960 resultados para bottom ash
Resumo:
The main goal of this paper is to obtain a granular material formulated with Municipal Solid Waste Incinerarion (MSWI) bottom ash (BA) and air pollution control (APC) ash to be used as secondary building material. Previously, an optimum concrete mixture using both MSWI residues as aggregates was formulated. A compromise between the environmental behaviour and the economy of the process was considered. Unconfined compressive strength and abrasion resistance values were measured in order to evaluate the mechanical properties. From these results, the granular mixture was not suited for certain applications owing to the high BA/APC content and low cement percentages used to reduce the costs of the final product. Nevertheless, the leaching test performed showed that the concentrations of all heavy metals were below the limits established by the current Catalan legislation for their reutilization. Therefore, the material studied might be mainly used in embankments, where high mechanical properties are not needed and environmental safety is assured.
Resumo:
The main goal of this paper is to obtain a granular material formulated with Municipal Solid Waste Incinerarion (MSWI) bottom ash (BA) and air pollution control (APC) ash to be used as secondary building material. Previously, an optimum concrete mixture using both MSWI residues as aggregates was formulated. A compromise between the environmental behaviour and the economy of the process was considered. Unconfined compressive strength and abrasion resistance values were measured in order to evaluate the mechanical properties. From these results, the granular mixture was not suited for certain applications owing to the high BA/APC content and low cement percentages used to reduce the costs of the final product. Nevertheless, the leaching test performed showed that the concentrations of all heavy metals were below the limits established by the current Catalan legislation for their reutilization. Therefore, the material studied might be mainly used in embankments, where high mechanical properties are not needed and environmental safety is assured.
Resumo:
The present world energy production is heavily relying on the combustion of solid fuels like coals, peat, biomass, municipal solid waste, whereas the share of renewable fuels is anticipated to increase in the future to mitigate climate change. In Finland, peat and wood are widely used for energy production. In any case, the combustion of solid fuels results in generation of several types of thermal conversion residues, such as bottom ash, fly ash, and boiler slag. The predominant residue type is determined by the incineration technology applied, while its composition is primarily relevant to the composition of fuels combusted. An extensive research has been conducted on technical suitability of ash for multiple recycling methods. Most of attention was drawn to the recycling of the coal combustion residues, as coal is the primary solid fuel consumed globally. The recycling methods of coal residues include utilization in a cement industry, in concrete manufacturing, and mine backfilling, to name few. Biomass combustion residues were also studied to some extent with forest fertilization, road construction, and road stabilization being the predominant utilization options. Lastly, residues form municipal solid waste incineration attracted more attention recently following the growing number of waste incineration plants globally. The recycling methods of waste incineration residues are the most limited due to its hazardous nature and varying composition, and include, among others, landfill construction, road construction, mine backfilling. In the study, environmental and economic aspects of multiple recycling options of thermal conversion residues generated within a case-study area were studied. The case-study area was South-East Finland. The environmental analysis was performed using an internationally recognized methodology — life cycle assessment. Economic assessment was conducted applying a widely used methodology — cost-benefit analysis. Finally, the results of the analyses were combined to enable easier comparison of the recycling methods. The recycling methods included the use of ash in forest fertilization, road construction, road stabilization, and landfill construction. Ash landfilling was set as a baseline scenario. Quantitative data about the amounts of ash generated and its composition was obtained from companies, their environmental reports, technical reports and other previously published literature. Overall, the amount of ash in the case-study area was 101 700 t. However, the data about 58 400 t of fly ash and 35 100 t of bottom ash and boiler slag were included in the study due to lack of data about leaching of heavy metals in some cases. The recycling methods were modelled according to the scientific studies published previously. Overall, the results of the study indicated that ash utilization for fertilization and neutralization of 17 600 ha of forest was the most economically beneficial method, which resulted in the net present value increase by 58% compared to ash landfilling. Regarding the environmental impact, the use of ash in the construction of 11 km of roads was the most attractive method with decreased environmental impact of 13% compared to ash landfilling. The least preferred method was the use of ash for landfill construction since it only enabled 11% increase of net present value, while inducing additional 1% of negative impact on the environment. Therefore, a following recycling route was proposed in the study. Where possible and legally acceptable, recycle fly and bottom ash for forest fertilization, which has strictest requirements out of all studied methods. If the quality of fly ash is not suitable for forest fertilization, then it should be utilized, first, in paved road construction, second, in road stabilization. Bottom ash not suitable for forest fertilization, as well as boiler slag, should be used in landfill construction. Landfilling should only be practiced when recycling by either of the methods is not possible due to legal requirements or there is not enough demand on the market. Current demand on ash and possible changes in the future were assessed in the study. Currently, the area of forest fertilized in the case-study are is only 451 ha, whereas about 17 600 ha of forest could be fertilized with ash generated in the region. Provided that the average forest fertilizing values in Finland are higher and the area treated with fellings is about 40 000 ha, the amount of ash utilized in forest fertilization could be increased. Regarding road construction, no new projects launched by the Center of Economic Development, Transport and the Environment in the case-study area were identified. A potential application can be found in the construction of private roads. However, no centralized data about such projects is available. The use of ash in stabilization of forest roads is not expected to increased in the future with a current downwards trend in the length of forest roads built. Finally, the use of ash in landfill construction is not a promising option due to the reducing number of landfills in operation in Finland.
Resumo:
Bottom ash has been used as raw material to glass and glass ceramic production because it is a source of SiO2 and Al2O3. However, the high concentration of iron (about 10% wt.) difficulty the control of the nucleation and the crystallization processes. The iron content was reduced by magnetic process, where the magnetite phase was mainly removed. In order to compare glass ceramics obtained from original and low iron bottom ashes, microstructural and dilatometric characterizations were performed.
Resumo:
Coal ashes produced in coal-fired power plant could be converted into zeolites and can be used as low-cost adsorbents for the treatment of effluents contaminated with high levels of toxic metals. The capacity of synthetic zeolites for the removal of cadmium, zinc and copper ions from aqueous solutions has been investigated under different operating conditions. Zeolite from bottom chimney showed higher removal efficiency for metals ions than zeolite from feed hopper and mixing mill. The results indicated that the treated bottom ash could be applied in environmental technology as an immobilizer of pollutants.
Resumo:
Three ash samples from an incinerator in Belo Horizonte (Brazil) were physically and chemically characterized. The chemical composition of the ashes was not always the same, neither in terms of the chemical species nor in terms of the quantities of those that are common to the three ashes. The ashes called CF1 and CF3D contain heavy metals above the detection limits of the analytical methods and the zinc concentration is high enough to justify treatment of the ashes. For these ashes, a high loss on ignition was found, indicating that the process of incineration might present failures.
Resumo:
Tavoitteena tässä diplomityössä oli selvittää Kotkan Energia Oy:n jätteenpolttolaitoksen toiminnassa syntyvän pohjakuonan hyötykäyttömahdollisuuksia ja kustannuksiltaan järkevin tapa käsitellä pohjakuona. Tarkasteltavia vaihtoehtoja hyötykäytön osalta olivat erilaiset maarakennustyöt sekä kaatopaikkojen peittäminen. Hyötykäyttövaihtoehdoille vaihtoehtoisena ratkaisuna tutkittiin kaatopaikkasijoituksen kannattavuutta. Pohjakuonan käyttöä maarakentamisessa, jätetäyttöjen peitemaina sekä pohjakuonan loppusijoitusta kaatopaikoille säätelee lainsäädäntö. Valtioneuvoston asetuksessa kaatopaikoista on määritelty loppusijoitettaville jakeille liukoisuus raja-arvot, joiden mukaisesti jätteet sijoitetaan joko pysyvän jätteen, tavanomaisen jätteen tai ongelmajätteen kaatopaikoille. Jätetäyttöjen peitemateriaalina käytettävän jakeen on myös täytettävä kyseisen kaatopaikkaluokan liukoisuusraja-arvot. Maarakennusasetus antaa puolestaan liukoisuus- ja pitoisuusraja-arvot maarakennuksessa hyödynnettäville jakeille. Pohjakuonan hyötykäyttö vaatii kuitenkin aina ympäristöluvan. Hyötyvoimalan pohjakuonasta tehtyjen analyysien perusteella voidaan todeta, että käsiteltyä pohjakuonaa olisi mahdollista käyttää esimerkiksi kenttien ja kaatopaikkojen pohjarakenteissa sekä kaatopaikoilla jätetäyttöjen peitemaina. Pohjakuonan hyödyntäminen kaukolämpötöiden maarakennuksessa vaatii vielä lisätutkimuksia putkien korroosioriskin osalta. Diplomityön tuloksena kehitettiin toimintamalli, jonka avulla Kotkan Energia Oy:n on mahdollista säästää kuonan käsittelyn ja hyötykäytön kustannuksissa. Kustannuksiltaan parhaaksi vaihtoehdoksi osoittautui kuonan käsittely omalla biopolttoaineiden välivarastolla sekä käsitellyn pohjakuonan hyödyntäminen välivaraston pohjarakenteissa.
Resumo:
Waste has been incinerated for energy utilization for more than a hundred years, but the harmful emissions emitted from the incineration plants did not begin to cause concern until the 1980s. Many plants were shutdown and the waste incineration plant in Kyläsaari Helsinki was one of them. In later years, new landfill regulations have increased the interest in waste incineration. During the last year, four new plants were taken into operation in Finland, Westenergy in Vaasa among them. The presence of dust has been observed indoors at Westenergy waste incineration plant. Dust is defined as particles with a diameter above 10 μm, while fine particles have a diameter smaller than 2.5 μm, ultrafine under 0.1 μm and nanoparticles under 0.05 μm. In recent years, the focus of particle health research has been changed to investigate smaller particles. Ultrafine particles have been found to be more detrimental to health than larger particles. Limit values regulating the concentrations of ultrafine particles have not been determined yet. The objective of this thesis was to investigate dust and particles present inside the Westenergy waste incineration facility. The task was to investigate the potential pollutant sources and to give recommendations of how to minimize the presence of dust and particles in the power plant. The total particle number concentrations and size distributions where measured at 15 points inside the plant with an Engine Exhaust Particle Sizer (EEPS) Spectrometer. The measured particles were mainly in the ultrafine size range. Dust was only visually investigated, since the main purpose was to follow the dust accumulation. The measurement points inside the incineration plant were chosen according to investigate exposure to visitors and workers. At some points probable leakage of emissions were investigated. The measurements were carried out during approximately one month in March–April 2013. The results of the measurements showed that elevated levels of dust and particles are present in the indoor air at the waste incineration plant. The cleanest air was found in the control room, warehouse and office. The most polluted air was near the sources that were investigated due to possible leakage and in the bottom ash hall. However, the concentrations were near measured background concentrations in European cities and no leakage could be detected. The high concentrations were assumed to be a result of a lot of dust and particles present on surfaces that had not been cleaned in a while. The main source of the dust and particles present inside the waste incineration plant was thought to be particles and dust from the outside air. Other activities in the area around the waste incineration facility are ground work activities, stone crushing and traffic, which probably are sources of particle formation. Filtration of the outside air prior entering the facility would probably save personnel and visitors from nuisance and save in cleaning and maintenance costs.
Resumo:
Vantaan Energia rakentaa ympäristövaatimukset täyttävän jätevoimalan Itä-Vantaan Långmossebergeniin. Jätevoimalassa tullaan käyttämään polttoaineena kierrätykseen kelpaamatonta syntypaikkalajiteltua yhdyskuntajätettä sekä maakaasua. Helsingin seudun ympäristöpalvelut -kuntayhtymä HSY tulee toimittamaan noin 80 % vuosittaisesta jätepolttoaineesta. Tässä työssä on esitetty toimintamalli HSY:n jätteenpolton materiaalivirtojen hallitsemiseksi. Toimintamallin tarkoituksena on antaa ohjeistus jätteiden materiaalivirtojen käsittelymenetelmistä ennen jätteenpolttolaitosta. Lisäksi toimintamallin tarkoituksena on saada vähennettyä pohjakuonan määrää. Toimintamalli sisältää ohjeistuksen kotitalouksien sekajätteen, pienjäteasemien sekajätteen, sekalaisen rakennus- ja purkujätteen sekä kaupan- ja teollisuuden jätteiden käsittelytavoista. Jätevirtojen koostumusta on selvitetty kirjallisuudesta löytyvien tietojen perusteella ja tietoja on täydennetty kesällä 2013 suoritetun lajittelututkimuksen tiedoilla. Tutkimuksen tuloksista selvisi, että pienjäteasemien sekajätteiden lajittelua tehostamalla HSY:llä pystytään tekemään merkittäviä taloudellisia säästöjä. Tutkimuksessa selvisi, että kipsilevy olisi kannattavinta kerätä omalle lavalleen pienjäteasemilla. Sekalaisen rakennus- ja purkujätteen osalta todettiin, että sitä ei kannata ohjata suoraan jätevoimalalle poltettavaksi, eikä sitä voida sijoittaa käsittelemättömänä kaatopaikalle vuoden 2020 jälkeen. Tästä syystä työssä on ehdotettu, että sekalainen rakennus- ja purkujäte ohjattaisiin lajittelulaitokselle käsiteltäväksi ennen sen loppusijoittamista. Tutkimuksen tulosten perusteella voidaan myös todeta, että toimintamallia noudattamalla, pohjakuonan määrää on mahdollista vähentää lähes puolella alkuperäisestä arviosta.
Resumo:
This study is done to examine waste power plant’s optimal processing chain and it is important to consider from several points of view on why one option is better than the other. This is to insure that the right decision is made. Incineration of waste has devel-oped to be one decent option for waste disposal. There are several legislation matters and technical options to consider when starting up a waste power plant. From the tech-niques pretreatment, burner and flue gas cleaning are the biggest ones to consider. The treatment of incineration residues is important since it can be very harmful for the envi-ronment. The actual energy production from waste is not highly efficient and there are several harmful compounds emitted. Recycling of waste before incineration is not very typical and there are not many recycling options for materials that cannot be easily re-cycled to same product. Life cycle assessment is a good option for studying the envi-ronmental effect of the system. It has four phases that are part of the iterative study process. In this study the case environment is a waste power plant. The modeling of the plant is done with GaBi 6 software and the scope is from gate-to-grave. There are three different scenarios, from which the first and second are compared to each other to reach conclusions. Zero scenario is part of the study to demonstrate situation without the power plant. The power plant in this study is recycling some materials in scenario one and in scenario two even more materials and utilize the bottom ash more ways than one. The model has the substitutive processes for the materials when they are not recycled in the plant. The global warming potential results show that scenario one is the best option. The variable costs that have been considered tell the same result. The conclusion is that the waste power plant should not recycle more and utilize bottom ash in a number of ways. The area is not ready for that kind of utilization and production from recycled materials.
Resumo:
Energiantuotannossa syntyvä tuhka voi olla laadultaan hyvin vaihtelevaa ja laadunvaihtelulle on haastavaa löytää yksiselitteistä syy-seuraussuhdetta. Ympäristönsuojelulainsäädäntö ja taloudelliset intressit ohjaavat tuhkantuottajia etsimään tuhkalle sopivia hyötykäyttökohteita, ja sen vuoksi tuhkan laatuun ja hyötykäyttökelpoisuuteen vaikuttavia tekijöitä on tarpeen selvittää. Tässä diplomityössä on tutkittu pienissä, alle 50 MW:n polttolaitoksissa syntyvää tuhkaa. Tavoitteena oli selvittää, kuinka tuhkan hyötykäyttökelpoisuuteen voidaan vaikuttaa. Tutkimuksen kohteena oli polttoainekoostumuksen, poltto-olosuhteiden ja tuhkan jälkikäsittelyn vaikutus tuhkassa olevien haitta-aineiden pitoisuuksiin ja liukoisuuksin. Työhön sisältyi myös aiemmin tehtyjen tuhka-analyysien tarkastelu sekä tuhkakokeet kahdella kohderyhmään kuuluvalla laitoksella. Työssä todettiin lentotuhkan haitta-ainepitoisuuksien ja -liukoisuuksien olevan keskimäärin korkeampia kuin pohjatuhkan vastaavien, ja että tyypillisesti arinakattilan tuhkien haitta-aineet ylittävät useammin hyötykäyttökelpoisuuden raja-arvoja kuin kuplaleijupetikattilan tuhkien. Lisäksi havaittiin metsätähdehaketuhkan kelpaavan useammin hyötykäyttöön kuin rankahaketuhkan.
Resumo:
The objectives of this master’s thesis were to understand the importance of bubbling fluidized bed (BFB) conditions and to find out how digital image processing and acoustic emission technology can help in monitoring the bed quality. An acoustic emission (AE) measurement system and a bottom ash camera system were evaluated in acquiring information about the bed conditions. The theory part of the study describes the fundamentals of BFB boiler and evaluates the characteristics of bubbling bed. Causes and effects of bed material coarsening are explained. The ways and methods to monitor the behaviour of BFB are determined. The study introduces the operating principles of AE technology and digital image processing. The empirical part of the study describes an experimental arrangement and results of a case study at an industrial BFB boiler. Sand consumption of the boiler was reduced by optimization of bottom ash handling and sand feeding. Furthermore, data from the AE measurement system and the bottom ash camera system was collected. The feasibility of these two systems was evaluated. The particle size of bottom ash and the changes in particle size distribution were monitored during the test period. Neither of the systems evaluated was ready to serve in bed quality control accurately or fast enough. Particle size distributions according to the bottom ash camera did not correspond to the results of manual sieving. Comprehensive interpretation of the collected AE data requires much experience. Both technologies do have potential and with more research and development they may enable acquiring reliable and real-time information about the bed conditions. This information could help to maintain disturbance-free combustion process and to optimize bottom ash handling system.
Resumo:
For proper management of wastes and their possible recycling as raw materials, complete characterization of the materials is necessary to evaluate the main scientific aspects and potential applications. The current paper presents a detailed scientific study of different Brazilian sugar cane bagasse ashes from the cogeneration industry as alternative cementing materials (active addition) for cement manufacture. The results show that the ashes from the industrial process (filter and bottom ones) present different chemical and mineralogical compositions and pozzolanic properties as well. As a consequence of its nature, the kinetic rate constant (K) states that the pozzolanic activity is null for the bottom ash and very low for the filter ash with respect to a sugar cane bagasse ash obtained in the laboratory under controlled burning conditions (reference). The scarce pozzolanic activity showed by ashes could be related to a possible contamination of bagasse wastes (with soils) before their use as alternative combustibles. For this reason, an optimization process for these wastes is advisable, if the ashes are to be used as pozzolans. (C) 2011 Elsevier Ltd. All rights reserved.
Resumo:
Este trabalho tem como objetivo verificar o comportamento mecânico e físico de pozolanas artifíciais estabilizadas química e granulometricamente, curadas por dois processos de cura denominados de : autoclave(ATC), que utiliza temperaturas na faixa de 149 a 188°C e câmara à temperatura constante(CTC) que utiliza uma temperatura de ± 21°C. Também fez-se análises estatísticas com a finalidade de se determinar o efeito da energia de moldagem, temperatura e tempo de cura sobre os resultados dos ensaios, para cada processo de cura, além de se determinar modelos matemáticos para previsão de resultados de resistência através de regressões múltiplas e simples. As pozolanas artificiais empregadas foram as cinzas volante e pesada da Usina de Candiota, as quais foram estabilizadas com cal dolomítica hidratada e areia do Rio Guaíba. Os ensaios de resistência à compressão simples , absorção e perda de massa basearam-se nas normas da ABNT e DNER e para os estudos de análise estatística, fez-se anteriormente aos ensaios, dois planejamentos experimentais denominados de Split-Splot e Quadrado Latino, que foram utilizados nos processos de autoclavagem e câmara à temperatura constante, representativamente. Os Corpos-de-Prova curados na câmara à temperatura constante, até os 28 dias de cura, apresentaram resultados de resistências inferiores aqueles curados pelo processo de autoclave. Aos 60 dias de cura suas resistências ficaram na faixa dos valores de Corpos-de-Provas curados pela autoclave nas temperaturas de 149 a 188°C, excessão feita na mistura utilizando areia, onde em todos os períodos de cura estudados,os valores de resistência dos Corpos-de-Prova curados pelo câmara à temperatura constante foram inferiores. A proporção da quantidade de cal e cinza na mistura, bem como o valor da superfície específica da cinza influenciam nos resultados de ensaios, independentemente da variação dos fatores principais. Em termos de análise estatística verificou-se que a energia de moldagem e o tempo de cura são os fatores que apresentam os maiores efeitos sobre os resultados da resistência, para os processos de cura ATC e CTC, respectivamente.