40 K Liquid Neon Energy Storage Unit

A thermal Energy Storage Unit (ESU) could be used to attenuate inherent temperature fluctuations of a cold finger, either from a cryocooler working or due to sudden income heat bursts. An ESU directly coupled to the cold source acts as a thermal buffer temporarily increasing its cooling capacity and providing a better thermal stability of the cold finger (“Power Booster mode”). The energy storage units presented here use an enthalpy reservoir based on the high latent heat of the liquid-vapour transition of neon in the temperature range 38 - 44 K to store up to 900 J, and that uses a 6 liters expansion volume at RT in order to work as a closed system. Experimental results in the power booster mode will be described: in this case, the liquid neon cell was directly coupled to the cold finger of the working cryocooler, its volume (12 cm3) allowing it to store 450 J at around 40 K. 10 W heat bursts were applied, leading to liquid evaporation, with quite reduced temperature changes. The liquid neon reservoir can also work as a temporary cold source to be used after stopping the cryocooler, allowing for a vibration-free environment. In this case the enthalpy reservoir implemented (24 cm3) was linked to the cryocooler cold finger through a gas gap heat switch for thermal coupling/decoupling of the cold finger. We will show that, by controlling the enthalpy reservoir’s pressure, 900 J can be stored at a constant temperature of 40 K as in a triple-point ESU.

Composição química e digestibilidade da vagem de algarobeira (prosopis juliflora, (sw) dc) submetida a diferentes tratamentos térmicos

The ground pods of mesquite (GPM) was submitted to different thermal treatments for two hours after wanted temperature stabilization, for making of the treatments: A = ground pods of mesquite without heat treatment (approximately 30 degrees C); B = The ground pods of mesquite treated at 60 degrees C; C = The ground pods of mesquite treated at 80 degrees C; D = The ground pods of mesquite treated at 100 degrees C and E = The ground pods of mesquite treated at 120 degrees C. Soon after, samples were collected for accomplishment for chemical analyses and in vitro digestibility. A completely randomized design with three replications was utilized. The DM, CP, NFE, CF, ADF, celluloses, lignin, ash and CE values, did not were affected (P>0.05) by temperature. It was observed a quadratic effect (P<0.01) on the contents of EE, decreasing linear effect (P<0.01) on the CC and increasing linear effect on the NDF (P<0.01) and Hemicellulose (P<0.05) contents. The in vitro dry matter digestibility and the in vitro organic matter digestibility were not affected (P>0.05) by temperature. on the other hand the in vitro protein digestibility level, showed a quadratic effect (P<0.05), decreasing after 54 degrees C.

Correction of dephasing oscillations in matter-wave interferometry

Vibrations, electromagnetic oscillations, and temperature drifts are among the main reasons for dephasing in matter-wave interferometry. Sophisticated interferometry experiments, e.g., with ions or heavy molecules, often require integration times of several minutes due to the low source intensity or the high velocity selection. Here we present a scheme to suppress the influence of such dephasing mechanisms—especially in the low-frequency regime—by analyzing temporal and spatial particle correlations available in modern detectors. Such correlations can reveal interference properties that would otherwise be washed out due to dephasing by external oscillating signals. The method is shown experimentally in a biprism electron interferometer where a perturbing oscillation is artificially introduced by a periodically varying magnetic field. We provide a full theoretical description of the particle correlations where the perturbing frequency and amplitude can be revealed from the disturbed interferogram. The original spatial fringe pattern without the perturbation can thereby be restored. The technique can be applied to lower the general noise requirements in matter-wave interferometers. It allows for the optimization of electromagnetic shielding and decreases the efforts for vibrational or temperature stabilization.

Magnetic Attitude Control System for a Small Satellite. Impact on the Thermal Performance

El principal objetivo de la tesis es estudiar el acoplamiento entre los subsistemas de control de actitud y de control térmico de un pequeño satélite, con el fin de buscar la solución a los problemas relacionados con la determinación de los parámetros de diseño. Se considera la evolución de la actitud y de las temperaturas del satélite bajo la influencia de dos estrategias de orientación diferentes: 1) estabilización magnética pasiva de la orientación (PMAS, passive magnetic attitude stabilization), y 2) control de actitud magnético activo (AMAC, active magnetic attitude control). En primer lugar se presenta el modelo matemático del problema, que incluye la dinámica rotacional y el modelo térmico. En el problema térmico se considera un satélite cúbico modelizado por medio de siete nodos (seis externos y uno interno) aplicando la ecuación del balance térmico. Una vez establecido el modelo matemático del problema, se estudia la evolución que corresponde a las dos estrategias mencionadas. La estrategia PMAS se ha seleccionado por su simplicidad, fiabilidad, bajo coste, ahorrando consumo de potencia, masa coste y complejidad, comparado con otras estrategias. Se ha considerado otra estrategia de control que consigue que el satélite gire a una velocidad requerida alrededor de un eje deseado de giro, pudiendo controlar su dirección en un sistema inercial de referencia, ya que frecuentemente el subsistema térmico establece requisitos de giro alrededor de un eje del satélite orientado en una dirección perpendicular a la radiación solar incidente. En relación con el problema térmico, para estudiar la influencia de la velocidad de giro en la evolución de las temperaturas en diversos puntos del satélite, se ha empleado un modelo térmico linealizado, obtenido a partir de la formulación no lineal aplicando un método de perturbaciones. El resultado del estudio muestra que el tiempo de estabilización de la temperatura y la influencia de las cargas periódicas externas disminuye cuando aumenta la velocidad de giro. Los cambios de temperatura se reducen hasta ser muy pequeños para velocidades de rotación altas. En relación con la estrategia PMAC se ha observado que a pesar de su uso extendido entre los micro y nano satélites todavía presenta problemas que resolver. Estos problemas están relacionados con el dimensionamiento de los parámetros del sistema y la predicción del funcionamiento en órbita. Los problemas aparecen debido a la dificultad en la determinación de las características magnéticas de los cuerpos ferromagnéticos (varillas de histéresis) que se utilizan como amortiguadores de oscilaciones en los satélites. Para estudiar este problema se presenta un modelo analítico que permite estimar la eficiencia del amortiguamiento, y que se ha aplicado al estudio del comportamiento en vuelo de varios satélites, y que se ha empleado para comparar los resultados del modelo con los obtenidos en vuelo, observándose que el modelo permite explicar satisfactoriamente el comportamiento registrado. ABSTRACT The main objective of this thesis is to study the coupling between the attitude control and thermal control subsystems of a small satellite, and address the solution to some existing issues concerning the determination of their parameters. Through the thesis the attitude and temperature evolution of the satellite is studied under the influence of two independent attitude stabilization and control strategies: (1) passive magnetic attitude stabilization (PMAS), and (2) active magnetic attitude control (AMAC). In this regard the mathematical model of the problem is explained and presented. The mathematical model includes both the rotational dynamics and the thermal model. The thermal model is derived for a cubic satellite by solving the heat balance equation for 6 external and 1 internal nodes. Once established the mathematical model of the problem, the above mentioned attitude strategies were applied to the system and the temperature evolution of the 7 nodes of the satellite was studied. The PMAS technique has been selected to be studied due to its prevalent use, simplicity, reliability, and cost, as this strategy significantly saves the overall power, weight, cost, and reduces the complexity of the system compared to other attitude control strategies. In addition to that, another control law that provides the satellite with a desired spin rate along a desired axis of the satellite, whose direction can be controlled with respect to the inertial reference frame is considered, as the thermal subsystem of a satellite usually demands a spin requirement around an axis of the satellite which is positioned perpendicular to the direction of the coming solar radiation. Concerning the thermal problem, to study the influence of spin rate on temperature evolution of the satellite a linear approach of the thermal model is used, which is based on perturbation theory applied to the nonlinear differential equations of the thermal model of a spacecraft moving in a closed orbit. The results of this study showed that the temperature stabilization time and the periodic influence of the external thermal loads decreases by increasing the spin rate. However, the changes become insignificant for higher values of spin rate. Concerning the PMAS strategy, it was observed that in spite of its extended application to micro and nano satellites, still there are some issues to be solved regarding this strategy. These issues are related to the sizing of its system parameters and predicting the in-orbit performance. The problems were found to be rooted in the difficulties that exist in determining the magnetic characteristics of the ferromagnetic bodies (hysteresis rods) that are applied as damping devices on-board satellites. To address these issues an analytic model for estimating their damping efficiency is proposed and applied to several existing satellites in order to compare the results with their respective in-flight data. This model can explain the behavior showed by these satellites.

Acreditação do Laboratório de Metrologia da Frilabo para Ensaios e Calibrações em Temperaturas

O trabalho desenvolvido centrou-se na preparação da acreditação NP EN ISO/IEC 17025 do Laboratório de Metrologia da empresa Frilabo para prestação de serviços na área das temperaturas, no ensaio a câmaras térmicas e na calibração de termómetros industriais. Considerando o âmbito do trabalho desenvolvido, são abordados nesta tese conceitos teóricos sobre temperatura e incertezas bem como considerações técnicas de medição da temperatura e cálculo de incertezas. São também referidas considerações sobre os diferentes tipos de câmaras térmicas e termómetros. O texto apresenta os documentos elaborados pelo autor sobre os procedimentos de ensaio a câmaras térmicas e respetivo procedimento de cálculo da incerteza. Também estão presentes neste texto documentos elaborados pelo autor sobre os procedimentos de calibração de termómetros industriais e respetivo procedimento de cálculo da incerteza. Relativamente aos ensaios a câmara térmicas e calibração de termómetros o autor elaborou os fluxogramas sobre a metodologia da medição da temperatura nos ensaios, a metodologia de medição da temperatura nas calibrações, e respetivos cálculos de incertezas. Nos diferentes anexos estão apresentados vários documentos tais como o modelo de folha de cálculo para tratamento de dados relativos ao ensaio, modelo de folha de cálculo para tratamento de dados relativo às calibrações, modelo de relatório de ensaio, modelo de certificado de calibração, folhas de cálculo para gestão de clientes/equipamentos e numeração automática de relatórios de ensaio e certificados de calibração que cumprem os requisitos de gestão do laboratório. Ainda em anexo constam todas as figuras relativas à monitorização da temperatura nas câmara térmicas como também as figuras da disposição dos termómetros no interior das câmaras térmicas. Todas as figuras que aparecem ao longo do documento que não estão referenciadas são da adaptação ou elaboração própria do autor. A decisão de alargar o âmbito da acreditação do Laboratório de Metrologia da Frilabo para calibração de termómetros, prendeu-se com o facto de que sendo acreditado como laboratório de ensaios na área das temperaturas, a realização da rastreabilidade dos padrões de medida internamente, permitiria uma gestão de recursos otimizada e rentabilizada. A metodologia da preparação de todo o processo de acreditação do Laboratório de Metrologia da Frilabo, foi desenvolvida pelo autor e está expressa ao longo do texto da tese incluindo dados relevantes para a concretização da referida acreditação nos dois âmbitos. A avaliação de todo o trabalho desenvolvido será efetuada pelo o organismo designado IPAC (Instituto Português de Acreditação) que confere a acreditação em Portugal. Este organismo irá auditar a empresa com base nos procedimentos desenvolvidos e nos resultados obtidos, sendo destes o mais importante o Balanço da Melhor Incerteza (BMI) da medição também conhecido por Melhor Capacidade de Medição (MCM), quer para o ensaio às câmaras térmicas, quer para a calibração dos termómetros, permitindo desta forma complementar os serviços prestados aos clientes fidelizados à Frilabo. As câmaras térmicas e os termómetros industriais são equipamentos amplamente utilizados em diversos segmentos industriais, engenharia, medicina, ensino e também nas instituições de investigação, sendo um dos objetivos respetivamente, a simulação de condições específicas controladas e a medição de temperatura. Para entidades acreditadas, como os laboratórios, torna-se primordial que as medições realizadas com e nestes tipos de equipamentos ostentem confiabilidade metrológica1, uma vez que, resultados das medições inadequados podem levar a conclusões equivocadas sobre os testes realizados. Os resultados obtidos nos ensaios a câmaras térmicas e nas calibrações de termómetros, são considerados bons e aceitáveis, uma vez que as melhores incertezas obtidas, podem ser comparadas, através de consulta pública do Anexo Técnico do IPAC, com as incertezas de outros laboratórios acreditados em Portugal. Numa abordagem mais experimental, pode dizer-se que no ensaio a câmaras térmicas a obtenção de incertezas mais baixas ou mais altas depende maioritariamente do comportamento, características e estado de conservação das câmaras, tornando relevante o processo de estabilização da temperatura no interior das mesmas. A maioria das fontes de incerteza na calibração dos termómetros são obtidas pelas características e especificações do fabricante dos equipamentos, que se traduzem por uma contribuição com o mesmo peso para o cálculo da incerteza expandida (a exatidão de fabricante, as incertezas herdadas de certificados de calibração, da estabilidade e da uniformidade do meio térmico onde se efetuam as calibrações). Na calibração dos termómetros as incertezas mais baixas obtêm-se para termómetros de resoluções mais baixas. Verificou-se que os termómetros com resolução de 1ºC não detetavam as variações do banho térmico. Nos termómetros com resoluções inferiores, o peso da contribuição da dispersão de leituras no cálculo da incerteza, pode variar consoante as características do termómetro. Por exemplo os termómetros com resolução de 0,1ºC, apresentaram o maior peso na contribuição da componente da dispersão de leituras. Pode concluir-se que a acreditação de um laboratório é um processo que não é de todo fácil. Podem salientar-se aspetos que podem comprometer a acreditação, como por exemplo a má seleção do ou dos técnicos e equipamentos (má formação do técnico, equipamento que não seja por exemplo adequado à gama, mal calibrado, etc…) que vão efetuar as medições. Se não for bem feita, vai comprometer todo o processo nos passos seguintes. Deve haver também o envolvimento do todos os intervenientes do laboratório, o gestor da qualidade, o responsável técnico e os técnicos, só assim é que é possível chegar à qualidade pretendida e à melhoria contínua da acreditação do laboratório. Outro aspeto importante na preparação de uma acreditação de um laboratório é a pesquisa de documentação necessária e adequada para poder tomar decisões corretas na elaboração dos procedimentos conducentes à referida. O laboratório tem de mostrar/comprovar através de registos a sua competência. Finalmente pode dizer-se que competência é a palavra chave de uma acreditação, pois ela manifesta-se nas pessoas, equipamentos, métodos, instalações e outros aspetos da instituição a que pertence o laboratório sob acreditação.

Use of glass transition temperature for stabilization of board's cracks of Eucalyptus grandis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

On the stabilization of conducting pernigraniline salt by the synthesis and oxidation of polyaniline in hydrophobic ionic liquids

The electrochemical polymerization of aniline in a hydrophobic room-temperature ionic liquid and the spectroelectrochemical characterization of the formed film are presented. The polymerization occurs without the presence of acid in 1-butyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide (BMMITFSI), leading to a very stable electroactive material where no degradation was observed even at high applied potentials. Both in situ UV-Vis and Raman spectroscopic studies provided evidence for the stabilization of pernigraniline salt at high oxidation potentials and that this polyaniline state is the conducting form, as was corroborated by in situ resistance measurements. These data are indicative that low conductivity is not an intrinsic property of pernigraniline salt and this point must be reconsidered.

Stabilization of an amylase from Neurospora crassa by immobilization on highly activated supports

The amylase from Neurospora crassa is an interesting enzyme, having higher stability than amylase from Aspergillus oryzea under a broad range of pH values. Moreover, the N. crassa enzyme may be immobilized on different supports with good retention of enzyme activity. The best stabilizations were achieved using Eupergit C 250 L or glyoxyl agarose, with which the enzyme remained fully active at 60C for 24 h while the soluble enzyme remained about 17%. The glyoxyl agarose immobilized enzyme had high thermostability, high optimal temperature (65C) and broad pH/activity profile, suggesting that this enzyme has potential for food and industrial applications for starch modification.

Stabilization of Endophytic Fungus Cercospora kikuchii Lipase by Spray Drying in the Presence of Maltodextrin and beta-Cyclodextrin

In this study the effects of spray-drying conditions on the retention of enzyme activity of lipase produced by the endophytic fungus Cercospora kikuchii have been investigated. Drying runs were carried out in a bench-top spray dryer with a concurrent flow regime. The influence of the variables inlet temperature of drying gas, Tgi (86.4 to 153.6 degrees C); mass flow rate of the enzymatic extract fed to the dryer, Ws (2.63 to 9.36g/min); and concentration of the drying adjuvant added to the extract, ADJ (1.95 to 12.05%), on the spray-drying performance and on product quality was evaluated through experimental planning and regression analysis. The use of maltodextrin, as a stabilizing agent, slightly improved the retention of enzyme activity compared to -cyclodextrin. Statistical optimization of the experimental results allowed the determination of the processing conditions that maximized the retention of the enzymatic activity (RAE), namely, concentration of drying adjuvants of 12.05%, inlet temperature of the drying gas of 153.6 degrees C, and flow rate of the enzymatic extract fed to the dryer of 9.36g/min for the both drying adjuvants investigated.

The effect of sodium tetrathionate stabilization on the distribution of three nuclear matrix proteins in human K562 erythroleukemia cells.

Using both conventional fluorescence and confocal laser scanning microscopy we have investigated whether or not stabilization of isolated human erythroleukemic nuclei with sodium tetrathionate can maintain in the nuclear matrix the same spatial distribution of three polypeptides (M(r) 160 kDa and 125 kDa, previously shown to be components of the internal nuclear matrix plus the 180-kDa nucleolar isoform of DNA topoisomerase II) as seen in permeabilized cells. The incubation of isolated nuclei in the presence of 2 mM sodium tetrathionate was performed at 0 degrees C or 37 degrees C. The matrix fraction retained 20-40% of nuclear protein, depending on the temperature at which the chemical stabilization was executed. Western blot analysis revealed that the proteins studied were completely retained in the high-salt resistant matrix. Indirect immunofluorescence experiments showed that the distribution of the three antigens in the final matrix closely resembled that detected in permeabilized cells, particularly when the stabilization was performed at 37 degrees C. This conclusion was also strengthened by analysis of cells, isolated nuclei and the nuclear matrix by means of confocal laser scanning microscopy. We conclude that sodium tetrathionate stabilization of isolated nuclei does not alter the spatial distribution of some nuclear matrix proteins.

Fly Ash Soil Stabilization for Non-Uniform Subgrade Soils, Volume I: Engineering Properties and Construction Guidelines, TR-461, 2005

Soil treated with self-cementing fly ash is increasingly being used in Iowa to stabilize fine-grained pavement subgrades, but without a complete understanding of the short- and long-term behavior. To develop a broader understanding of fly ash engineering properties, mixtures of five different soil types, ranging from ML to CH, and several different fly ash sources (including hydrated and conditioned fly ashes) were evaluated. Results show that soil compaction characteristics, compressive strength, wet/dry durability, freeze/thaw durability, hydration characteristics, rate of strength gain, and plasticity characteristics are all affected by the addition of fly ash. Specifically, Iowa selfcementing fly ashes are effective at stabilizing fine-grained Iowa soils for earthwork and paving operations; fly ash increases compacted dry density and reduces the optimum moisture content; strength gain in soil-fly ash mixtures depends on cure time and temperature, compaction energy, and compaction delay; sulfur contents can form expansive minerals in soil–fly ash mixtures, which severely reduces the long-term strength and durability; fly ash increases the California bearing ratio of fine-grained soil–fly ash effectively dries wet soils and provides an initial rapid strength gain; fly ash decreases swell potential of expansive soils; soil-fly ash mixtures cured below freezing temperatures and then soaked in water are highly susceptible to slaking and strength loss; soil stabilized with fly ash exhibits increased freeze-thaw durability; soil strength can be increased with the addition of hydrated fly ash and conditioned fly ash, but at higher rates and not as effectively as self-cementing fly ash. Based on the results of this study, three proposed specifications were developed for the use of self-cementing fly ash, hydrated fly ash, and conditioned fly ash. The specifications describe laboratory evaluation, field placement, moisture conditioning, compaction, quality control testing procedures, and basis of payment.

Different concentrations of Mg++ ions affect nuclear matrix protein distribution during thermal stabilization of isolated nuclei.

The nuclear matrix, a proteinaceous network believed to be a scaffolding structure determining higher-order organization of chromatin, is usually prepared from intact nuclei by a series of extraction steps. In most cell types investigated the nuclear matrix does not spontaneously resist these treatments but must be stabilized before the application of extracting agents. Incubation of isolated nuclei at 37C or 42C in buffers containing Mg++ has been widely employed as stabilizing agent. We have previously demonstrated that heat treatment induces changes in the distribution of three nuclear scaffold proteins in nuclei prepared in the absence of Mg++ ions. We studied whether different concentrations of Mg++ (2.0-5 mM) affect the spatial distribution of nuclear matrix proteins in nuclei isolated from K562 erythroleukemia cells and stabilized by heat at either 37C or 42C. Five proteins were studied, two of which were RNA metabolism-related proteins (a 105-kD component of splicing complexes and an RNP component), one a 126-kD constituent of a class of nuclear bodies, and two were components of the inner matrix network. The localization of proteins was determined by immunofluorescent staining and confocal scanning laser microscope. Mg++ induced significant changes of antigen distribution even at the lowest concentration employed, and these modifications were enhanced in parallel with increase in the concentration of the divalent cation. The different sensitivity to heat stabilization and Mg++ of these nuclear proteins might reflect a different degree of association with the nuclear scaffold and can be closely related to their functional or structural role.

RuII(α-diimine) or RuIII(α-diimine·–)? Structural, spectroscopic, and theoretical evidence for the stabilization of a prominent metal-to-Ligand charge- transfer excited-state configuration in the ground state

The new compounds [Ru(R-DAB)(acac)2] (R-DAB = 1,4-diorganyl- 1,4-diazabuta-1,3-diene; R = tert-butyl, 4-methoxyphenyl, 2,6-dimethylphenyl; acac– = 2,4-pentanedionate) exhibit intrachelate ring bond lengths 1.297temperature. The results are discussed with respect to metal-to-ligand chargetransfer (MLCT) excited states of conventional (α-diimine)- ruthenium(II) complexes and in view of other (α-diimine)- metal complexes with ambiguous oxidation-state assignments.

Activation of Leishmania (Leishmania) amazonensis arginase at low temperature by binuclear Mn(2+) center formation of the immobilized enzyme on a Ni(2+) resin

In Leishmania, arginase is responsible for the production of ornithine, a precursor of polyamines required for proliferation of the parasite. In this work, the activation kinetics of immobilized arginase enzyme from L. (L.) amazonensis were studied by varying the concentration of Mn(2+) applied to the nickel column at 23 degrees C. The intensity of the binding of the enzyme to the Ni(2+) resin was directly proportional to the concentration of Mn(2+). Conformational changes of the enzyme may occur when the enzyme interacts with immobilized Ni(2+), allowing the following to occur: (1) entrance of Mn(2+) and formation of the metal bridge; (2) stabilization and activation of the enzyme at 23 degrees C; and (3) an increase in the affinity of the enzyme to Ni(2+) after the Mn(2+) activation step. The conformational alterations can be summarized as follows: the interaction with the Ni(2+) simulates thermal heating in the artificial activation by opening a channel for Mn(2+) to enter. (C) 2010 Elsevier Inc. All rights reserved.