Travel Report from the first field trip within the SIDA supported project "Mini-grids supplied by renewable energy - improving technical and social feasibility : Including visits to Ihushi Development Center, Tweyambe Secondary School and Mavuno Project in Tanzania. Conducted in April 2011

This report describes the outcome of the first visit to Tanzania, within the project "Mini-grids supplied by renewable energy - improving technical and social feasibility". The trip included visits to three different organizations; Ihushi Development Center (IDC) near Mwanza, TIDESO near Bukoba, and Mavuno Project in Karagwe. At IDC, a brief evaluation of the current power system was done and measuring equipment for long term measurements were installed. At all three locations investigations regarding the current and future electricity demand were conducted and connections to people relevant to the study were established. The report is including as well some technical specifications as some observations regarding organization and management of the technical systems. The trip was including only short visits and therefore only brief introductions to the different organizations, based on observations done by the author. The report is hence describing the author’s understanding of the technical system and social structures after only short visits to each of the organizations, and may differ from observations done at another point in time, over a different time period, or by some other person.This report describes the outcome of the first visit to Tanzania, within the project "Mini-grids supplied by renewable energy - improving technical and social feasibility". The trip included visits to three different organizations; Ihushi Development Center (IDC) near Mwanza, TIDESO near Bukoba, and Mavuno Project in Karagwe. At IDC, a brief evaluation of the current power system was done and measuring equipment for long term measurements were installed. At all three locations investigations regarding the current and future electricity demand were conducted and connections to people relevant to the study were established. The report is including as well some technical specifications as some observations regarding organization and management of the technical systems. The trip was including only short visits and therefore only brief introductions to the different organizations, based on observations done by the author. The report is hence describing the author’s understanding of the technical system and social structures after only short visits to each of the organizations, and may differ from observations done at another point in time, over a different time period, or by some other person.

LED bulbs technical specification and testing procedure for solar home systems

The definition of technical specifications and the corresponding laboratory procedures are necessary steps in order to assure the quality of the devices prior to be installed in Solar Home Systems (SHS). To clarify and unify criteria a European project supported the development of the Universal Technical Standard for Solar Home Systems (UTSfSHS). Its principles were to generate simple and affordable technical requirements to be optimized in order to facilitate the implementation of tests with basic and simple laboratory tools even on the same SHS electrification program countries. These requirements cover the main aspects of this type of installations and its lighting chapter was developed based on the most used technology at that time: fluorescent tubes and CFLs. However, with the consolidation of the new LED solid state lighting devices, particular attention is being given to this matter and new procedures are required. In this work we develop a complete set of technical specifications and test procedures that have been designed within the frame of the UTSfSHS, based on an intense review of the scientific and technical publications related to LED lighting and their practical application. They apply to lamp reliability, performance and safety under normal, extreme and abnormal operating conditions as a simple but complete quality meter tool for any LED bulb.

A miniaturised wideband frequency synthesiser

Wideband frequency synthesisers have application in many areas, including test instrumentation and defence electronics. Miniaturisation of these devices provides many advantages to system designers, particularly in applications where extra space and weight are expensive. The purpose of this project was to miniaturise a wideband frequency synthesiser and package it for operation in several different environmental conditions while satisfying demanding technical specifications. The four primary and secondary goals to be achieved were: 1. an operating frequency range from low MHz to greater than 40 GHz, with resolution better than 1 MHz, 2. typical RF output power of +10 dBm, with maximum DC supply of 15 W, 3. synthesiser package of only 150  100  30 mm, and 4. operating temperatures from 20C to +71C, and vibration levels over 7 grms. This task was approached from multiple angles. Electrically, the system is designed to have as few functional blocks as possible. Off the shelf components are used for active functions instead of customised circuits. Mechanically, the synthesiser package is designed for efficient use of the available space. Two identical prototype synthesisers were manufactured to evaluate the design methodology and to show the repeatability of the design. Although further engineering development will improve the synthesiser’s performance, this project has successfully demonstrated a level of miniaturisation which sets a new benchmark for wideband synthesiser design. These synthesisers will meet the demands for smaller, lighter wideband sources. Potential applications include portable test equipment, radar and electronic surveillance systems on unmanned aerial vehicles. They are also useful for reducing the overall weight and power consumption of other systems, even if small dimensions are not essential.

Sapporo World Window : urban interaction through public and private screens

This paper introduces Sapporo World Window, a screen-based application that is currently under development for the new underway passage at the centre of Sapporo City. There are ten large public screens installed in the space, displaying user-generated videos about various aspects of the city and a real-time map that visualises users’ interaction with the city. The application aims to engage the general public by functioning as a unique ‘point of connection’ for socio-cultural and technological interactions, making the space a lively social place where people can have meaningful experiences of interacting with people and places of Sapporo through mobile phones (keitai) and the public screens in the space. This paper first outlines the contextual background and key concept for the application’s design. Then the paper discusses the user interaction processes, technical specifications, and interface design, followed by the conclusions and outlook.

Attitudes and expectations of technologies to manage high risk wandering and elopement in persons with dementia : an Australian perspective

Wandering is aimless and repetitive locomotion that may expose persons with dementia (PWD) to elopement, getting lost and death. This study is an Australian replication of a US study. Cross-disciplinary consensus- based analysis was applied to data from five focus groups (N =47: cognitively intact LTC residents (5), carers of PWD (11), home care workers (13) allied health professionals and health-focused engineers (7) and RNs (11). Groups received briefing about wandering monitoring and elopement management systems. Consistent with US attitudes, participants in all groups agreed on what a wandering technology should do, how it should do it, and necessary technical specifications. Within each group participants raised the need for a continuum of care for PWD and the imperative for early recognition of potentially dangerous wandering and getting lost when they occur. Global Positioning System elopement management was the preferred option. Interestingly, the prospective value of GPS to recover a lost or eloped wanderer far outweighed privacy concerns, as in the US. A pervasive theme was that technologies need to augment, but cannot replace, attentive, compassionate caregiver presence. A significant theme raised only by Australian carers of PWD was the potential for development of implantable GPS technologies and the need for public debate about attendant ethical issues. Given that 60% or more of over 200,000 Australians and 4.5 million Americans with dementia will develop wandering, there is a pressing need to develop effective locator systems that may delay institutionalization, help allay carer concern and enhance PWD safety.

Processing of enriched elemental boron (B-10 similar to 65 at. %)

Procedures were developed for purification and processing of electrodeposited enriched boron powder for control rod application in India's first commercial Proto Type Fast Breeder Reactor (PFBR). Methodology for removal of anionic (F-, Cl-, BF4-) and cationic (Fe2+, Fe3+, Ni2+) impurities was developed. Parameters for grinding boron flakes obtained after electrodeposition were optimized to obtain the boron powder having particle size less than 100 gm. The rate of removal of impurities was studied with respect to time and concentration of the reagents used for purification. Process parameters for grinding and removal of impurities were optimized. A flowsheet was proposed which helps in minimizing the purification time and concentration of the reagent used for the effective removal of impurities. The purification methodology developed in this work could produce boron that meets the technical specifications for control rod application in a fast reactor.

卫星激光通信Ⅱ地面检测和验证技术

星间激光通信终端的主要技术指标和运行性能必须事先在地面实验室条件下进行模拟检验, 因此在研制卫星激光通信终端的同时必须发展相应的系统性检测和验证平台, 主要包括激光通信性能检验、光跟瞄性能检验和光束质量检验。本文综述了卫星激光通信终端检验技术的国外进展, 介绍了我们全物理模拟的地面检测验证思路和方法。

Impacto solvencia II en un seguro de vida

La actividad aseguradora supone la transferencia de riesgos del asegurado al asegurador. El asegurador se compromete al pago de una prestación si el riesgo se realiza. Se produce un cambio en el ciclo productivo. El asegurador vende una cobertura sin conocer el momento y el coste exacto de dicha cobertura. Esta particularidad de la actividad aseguradora explica la necesidad para una entidad aseguradora de ser solvente en cada momento y ante cualquier imprevisto. Por ello, la solvencia de las entidades aseguradoras es un aspecto que se ha ido recogiendo en las distintas normativas que han regulado la actividad aseguradora y al que se ha ido dando cada vez más importancia. Actualmente la legislación vigente en materia de solvencia de las aseguradoras esta regulada por la directiva europea Solvencia I. Esta directiva establece dos conceptos para garantizar la solvencia: las provisiones técnicas y el margen de solvencia. Las provisiones técnicas son las calculadas para garantizar la solvencia estática de la compañía, es decir aquella que hace frente, en un instante temporal determinado, a los compromisos asumidos por la entidad. El margen de solvencia se destina a cubrir la solvencia dinámica, aquella que hace referencia a eventos futuros que puedan afectar la capacidad del asegurador. Sin embargo en una corriente de gestión global del riesgo en la que el sector bancario ya se había adelantado al sector asegurador con la normativa Basilea II, se decidió iniciar un proyecto europeo de reforma de Solvencia I y en noviembre del 2009 se adoptó la directiva 2009/138/CE del parlamento europeo y del consejo, sobre el seguro de vida, el acceso a la actividad de seguro y de reaseguro y su ejercicio mas conocida como Solvencia II. Esta directiva supone un profundo cambio en las reglas actuales de solvencia para las entidades aseguradoras. Este cambio persigue el objetivo de establecer un marco regulador común a nivel europeo que sea más adaptado al perfil de riesgo de cada entidad aseguradora. Esta nueva directiva define dos niveles distintos de capital: el SCR (requerimiento estándar de capital de solvencia) y el MCR (requerimiento mínimo de capital). Para el calculo del SCR se ha establecido que el asegurador tendrá la libertad de elegir entre dos modelos. Un modelo estándar propuesto por la Autoridad Europea de Seguros y Pensiones de Jubilación (EIOPA por sus siglas en inglés), que permitirá un calculo simple, y un modelo interno desarrollado por la propia entidad que deberá ser aprobado por las autoridades competentes. También se contempla la posibilidad de utilizar un modelo mixto que combine ambos, el estándar y el interno. Para el desarrollo del modelo estándar se han realizado una serie de estudios de impacto cuantitativos (QIS). El último estudio (QIS 5) ha sido el que ha planteado de forma más precisa el cálculo del SCR. Plantea unos shocks que se deberán de aplicar al balance de la entidad con el objetivo de estresarlo, y en base a los resultados obtenidos constituir el SCR. El objetivo de este trabajo es realizar una síntesis de las especificaciones técnicas del QIS5 para los seguros de vida y realizar una aplicación práctica para un seguro de vida mixto puro. En la aplicación práctica se determinarán los flujos de caja asociados a este producto para calcular su mejor estimación (Best estimate). Posteriormente se determinará el SCR aplicando los shocks para los riesgos de mortalidad, rescates y gastos. Por último, calcularemos el margen de riesgo asociado al SCR. Terminaremos el presente TFG con unas conclusiones, la bibliografía empleada así como un anexo con las tablas empleadas.

Suspensión trasera regulable pra una moto de competición: altenrativa full-floater

[ES] El objeto de este estudio consiste en el diseño de un sistema de suspensión trasera regulable y progresiva, así como el prediseño de un basculante, para una motocicleta de competición. La motocicleta compite dentro de la categoría MotoStudent, por lo que se ha realizado el estudio de acuerdo con las normas de la Organización y las especificaciones del equipo de la ETSI.

Diseño hidráulico para la red de abastecimiento de agua en el cantón de Conacaste, municipio de Comasagua, El Salvador.

[ES]El presente trabajo tiene como objetivo el diseño hidráulico de un sistema de abastecimiento de agua potable para las comunidades de La Violeta-Arcoiris, La Ceiba, San Rafael, La Finquita y La Dalia en el municipio de Comasagua, El Salvador. Para ello, se utilizaran los datos recogidos en el Plan Director para el abastecimiento y saneamiento de agua en zonas rurales del sur de La Libertad y las mediciones llevadas a cabo en terreno. Atendiendo tanto a las especificaciones técnicas y los criterios de diseño de ACUA como a los cálculos hidráulicos realizados, se ha seleccionado la mejor alternativa a desarrollar.

Diseño y fabricación de un basculante para moto de competición.

[ES]El presente documento expone el trabajo realizado en el diseño y la fabricación de un basculante para una moto de competición el cual deberá cumplir unos requisitos técnicos, formando parte del conjunto de la moto y principalmente de la suspensión trasera, teniendo presente que dicho basculante corresponderá a una moto de competición, cuyo objetivo será el de medirse con otros prototipos en una carrera y no el de una moto de calle, en la cual las prestaciones buscadas no tienen porqué ser las mismas, también se buscará cumplir unos requisitos estéticos ya que dicho basculante ha de ser también atractivo visualmente. A su vez se expondrá el método de fabricación del mismo atendiendo a criterios económicos y de obtención de los requisitos que dicho basculante debe cumplir. El método de fabricación del basculante condicionará en gran parte su diseño. A lo largo del presente documento se expondrán también diferentes alternativas a la finalmente escogida, analizando las posibles ventajas y desventajas de las mismas y justificando así la solución escogida. Dicho trabajo se enmarca en el contexto de la competición internacional MotoStudent, que se celebra en el circuito de Aragón, en el cual cada dos años universidades de todo el mundo se miden en el desafío de diseñar y fabricar una moto de 250cc con la que se medirán con sus competidores en una serie de pruebas, entre ellas, una carrera en la que se pondrán a prueba la aplicación directa de los conocimientos y experiencia adquiridos a lo largo de la vida académica de los participantes.

Na krawędzi obrazu. O po-malarskich pracach w polskiej sztuce lat sześćdziesiątych

Wydział Historyczny: Instytut Historii Sztuki

Ventiladores pulmonares – Seleção, aquisição e confiabilidade metrológica

A saúde em Portugal vive hoje mudanças significativas. A criação de modelos de Gestão Empresarial em instituições públicas visa a melhor qualidade ao menor custo. A aquisição de equipamento médico, cada vez mais sofisticado, exige das instituições esforços redobrados. A necessidade de redução dos custos acoplada à necessidade de aquisição de tecnologias cada vez mais avançadas exige que as instituições tomem mediadas mais rigorosas para melhorar o processo de aquisição. É importante estabelecer desde o início de um processo de aquisição, as exatas necessidades da instituição, com um conjunto de especificações bem detalhado do produto a adquirir bem como um conjunto exigências que devem ser feitas perante os fornecedores que salvaguardem a instituição. O conhecimento do equipamento a adquirir facilita todo o processo. Assim é de extrema importância garantir o estudo bastante alargado do equipamento, permitindo à instituição uma melhor avaliação do equipamento, aquando da seleção do mesmo. A garantia da confiabilidade metrológica é outro ponto muito importante a ter em conta no processo, uma vez que o sucesso dos cuidados de saúde parte da confiança e segurança que transmitem aos seus utentes. O objetivo deste trabalho é o estudo de Ventiladores Pulmonares (VP) focando essencialmente na seleção e aquisição destes equipamentos. Neste estudo faz-se também um estudo dos procedimentos de avaliação da confiabilidade metrológica dos VP, tendo em vista a definição dos testes de verificação a serem efetuados ao longo do processo de aquisição. É normalizado o Caderno de Encargos (CE) e respetivas especificações/requisitos técnicos, tentando comprar de acordo com as reais necessidades da instituição, visando o menor desperdício e garantido a melhor qualidade.