Synergistic use of thermogravimetric and electrochemical techniques for thermodynamic study of TiOx (1.67 <= x <= 2.0) at 1573 K

A thermodynamic study of the Ti-O system at 1573 K has been conducted using a combination of thermogravimetric and emf techniques. The results indicate that the variation of oxygen potential with the nonstoichiometric parameter delta in stability domain of TiO2-delta with rutile structure can be represented by the relation, Delta mu o(2) = -6RT In delta - 711970(+/-1600) J/mol. The corresponding relation between non-stoichiometric parameter delta and partial pressure of oxygen across the whole stability range of TiO2-delta at 1573 K is delta proportional to P-O2(-1/6). It is therefore evident that the oxygen deficient behavior of nonstoichiometric TiO2-delta is dominated by the presence of doubly charged oxygen vacancies and free electrons. The high-precision measurements enabled the resolution of oxygen potential steps corresponding to the different Magneli phases (Ti-n O2n-1) up to n = 15. Beyond this value of n, the oxygen potential steps were too small to be resolved. Based on composition of the Magneli phase in equilibrium with TiO2-delta, the maximum value of n is estimated to be 28. The chemical potential of titanium was derived as a function of composition using the Gibbs-Duhem relation. Gibbs energies of formation of the Magneli phases were derived from the chemical potentials of oxygen and titanium. The values of -2441.8(+/-5.8) kJ/mol for Ti4O7 and -1775.4(+/-4.3) kJ/mol for Ti3O5 Obtained in this study refine values of -2436.2(+/-26.1) kJ/mol and-1771.3(+/-6.9) kJ/mol, respectively, given in the JANAF thermochemical tables.

Dielectric function and optical conductivity of TiOx (0.8

Reflection electron energy-loss spectra are reported for the family of compounds TiOx over the entire homogeneity range (0.8 < a: < 1.3). The spectra exhibit a plasmon feature on the low-energy side, while several interband transitions are prominent at higher energies. The real and imaginary parts of dielectric functions and optical conductivity for these compounds are determined using the Kramers-Kronig analysis. The results exhibit systematic behavior with varying oxygen stoichiometry.

SEM and EDS Characterisation of Layering TiOx Growth onto the Cutting Tool Surface in Hard Drilling Processes of Ti-Al-V Alloys

10 p.

Optical and electrical properties of TiOx thin films deposited by electron beam evaporation

The TiOx thin films were prepared by electron beam evaporation using TiO as the starting material. The effect of the annealing temperature on the optical and electrical properties was investigated. The spectra of X-ray photoelectron spectroscopy reveal that Ti in the films mainly exist in the forms of Ti2+ and Ti3+ below 400 degrees C 24h annealing. The charge transfer between different titanium ion contribute greatly to the color, absorption, and electrical resistance of the films. (c) 2006 Elsevier Ltd. All rights reserved.

Assembly of a high-dielectric constant thin TiOX layer directly on H-terminated semiconductor diamond

A high-dielectric constant (high-k) TiOx thin layer was fabricated on hydrogen-terminated diamond (H-diamond) surface by low temperature oxidation of a thin titanium layer in ambient air. The metallic titanium layer was deposited by sputter deposition. The dielectric constant of the resultant TiOx was calculated to be around 12. The capacitance density of the metal-oxide-semiconductor (MOS) based on the TiOx/H-diamond was as high as 0.75 µF/cm2 contributed from the high-k value and the very thin thickness of the TiOx layer. The leakage current was lower than 10-13 A at reverse biases and 10-7A at the forward bias of -2 V. The MOS field-effect transistor based on the high-k TiOx/H-diamond was demonstrated. The utilization of the high-k TiOx with a very thin thickness brought forward the features of an ideally low subthreshold swing slope of 65 mV per decade and improved drain current at low gate voltages. The advantages of the utilization high-k dielectric for diamond MOSFETs are anticipated.

Charge and spin transport in graphene devices

170 p.

Effect of acidity in TS-1 zeolites on product distribution of the styrene oxidation reaction

The role of Bronsted acidity of titanium silicalite zeolite (with different ratios of Si/Ti) in oxidation reactions of styrene has been investigated and discussed. For zeolites with Si/Ti > 42, most of the titanium is in the zeolite framework. These framework titanium species, which act both as the isolated titanium centers and as Bronsted acidity centers (together with the Bronsted acidity produced by the tetrahedral aluminum impurity introduced during synthesis), can catalyze both the epoxidation and the succeeding rearrangement reactions, thus promoting the formation of phenylacetaldehyde. With an increase in the titanium content of the zeolite, titanium will tend to stay outside the zeolite lattice, except for the TiOx nanophases which can be occluded in the zeolite channels or on the external surface. These non-framework titanium species are favorable for the carbon-carbon bond scission, leading to the production of additional benzaldehyde. The catalytic performances of these zeolites with different Si/Ti ratios are correlated here with their structural information by using solid-state NMR and UV-Vis methods. (C) 2003 Elsevier B.V. All rights reserved.

Studies on electrocatalytic performance of titanium oxide electrode modified with Pt toward the oxidation of methanol

Electrocatalytic performance of the Pr-TiOx/Ti electrode prepared with electrochemical reduction-oxidation method toward the oxidation of methanol has been studied, The experimental results showed that the Pt-TiOx/Ti electrode has a high electrocatalytic activity and good stability for the electrocatalytic oxidation of methanol, By means of electrochemical, XPS, STM and in-situ FTIR techniques, it was found that one reason for the electrode to exhibit an excellent performance is attributed to the high dispersion between nanosized Pt and TiOx particles, The low adsorption ability of the intermediate derived from methanol, such as linearly adsorbed CO species on the electrode surface due to the interaction between Pt and TiOx, also results in the excellent performance.

铂、钌共修饰的氧化钛电极对甲醇的电催化氧化

首次发现用电化学阴极还原 -阳极氧化法制得的 Pt-Ti Ox/Ti和 Pt-Ru-Ti Ox/Ti电极对甲醇氧化呈现出较高的电催化活性和稳定性 ,其中 Pt-Ru-Ti Ox/Ti电极比 Pt-Ti Ox/Ti电极具有更好的性能 .实验结果表明 ,这两种电极对甲醇氧化具有高电催化活性是由于 Pt、Ru得到了较好的分散 ,较好的稳定性可归结于Pt、Ru与 Ti Ox 协同作用导致弱的 CO吸附而使电极不易中毒 .

Electrocatalytic oxidation of methanol at the titanium oxide electrode modified with Pt microparticles

The electrocatalytic oxidation of methanol at the Titanium oxide (TiOx, x<2) film modified with Pt microparticles has been studied. The results show that the modified electrodes exhibit a significant electrocatalytic activity and good stability for the oxidation of methanol. Under the optimal conditions, the peak current density at 0.58 V for the oxidation of methanol in the positive-going sweep is about 526 mA/cm(2) at the scan rate of 5 mV/s in 0.5 mol/L CH3OH and 0.5 mol/L H2SO4 solution and the over potential of the methanol oxidation at the modified electrode increases about 30 similar to 40 mV after 70 minutes at the current density of 100 mA/cm(2) and 50 mA/cm(2). The enhanced electrocatalytic activity and good stability are ascribed to the high dispersion of Pt microparticles in and on the TiOx film and the synergistic effect between Pt microparticles and TiOx.

The active sites in different TS-1 zeolites for propylene epoxidation studied by ultraviolet resonance Raman and ultraviolet visible absorption spectroscopies

The titanium species in four kinds of titanium-containing MFI zeolites have been studied by ultraviolet (UV)-Raman and ultraviolet visible (UV-Vis) absorption spectroscopies and by the epoxidation of propylene with diluted H2O2 solution (30%). UV-Raman spectroscopy is proved to be a suitable means to estimate qualitatively the framework titanium in TS-l zeolites. Based on the comparison of the relative intensity ratio I-1125/I-380 of UV-Raman spectra, the TS-1(conv.) sample synthesized hydrothermally by the conventional procedure shows the highest amount of framework titanium. UV-Vis spectroscopy reveals that besides minor anatase. titanium species are mainly tetrahydrally coordinated into the framework for TS-l(conv.) or the Ti-ZSM-5 sample prepared by gas-solid reaction between deboronated B-ZSM-5 and TiCl4 vapor at elevated temperatures. For the TS-1(org.) and TS-1(inorg.) samples synthesized hydrothermally using tetrapropylammonium bromide (TPABr) as template and tetrabutylorthotitanite (TBOT) and TiCl3 as titanium source, respectively, the presence of mononuclear and isolated TiOx species which are proposed to bond to the zeolite extraframework is observed. In addition to the framework titanium species, these isolated TiOx species are assumed to be also active for propylene epoxidation.

Biofunktionalisierung oxidischer Titanoberflächen über eine spezifische Anbindung von biotinyliertem Fibronektin für die medizinische Anwendung

In der hier vorliegenden Dissertation wird die Entwicklung und Charakterisierung einer biomimetischen Beschichtung für Titanimplantatoberflächen, insbesondere Dentalimplantate, beschrieben. Ziel war es, die Adhäsion und Aktivität von Osteoblasten auf Titanoberflächen zu steigern und so eine Beschleunigung der Implantatintegration in das Knochengewebe zu erreichen. Hierfür wurde eine spezielle Art der biomimetischen Beschichtung entwickelt, bei der biotinyliertes Fibronektin (bFn) über Streptavidin auf eine biotinylierte TiOX-Modelloberfläche immobilisiert wurde. Die Biotinmodifizierung der TiOX-Oberfläche erfolgte hierbei über einen „Self-Assembly-Prozess“ durch sequenzielle Chemiesorption von N-(6-aminohexyl)aminopropyltrimethoxysilan sowie verschiedenen Sulfo-NHS-Biotin-Derivaten, welche den Aufbau einer Streptavidin-Monolage ermöglichten. Als ein wichtiges Resultat zeigte sich, dass die Streptavidin-Monolage effektiv die unspezifische Adsorption von Proteinen an die TiOX-Oberfläche unterbindet und hierdurch die Adhäsion von Osteoblasten auf dieser unterdrückt. Dies hat den Vorteil, dass auf eine antiadhäsive Basisbeschichtung, welche für eine spezifische Zellreaktion wichtig ist, verzichtet werden kann. Dieses osteoblastere Adhäsionsverhalten änderte sich signifikant nach Anbindung von bFn an die Streptavidin-Monolage, mit dem Ergebnis, einer drastischen Steigerung der Osteoblastenadhäsion. Weiterhin besaßen Osteoblasten auf diesen Oberflächen ein Proteinexpressionsmuster, das auf eine erhöhte Osteoinduktion schließen lässt. Es zeigte sich darüber hinaus eine verstärkte Zelladhäsion sowie eine Steigerung des osteoinduktiven Effekts auf Substraten, bei denen bFn über eine Streptavidin-Monolage immobilisiert wurde, gegenüber mit nativem Fibronektin (Fn) modifizierten TiOX-Oberflächen. Ein wesentlicher Schwerpunkt bestand daher in der Analyse der Zusammensetzung und Struktur der biomimetischen Beschichtung über „Surface Plasmon Spectroscopy“ und „Atomic Force Microscopy“. Diese ergab, dass bFn und natives Fn auf den jeweiligen Oberflächen eine unterschiedliche Konformation einnimmt. Im Gegensatz zu nativem Fn, das bei der Adsorption unter physiologischen Bedingungen auf TiOX-Oberflächen eine kompakte Konformation besitzt, nimmt bFn auf einer Streptavidin-Monolage eine entfaltete Konformation ein. Bei letzterer handelt es sich um dieselbe, welche Fn in vivo innerhalb der extrazellulären Matrix besitzt. Sie unterscheidet sich von der kompakten Fn-Konformation dahingehend, dass entlang der Fn-Achse weitere Proteinbindestellen zugänglich werden und hierdurch die Zellaffinität von Fn gesteigert wird. Die nachgewiesene Konformationsänderung kann somit als Grund für die gesteigerte Osteoblasten-Adhäsion und Aktivität auf Oberflächen mit bFn angenommen werden. Diese Kenntnisse konnten weiterhin für die Optimierung des biomimetischen Schichtsystems genutzt werden. So war es möglich, durch alternierendes Inkubieren der Biotin-aktivierten Oberfläche mit Streptavidin und bFn, ein Multilayersystem gezielt aufzubauen. Der Vorteil dieses Multilayersystems gegenüber einer einfachen Monolage aus bFn besteht in einer erhöhten Stabilität der biomimetischen Beschichtung, wodurch eine Anwendung in der Praxis erleichtert würde.

On the lateral excitation of shear modes in AlN layered resonators

In this paper we describe the fabrication and frequency characterization of different structures intended for the lateral excitation of shear modes in AlN c-axis-oriented films, which are at the same time designed to minimize the excitation of longitudinal modes. Laterally excited resonators were built on partially metallic (SiO2, W) and insulating (SiOC, Si3N4) acoustic mirrors built on silicon substrates, and on insulating mirrors (SiO2, TaOx) built on insulating glass plates. TiOx seed layers were used to stimulate the growth of highly c-axis oriented AlN films, which was confirmed by XRD and SAW measurements. Coplanar Mo electrodes of different geometries were defined on top of the AlN films to excite the shear modes. All the structures analyzed displayed a clear longitudinal mode, corresponding to an acoustic velocity of 11000 m/s, but a null or extremely weak shear response corresponding to a sound velocity of around 6350 m/s. The simulation of the frequency response based on Mason's model confirms that the shear resonance is extremely weak. The observed longitudinal modes are attributed either to the field applied between the electrodes and a conductive plane (metallic layer or Si substrate) or to the electric field parallel to the c-axis in the edges of the electrodes or in tilted grains. The low excitation of shear modes is attributed to the very low values of electric field strength parallel to the surface.