Effects of medium supplementation and pH control on lactic acid production from brewer`s spent grain

A cellulose pulp obtained by chemical pre-treatment of brewer`s spent grain was saccharified by a commercial cellulase preparation and the produced hydrolysate (50 g/l glucose) was fermented to lactic acid by Lactobacillus delbrueckii. The effects of pH control and nutrient supplementation of the hydrolysate on fermentation performance were investigated. Addition of 5g/l yeast extract enhanced the lactic acid volumetric productivity that attained 0.53 g/l h, value 18% higher than that obtained from non-supplemented hydrolysate. Addition of the MRS broth medium components (except the carbon source) was still better, providing a productivity of 0.79 g/l h. In all the cases, the lactic acid yield factor was of 0.7 g/g glucose consumed, but the fermentations stopped after 24 h due to the pH drop from 6.0 to 4.2, resulting in large amounts of residual glucose (38-41 g/l). Fermentation runs pH-controlled at 6.0 gave better results than those where the initial pH was not further controlled. The best result, 35.54 g/l lactic acid (0.99 g/g glucose consumed) was obtained during the pH-controlled fermentation of hydrolysate medium supplemented with MRS components. The volumetric productivity at the end of this fermentation was 0.59 g/l h, with a maximum of 0.82 g/l h during the first 12 h. (c) 2008 Elsevier B.V. All rights reserved.

Evaluation of encapsulation techniques of probiotics for yoghurt

The health benefits provided by probiotic bacteria have led to their increasing use in fermented and other dairy products. However, their viability in these products is low. Encapsulation has been investigated to protect the bacteria in the product's environment and improve their survival. There are two common encapsulation techniques, namely extrusion and emulsion, to encapsulate the probiotics for their use in the fermented and other dairy products. This review evaluates the merits and limitations of these two techniques, and also discusses the supporting materials and special treatments used in encapsulation processes. (C) 2003 Elsevier Science Ltd. All rights reserved.

Retention of short chain fatty acids under drying and storage conditions

Cheese whey permeate was used as a substrate for the fermentation of Propionibacterium freudenreichi PS1 for the production of short chain fatty acids, components of the bio-aroma of Swiss cheese. The liquid bio-aroma was encapsulated by spray drying under different conditions of air inlet temperature and feed rate. A study was carried out on the stability of the bio-aroma during storage in laminated packages at 30 °C for 96 days using the product showing the greatest retention of acetic and propionic acids. The results showed that the best drying conditions were an air entrance temperature of 180 °C and a feed rate of 24 g/min resulting in particles with a smooth surface and few invaginations and micro-fissures. However, 72% of the acetic acid and 80% of the propionic acid were lost during storage showing that the wall material used was inadequate to guarantee product stability.

Proceedings of the Twelfth Annual Biochemical Engineering Symposium

This work presents the proceedings of the twelfth symposium which was held at Kansas State University on April 24, 1982. Since a number of the contributions will be published in detail elsewhere, only brief reports are included here. Some of the reports describe current progress with respect to ongoing projects. Requests for further information should be directed to Dr. Peter Reilly at Iowa State University, Dr. V. G. Murphy at Colorado State University, Dr. Rakesh Bajpai at University of Missouri, Dr. Ed Clausen at University of Arkansas, Dr. L. T. Fan and Dr. L. E. Erickson at Kansas State University. ContentsA Kinetic Analysis of Oleaginous Yeast Fermentation by Candida curvata on Whey Permeate, B.D. Brown and K.H. Hsu, Iowa State University Kinetics of Biofouling in Simulated Water Distribution Systems Using CSTR, T.M. Prakash, University of Missouri Kinetics of Gas Production by C. acetobutylicum, Michael Doremus, Colorado State University Large Scale Production of Methane from Agricultural Residues, O.P. Doyle, G.C. Magruder, E.C. Clausen, and J.L. Gaddy, University of Arkansas The Optimal Process Design for Enzymatic Hydrolysis of Wheat Straw, M.M Gharpuray and L.T. Fan, Kansas State University Extractive Butanol Fermentation, Michael Sierks, Colorado State University Yields Associated with Ethyl Alcohol Production, M.D. Oner, Kansas State University Estimation of Growth Yield and Maintenance Parameters for Microbial Growth on Corn Dust, B.O. Solomon, Kansas State University Milling of Ensiled Corn, Andrzej Neryng, Iowa State University Protein Extraction from Alfalfa, Ravidranath Joshi, Colorado State University Analysis of Disaccharides by Capillary Gas Chromatography, Z.L. Nikolov, Iowa State University Characterization of High Viscosity Fermentations in Tower Fermentors, S.A. Patel and C.H. Lee, Kansas State University Utilization of Sugars in Sorghum Molasses by Clostridium acetobutylicum B. Hong, K.C. Shin, and L.T. Fan, Kansas State University

Isomérisation du lactose en lactulose en solution modèle de lactose et dans du perméat de lactosérum par électro-activation supportée par échange ionique sur résine

L’isomérisation alcaline du lactose en lactulose a été effectuée électro-chimiquement à l’aide d’un réacteur d’électro-activation en combinaison avec des résines échangeuses d’anions de polystyrène de trois types; à savoir Lewatit VP-OC-1065 faible-acide, Lewatit MP-64 moyenne-acide et Lewatit Monoplus M500 forte-acide. Les paramètres opératoires qui ont fait l’objet de cette étude ont été étudiés sur trois blocs expérimentaux pour optimiser le système. Dans le Premier bloc, les paramètres étudiés sont : (1) ratio lactose-5%(p/v) : résine échangeuse d’anions (1:0.5, 1:1 et 1:2), (2) intensité du champ électrique : 50 mA, 100 mA et 200 mA et (3) type de résines : faible, moyenne et forte. Dans le Deuxième bloc, les paramètres mis à l’étude comprenaient : (1) l’intensité du champ électrique : 300 mA, 450 mA et 550 mA, (2) le débit de la solution traitée : 25 ml / min, 50 ml/ min et 100 ml/min et (3) la surface active de la membrane adjacente au compartiment cathodique : 0.78 cm2, 7.06 cm2 et 18.1 cm2. Le Troisième bloc expérimental a été effectué sur la base de la distance entre la membrane et l’électrode : 3.1 cm, 5.6 cm et 9 cm. Le même modèle expérimental a était également réalisé avec du perméat du lactosérum d’une concentration de 7% (p/v). Les résultats obtenus ont révélé que le meilleur rendement de l’isomérisation du lactose en lactulose était obtenu après 30 minutes d’électroactivation en utilisant une solution modèle de lactose-5% avec une valeur d’environ 20.1%. Les conditions opératoires qui ont permis d’avoir ce taux de conversion sont une intensité du courant de 550 mA, un débit de la solution de 25 ml/min, une surface active de la membrane de 7.06 cm2 et une distance de 9 cm entre la cathode et la membrane qui lui y est adjacente. En utilisant le perméat de lactosérum-7%, un taux de conversion de lactose en lactulose de 8.34% a était obtenu avec une intensité du courant de 200 mA, un débit de 120 ml/min, une surface active de de 18.1cm2 et une distance de 9 cm entre la membrane et l’électrode dans le compartiment cathodique. Les analyses de variance ont indiqué un effet catalytique significatif du type de la résine. En effet, la résine-forte a permis d’avoir les plus hauts rendements de la réaction d’isomérisation par électro-activation. La résistance électrique globale du système d’électroactivation dépendait de la valeur de l’intensité du courant. Le produit final était d’une grande pureté, car il ne présentait que quelques traces de galactose (< 4%).

Poly(3-hydroxybutyrate) production from whey using recombinant Escherichia coli

Recombinant Escherichia coli strains harboring the genes from Alcaligenes eutrophus for polyhydroxyalkanoate biosynthesis were constructed and compared for their ability to synthesize poly(3-hydroxybutyrate) in a defined medium with whey as the sole carbon source. The highest PHB concentration and PHB content obtained were 5.2 g/L and 81% of dry cell weight, respectively.

Effect of physico-chemical conditions and operating parameters on flux and retention of different components in ultrafiltration and nanofiltration fractionation of sweet whey

Tässä väitöstutkimuksessa tutkittiin fysikaaliskemiallisten olosuhteiden ja toimintaparametrien vaikutusta juustoheran fraktiointiin. Kirjallisuusosassa on käsitelty heran ympäristövaikutusta, heran hyödyntämistä ja heran käsittelyä kalvotekniikalla. Kokeellinen osa on jaettu kahteen osaan, joista ensimmäinen käsittelee ultrasuodatusta ja toinen nanosuodatusta juustoheran fraktioinnissa. Ultrasuodatuskalvon valinta tehtiin perustuen kalvon cut-off lukuun, joka oli määritetty polyetyleeniglykoliliuoksilla olosuhteissa, joissa konsentraatiopolariosaatioei häiritse mittausta. Kriittisen vuon konseptia käytettiin sopivan proteiinikonsentraation löytämiseksi ultrasuodatuskokeisiin, koska heraproteiinit ovat tunnetusti kalvoa likaavia aineita. Ultrasuodatuskokeissa tutkittiin heran eri komponenttien suodattumista kalvon läpi ja siihen vaikuttavia ominaisuuksia. Herapermeaattien peptidifraktiot analysoitiin kokoekskluusiokromatografialla ja MALDI-TOF massaspektrometrillä. Kokeissa käytettävien nanosuodatuskalvojen keskimääräinen huokoskoko analysoitiin neutraaleilla liukoisilla aineilla ja zeta-potentiaalit virtauspotentiaalimittauksilla. Aminohappoja käytettiin malliaineina tutkittaessa huokoskoon ja varauksen merkitystä erotuksessa. Aminohappojen retentioon vaikuttivat pH ja liuoksen ionivahvuus sekä molekyylien väliset vuorovaikutukset. Heran ultrasuodatuksessa tuotettu permeaatti, joka sisälsi pieniä peptidejä, laktoosia ja suoloja, nanosuodatettiin happamassa ja emäksisessä pH:ssa. Emäksisissä oloissa tehdyssä nanosuodatuksessa foulaantumista tapahtui vähemmän ja permeaattivuo oli parempi. Emäksisissä oloissa myös selektiivisyys laktoosin erotuksessa peptideistä oli parempi verrattuna selektiivisyyteen happamissa oloissa.

Selective separation of the major whey proteins using ion exchange membranes

Synthetic microporous membranes with functional groups covalently attached were used to selectively separate beta-lactoglobulin, BSA, and alpha-lactalbumin from rennet whey. The selectivity and membrane performance of strong (quaternary ammonium) and weak (diethylamine) ion-exchange membranes were studied using breakthrough curves, measurement of binding capacity, and protein composition of the elution fraction to determine the binding behavior of each membrane. When the weak and strong anion exchange membranes were saturated with whey, they were both selective primarily for beta-lactoglobulin with less than 1% of the eluate consisting of alpha-lactalbumin or BSA. The binding capacity of a pure alpha-lactoglobulin solution was in excess of 1.5 mg/cm(2) of membrane. This binding capacity was reduced to approximately 1.2 mg/cm(2) when using a rennet whey solution (pH 6.4). This reduction in protein binding capacity can be explained by both the competitive effects of other whey proteins and the effect of ions present in whey. Using binary solution breakthrough curves and rennet whey breakthrough curves, it was shown that alpha-lactalbumin and BSA were displaced from the strong and weak anion exchange membranes by beta-lactoglobulin. Finally, the effect of ionic strength on the binding capacity of individual proteins for each membrane was determined by comparing model protein solutions in milk permeate (pH 6.4) and a 10 mM sodium phosphate buffer (pH 6.4). Binding capacities of beta-lactoglobulin, alpha-lactalbumin, and BSA in milk permeate were reduced by as much as 50%. This reduction in capacity coupled with the low binding capacity of current ion exchange membranes are 2 serious considerations for selectively separating complex and concentrated protein solutions.

Separation of oligosaccharides from caprine milk whey, prior to prebiotic evaluation

Milk oligosaccharides are believed to have beneficial biological properties. Caprine milk has a relatively high concentration of oligosaccharides in comparison to other ruminant milks and has the closest oligosaccharide profile to human milk. The first stage in recovering oligosaccharides from caprine milk whey, a by-product of cheese making, was accomplished by ultrafiltration to remove proteins and fat globules, leaving more than 97% of the initial carbohydrates, mainly lactose, in the permeate. The ultrafiltered permeate was further processed using a 1 kDa ‘tight’ ultrafiltration membrane, which retained less than 7% of the remaining lactose. The final retentate was fractionated by preparative scale molecular size exclusion chromatography, to yield 28 fractions, of which oligosaccharide-rich fractions were detected somewhere between fractions 9/10 to 16/17, suitable for functionality and gut health promotion testing. All fractions were evaluated for their oligosaccharide and carbohydrate profiles using three complementary analytical methods.

Whey And Soy Protein Supplements Changes Body Composition In Patients With Crohn's Disease Undergoing Azathioprine And Anti-tnf-alpha Therapy.

Crohn´s disease (CD) is a chronic transmural inflammation of the gastrointestinal tract of unknown cause. Malnutrition associated with active CD has been reduced although obesity has increased. Dietary strategies such as those with high-protein have been proposed to reduce body fat. This study compares the effects of two supplements on the nutritional status of CD patients. 68 CD patients were randomized in two groups: whey protein group (WP) and soy protein group (SP). Using bioimpedance analysis, anthropometry and albumin and pre-albumin dosages the nutritional status was measured before starting the intervention and after 8 and 16 weeks. The disease activity was determined by Crohn's Disease Activity Index and serum C-reactive protein dosage and dietary intake by 24h dietary recalls. Forty-one patients concluded the study and both supplements changed body composition similarly. Triceps skin fold thickness (p< 0.001) and body fat percentage (p=0.001) decreased, whereas mid-arm muscle circumference (p=0.004), corrected arm muscle area (p=0.005) and body lean percentage (p=0.001) increased. For Crohn's disease patients undergoing anti TNF-alpha and azatioprine therapies, supplementation with whey and soy proteins changes body composition through reduction of body fat and thus contributes to control inflammation.

Optimal fermentation conditions for maximizing the ethanol production by Kluyveromyces fragilis from cheese whey powder

Cheese whey powder (CWP) is an attractive raw material for ethanol production since it is a dried and concentrated form of CW and contains lactose in addition to nitrogen, phosphate and other essential nutrients. In the present work, deproteinized CWP was utilized as fermentation medium for ethanol production by Kluyveromyces fragilis. The individual and combined effects of initial lactose concentration (50-150 kg m(-3)), temperature (25-35 degrees C) and inoculum concentration (1-3 kg m(-3)) were investigated through a 2(3) full-factorial central composite design, and the optimal conditions for maximizing the ethanol production were determined. According to the statistical analysis, in the studied range of values, only the initial lactose concentration had a significant effect on ethanol production, resulting in higher product formation as the initial substrate concentration was increased. Assays with initial lactose concentration varying from 150 to 250 kg m(-3) were thus performed and revealed that the use of 200 kg m(-3) initial lactose concentration, inoculum concentration of 1 kg m(-3) and temperature of 35 degrees C were the best conditions for maximizing the ethanol production from CWP solution. Under these conditions, 80.95 kg m(-3) of ethanol was obtained after 44 h of fermentation. (C) 2011 Elsevier Ltd. All rights reserved.

Comparative study of the biochemical changes and volatile compound formations during the production of novel whey-based kefir beverages and traditional milk kefir

Cheese whey (CW) and deproteinised cheese whey (DCW) were investigated for their suitability as novel substrates for the production of kefir-like beverages. Lactose consumption, ethanol production, as well as organic acids and volatile compounds formation, were determined during CW and DCW fermentation by kefir grains and compared with values obtained during the production of traditional milk kefir. The results showed that kefir grains were able to utilise lactose from CW and DCW and produce similar amounts of ethanol (7.8-8.3 g/l), lactic acid (5.0 g/l) and acetic acid (0.7 g/l) to those obtained during milk fermentation. In addition, the concentration of higher alcohols (2-methyl-1-butanol, 3-methyl-1-butanol, 1-hexanol, 2-methyl-1-propanol, and 1-propanol), ester (ethyl acetate) and aldehyde (acetaldehyde) in cheese whey-based kefir and milk kefir beverages were also produced in similar amounts. Cheese whey and deproteinised cheese whey may therefore serve as substrates for the production of kefir-like beverages similar to milk kefir. (C) 2010 Elsevier Ltd. All rights reserved.

Chemical composition and sensory analysis of cheese whey-based beverages using kefir grains as starter culture

P>The aim of the present work was to evaluate the use of the kefir grains as a starter culture for tradicional milk kefir beverage and for cheese whey-based beverages production. Fermentation was performed by inoculating kefir grains in milk (ML), cheese whey (CW) and deproteinised cheese whey (DCW). Erlenmeyers containing kefir grains and different substrates were statically incubated for 72 h at 25 degrees C. Lactose, ethanol, lactic acid, acetic acid, acetaldehyde, ethyl acetate, isoamyl alcohol, isobutanol, 1-propanol, isopentyl alcohol and 1-hexanol were identified and quantified by high-performance liquid chromatography and GC-FID. The results showed that kefir grains were able to utilise lactose in 60 h from ML and 72 h from CW and DCW and produce similar amounts of ethanol (similar to 12 g L-1), lactic acid (similar to 6 g L-1) and acetic acid (similar to 1.5 g L-1) to those obtained during milk fermentation. Based on the chemical characteristics and acceptance in the sensory analysis, the kefir grains showed potential to be used for developing cheese whey-based beverages.

Effects of Feed Time, Organic Loading and Shock Loads in Anaerobic Whey Treatment by an AnSBBR with Circulation

The aim of this work was to investigate the effect of different feeding times (2, 4, and 6 h) and organic loading rates (3, 6 and 12 gCOD l(-1) day(-1)) on the performance of an anaerobic sequencing batch reactor containing immobilized biomass, as well as to verify the minimum amount of alkalinity that can be added to the influent. The reactor, in which mixing was achieved by recirculation of the liquid phase, was maintained at 30 +/- 1A degrees C, possessed 2.5 l reactional volume and treated 1.5 l cheese whey in 8-h cycles. Results showed that the effect of feeding time on reactor performance was more pronounced at higher values of organic loading rates (OLR). During operation at an OLR of 3 gCOD l(-1) day(-1), change in feeding time did not affect efficiency of organic matter removal from the reactor. At an OLR of 6 gCOD l(-1) day(-1), reactor efficiency improved in relation to the lower loading rate and tended to drop at longer feeding times. At an OLR of 12 gCOD l(-1) day(-1) the reactor showed to depend more on feeding time; higher feeding times resulted in a decrease in reactor efficiency. Under all conditions shock loads of 24 gCOD l(-1) day(-1) caused an increase in acids concentration in the effluent. However, despite this increase, the reactor regained stability readily and alkalinity supplied to the influent showed to be sufficient to maintain pH close to neutral during operation. Regardless of applied OLR, operation with feeding time of 2 h was which provided improved stability and rendered the process less susceptible to shock loads.

MULTIVARIATE STATISTICAL METHOD IN OPTIMIZATION OF PROTEIN EXTRACTION FROM SOYBEAN FLOUR WITH DAIRY WHEY

The aim objective of this project was to evaluate the protein extraction of soybean flour in dairy whey, by the multivariate statistical method with 2(3) experiments. Influence of three variables were considered: temperature, pH and percentage of sodium chloride against the process specific variable ( percentage of protein extraction). It was observed that, during the protein extraction against time and temperature, the treatments at 80 degrees C for 2h presented great values of total protein (5.99%). The increasing for the percentage of protein extraction was major according to the heating time. Therefore, the maximum point from the function that represents the protein extraction was analysed by factorial experiment 2(3). By the results, it was noted that all the variables were important to extraction. After the statistical analyses, was observed that the parameters as pH, temperature, and percentage of sodium chloride, did not sufficient for the extraction process, since did not possible to obtain the inflection point from mathematical function, however, by the other hand, the mathematical model was significant, as well as, predictive.