Durability of monumental stones treated with siloxane-based water repellents

The thesis investigates the effect of siloxane-based water repellents on the durability of monumental stones. Laspra, a micritic limestone typical for the Spanish region of Asturias, and Repedea, an oolitic limestone from Moldavia, Romania were selected for the present study, due to their regional / national significance and level of usage. As for the siloxane-based water repellents, three worldwide used products, namely Lotexan-N, Silres® BS 290 and Tegosivin HL 100 and a newly synthesized nanocomposite material, TMSPMA, obtained starting from the 3(trimethoxysilyl)propyl methacrylate as a precursor were investigated. The limestones and the water repellents were thoroughly characterized using specific techniques. The coating of the two monumental stones with the mentioned products and the investigation of coating efficiency yielded to the conclusion that all treatments induce good water repellent properties. The treated limestones were afterwards submitted to different artificially accelerated ageing tests – resistance against UV irradiation, resistance to salt mist action and resistance to SO2 action in the presence of humidity –, the results being analyzed according to standardized evaluation methods. The durability of the treated stones was proved to depend on both stone characteristics and water repellent chemical structure. All four water repellents induced a good protection against UV irradiation, no significant differences among them being noticed. As far as the resistance to salt mist action is concerned, the product that afforded the best results when applied on Laspra was TMSPMA, and on Repedea, Silres® BS 290 or / and TMSPMA showed the highest efficiency. The best resistance to SO2 action in the presence of humidity was conferred by Tegosivin HL 100 and TMSPMA when applied on Laspra, while Silres® BS 290 and TMSPMA afforded better results in the case of Repedea.

Wettability, polarity and water absorption of Quercus ilex leaves: effect of leaf side and age

Plant trichomes play important protective functions and may have a major influence on leaf surface wettability. With the aim of gaining insight into trichome structure, composition and function in relation to water-plant surface interactions, we analyzed the adaxial and abaxial leaf surface of Quercus ilex L. (holm oak) as model. By measuring the leaf water potential 24 h after the deposition of water drops on to abaxial and adaxial surfaces, evidence for water penetration through the upper leaf side was gained in young and mature leaves. The structure and chemical composition of the abaxial (always present) and adaxial (occurring only in young leaves) trichomes were analyzed by various microscopic and analytical procedures. The adaxial surfaces were wettable and had a high degree of water drop adhesion in contrast to the highly unwettable and water repellent abaxial holm oak leaf sides. The surface free energy, polarity and solubility parameter decreased with leaf age, with generally higher values determined for the abaxial sides. All holm oak leaf trichomes were covered with a cuticle. The abaxial trichomes were composed of 8% soluble waxes, 49% cutin, and 43% polysaccharides. For the adaxial side, it is concluded that trichomes and the scars after trichome shedding contribute to water uptake, while the abaxial leaf side is highly hydrophobic due to its high degree of pubescence and different trichome structure, composition and density. Results are interpreted in terms of water-plant surface interactions, plant surface physical-chemistry, and plant ecophysiology.

Effect of surface-applied treatments on the above-ground performance of simulated timber joinery

We examined the effect of surface-applied treatments on the above-ground decay resistance of the tenon of mortice-and-tenon timber joints designed to simulate joinery that is exposed to the weather. Joints made from untreated radiata pine, Douglas-fir, brush box, spotted gum and copper-chrome-arsenic (CCA) treated radiata pine were exposed to the weather for 9 y on above-ground racks at five sites throughout eastern Australia. Results indicate (1) a poorly maintained external paint film generally accelerated decay, (2) a brush coat of water-repellent preservative inside the joints often extended serviceability (in some cases by a factor of up to seven times that of untreated joints) and (3) the level of protection provided by a coat of primer applied inside the joint varied and in most cases was not as effective as the water-repellent preservative treatment.

Quantifying surfactant interaction effects on soil moisture and turf quality

Soil water repellency occurs widely in horticultural and agricultural soils when very dry. The gradual accumulation and breakdown of surface organic matter over time produces wax-like organic acids, which coat soil particles preventing uniform entry of water into the soil. Water repellency is usually managed by regular surfactant applications. Surfactants, literally, are surface active agents (SURFace ACTive AgeNTS). Their mode of action is to reduce the surface tension of water, allowing it to penetrate and wet the soil more easily and completely. This practice improves water use efficiency (by requiring less water to wet the soil and by capturing rainfall and irrigation more effectively and rapidly). It also reduces nutrient losses through run-off erosion or leaching. These nutrients have the potential to pollute the surrounding environment and water courses. This project investigated potential improvements to standard practices (product combination and scheduling) for surfactant use to overcome localised dry spots on water repellent soils and thus improve turf quality and water use efficiency. Weather conditions for the duration of the trial prevented the identification of improved practices in terms of combination and scheduling. However, the findings support previous research that the use of soil surfactants decreased the time for water to infiltrate dry soil samples taken from a previously severely hydrophobic site. Data will be continually collected from this trial site on a private contractual basis, with the hope that improvements to standard practices will be observed during the drier winter months when moisture availability is a limiting factor for turfgrass growth and quality.

In vitro infection of sheep lice (Bovicola ovis Schrank) by Steinernematid and Heterorhabditid nematodes.

Control of sheep lice with conventional pesticides can be compromised by difficulty in contacting lice in the dense water repellent fleeces of sheep, particularly when sheep have not been recently shorn. Entomopathogenic nematodes (ENs) are motile and are able to actively seek out insect hosts. They have particular advantages for the control of pests in cryptic habitats, such as the fleeces of sheep and avoid many of the problems frequently associated with chemical controls. This study investigated whether ENs were able infect and kill Bovicola ovis and compared the effectiveness of different species at different temperatures and when applied to wool. Four species of nematodes, Steinernema carpocapsae, Steinernema riobrave, Steinernema feltiae and Heterorhabditis bacteriophora were tested. All were shown to infect and kill lice in Petri dish assays at 30C. At 35C, the percent infection for S. carpocapsae and S. riobrave was significantly higher than for the other two species and percent infection by S. feltiae was significantly greater than for H. bacteriophora (P<0.05). At 37C the percent mortality induced by S. riobrave was significantly greater than for S. carpocapsae (P<0.05). All species were able to locate and infect lice in wool when formulated in water with 8% Tween 80. In wool assays the percent lice infected with nematodes was significantly greater for S. riobrave than H.bacteriophora at 25C, but there were no other differences between species (P=0.05). S. carpocapsae, S. riobrave and S. feltiae caused significantly higher lice mortality than H. bacteriophora at both 25 and 35C in wool assays, but mortality induced by the three steinernematid species did not differ significantly (P>0.05). It is concluded that of the ENs studied S. riobrave is likely to be most effective against B. ovis when applied to live sheep because of its greater tolerance to high temperatures and 'cruiser' foraging strategy .

Influence Of Different Amount Of Au On The Wetting Behavior Of Pdms Membrane

Polydimethylsiloxane (PDMS) has been widely used as a base material for bio-MEMS/NEMS devices. It is difficult for PDMS to transfer and spread aqueous solution as a kind of highly hydrophobic material. Therefore, surface modification is necessary for PDMS to make it hydrophilic. In this paper, a method of hydrophilization of PDMS surface is proposed. Gold is sputtered to the PDMS substrate by sputter coater in different average thicknesses. Relationship between the average thickness of gold on the PDMS substrate and the contact angle of the surface was studied. It was found that even gold of average thickness less than 1 nm can result in about 25 degrees change of contact angle. AFM is also used to get topographic information of PDMS surface coated with gold. Three cases are classified with different amount of Au: (1) Heterogeneous zone; (2) Transition zone; (3) Film zone. For heterogeneous zone, a simple model about heterogeneous phase wetting is put forward to interpret this phenomenon.

Physicochemical characteristics and droplet impact dynamics of superhydrophobic carbon nanotube arrays.

The physicochemical and droplet impact dynamics of superhydrophobic carbon nanotube arrays are investigated. These superhydrophobic arrays are fabricated simply by exposing the as-grown carbon nanotube arrays to a vacuum annealing treatment at a moderate temperature. This treatment, which allows a significant removal of oxygen adsorbates, leads to a dramatic change in wettability of the arrays, from mildly hydrophobic to superhydrophobic. Such change in wettability is also accompanied by a substantial change in surface charge and electrochemical properties. Here, the droplet impact dynamics are characterized in terms of critical Weber number, coefficient of restitution, spreading factor, and contact time. Based on these characteristics, it is found that superhydrophobic carbon nanotube arrays are among the best water-repellent surfaces ever reported. The results presented herein may pave a way for the utilization of superhydrophobic carbon nanotube arrays in numerous industrial and practical applications, including inkjet printing, direct injection engines, steam turbines, and microelectronic fabrication.

Super-hydrophobicity of silica nanoparticles modified with vinyl groups

Super-hydrophobic films with vinyl-modified silica nanoparticles (V-SiOx-NPs) were successfully prepared. The rough surface, which was composed of microstructures of disordered V-SiOx-NPs and nanostructures on the surface of V-SiOx-NPs, rather than the chemical composition devoted to the super-hydrophobicity of film. The relationship between contact angle and diameter of V-SiOx-NPs was then investigated. The sessile contact angles (CA) of films with 150-1600nm V-SiOx-NPs were around 166 regardless the diameter, while the film with 85 nm V-SiOx-NPs had the lowest CA of about 158. The packing manner of V-SiOx-NPs determined the air fraction on the surface and then the CA.

A general route to transform normal hydrophilic cloths into superhydrophobic surfaces

Herein, we describe a simple and inexpensive method for forming superhydrophobic cloths with the highest water contact angle of close to 180 degrees, in which normal commercial cloths serving as pristine materials are modified with suitable gold micro/nanostructures.

A composite polymer film with both superhydrophobicity and superoleophilicity

A composite film composed of porous polyurethane (PU) and polystyrene (PS) microspheres with both superhydrophobicity and superoleophilicity has been prepared. In this film, the dual-scale structure enhances both the hydrophobicity and oleophilicity of the surface material. The composite film with such an 'intelligent' wettability property can be utilized to separate oil and water systems efficiently.

Revestimentos compatíveis para alvenarias antigas sujeitas a ação severa da água

Uma das maiores causas de degradação dos revestimentos é a presença de sais solúveis, tanto nas zonas costeiras como nas zonas continentais. Estes sais podem ter origens distintas, tais como: humidade ascensional, nevoeiro salino, inundações ou ainda estarem presentes nos próprios materiais, como é o caso da utilização de areias mal lavadas. O local onde os sais cristalizam é dependente do tipo de transporte entre a alvenaria e o revestimento, assim como da severidade da envolvente ambiental (temperatura e humidade relativa). Com esta tese pretende-se desenvolver revestimentos de substituição compatíveis, eficazes e duráveis para alvenarias antigas sujeitas à ação severa da água (humidade ascensional através das fundações com elevada concentração de NaCl); desenvolver ensaios de envelhecimento acelerado baseados em ciclos de dissolução e cristalização que permitam simular a ação severa da água; perceber a influência de revestimentos com caraterísticas extremas de permeabilidade ao vapor de água aplicados nas duas faces do mesmo suporte (argamassas de cimento e resina versus argamassas de cal), e sujeitos à ação severa da água; perceber a influência de vários fatores, tais como : rasgos verticais contínuos executados no emboço e a utilização de hidrófugo no reboco no desempenho dos vários sistemas de revestimento desenvolvidos, quando sujeitos à ação severa da água;; utilizar a remoção eletrocinética de sais, em provetes simulando a influência da alvenaria e dos revestimentos, com o objetivo de reduzir a sua concentração de NaCl, para que no futuro possa ser aplicado de forma eficaz em paredes de edifícios antigos, enquanto ação de manutenção, e desta forma aumentar a durabilidade dos revestimentos. Para atingir os objetivos descritos, foram considerados: i) o desenvolvimento de provetes que permitam considerar os sistemas de revestimento desenvolvidos nesta tese e o suporte, e que simulem uma alvenaria revestida em ambas as faces, e com os quais seja possível a simulação da ação severa da água em laboratório e, ii) o desenvolvimento ciclos de dissolução e cristalização numa parede de grandes dimensões existente em laboratório, que permitam simular a ação severa da água em condições tão reais quanto possível. O objetivo final deste estudo é o desenvolvimento de um revestimento de substituição denominado “emboço ventilado” para paredes de edifícios antigos com revestimentos degradados devido à presença de humidade ascensional e sais solúveis. Pretende-se que este sistema de revestimento, composto por duas camadas de revestimento (camada base e reboco), seja compatível, durável e eficaz, e que funcione como um sistema de acumulação no qual os sais cristalizem na camada base do sistema de revestimento (executada com rasgos verticais) e não na alvenaria ou na camada exterior.

Modificação superficial do tecido 100% algodão tratado com plasma

The 100% cotton fabric (CO)* treated with plasma of methane CH4 has direct application in all areas that needs of aqueous solutions repellent material like coatings and uniforms applied biomedical, aeronautics, and automobile between others. 100% cotton fabric (CO) samples were treated by plasma with two differents atmosphere: Methane gas (CH4), treatment time was varied in 10 in 10 min. until 60 min., and mixture methane/argon (CH4/Ar), it was varied the proportion 1:9, 2:8, 3:7, 4:6, 5:5, 6:4, 7:3, 8:2 e 9:1, with treatment time of 30 minutes. In both, the fluxe was 5 sccm (second cubic centimeter), pressure 6 mbar, voltage 490 V and current 0,15A. The objective of work was measure the superficial tension of 100% CO then it treated with plasma, using contact angle measures of water and glycerol with the surface. The samples were tested after treatment, with 8 and 12 months to verify the superficial modification effects. It was verified an increase of hydrophobility with the Sessile drop values varied between 116,69º to 137,85º and it carried on after 12 months. The no treated samples shows contact angle equal 0º. OES analysis and Raman spectroscopy were accomplished. In the SEM analysis was verified oligomers. The plasma treatment is correct environmental, It turning greater than conventional treatments

Segurança no trabalho de preparo de calda no tanque de 2.000l do turbopulverizador com formulações líquidas de agrotóxicos registradas para a cultura de goiaba

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)