for mango and pineapple, respectively. It was observed higher ascorbic acid retention for pineapple and mango powders processed at 70o C, which would be explained by the lower drying time applied. The fruit powders exhibited high solubility and fast reconstitution in water. The sensory acceptance indexes for yoghurts with the addition of both fruit powders were higher than 70%, which reflect the satisfactory product acceptance

Sistema de secagem solar para frutos tropicais e modelagem da secagem de banana em um secador de coluna estática

In this study were projected, built and tested an electric solar dryer consisting of a solar collector, a drying chamber, an exhaust fan and a fan to promote forced hot air convection. Banana drying experiments were also carried out in a static column dryer to model the drying and to obtain parameters that can be used as a first approximation in the modeling of an electric solar dryer, depending on the similarity of the experimental conditions between the two drying systems. From the banana drying experiments conducted in the static column dryer, we obtained food weight data as a function of aqueous concentration and temperature. Simplified mathematical models of the banana drying were made, based on Fick s and Fourier s second equations, which were tested with the experimental data. We determined and/or modeled parameters such as banana moisture content, density, thin layer drying curves, equilibrium moisture content, molecular diffusivity of the water in banana DAB, external mass transfer coefficient kM, specific heat Cp, thermal conductivity k, latent heat of water evaporation in the food Lfood, time to heat food, and minimum energy and power required to heat the food and evaporate the water. When we considered the shrinkage of radius R of a banana, the calculated values of DAB and kM generally better represent the phenomenon of water diffusion in a solid. The latent heat of water evaporation in the food Lfood calculated by modeling is higher than the latent heat of pure water evaporation Lwater. The values calculated for DAB and KM that best represent the drying were obtained with the analytical model of the present paper. These values had good agreement with those assessed with a numeric model described in the literature, in which convective boundary condition and food shrinkage are considered. Using parameters such as Cp, DAB, k, kM and Lfood, one can elaborate the preliminary dryer project and calculate the economy using only solar energy rather than using solar energy along with electrical energy

Estudo da secagem do pedúnculo do caju em sistemas convencional e solar: modelagem e simulação do processo

This work aims to study the drying of cashew-nut pulp with different lay-out of dryers using conventional and solar energy. It concerns with the use of exceeding of the regional raw material and the suitable knowledge for the applicability of the drying systems as pathway for food conservation. Besides, it used renewable sources as solar energy to dry these agroindustrial products. Runs were carried out using a conventional tray-dryer with temperature, air velocity control and cashew slice thickness of 55°C, 65°C, 75°C; 3.0; 4.5, 6.0 m s-1; 1.0; 1.5 and 2.0 cm, respectively, in order to compare the studied systems. To evaluate the conventional tray-dryer, it was used a diffusional model of 2nd Fick´s law, where the drying curves were quite well fitted to an infinite flat plate design. For the drying runs where the room temperature had no control, it was developed a phenomenological-mathematical model for the solar dryer with indirect radiation under natural and forced convection based on material and energy balances of the system. Besides, it was carried out assays in the in natura as well as dehydrated, statistic analysis of the experimental drying data, sensorial analysis of the final dry product and a simplified economical analysis of the systems studied

Influence of osmotic dehydration on ascorbic acid loss in pickled dry peppers (Capsicum chinense)

The objective of this work was (1) to develop a dehydrated pepper with 45% humidity, determining the drying curves for pepper, with and without osmotic pre-treatment and (2) to evaluate the influence of both drying and osmotic treatment on the content ascorbic acid (vitamin C) in fresh pepper and pepper with 45% humidity. The experiments were carried out using the peppers cut in half, with and without osmotic pre-treatment, followed by drying in an oven at 70 ºC. The results showed that the osmotic pretreatment did not influence the retention of ascorbic acid during the drying of pepper. The sensory analysis regarding the color, flavor, and texture attributes revealed that there was no difference in the acceptability.

Dehydration of dedo de moça pepper: kinetics and phytochemical concentration

A pimenta vermelha é rica em vitamina C e outros fitoquímicos e pode ser consumida como produto desidratado. A avaliação das melhores condições de secagem pode garantir melhor qualidade do produto. Assim, o objetivo deste trabalho foi estudar o efeito da temperatura do ar de secagem (55, 65, 75 ºC) sobre a cinética de secagem, conteúdos de vitamina C e fenólicos totais e cor do produto desidratado, comparando-os à pimenta in natura. A desidratação foi feita por convecção forçada em estufa. A cinética de secagem foi determinada por pesagens periódicas até peso constante. A umidade da pimenta in natura foi de aproximadamente 86%. As curvas de secagem foram ajustadas por três modelos diferentes, avaliados na literatura. O modelo de Page apresentou o melhor ajuste para este processo. A análise de variância mostrou que a temperatura de secagem influenciou significativamente (p < 0,05) os parâmetros de qualidade (conteúdo de vitamina C, conteúdo de fenólicos totais, cor) da pimenta desidratada quando comparados aos da pimenta in natura. Após a secagem, a retenção de vitamina C aumentou com a redução da temperatura de secagem. de maneira geral, a qualidade do produto foi favorecida na secagem com menor temperatura, devido à redução nas perdas de compostos bioativos.