Accurate prediction of the Si/SiO(2) interface band offset using the self-consistent ab initio DFT/LDA-1/2 method

We use the density functional theory/local-density approximation (DFT/LDA)-1/2 method [L. G. Ferreira , Phys. Rev. B 78, 125116 (2008)], which attempts to fix the electron self-energy deficiency of DFT/LDA by half-ionizing the whole Bloch band of the crystal, to calculate the band offsets of two Si/SiO(2) interface models. Our results are similar to those obtained with a ""state-of-the-art"" GW approach [R. Shaltaf , Phys. Rev. Lett. 100, 186401 (2008)], with the advantage of being as computationally inexpensive as the usual DFT/LDA. Our band gap and band offset predictions are in excellent agreement with experiments.

High surface brightness dwarf galaxies in the Fornax cluster

We describe a search for compact dwarf galaxies in the Fornax cluster using the FLAIR spectrograph on the UK Schmidt Telescope. We measured radial velocities of 453 compact galaxies brighter than B-T approximate to 17.3 and found seven new compact dwarf cluster members that were not classified in previous surveys as members of the cluster. These are amongst the most compact, high surface brightness dwarf galaxies known. The inclusion of these galaxies in the cluster does not change the total luminosity function significantly, but they are important because of their extreme nature; one in particular appears to be a dwarf spiral. Three of the new dwarfs have strong emission lines and we identify them as blue compact dwarfs (BCDs), doubling the number of confirmed BCDs in the cluster. We also determined that none of the compact dwarf elliptical (M32-like) candidates is in the cluster, down to an absolute magnitude M-B = -13.2. We have investigated the claim of Irwin et al. that there is no strong relation between surface brightness and magnitude for the cluster members and find some support for this for the brighter galaxies (B-T < 17.3), but fainter galaxies still need to be measured.

SIR performance evaluation of MB-OFDM UWB system with residual timing offset

Signal-to-interference ratio (SIR) performance of a multiband orthogonal frequency division multiplexing ultra-wideband system with residual timing offset is investigated. To do so, an exact mathematical derivation of the SIR of this system is derived. It becomes obvious that, unlike a cyclic prefixing based system, a zero padding based system is sensitive to residual timing offset.

Fracture imaging within a granitic rock aquifer using multiple-offset single-hole and cross-hole GPR reflection data

The sparsely spaced highly permeable fractures of the granitic rock aquifer at Stang-er-Brune (Brittany, France) form a well-connected fracture network of high permeability but unknown geometry. Previous work based on optical and acoustic logging together with single-hole and cross-hole flowmeter data acquired in 3 neighbouring boreholes (70-100 m deep) has identified the most important permeable fractures crossing the boreholes and their hydraulic connections. To constrain possible flow paths by estimating the geometries of known and previously unknown fractures, we have acquired, processed and interpreted multifold, single- and cross-hole GPR data using 100 and 250 MHz antennas. The GPR data processing scheme consisting of timezero corrections, scaling, bandpass filtering and F-X deconvolution, eigenvector filtering, muting, pre-stack Kirchhoff depth migration and stacking was used to differentiate fluid-filled fracture reflections from source generated noise. The final stacked and pre-stack depth-migrated GPR sections provide high-resolution images of individual fractures (dipping 30-90°) in the surroundings (2-20 m for the 100 MHz antennas; 2-12 m for the 250 MHz antennas) of each borehole in a 2D plane projection that are of superior quality to those obtained from single-offset sections. Most fractures previously identified from hydraulic testing can be correlated to reflections in the single-hole data. Several previously unknown major near vertical fractures have also been identified away from the boreholes.

High-SNR power offset in multiantenna communication

The analysis of the multiantenna capacity in the high-SNR regime has hitherto focused on the high-SNR slope (or maximum multiplexing gain), which quantifies the multiplicative increase as function of the number of antennas. This traditional characterization is unable to assess the impact of prominent channel features since, for a majority of channels, the slope equals the minimum of the number of transmit and receive antennas. Furthermore, a characterization based solely on the slope captures only the scaling but it has no notion of the power required for a certain capacity. This paper advocates a more refined characterization whereby, as function of SNRjdB, the high-SNR capacity is expanded as an affine function where the impact of channel features such as antenna correlation, unfaded components, etc, resides in the zero-order term or power offset. The power offset, for which we find insightful closed-form expressions, is shown to play a chief role for SNR levels of practical interest.

Surface topography and mixed-pixel effects on the simulated L-band brightness temperatures.

The impact of topography and mixed pixels on L-band radiometric observations over land needs to be quantified to improve the accuracy of soil moisture retrievals. For this purpose, a series of simulations has been performed with an improved version of the soil moisture and ocean salinity (SMOS) end-to-end performance simulator (SEPS). The brightness temperature generator of SEPS has been modified to include a 100-m-resolution land cover map and a 30-m-resolution digital elevation map of Catalonia (northeast of Spain). This high-resolution generator allows the assessment of the errors in soil moisture retrieval algorithms due to limited spatial resolution and provides a basis for the development of pixel disaggregation techniques. Variation of the local incidence angle, shadowing, and atmospheric effects (up- and downwelling radiation) due to surface topography has been analyzed. Results are compared to brightness temperatures that are computed under the assumption of an ellipsoidal Earth.

Low environmental impact bleaching sequences for attaining high brightness level with eucalyptus SPP pulp

The alternatives used for minimizing the usage of chlorine dioxide in bleaching sequences included a hot acid hydrolysis (Ahot) stage, the use of hot chlorine dioxide (Dhot) and ozone stages at medium consistency and high consistency (Zmc and Zhc), in addition to stages with atmospheric hydrogen peroxide (P) and pressurized hydrogen peroxide (PO). The results were interpreted based on the cost of the chemical products, bleaching process yields and on minimizing the environmental impact of the bleaching process. In spite of some process restrictions, high ISO brightness levels were kept around 90 % brightness. Additionally, the inclusion of stages like acid hydrolysis, pressurized peroxide and ozone in the bleaching sequences provided an increase in operating flexibility, aimed at reducing environmental impact (ECF Light). The Dhot(EOP)D(PO) sequence presented lower operating cost for ISO brightness above 92 %. However, this kind of sequence was not allowed for closing the wastewater circuit, even partially. For ISO brightness level around 91%, the AhotZhcDP sequence presented a lower operating cost than the others

Kuivatusmenetelmien vaikutus heatset offset- ja syväpainetun SC-paperin laatuun

Työssä tutkittiin heatset offset- ja syväpainetun SC-paperin painojäljen laatua, kun koepaperikoneella valmistetun SC-paperin valmistuksessa käytettiin eri kuivatus-menetelmiä. Erityisesti kiinnostus kohdistui eri kuiva-ainepitoisuuksissa käytetyn ilmakuivatuksen aiheuttamiin painojäljen laatuvaikutuksiin. Painojäljen lisäksi työssä tarkasteltiin pohjapaperin ominaisuuksia kuivatuksen jakalanteroinnin jälkeen. Perinteisen sylinterikuivatuksen kuivatuskapasiteettia voidaan nostaa kuivattamalla paperia kuuman ilman avulla, jolloin paperin haihdutusnopeus nousee yli viisinkertaiseksi sylinterikuivatukseenverrattuna. Ilmakuivatus voidaan sijoittaa välittömästä kuivatusosan alkuun ennen ensimmäistä kuivatussylinteriä tai korkeampaan kuiva-ainepitoisuuteen sylinterikuivatuksen keskelle. Kuivattua paperia tarkasteltaessa kuuman ilman avulla kuivatun paperin ominaisuudet poikkesivat huokoisuuden ja öljynabsorption suhteen sylinterikuivatusta paperista sekä heatset offset- että syväpainopaperilla. Kalanterointi tasoitti koepisteiden välisiä muutoksia. Kalanteroidusta paperista havaittiin, että ilmakuivatuksen sijoittuminen välittömästi puristimen jälkeen kasvatti paperin molempien pintojen opasiteettia. Vastaavasti paperin tiheys kasvoi, kun paperia kuivattiin kuumalla ilmalla sekä ennen sylinterikuivatusta että sylinterikuivatuksen keskellä. Yhteistä ilmakuivatuksen käytölle kaikissa koepisteissä oli paperin huokoisuuden pieneneminen. Heatset offsetpainoprosessissa käytettävä kostutusvesi asettaa paperin kuitu-karhenemiselle vaatimuksia. Tutkimuksessa havaittiin, että puristimen jälkeen sijoitettu ilmakuivatus pienensi paperin taipumusta karhentua painoprosessissa. Muiden ominaisuuksien osalta paperin kuivatus kuuman ilman avulla yhdessä sylinterikuivatuksen kanssa ei jättänyt paperiin sellaisia jälkiä, jotka näkyisivät heatset offset- ja syväpainetun SC-paperin painojäljessä verrattuna kokonaan yksiviira-vientisesti sylinterikuivattuun paperiin.

Suomalaisen kotikeräyspaperin siistattavuus

Tämän diplomityön tavoitteena oli kartoittaa kotikeräyspaperin lajijakautumisesta ja eri jakeiden ikääntymiskäyttäytymisestä johtuvien siistausongelmien syyt sekä tutkia tulevaisuuden painotekniikan kehitystrendien asettamia vaatimuksia siistauslaitosten kannalta. Kirjallisuusosassa tarkasteltiin siistauksen sekä erilaisten painatustekniikoiden teoriaa. Lisäksi siinä tarkasteltiin erilaisia siistattavuuteen vaikuttavia tekijöitä. Kirjallisuusosassa luotiin katsaus viimeaikaisiin painatuksen kehityksiin Suomessa sekä kartoitettiin painatuksen lähitulevaisuutta. Myös tulevaisuuden näkymiä siistauslaitosten kannalta tarkasteltiin. Kokeellisessa osassa tutkittiin suomalaisen kotikeräyspaperin siistattavuusominaisuuksia pian painamisen jälkeen sekä kolmen ja kuuden kuukauden vanhentamisen kuluttua. Esitutkimusten perusteella siistattaviksi valittiin useita coldset offset painettuja sanomalehtiä, sekä kaksi syväpainettua ja yksi heatset offset painettu aikakauslehti. Kyseisten painotuotteiden siistattavuus-ominaisuuksia tarkasteltiin laboratoriomittakaavaisissa pulpperoinneissa sekä osin flotatoinneissa. Erilaisten painotuotteiden siistattavuutta tarkasteltiin ISO-vaaleus-, k700nm-arvo-, ERIC-arvo-, CIE L*a*b*- ja lika- ja painoväripilkkumittausten avulla. Tutkittujen painotuotteiden kierrätysominaisuudet vaihtelivat niin tuoreena kuin vanhennettunakin helposti siistattavista jo tuoreena vaikeasti siistattavaan. Hyvän tuloksen koko vanhentamisen keston ajan antoivat suomalaiset aikakauslehdet sekä osa sanomalehdistä. Laboratoriotutkimuksissa havaittiin että painotalojen käyttämien painovärien, erityisesti värillisten painovärien, valinnalla on suuri vaikutus valmiin painotuotteen uusiokäyttöön. Tämän diplomityön antamien tulosten perusteella voidaan sanoa, että kotimaisen keräyspaperin viimeaikaiseen siistattavuuden heikkenemiseen on vaikuttanut eniten coldset offset painotuotteiden suuresti lisääntynyt väripainatuksen määrä.

Offset-print mottling measurement using machine vision

Mottling is one of the key defects in offset-printing. Mottling can be defined as unwanted unevenness of print. In this work, diameter of a mottle spot is defined between 0.5-10.0 mm. There are several types of mottling, but the reason behind the problem is still not fully understood. Several commercial machine vision products for the evaluation of print unevenness have been presented. Two of these methods used in these products have been implemented in this thesis. The one is the cluster method and the other is the band-pass method. The properties of human vision system have been taken into account in the implementation of these two methods. An index produced by the cluster method is a weighted sum of the number of found spots, and an index produced by band-pass method is a weighted sum of coefficients of variations of gray-levels for each spatial band. Both methods produce larger indices for visually poor samples, so they can discern good samples from the poor ones. The difference between the indices for good and poor samples is slightly larger produced by the cluster method. 11 However, without the samples evaluated by human experts, the goodness of these results is still questionable. This comparison will be left to the next phase of the project.

Brightness of multilayer boards

A good appearance of a package enhances the sale of the product. The packing gives information about the content and instructions for the usage. In this master’s thesis, the optical properties of multilayer packaging board is studied. Especially means of increasing brightness of the multilayer board are evaluated. In the literature part, the effect of different factors on optical properties of a multilayer board are evaluated with the help of light scattering and absorption coefficients. The Kubelka-Munk theory can be used also in modelling brightness of the multilayer board. A large variety of different process factors, chemical aids and machine variables affect optical properties of board. In the experimental part, different methods to increase brightness of a 3-layer board were evaluated. It was discovered that brightness variation of broke (30 % share of the center layer pulp) have only minor influence on brightness of the board. The brightness variation must be high, roughly 9 % in order to alter brightness of the board by 1 %. Higher brightness can be achieved by bleaching the pulp, which holds the largest share of the center layer pulp. Here, 2,6 % increase in brightness of the pulp (60 % share of the center layer pulp) increased brightness of the board by 1 %. In a trial run at a board machine, there was no indication of decreased bulk of the board due to extended bleaching of the pulp. With pulp dyeing appearance and optical properties of a multilayer board can be influenced. By using bluish dyes the natural yellowness of pulps can be decreased and impression of whiteness is then increased. Brightness may deteriorate though, because of increasing light absorption of the dyed pulps. When the yellowness comes from the center layer pulp, the dye should be introduced there. Then the brightness decreasing effect of the dye decreases brightness of the board less. It was noticed that it is more important to maintain brightness of the top layer than brightness of the center layer, because the top layer pulp affects on brightness of the board the most. By introducing fillers into the top layer of a multilayer board it is possible to increase brightness of the board. Fillers with the highest light scattering increased the brightness of the board the most. Increasing light scattering increases brightness and also opacity. Higher opacity in the top layer decreases also the darkening effect of the center layer. Calcinated kaolin and PCC was found to increase the light scattering of the top layer the most at the filler comparison. Introducing fillers into the top layer of multilayer board may decrease bulk and modulus of elasticity of the top layer. This could lead to deteriorated bending stiffness.

Water circulations for effective bleaching of high-brightness mechanical pulps

The amount of water available is usually restricted, which leads to a situation where a complete understanding of the process, including water circulations and the influence of water components, is essential. The main aim of this thesis was to clarify the possibilities for the efficient use of residual peroxide by means of water circulation rearrangements. Rearranging water circulations and the reduction of water usage may cause new problems, such as metal induced peroxide decomposition that needs to be addressed. This thesis introduces theoretical methods of water circulations to combine two variables; effective utilization of residual peroxide and avoiding manganese in the alkaline peroxide bleaching stage. Results are mainly based on laboratory and mill site experiments concerning the utilization of residual peroxide. A simulation model (BALAS) was used to evaluate the manganese contents and residual peroxide doses. It was shown that with optimum recirculation of residual peroxide the brightness can be improved or chemical costs can be decreased. From the scientific perspective, it was also very important to discover that recycled peroxide was more effective pre-bleaching agent compared to fresh peroxide. This can be due to the organic acids i.e. per acetic acid in wash press filtrate that have been formed in alkaline bleaching stage. Even short retention time was adequate and the activation of residual peroxide using sodium hydroxide was not necessary. There are several possibilities for using residual peroxide in practice regarding bleaching. A typical modern mechanical pulping process line consist of defibering, screening, a disc filter, a bleach press, high consistency (HC) peroxide bleaching and a wash press. Furthermore there usually is not a particular medium consistency (MC) pre-bleaching stage that includes additional thickening equipment. The most advisable way to utilize residual peroxide in this kind of process is to recycle the wash press filtrate to the dilution of disc filter pulp (low MC pre-bleaching stage). An arrangement such as this would be beneficial in terms of the reduced convection of manganese to the alkaline bleaching stage. Manganese originates from wood material and will be removed to the water phase already in the early stages of the process. Recycling residual peroxide prior to the disc filter is not recommended because of low consistencies. Regarding water circulations, the novel point of view is that, it would be beneficial to divide water circulations into two sections and the critical location for the division is the disc filter. Both of these two sections have their own priority. Section one before the disc filter: manganese removal. Section two after the disc filter: brightening of pulp. This division can be carried out if the disc filter pulp is diluted only by wash press filtrate before the MC storage tower. The situation is even better if there is an additional press after the disc filter, which will improve the consistency of the pulp. This has a significant effect on the peroxide concentration in the MC pre-bleaching stage. In terms of manganese content, it is essential to avoid the use of disc filter filtrate in the bleach press and wash press showers. An additional cut-off press would also be beneficial for manganese removal. As a combination of higher initial brightness and lower manganese content, the typical brightness increase varies between approximately 0.5 and 1% ISO units after the alkaline peroxide bleaching stage. This improvement does not seem to be remarkable, but as it is generally known, the final brightness unit is the most expensive and difficult to achieve. The estimation of cost savings is not unambiguous. For example in GW/TMP mill case 0.6% ISO units higher final brightness gave 10% savings in the costs of bleaching chemicals. With an hypothetical 200 000 ton annual production, this means that the mill could save in the costs of bleaching chemicals more than 400 000 euros per year. In general, it can be said that there were no differences between the behavior of different types of processes (GW, PGW, TMP and BCTMP). The enhancement of recycling gave a similar response in all cases. However, we have to remember that the utilization of residual peroxide in older mills depends a great deal on the process equipment, the amount of water available and existing pipeline connections. In summary, it can be said that processes are individual and the same solutions cannot be applied to all cases.

The role of bound chlorine in the brightness reversion of bleached hardwood kraft pulp

Our previous paper showed fragmentary evidence that pulp brightness reversion may be negatively affected by its organically bound chlorine (OX) content. A thorough investigation on eucalyptus kraft pulp led to the conclusion that OX increases reversion of certain pulps but this trend is not universal. Alkaline bleaching stages decrease reversion regardless of pulp OX content. Pulps bleached with high temperature chlorine dioxide revert less than those bleached with conventional chlorine dioxide in sequences ending with a chlorine dioxide stage but similarly in sequences ending with a final peroxide stage. The use of secondary condensate for pulp washing decreases reversion.

Influence of plasma modification on surface properties and offset printability of coated paper

The properties of the paper surface play a crucial role in ensuring suitable quality and runnability in various converting and finishing operations, such as printing. Plasma surface modification makes it possible to modify the surface chemistry of paper without altering the bulk material properties. This also makes it possible to investigate the role of the surface chemistry alone on printability without influencing the porous structure of the pigment-coated paper. Since the porous structure of a pigment coating controls both ink setting and optical properties, surface chemical changes created by a plasma modification have a potential to decouple these two effects and to permit a better optimization of them both. The aim of this work was to understand the effects of plasma surface modification on paper properties, and how it influences printability in the sheet-fed offset process. The objective was to broaden the fundamental understanding of the role of surface chemistry on offset printing. The effects of changing the hydrophilicity/ hydrophobicity and the surface chemical composition by plasma activation and plasma coatings on the properties of coated paper and on ink-paper interactions as well as on sheet-fed offset print quality were investigated. In addition, the durability of the plasma surface modification was studied. Nowadays, a typical sheet-fed offset press also contains units for surface finishing, for example UVvarnishing. The role of the surface chemistry on the UV-varnish absorption into highly permeable and porous pigment-coated paper was also investigated. With plasma activation it was possible to increase the surface energy and hydrophilicity of paper. Both polar and dispersion interactions were found to increase, although the change was greater in the polar interactions due to induced oxygen molecular groups. The results indicated that plasma activation takes place particularly in high molecular weight components such as the dispersion chemicals used to stabilize the pigment and latex particles. Surface composition, such as pigment and binder type, was found to influence the response to the plasma activation. The general trend was that pilot-scale treatment modified the surface chemistry without altering the physical coating structure, whereas excessive laboratory-scale treatment increased the surface roughness and reduced the surface strength, which led to micro-picking in printing. It was shown that pilot-scale plasma activation in combination with appropriate ink oils makes it possible to adjust the ink-setting rate. The ink-setting rate decreased with linseed-oil-based inks, probably due to increased acid-base interactions between the polar groups in the oil and the plasma-treated paper surface. With mineral-oil-based inks, the ink setting accelerated due to plasma activation. Hydrophobic plasma coatings were able to reduce or even prevent the absorption of dampening water into pigmentcoated paper, even when the dampening water was applied under the influence of nip pressure. A uniform hydrophobic plasma coating with sufficient chemical affinity with ink gave an improved print quality in terms of higher print density and lower print mottle. It was also shown that a fluorocarbon plasma coating reduced the free wetting of the UV-varnish into the highly permeable and porous pigment coating. However, when the UV-varnish was applied under the influence of nip pressure, which leads to forced wetting, the role of the surface chemical composition seems to be much less. A decay in surface energy and wettability occurred during the first weeks of storage after plasma activation, after which it leveled off. However, the oxygen/carbon elemental ratio did not decrease as a function of time, indicating that ageing could be caused by a re-orientation of polar groups or by a contamination of the surface. The plasma coatings appeared to be more stable when the hydrophobicity was higher, probably due to fewer interactions with oxygen and water vapor in the air.

The effect of wood supply and bleaching process on pulp brightness stability

One hundred different 5.5-year-old Eucalyptus grandis x Eucalyptus urophylla wood clones were cooked to kappa number 15-17.5 and the resulting kraft pulps oxygen-delignified to kappa 9.5-11.5 under fixed conditions, except for chemical charges. Thirteen samples showing large variations in effective alkali requirement, pulp yield and O-stage efficiency and selectivity were selected for brightness reversion studies. These samples were bleached to 90-91% ISO by DEDD and DEDP sequences and their brightness stability and chemical characteristics determined. Heat reversion of the eucalyptus kraft pulps was strongly influenced by the wood supply, with brightness loss varying in the range of 2.1-3.6 and 0.8-1.7 %ISO for ODEDD and ODEDP bleached pulps, respectively. Pulps bleached by the ODEDP sequence showed reversion values 1.3-1.9 % ISO lower than those bleached by the ODEDD sequence. Pulp carbonyl content decreased by 35-40% during the final peroxide bleaching stage. Carbonyl and carboxyl groups correlated positively with brightness reversion, as did permanganate number and acid soluble lignin. Pulp final viscosity and metal and DCM extractives contents showed no significant correlation with brightness reversion. Pulping, oxygen delignification and ECF bleaching performances also showed no correlation with brightness reversion.