Reduced divergence angle of photonic crystal vertical-cavity surface-emitting laser

The reduced divergence angle of the photonic crystal vertical-cavity surface-emitting laser (PC-VCSEL) was investigated in both theory and experiment. The photonic crystal waveguide possessed the weakly guiding waveguide characteristic, which accounted for the reduction of the divergence angle. The three-dimensional finite-difference time-domain method was used to simulate the designed PC-VCSEL, and a calculated divergence angle of 5.2 degrees was obtained. The measured divergence angles of our fabricated PC-VCSEL were between 5.1 degrees and 5.5 degrees over the entire drive current range, consistent with the numerical results. This is the lowest divergence angle of the fabricated PC-VCSEL ever reported.

A Single Mode 980nm InGaAs/GaAs/AlGaAs Large Optical Cavity Quantum Well Laser with Low Vertical Divergence Angle

To achieve high optical power as well as low vertical divergence angle, a new kind of optimized large optical cavity (LOC) structure is applied to a ridge waveguide 980nm InGaAs/GaAs/AlGaAs multi-quantum well laser. The optical power density in the waveguide is successfully reduced. The maximum output power is more than 400mW with a slope efficiency of 0.89W/A and the far-field vertical divergence angle is lowered to 23°.

High efficiency, low vertical divergence angle 980nnn Al-free active region lasers with novel large optical cavity and asymmetrical cladding layers

980nm InGaAs/InGaAsP/AlGaAs strained quantum well lasers,vitta novel large optical cavity and asymmetrical claddings was fabricated bg MOCVD. Very high differential quantum efficiency elf 90% (1.15W/A) and low vertical divergence angle of 24 degrees at long cavity length were obtained for 100 mu m stripe lasers. The differential quantum efficiency is up to 94% (1.20) at cavity length of 500 mu m.

Single-mode holey vertical-cavity surface-emitting laser with ultra-narrow beam divergence

We demonstrated oxide-confined 850-nm vertical-cavity surface-emitting lasers (VCSELs) with a two-dimensional petal-shaped holey structure composed of several annular-sector-shaped holes. Four types of devices with different hole numbers were designed and fabricated. The measured results showed that the larger hole number was beneficial to purifying the lasing mode, and realizing the single-mode operation. The side mode suppression ratio (SMSR) exceeded 30 dB throughout the entire drive current. Mode selective loss mechanism was used to explain the single-mode characteristic. The single-mode devices possessed good beam profiles, and the lowest divergence angle was as narrow as 3.2 degrees (full width at half maximum), attributed to the graded index profile and the shallow etching in the top distributed Bragg reflector (DBR).

Small-divergence singlemode emitting tapered distributed-feedback quantum cascade lasers

A tapered distributed feedback quantum cascade laser emitting at lambda similar to 8.1 mu m is reported. Utilising a tapered waveguide structure with a surface metal grating, the device exhibited singlemode operation over the temperature range of 100 to 214 K, with sidemode suppression ratio > 20 dB and a nearly diffraction limited far-field beam divergence angle of 5.4 degrees.

Control of filamentation induced by femtosecond laser pulses propagating in air

Filamentation formed by self-focusing of intense laser pulses propagating in air is investigated. It is found that the position of filamentation can be controlled continuously by changing the laser power and divergence angle of the laser beam. An analytical model for the process is given.

近衍射极限半导体激光束波面检测

在星间半导体激光通信系统中，如何检测发射光束波面的质量是个较难处理的问题，为了较好地解决这一问题，在简单介绍白光横向双剪切干涉仪的基础上，报道了用此干涉仪对近衍射极限半导体激光光束波面的检测，在此基础上推导出计算远场发散度的公式。实验测得近场光束的波高差为0．2A，通过夫朗和费衍射求得光束的发散度仅为64．8μrad，这表明光束接近光学衍射极限。同时，表明双剪切干涉仪灵敏度高、实用性好。

Series representation of the Gaussian beam far-field diffracted by annular aperture

Accurate, analytical series expressions for the far-field diffraction of it Gaussian beam normally incident on a circular and central obscured aperture are derived with the help of the integration of parts method. With this expression, the far-field intensity distribution pattern can be obtained and the divergence angle is deduced too. Using the first five items of the series, the accuracy can satisfy most laser application fields. Compared with the conventional numerical integral method, the series representation is very convenient for understanding the physical meanings. (C) 2007 Elsevier GmbH. All rights reserved.

激光束质量实时测量技术

提出一种新型光束质量实时测量技术, 该技术主要基于由平板反射镜组成的多平面成像系统, 一次性将激光束腰附近2倍瑞利距离内的多个光斑成像在同一个平面上, 用CCD相机获取这些光斑的光强分布图样。通过图像处理获知接收到的光斑的光强分布。采用远场发散角、焦点尺寸、桶中功率比和M2因子四种光束质量评价标准对激光光束质量进行评价。利用该方法实时测量了高能钕玻璃双板条激光器的输出光束。

部分端面抽运板条激光器腔镜倾斜问题研究

部分端面抽运的板条激光器是一种新型固体激光器．配合混合腔可以实现在大功率下保持高光束质量的激光振荡输出。谐振腔的腔镜倾斜是影响激光器输出特性的重要因素，快速傅里叶方法是一种快捷有效的计算方法，利用此方法模拟了腔镜倾斜对近场相位分布和远场光强分布的影响，并分析了光束质量的变化。理论分析表明，腔镜的小角度倾斜对近场相位影响较大，但对远场光强空间分布影响不大；随着倾斜角度不断增大，远场发散角和光束腰宽度也增大，光束质量虽然存在恶化的趋势，但光束质量因子肝值仍然较小，离轴非稳腔仍能保持高光束质量的输出。

基于正交频率变换的高功率蓝绿全固态激光器

对多横模全固态激光器使用正交频率变换进行了分析,计算了频率转换效率与激光发散角的关系。使用双KTP晶体正交倍频的方法,对Nd∶YAG激光器输出的含有高阶横模的激光进行倍频实验研究。在1064 nm Nd∶YAG激光基波功率密度为121 MW/cm2时,其谐波转换效率达到75.5%。研究表明,对于光束质量较差的基波激光,采用正交频率变换的方式,适当选择晶体参数,同样可以获得较高效率的二次谐波输出。

侧面抽运国产Nd∶YAG陶瓷棒的激光特性

实验研究了激光二极管阵列(LDA)侧向抽运国产Nd∶YAG陶瓷棒的准连续及被动调Q激光输出特性。该陶瓷激光器采用LDA侧面紧密环绕均匀排布的抽运结构,陶瓷棒抽运区域长度为20 mm,其总尺寸为3 mm×35 mm,掺杂原子数分数为~1%。在千赫兹准连续运转条件下,当平-平谐振腔的输出耦合镜透过率为47.3%时,获得最大平均功率23 W的1064 nm激光输出,光束发散角为4.5 mrad,斜率效率达12%。在谐振腔内插入Cr4+∶YAG晶体作为被动调Q开关,成功地实现了陶瓷激光器千赫兹重复频率调Q激光脉冲输出,当Cr4+∶YAG晶体初始透过率为60%时,输出激光脉冲宽度(半峰全宽)可窄至14.5 ns,调Q动静比约为40%。

Kilohertz electro-optic Q-switched Nd : YAG ceramic laser

We investigate the lasing characteristics of a laser-diode-array side-pumped electro-optic Q-switched Nd:Y3Al5O12 ceramic laser operating at 1000 Hz pulse repetition rate. Using a YAG poltcrystalline rod with Nd3+ concentration at 1 at.% as the gain medium, pumping with 808 nm laser-diode-arrays, the Q-switched laser output at 1064 nm wavelength with 23 mJ pulse energy and less than 12 ns FWHM pulse width are obtained at a pumping power of about 400 W, the slope efficiency is around 15%, the output beam divergence angle is about 1.2 mrad.

InnoSlab混合腔输出光束质量的理论研究

对InnoSlab Laser用混合腔的输出光束质量问题从热透镜效应和腔镜的不对准两个方面的影响进行理论分析,并从远场光强分布、远场发散角、光腰半径、光束质量因子M2值和桶中功率曲线等几个角度进行了讨论,特别是离轴非稳腔方向上腔镜倾斜对光束质量的影响,利用M2值和PIB曲线两个参数共同评价非稳腔的光束质量,对目前并无统一标准的非稳腔光束质量评价问题提供了有意义的参考.

Micro-vortex generator flow control for supersonic engine inlets

To investigate the flow control potential of micro-vortex generators for supersonic mixed-compression inlets, a basic model experiment has been designed which combines a normal shock wave with a subsonic diffuser. The diffuser is formed by a simple expansion corner, with a divergence angle of 6 degrees. The diffuser entry Mach numbers were M=1.3 and M=1.5 and a number of shock locations relative to the corner position were tested. Flow control was applied in the form of counter-rotating micro-vanes with heights of approximately 20% of boundary layer thickness. Furthermore, corner fences where employed to reduce sidewall effects. It was found that micro-vortex generators were able to significantly reduce the extent of flow separation under all conditions, but could not eliminate it altogether. Corner fences also demonstrated potential for improving the flow in rectangular cross section channels and the combination of corner fences with micro-vortex generators was found to give the greatest benefits. At M=1.3 the combination of corner fences and micro-vanes placed close to the diffuser entry could prevent separation for a wide range of conditions. At the higher diffuser entry Mach number the benefits of flow control were less significant although a reduction of separation size and an improved pressure recovery was observed. It is thought that micro-vortex generators can have significant flow control potential if they are placed close to the expected separation onset and when the adverse pressure gradient is not too far above the incipient separation level. The significant beneficial effects of corner fences warrant a more comprehensive further investigation. It is thought that the control methods suggested here are capable of reducing the bleed requirement on an inlet, which could provide significant performance advantages.