Procedure to characterize microroughness of optical thin films: application to ion-beam-sputtered vacuum-ultraviolet coatings

A method for characterizing the microroughness of samples in optical coating technology is developed. Measurements over different spatial-frequency ranges are composed into a single power spectral density (PSD) covering a large bandwidth. This is followed by the extraction of characteristic parameters through fitting of the PSD to a suitable combination of theoretical models. The method allows us to combine microroughness measurements performed with different techniques, and the fitting procedure can be adapted to any behavior of a combined PSD. The method has been applied to a set of ion-beam-sputtered fluoride vacuum-UV coatings with increasing number of alternative low- and high-index layers. Conclusions about roughness development and microstructural growth are drawn.

Vacuum-ultraviolet photochemically initiated modification of polystyrene surfaces: morphological changes and mechanistic investigations

Vacuum-ultraviolet (VUV) irradiation (kexc: 172 ± 12 nm) of polystyrene films in the presence of oxygen produced not only oxidatively functionalized surfaces, but generated also morphological changes. Whereas OH- and C=O-functionalized surfaces might be used for e.g. secondary functionalization, enhanced aggregation or printing, processes leading to morphological changes open new possibilities of microstructurization. Series of experiments made under different experimental conditions brought evidence of two different reaction pathways: introduction of OH- and C=O-groups at the polystyrene pathways is mainly due to the reaction of reactive oxygen species (hydroxyl radicals, atomic oxygen, ozone) produced in the gas phase between the VUV-radiation source and the substrate. However, oxidative fragmentation leading to morphological changes, oxidation products of low molecular weight and eventually to mineralization of the organic substrate is initiated by electronic excitation of the polymer leading to C–C-bond homolysis and to a complex oxidation manifold after trapping of the C-centred radicals by molecular oxygen. The pathways of oxidative functionalization or fragmentation could be differentiated by FTIR-ATR analysis of irradiated polystyrene surfaces before and after washing with acetonitrile and microscopic fluorescence analysis of the surfaces secondarily functionalized with the N,N,N-tridodecyl-triaza-triangulenium (TATA) cation. Ozonization of the polystyrene leads to oxidative functionalization of the polymer surface but cannot initiate the fragmentation of the polymer backbone. Oxidative fragmentation is initiated by electronic excitation of the polymer (contact-mode AFM analysis), and evidence of the generation of intermediate C-centred radicals is given e.g. by experiments in the absence of oxygen leading to cross-linking (solubility effects, optical microscopy, friction-mode AFM) and disproportionation (fluorescence).

VUV spectral line emission measurements in the TCABR tokamak

The study of tokamak plasma light emissions in the vacuum ultraviolet (VUV) region is an important subject since many impurity spectral emissions are present in this region. These spectral emissions can be used to determine the plasma ion temperature and density from different species and spatial positions inside plasma according to their temperatures. We have analyzed VUV spectra from 500 Å to 3200 Å wavelength in the TCABR tokamak plasma including higher diffraction order emissions. There have been identified 37 first diffraction order emissions, resulting in 28 second diffraction order, 24 third diffraction order, and 7 fourth diffraction order lines. The emissions are from impurity species such as OII, OIII, OIV, OV, OVI, OVII, CII, CIII, CIV, NIII, NIV, and NV. All the spectra beyond 1900 Å are from higher diffraction order emissions, and possess much better spectral resolution. Each strong and isolated spectral line, as well as its higher diffraction order emissions suitable for plasma diagnostic is identified and discussed. Finally, an example of ion temperature determination using different diffraction order is presented.

Storage of water molecules into biomimetic heterostructures: the role of roughness

The development of devices based on heterostructured thin films of biomolecules conveys a huge contribution on biomedical field. However, to achieve high efficiency of these devices, the storage of water molecules into these heterostructures, in order to maintain the biological molecules hydrated, is mandatory. Such hydrated environment may be achieved with lipids molecules which have the ability to rearrange spontaneously into vesicles creating a stable barrier between two aqueous compartments. Yet it is necessary to find conditions that lead to the immobilization of whole vesicles on the heterostructures. In this work, the conditions that govern the deposition of open and closed liposomes of 1.2-dipalmitoyl-sn-Glycero-3-[Phospho-rac-(1-glycerol)] (sodium Salt) (DPPG) onto polyelectrolytes cushions prepared by the layer-by-layer (LbL) method were analyzed. Electronic transitions of DPPG molecules as well as absorption coefficients were obtained by vacuum ultraviolet spectroscopy, while the elemental composition of the heterostructures was characterized by x-ray photoelectron spectroscopy (XPS). The presence of water molecules in the films was inferred by XPS and infrared spectroscopy. Quartz crystal microbalance (QCM) data analysis allowed to conclude that, in certain cases, the DPPG adsorbed amount is dependent of the bilayers number already adsorbed. Moreover, the adsorption kinetics curves of both adsorbed amount and surface roughness allowed to determine the kinetics parameters that are related with adsorption processes namely, electrostatic forces, liposomes diffusion and lipids re-organization on surface. Scaling exponents attained from atomic force microscopy images statistical analysis demonstrate that DPPG vesicles adsorption mechanism is ruled by the diffusion Villain model confirming that adsorption is governed by electrostatic forces. The power spectral density treatment enabled a thorough description of the accessible surface of the samples as well as of its inner structural properties. These outcomes proved that surface roughness influences the adsorption of DPPG liposomes onto surfaces covered by a polyelectrolyte layer. Thus, low roughness was shown to induce liposome rupture creating a lipid bilayer while high roughness allows the adsorption of whole liposomes. In addition, the fraction of open liposomes calculated from the normalized maximum adsorbed amounts decreases with the cushion roughness increase, allowing us to conclude that the surface roughness is a crucial variable that governs the adsorption of open or whole liposomes. This conclusion is fundamental for the development of well-designed sensors based on functional biomolecules incorporated in liposomes. Indeed, LbL films composed of polyelectrolytes and liposomes with and without melanin encapsulated were successfully applied to sensors of olive oil.

Characterization of molecular damage induced by UV photons and carbon ions on biomimetic heterostructures

The study of the effect of radiation on living tissues is a rather complex task to address mainly because they are made of a set of complex functional biological structures and interfaces. Particularly if one is looking for where damage is taking place in a first stage and what are the underlying reaction mechanisms. In this work a new approach is addressed to study the effect of radiation by making use of well identified molecular hetero-structures samples which mimic the biological environment. These were obtained by assembling onto a solid support deoxyribonucleic acid (DNA) and phospholipids together with a soft water-containing polyelectrolyte precursor in layered structures and by producing lipid layers at liquid/air interface with DNA as subphase. The effects of both ultraviolet (UV) radiation and carbon ions beams were systematically investigated in these heterostructures, namely damage on DNA by means vacuum ultraviolet (VUV), infrared (IR), X-Ray Photoelectron (XPS) and impedance spectroscopy. Experimental results revealed that UV affects furanose, PO2-, thymines, cytosines and adenines groups. The XPS spectrometry carried out on the samples allowed validate the VUV and IR results and to conclude that ionized phosphate groups, surrounded by the sodium counterions, congregate hydration water molecules which play a role of UV protection. The ac electrical conductivity measurements revealed that the DNA electrical conduction is arising from DNA chain electron hopping between base-pairs and phosphate groups, with the hopping distance equal to the distance between DNA base-pairs and is strongly dependent on UV radiation exposure, due loss of phosphate groups. Characterization of DNA samples exposed to a 4 keV C3+ ions beam revealed also carbon-oxygen bonds break, phosphate groups damage and formation of new species. Results from radiation induced damage carried out on biomimetic heterostructures having different compositions revealed that damage is dependent on sample composition, with respect to functional targeted groups and extent of damage. Conversely, LbL films of 1,2-dipalmitoyl-sn-Glycero-3-[Phospho-rac-(1-glycerol)] (Sodium Salt) (DPPG) liposomes, alternated with poly(allylamine hydrochloride) (PAH) revealed to be unaffected, even by prolonged UV irradiation exposure, in the absence of water molecules. However, DPPG molecules were damaged by the UV radiation in presence of water with cleavage of C-O, C=O and –PO2- bonds. Finally, the study of DNA interaction with the ionic lipids at liquid/air interfaces revealed that electrical charge of the lipid influences the interaction of phospholipid with DNA. In the presence of DNA in the subphase, the effects from UV irrladiation were seen to be smaller, which means that ionic products from biomolecules degradation stabilize the intact DPPG molecules. This mechanism may explain why UV irradiation does not cause immediate cell collapse, thus providing time for the cellular machinery to repair elements damaged by UV.

An analysis of the photoelectron and Rydberg states of formaldehyde /|nby Carol R. Lessard. -- 260 St. Catharines [Ont.] : Dept. of Chemistry, Brock University,

Although it is generally accepted that Rydberg orbitals are very large and diffuse, and that electron promotion to a Rydberg orbital is not too different from ionization of the molecule, analysis of the two types of transitions proves otherwise. The photoelectron spectrum of the 2B2 (n) ion has very little vibrational structure attached to the origin band; on the other hand, several of the Rydberg transitions which involve the promotion of the n(bZ) electron exhibit a great deal of vibrational activity. In particular, the members of the n=3 Rydberg\ series interact with and perturb each other through pseudo-Jahn-Teller vibronic coupling. The vacuum ultraviolet spectrum contains a number of features which are difficult to explain, and two unusually sharp bands can only be identified as representing some form of electron promotion in formaldehyde.

VUV-Laserablation von Spinnenseide

Spinnenseide gehört zu den stabilsten bekannten Polymerverbindungen. Spinnfäden können bis auf das Dreifache ihrer ursprünglichen Länge gedehnt werden, bevor sie reißen, und dabei mit rund 160 MJ/m³ mehr als dreimal soviel Energie absorbieren wie die stärkste synthetisch hergestellte Faser Kevlar (50 MJ/m³). Dabei weisen Spinnfäden mit 2 bis 5 Mikrometer nur ein Zehntel des Durchmessers eines menschlichen Haares auf. Das präzise, berührungslose Bearbeiten von Spinnenseide ist für verschiedene technische Anwendungen interessant, insbesondere wenn dabei ihre außergewöhnlichen Eigenschaften erhalten bleiben. Könnten die von Natur aus dünnen Seidenfäden gezielt in ihrem Durchmesser verringert werden, so wären sie unter anderem in der Mikroelektronik einzusetzen. Hier könnten sie als Trägermaterial für eine dünne, elektrisch leitfähige Schicht fungieren. Man erhielte Nanodrähte, die auch in mechanisch besonders belasteten Mikroelektronikbauteilen (MEMS) Verwendung finden könnten. In dieser Arbeit wird die Verwendung der laserinduzierten Ablation zur gezielten Bearbeitung von Haltefäden der Schwarzen Witwe (Latrodectus hesperus) beschrieben. Eingesetzt wurde ein VUV-Excimerlaser vom Typ LPF 205 (Lambda-Physik, Göttingen) mit einer Wellenlänge von 157 nm und einer Pulsdauer von 18 ns. Eine berührungslose Laserbearbeitung bei 157 nm erlaubt einen effizienten und präzisen Abtrag von Material durch Ablation aufgrund der geringen optischen Eindringtiefe von unter 100 nm oberhalb einer Schwellenfluenz (Energie/Fläche) von Φth=29 mJ/cm², ohne dabei das umgebende Material thermisch zu beeinträchtigen. Parallel zur Ablation setzt allerdings eine wellenförmige Oberflächenstrukturierung auf der Faseroberfläche ein, wodurch die mechanische Belastbarkeit der Faser entscheidend geschwächt wird. Die Ursache hierfür liegt im Abbau materialbedingter Spannungsfelder („stress release“) innerhalb einer durch das Laserlicht induzierten dünnen Schmelzschicht. Im Rahmen dieser Arbeit ist es nun gelungen, diese Strukturen durch einen anschließenden Glättungsprozeß zu entfernen. Dabei wird auf der bestrahlten Oberfläche mittels Laserlichts eine glatte Ablation erzielt. Mit feinerer Abstufung dieser Prozeßschritte konnte der Durchmesser des verwendeten Spinnenseidefadens zum Teil um 70 Prozent bis auf ca. 750 nm verringert werden. Durch Zugfestigkeitsexperimente wurde belegt, daß die mechanischen Eigenschaften der so bearbeiteten Spinnenseide weitgehend erhalten bleiben. Die im Rahmen dieser Arbeit angewandte Methode erlaubt somit eine präzise Laserablation von Spinnenseide und ähnlichen hochabsorbierenden Materialien, ohne deren Kernsubstanz in ihrer Beschaffenheit zu verändern.

Synthesis, Characterization, Luminescence and Defect Centres in CaYAl(3)O(7):Eu(3+) Red Phosphor

CaYAl(3)O(7):Eu(3+) phosphor was prepared at furnace temperatures as low as 550A degrees C by a solution combustion method. The formation of crystalline CaYAl(3)O(7):Eu(3+) was confirmed by powder X-Ray diffraction pattern. The prepared phosphor was characterized by SEM, FT-IR and photoluminescence techniques. Photoluminescence measurements indicated that emission spectrum is dominated by the red peak located at 618 nm due to the (5)D(0)-(7)F(2) electric dipole transition of Eu(3+) ions. Electron Spin Resonance (ESR) studies were carried out to identify the centres responsible for the thermoluminescence (TL) peaks. Room temperature ESR spectrum of irradiated phosphor appears to be a superposition of two distinct centres. One of the centres (centre I) with principal g-value 2.0126 is identified as an O(-) ion while centre II with an isotropic g-factor 2.0060 is assigned to an F(+) centre (singly ionized oxygen vacancy). An additional defect centre is observed during thermal annealing experiments and this centre (assigned to F(+) centre) seems to originate from an F centre (oxygen vacancy with two electrons). The F(+) centre appears to correlate with the observed high temperature TL peak in CaYAl(3)O(7):Eu(3+) phosphor.

Extended analysis of the Al-like argon spectrum

A new analysis of the aluminium-like five times ionized argon (Ar VI) spectrum in the vacuum ultraviolet region is reported in this paper. Two adjusted and 14 new energy levels and 68 new classified lines between the configurations 3s(2)3p, 3p(3), 3s3p3d, 3s(2)4p and 3s3p(2), 3s(2)(3d + 4d + 5d), 3s(2)5s, 3p(2)3d, 3s3d(2) were obtained. Atomic calculation using the HFR program was also used in the analysis.

Ellipsometric Study of Single-Crystal γ-Inse From 1.5 To 9.2 Ev

We report the component E ┴ c of the pseudodielectric-function tensor <ε(E)> = <ε1(E)> + i< ε2(E)> of γ-phase single-crystal InSe, obtained from 1.5 to 9.2 eV by vacuum-ultraviolet spectroscopic ellipsometry with the sample at room temperature. Overlayer artifacts were reduced as far as possible by measuring fresh surfaces prepared by cleavage. Accurate critical-point energies of observed structures were obtained by a combined method of spectral analysis.

Effizientes Vierwellenmischen durch Ausnutzen von Resonanzen in Quecksilber

In dieser Arbeit wird eine kohärente, kontinuierliche Strahlungsquelle im vakuum-ultravioletten (VUV) Spektrum vorgestellt. Sie basiert auf einem Vierwellenmischprozess in Quecksilberdampf mit Fundamentalstrahlen bei 253,7 nm, 407,9 nm und 545,5 nm Wellenlänge. Diese fundamentalen Strahlen werden durch frequenzverdoppelte bzw. frequenzvervierfachte Festkörperlasersysteme bereit gestellt. Durch das Ausnutzen der 6^1S-7^1S Zweiphotonenresonanz und zusätzlich der 6^1S-6^3P Einphotonenresonanz kann der Vierwellenmischprozess deutlich effizienter betrieben werden als zuvor. Eine nahe Einphotonenresonanz verringert die optimale Phasenanpassungstemperatur des Vierwellenmischprozesses, wodurch Druck- und Stoßverbreiterungen des Quecksilbers verkleinert und damit der nichtlineare Prozess effizienter wird. So können Leistungen bis zu 0,3 nW bei 121,56 nm, dem 1S-2P Lyman-alpha Übergang von Wasserstoff, erzeugt werden. Diese Lyman-alpha Quelle soll für die zukünftige Laserkühlung von Antiwasserstoff genutzt werden. rnrnNeben der Generierung von Strahlung bei Lyman-alpha kann, durch Veränderung der dritten Fundamentalwellenlänge, auch Strahlung in der Nähe zu einer Einphotonresonanz im VUV bei dem 6^1S-12^1P Übergang in Quecksilber durch Vierwellenmischen erzeugt werden. Durch diese weitere Einphotonresonanz kann die nichtlineare Suszeptibilität, verantwortlich für das Vierwellenmischen, stark vergrößert werden, ohne Einfluss auf die Phasenanpassung zu haben. Damit lässt sich der Mischprozess um drei Größenordnungen effizienter gestalten und Leistungen von 6 µW im VUV konnten realisiert werden. Dies entspricht einer Leistungsteigerung um einen Faktor 30 im Vergleich zu früheren Quellen. rnrnDarüberhinaus konnte die Zweiphotonenresonanz in Quecksilber ausführlich untersucht werden. Man erhält bei kleinen Rabifrequenzen der Fundamentalstrahlen eine geschwindigkeitsselektive Doppelresonanz, die den gleichen Ursprung wie Dunkelresonanzen in Lambda-Systemen hat. Bei hohen Rabifrequenzen kann die Anregung in das Zweiphotonenniveau so stark werden, dass auf dem 7^1S-6^1P Übergang ein Laserprozess initiiert wird. Dieser Prozess wurde hier zum ersten Mal mit kontinuierlichen Fundamentallasern nachgewiesen. Es wird gezeigt, dass der zusätzliche Laserprozess das Vierwellenmischen nicht beeinträchtigt.

Erzeugung vakuumultravioletter Strahlung durch Vierwellenmischen in einer Hohlfaser

In dieser Arbeit wird die Entwicklung und experimentelle Umsetzung einer kontinuierlichen, kohärenten Lichtquelle im vakuumultravioletten Wellenlängenbereich um 122 nm präsentiert. Diese basiert auf der nichtlinearen optischen Summenfrequenzmischung dreier Fundamentallaserstrahlen in einer mit Quecksilberdampf gefüllten Hohlfaser. Die Wellenlängen der fundamentalen Laser sind dabei an der Niveaustruktur des Quecksilbers orientiert, um eine mehrfach resonante Überhöhung der nichtlinearen Suszeptibilität zu erreichen. Der transversale Einschluss der Lichtfelder in der Faser verlängert die Wechselwirkungszone mit dem nichtlinearen Medium um mehrere Größenordnungen gegenüber dem Regime fokussierter Strahlen und erlaubt so signifikante Steigerungen der Mischeffizienz.rnrnIm Zuge dieser Arbeit wurde neben einer umfassenden mathematischen Analyse des nichtlinearen Mischprozesses unter Einfluss der Fasercharakteristika eine Apparatur zur Erzeugung und Detektion vakuumultravioletter Strahlung entwickelt. Die Generierung ausreichend hoher Dampfdichten innerhalb des 50 µm durchmessenden Faserkerns konnten spektroskopisch nachgewiesen werden.rnrnDas erste erfolgreiche Summenfrequenzmischen zu 121,26 nm in der Faser wurde demonstriert. Die erzielten Mischeffizienzen sind bereits mit denen vergleichbar, welche unter Verwendung fokussierter Strahlen erreicht werden, obwohl eine Phasenanpassung in der Faser bisher nicht möglich war. Die Ergebnisse dieser Arbeit markieren damit einen wichtigen Schritt hin zu Leistungssteigerungen kohärenter, kontinuierlicher vakuumultravioletter Lichtquellen.rnrnEine solche Quelle wird für zukünftige Laserkühlung von magnetisch gefangenem Antiwasserstoff auf dem Lyman-Alpha Übergang, sowie die Rydberganregung von Calciumionen in einer Paulfalle zur Implementierung quantenlogischer Operationen benötigt.rnrnFerner hat eine Untersuchung der, für eine effiziente Konversion essentiellen, 6^1S_0 - 7^1S_0 Zwei-Photonen Resonanz in Quecksilber Hinweise auf eine bis dato experimentell nicht beobachtete, auf einer Mehr-Photonen Anregung beruhende Licht-induzierte Drift ergeben.

O 1s excitation and ionization processes in the CO2 molecule studied via detection of low-energy fluorescence emission

Oxygen 1s excitation and ionization processes in the CO2 molecule have been studied with dispersed and non-dispersed fluorescence spectroscopy as well as with the vacuum ultraviolet (VUV) photon?photoion coincidence technique. The intensity of the neutral O emission line at 845 nm shows particular sensitivity to core-to-Rydberg excitations and core?valence double excitations, while shape resonances are suppressed. In contrast, the partial fluorescence yield in the wavelength window 300?650 nm and the excitation functions of selected O+ and C+ emission lines in the wavelength range 400?500 nm display all of the absorption features. The relative intensity of ionic emission in the visible range increases towards higher photon energies, which is attributed to O 1s shake-off photoionization. VUV photon?photoion coincidence spectra reveal major contributions from the C+ and O+ ions and a minor contribution from C2+. No conclusive changes in the intensity ratios among the different ions are observed above the O 1s threshold. The line shape of the VUV?O+ coincidence peak in the mass spectrum carries some information on the initial core excitation

Photodissociation of benzene under collision-free conditions: An ab initio/Rice-Ramsperger-Kassel-Marcus study

The ab initio/Rice-Ramsperger-Kassel-Marcus (RRKM) approach has been applied to investigate the photodissociation mechanism of benzene at various wavelengths upon absorption of one or two UV photons followed by internal conversion into the ground electronic state. Reaction pathways leading to various decomposition products have been mapped out at the G2M level and then the RRKM and microcanonical variational transition state theories have been applied to compute rate constants for individual reaction steps. Relative product yields (branching ratios) for C6H5+H, C6H4+H-2, C4H4+C2H2, C4H2+C2H4, C3H3+C3H3, C5H3+CH3, and C4H3+C2H3 have been calculated subsequently using both numerical integration of kinetic master equations and the steady-state approach. The results show that upon absorption of a 248 nm photon dissociation is too slow to be observable in molecular beam experiments. In photodissociation at 193 nm, the dominant dissociation channel is H atom elimination (99.6%) and the minor reaction channel is H-2 elimination, with the branching ratio of only 0.4%. The calculated lifetime of benzene at 193 nm is about 11 mus, in excellent agreement with the experimental value of 10 mus. At 157 nm, the H loss remains the dominant channel but its branching ratio decreases to 97.5%, while that for H-2 elimination increases to 2.1%. The other channels leading to C3H3+C3H3, C5H3+CH3, C4H4+C2H2, and C4H3+C2H3 play insignificant role but might be observed. For photodissociation upon absorption of two UV photons occurring through the neutral hot benzene mechanism excluding dissociative ionization, we predict that the C6H5+H channel should be less dominant, while the contribution of C6H4+H-2 and the C3H3+C3H3, CH3+C5H3, and C4H3+C2H3 radical channels should significantly increase. (C) 2004 American Institute of Physics.

Electrically tunable Bragg gratings in single mode polymer optical fiber

We present what is to our knowledge the first demonstration of a tunable fiber Bragg grating device in polymer optical fiber that utilizes a thin-film resistive heater deposited on the surface of the fiber. The polymer fiber was coated via photochemical deposition of a Pd/Cu metallic layer with a procedure induced by vacuum-ultraviolet radiation at room temperature. The resulting device, when wavelength tuned via joule heating, underwent a wavelength shift of 2 nm for a moderate input power of 160 mW, a wavelength to input power coefficient of-13.4 pm/mW, and a time constant of 1.7 s-1. © 2007 Optical Society of America.