Cloud-point extraction of phenanthrene by nonionic surfactants

Extraction and preconcentration of the model polycyclic aromatic hydrocarbon (PAH), phenanthrene, in aqueous solutions by two different kinds of nonionic ethoxylated alcohols, Tergitol 15-S-7 and Neodol 25-7, as extractants was studied at ambient temperature (22°C). Both surfactants have almost the same numbers of hydrocarbons and ethylene-oxide (EO) units, but differ in the location of the alcohols. Neodol 25-7 is a primary alcohol, while Tergitol 15-S-7 is a secondary one. The extraction process is based on the clouding phenomena of these two nonionic surfactants. Addition of sodium sulfate or sodium phosphate could decrease the cloud point temperatures of the surfactant solutions below the ambient temperatures, so that the cloud-point extraction process could be facilitated. Increasing the salt concentration or decreasing the surfactant concentration could improve the preconcentration factor, which is attributable to the decrease in the volume of surfactant-rich phase. Consequently, the recovery efficiency higher than 96% was achieved for phenanthrene in aqueous solution.

A novel cloud-point extraction process for preconcentrating selected polycyclic aromatic hydrocarbons in aqueous solution

A novel but simple cloud-point extraction (CPE) process is developed to preconcentrate the trace of selected polycyclic aromatic hydrocarbons (PAHs) with the use of the readily biodegradable nonionic surfactant Tergitol 15-S-7 as extractant. The concentrations of PAHs, mixtures of naphthalene and phenanthrene as well as pyrene, in the spiked samples were determined with the new CPE process at ambient temperature (23 °C) followed by high performance liquid chromatography (HPLC) with fluorescence detection. More than 80% of phenanthrene and pyrene, respectively, and 96% of naphthalene initially present in the aqueous solutions with concentrations near or below their aqueous solubilities were recovered using this new CPE process. Importantly Tergitol 15-S-7 does not give any fluorometric signal to interfere with fluorescence detection of PAHs in the UV range. No special washing step is, thus, required to remove surfactant before HPLC analyses. Different experimental conditions were studied. The optimum conditions for the preconcentration and determi nation of these selected PAHs at ambient temperature have been established as the following:  (1) 3 wt % surfactant; (2) addition of 0.5 M Na2SO4; (3) 10 min for equilibration time; and (4) 3000 rpm for centrifugal speed with duration of 10 min.

Behavior of Triton X-114 cloud point in the presence of inorganic electrolytes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Process for producing biodiesel fuel with reduced viscosity and a cloud point below thirty-two (32) degrees fahrenheit

Triglycerides are reacted in a liquid phase reaction with methanol and a homogeneous basic catalyst. The reaction yields a spatially separated two phase result with an upper located non-polar phase consisting principally of non-polar methyl esters and a lower located phase consisting principally of glycerol and residual methyl esters. The glycerol phase is passed through a strong cationic ion exchanger to remove anions, resulting in a neutral product which is flashed to remove methanol and which is reacted with isobutylene in the presence of a strong acid catalyst to produce glycerol ethers. The glycerol ethers are then added back to the upper located methyl ethyl ester phase to provide an improved biodiesel fuel.

An environmentally friendly analytical procedure for nickel determination by atomic and molecular spectrometry after cloud point extraction in different samples

Cloud point extraction (CPE) was employed for separation and preconcentration prior to the determination of nickel by graphite furnace atomic absorption spectrometry (GFAAS), flame atomic absorption spectrometry (FAAS) or UV-Vis spectrophotometry. Di-2-pyridyl ketone salicyloylhydrazone (DPKSH) was used for the first time as a complexing agent in CPE. The nickel complex was extracted from the aqueous phase using the Triton X-114 surfactant. Under optimized conditions, limits of detection obtained with GFAAS, FAAS and UV-Vis spectrophotometry were 0.14, 0.76 and 1.5 mu g L-1, respectively. The extraction was quantitative and the enrichment factor was estimated to be 27. The method was applied to natural waters, hemodialysis concentrates, urine and honey samples. Accuracy was evaluated by analysis of the NIST 1643e Water standard reference material.

On the modelling of the thermal interactions between a spray curtain and an impinging cold gas cloud

A mixed Lagrangian-Eulerian model of a Water Curtain barrier is presented. The heat, mass and momentum processes are modelled in a Lagrangian framework for the dispersed phase and in an Eulerian framework for the carrier phase. The derivation of the coupling source terms is illustrated with reference to a given carrier phase cell. The turbulent character of the flow is treated with a single equation model, modified to directly account for the influence of the particles on the flow. The model is implemented in the form of a 2 D incompressible Navier Stokes solver, coupled to an adaptive Rung Kutta method for the Lagrangian sub-system. Simulations of a free standing full cone water spray show satisfactory agreement with experiment. Predictions of a Water Curtain barrier impacted by a cold gas cloud point to markedly different flow fields for the upward and downward configurations, which could influence the effectiveness of chemical absorption in the liquid phase.

Effects of additives on the cloud points of selected nonionic linear ethoxylated alcohol surfactants

Effects of various additives including inorganic salts, nonionic and ionic surfactants, water-soluble polymers and alcohols on the cloud points of three linear nonionic surfactants, Tergitol 15-S-7, Tergitol 15-S-9 and Neodol 25-7, were investigated. These surfactants are readily biodegradable and either linear primary or secondary ethoxylated alcohols. Cloud points of these surfactants were functions of their concentrations and concentrations of additives. The cloud points of nonionic surfactant mixtures lay in between the cloud points of individual component surfactants. Presence of two ionic surfactants, sodium dodecyl sulfate (SDS) and cetyl trimethyl ammonium bromide (CTAB), increased the cloud point of 1 wt% Tergitol 15-S-7 micellar solution dramatically when concentrations of ionic surfactants approaching their critical micelle concentration. Addition of water-soluble polymers decreased the cloud point, while addition of inorganic salts can either increase or decrease the cloud points. However, the effect of an alcohol additive on cloud point was dependent on its chain length or its water solubility. Interestingly, synergistic effects between sulfate or phosphate and pentanol on depression of cloud points of Tergitol 15-S-9 were discovered. A linear model predicting cloud points of Tergitol 15-S-X (X = 7, 9 and 12) surfactants and Neodol 25-X (X = 7, 9 and 12) surfactants were proposed with a correlation to logarithm of their ethylene oxide numbers.

Self-assembly of focal point oligo-catechol ethylene glycol dendrons on titanium oxide surfaces: adsorption kinetics, surface characterization, and nonfouling properties

This work covers the synthesis of second-generation, ethylene glycol dendrons covalently linked to a surface anchor that contains two, three, or four catechol groups, the molecular assembly in aqueous buffer on titanium oxide surfaces, and the evaluation of the resistance of the monomolecular adlayers against nonspecific protein adsorption in contact with full blood serum. The results were compared to those of a linear poly(ethylene glycol) (PEG) analogue with the same molecular weight. The adsorption kinetics as well as resulting surface coverages were monitored by ex situ spectroscopic ellipsometry (VASE), in situ optical waveguide lightmode spectroscopy (OWLS), and quartz crystal microbalance with dissipation (QCM-D) investigations. The expected compositions of the macromolecular films were verified by X-ray photoelectron spectroscopy (XPS). The results of the adsorption study, performed in a high ionic strength ("cloud-point") buffer at room temperature, demonstrate that the adsorption kinetics increase with increasing number of catechol binding moieties and exceed the values found for the linear PEG analogue. This is attributed to the comparatively smaller and more confined molecular volume of the dendritic macromolecules in solution, the improved presentation of the catechol anchor, and/or their much lower cloud-point in the chosen buffer (close to room temperature). Interestingly, in terms of mechanistic aspects of "nonfouling" surface properties, the dendron films were found to be much stiffer and considerably less hydrated in comparison to the linear PEG brush surface, closer in their physicochemical properties to oligo(ethylene glycol) alkanethiol self-assembled monolayers than to conventional brush surfaces. Despite these differences, both types of polymer architectures at saturation coverage proved to be highly resistant toward protein adsorption. Although associated with higher synthesis costs, dendritic macromolecules are considered to be an attractive alternative to linear polymers for surface (bio)functionalization in view of their spontaneous formation of ultrathin, confluent, and nonfouling monolayers at room temperature and their outstanding ability to present functional ligands (coupled to the termini of the dendritic structure) at high surface densities.

External signal-activated liposomal drug delivery systems

Modern drug discovery gives rise to a great number of potential new therapeutic agents, but in some cases the efficient treatment of patient may not be achieved because the delivery of active compounds to the target site is insufficient. Thus, drug delivery is one of the major challenges in current pharmaceutical research. Numerous nanoparticle-based drug carriers, e.g. liposomes, have been developed for enhanced drug delivery and targeting. Drug targeting may enhance the efficiency of the treatment and, importantly, reduce unwanted side effects by decreasing drug distribution to non-target tissues. Liposomes are biocompatible lipid-based carriers that have been studied for drug delivery during the last 40 years. They can be functionalized with targeting ligands and sensing materials for triggered activation. In this study, various external signal-assisted liposomal delivery systems were developed. Signals can be used to modulate drug permeation or release from the liposome formulation, and they provide accurate control of time, place and rate of activation. The study involved three types of signals that were used to trigger drug permeation and release: electricity, heat and light. Electrical stimulus was utilized to enhance the permeation of liposomal DNA across the skin. Liposome/DNA complex-mediated transfections were performed in tight rat epidermal cell model. Various transfection media and current intensities were tested, and transfection efficiency was evaluated non-invasively by monitoring the concentration of secreted reporter protein in cell culture medium. Liposome/DNA complexes produced gene expression, but electrical stimulus did not enhance the transfection efficiency significantly. Heat-sensitive liposomal drug delivery system was developed by coating liposomes with biodegradable and thermosensitive poly(N-(2-hydroxypropyl) methacrylamide-mono/dilactate polymer. Temperature-triggered liposome aggregation and contents release from liposomes were evaluated. The cloud point temperature (CP) of the polymer was set to 42 °C. Polymer-coated liposome aggregation and contents release were observed above CP of the polymer, while non-coated liposomes remained intact. Polymer precipitates above its CP and interacts with liposomal bilayers. It is likely that this induces permeabilization of the liposomal membrane and contents release. Light-sensitivity was introduced to liposomes by incorporation of small (< 5 nm) gold nanoparticles. Hydrophobic and hydrophilic gold nanoparticles were embedded in thermosensitive liposomes, and contents release was investigated upon UV light exposure. UV light-induced lipid phase transitions were examined with small angle X-ray scattering, and light-triggered contents release was shown also in human retinal pigment epithelial cell line. Gold nanoparticles absorb light energy and transfer it into heat, which induces phase transitions in liposomes and triggers the contents release. In conclusion, external signal-activated liposomes offer an advanced platform for numerous applications in drug delivery, particularly in the localized drug delivery. Drug release may be localized to the target site with triggering stimulus that results in better therapeutic response and less adverse effects. Triggering signal and mechanism of activation can be selected according to a specific application.

Avaliação de correlações para propriedades físico-químicas de frações de petróleo

O petróleo é uma mistura complexa consistindo em um número muito grande de hidrocarbonetos. A descrição completa de todos os hidrocarbonetos existentes nessas misturas é inviável experimentalmente ou consome tempo excessivo em simulações computacionais. Por esta razão, uma abordagem molecular completa para cálculos de propriedades dessas misturas é substituído por uma abordagem pseudo-componente ou por correlações entre propriedades macroscópicas. Algumas dessas propriedades são utilizadas de acordo com a regulamentação de venda de combustíveis, e.g., para gasolina. Dependendo do esquema de refino e do óleo cru utilizado para produção desse combustível, uma larga variedade de valores é encontrada para as propriedades de correntes de processo que compõe o combustível final. A fim de planejar com precisão adequada a mistura dessas correntes, modelos devem estar disponíveis para o cálculo preciso das propriedades necessárias. Neste trabalho, oito séries de combustíveis brasileiros e duas séries de combustíveis estrangeiros foram analisadas: frações de gasolina, querosene, gasóleo e diesel. As propriedades analisadas para as frações são: número de octano, teor de aromáticos, teor de enxofre, índice de refração, densidade, ponto de fulgor, ponto de fluidez, ponto de congelamento, ponto de névoa, ponto de anilina, pressão de vapor Reid e número de cetano. Diversas correlações foram avaliadas e os melhores desempenhos foram destacados, permitindo uma estimação precisa das propriedades do combustível avaliado. Um processo de re-estimação de parâmetros foi aplicado e novos modelos foram ajustados em comparação com os dados experimentais. Esta estratégia permitiu uma estimativa mais exata das propriedades analisadas, sendo verificada por um aumento considerável no desempenho estatístico dos modelos. Além disso, foi apresentado o melhor modelo para cada propriedade e cada série

Molecular weight dependence of phase Behavior of PEO/P(EO-b-DMS) blends: Application of Sanchez-Lacombe lattice fluid theory

Molecular weight dependence of phase separation behavior of the Poly (ethylene oxide) (PEO)/Poly(ethylene oxide-block-dimethylsiloxane) (P(EO-b-DMS)) blends was investigated by both experimental and theoretical methods. The cloud point curves of PEO/P(EO-b-DMS) blends were obtained by turbidity method. Based on Sanchez-Lacombe lattice fluid theory (SLLFT), the adjustable parameter, epsilon*(12)/k (quantifying the interaction energy between different components), was evaluated by fitting the experimental data in phase diagrams. To calculate the spinodals, binodals, and the volume changes of mixing for these blends, three modified combining rules of the scaling parameters for the block copolymer were introduced.