Development of a Continuous Emulsion Copolymerization Process in a Tubular Reactor

This contribution describes the development of a continuous emulsion copolymerization processs for vinyl acetate and n-butyl acrylate in a tubular reactor. Special features of this reactor include the use of oscillatory (pulsed) flow and internals (sieve plates) to prevent polymer fouling and promote good radial mixing, along with a controlled amount of axial mixing. The copolymer system studied (vinyl acetate and butyl acrylate) is strongly prone to composition drift due to very different reactivity ratios. An axially dispersed plug flow model, based on classical free radical copolymerization kinetics, was developed for this process and used successfully to optimize the lateral feeding profile to reduce compositional drift. An energy balance was included in the model equations to predict the effect of temperature variations on the process. The model predictions were validated with experimental data for monomer conversion, copolymer composition, average particle size, and temperature measured along the reactor length.

Thermal Runaway in Tubular Reactor Systems with n-th Order Kinetics

This paper addresses the problem of predicting the critical parameters that characterize thermal runaway in a tubular reactor with wall cooling, introducing a new view of the n-th order kinetics reactions. The paper describes the trajectories of the system in the temperature-(concentration)n plane, and deduces the conditions for the thermal risk.

Solution of a heterogeneous modeling of a horizontal-flow anaerobic immobilized biomass (HAIB) reactor by the sequencing method

A modeling study was completed to develop a methodology that combines the sequencing and finite difference methods for the simulation of a heterogeneous model of a tubular reactor applied in the treatment of wastewater. The system included a liquid phase (convection diffusion transport) and a solid phase (diffusion reaction) that was obtained by completing a mass balance in the reactor and in the particle, respectively. The model was solved using a pilot-scale horizontal-flow anaerobic immobilized biomass (HAIB) reactor to treat domestic sewage, with the concentration results compared with the experimental data. A comparison of the behavior of the liquid phase concentration profile and the experimental results indicated that both the numerical methods offer a good description of the behavior of the concentration along the reactor. The advantage of the sequencing method over the finite difference method is that it is easier to apply and requires less computational time to model the dynamic simulation of outlet response of HAIB.

Avaliação do crescimento de Ankistrodesmus braunii em reator tubular empregando diferentes concentrações de nitrato em diferentes condições de cultivo

Microalgas são organismos unicelulares, eucariontes, fotossintetizantes e eficientes fixadores de gás carbônico que apresentam grande potencial para produção de ácidos graxos além de pigmentos, como os carotenóides e a clorofila, de interesse nas indústrias de alimentos, química, farmacêutica e de cosméticos. Dentre as microalgas, o microrganismo Ankistrodesmus braunii vem sendo citado como capaz de produzir grandes quantidades de lipídios, podendo corresponder a até 73% de sua massa seca, com produção de ácidos graxos insaturados, como o ácido linolênico. Esse microrganismo se destaca do ponto de vista industrial por poder ser conduzido em reatores e em meios de cultivo complexos. As fontes de nitrogênio, as concentrações empregadas destes nutrientes, bem como o tipo de processo de cultivo interferem na composição de biomassas fotossintetizantes. O uso de reatores tubulares tem sido estudado e tem se apresentado interessante por permitir a obtenção de altas concentrações celulares. Nesse sentido, este trabalho teve a finalidade de estudar o crescimento de Ankistrodesmus braunii em reator tubular com uso de diferentes quantidades de nitrato de sódio por processos descontínuo, descontínuo alimentado e semi-contínuo. Nos cultivos descontínuos, a máxima concentração celular (Xm) encontrada foi de 1588 ± 11 mg.L-1 com uso de 20 mM de NaNO3. O uso do processo descontínuo alimentado, o qual teve adição de 20 mM de NaNO3 feito num intervalo a cada 48 horas sendo iniciada a adição no primeiro dia, permitiu a obtenção de Xm = 2753 ± 7 mg.L-1; porém não foi possível eliminar a fase lag do cultivo, levando a uma produtividade em células (Px) de 351 ± 1 mg.L-1.dia-1. O processo semi-contínuo foi eficiente para eliminar a fase lag do cultivo, permitindo a obtenção de Xm = 2399 ± 5 mg.L-1 e um aumento de até 50% em Px, que chegou a valores de 525 ± 1 mg.L-1.dia-1 em cultivos com uso de 20 mM de NaNO3. Nesta condição os teores de proteínas e lipídios nas biomassas foram de 34,8 ± 0,2% e 38,6 ± 0,2%, respectivamente. Foi observado que, independentemente do tipo de processo empregado, há um decréscimo do valor do fator de conversão de nitrogênio em células (YX/N) com o aumento da adição de NaNO3. O maior valor de YX/N foi obtido no experimento com processo semi-contínuo e uso de 2 mM de NaNO3 no meio de cultivo, com valor médio de 29,1 ± 0,1 mg mg-1 ao final do segundo ciclo. Porém, nesta condição, o teor de proteínas da biomassa foi de 17,3 ± 0,4%. Já os maiores valores de YX/N encontrados nos processos descontínuo e descontínuo alimentado foram, respectivamente, de 22,5 ± 1,6 e 7,1 ± 0,1 mg mg-1. Os resultados obtidos neste trabalho evidenciam o potencial de Ankistrodesmus braunii como fonte de proteínas e lipídios para uso industrial.

Modelagem estocástica da dispersão axial: aplicação em um reator tubular de polimerização.

Reatores tubulares de polimerização podem apresentar um perfil de velocidade bastante distorcido. Partindo desta observação, um modelo estocástico baseado no modelo de dispersão axial foi proposto para a representação matemática da fluidodinâmica de um reator tubular para produção de poliestireno. A equação diferencial foi obtida inserindo a aleatoriedade no parâmetro de dispersão, resultando na adição de um termo estocástico ao modelo capaz de simular as oscilações observadas experimentalmente. A equação diferencial estocástica foi discretizada e resolvida pelo método Euler-Maruyama de forma satisfatória. Uma função estimadora foi desenvolvida para a obtenção do parâmetro do termo estocástico e o parâmetro do termo determinístico foi calculado pelo método dos mínimos quadrados. Uma análise de convergência foi conduzida para determinar o número de elementos da discretização e o modelo foi validado através da comparação de trajetórias e de intervalos de confiança computacionais com dados experimentais. O resultado obtido foi satisfatório, o que auxilia na compreensão do comportamento fluidodinâmico complexo do reator estudado.

In-Line Monitoring of Particle Size during Emulsion Polymerization under Different Operational Conditions using NIR Spectroscopy

In the present work, the sensitivity of NIR spectroscopy toward the evolution of particle size was studied during emulsion homopolymerization of styrene (Sty) and emulsion copolymerization of vinyl acetate-butyl acrylate conducted in a semibatch stirred tank and a tubular pulsed sieve plate reactor, respectively. All NIR spectra were collected online with a transflectance probe immersed into the reaction medium. The spectral range used for the NIR monitoring was from 9 500 to 13 000 cm(-1), where the absorbance of the chemical components present is minimal and the changes in the NIR spectrum can be ascribed to the effects of light scattering by the polymer particles. Off-line measurements of the average diameter of the polymer particles by DLS were used as reference values for the development of the multi-variate NIR calibration models based on partial least squares. Results indicated that, in the spectral range studied, it is possible to monitor the evolution of the average size of the polymer particles during emulsion polymerization reactions. The inclusion of an additional spectral range, from 5 701 to 6 447 cm(-1), containing information on absorbances (""chemical information"") in the calibration models was also evaluated.

Modelling and analysis of a production plant for low density polyethylene

Dynamic model, tubular reactor, polyethylene, LDPE, discretization, simulation, sensitivity analysis, nonlinear analysis

Kinetics analysis and automated online screening of aminocarbonylation of aryl halides in flow

Temperature, pressure, gas stoichiometry, and residence time were varied to control the yield and product distribution of the palladium-catalyzed aminocarbonylation of aromatic bromides in both a silicon microreactor and a packed-bed tubular reactor. Automation of the system set points and product sampling enabled facile and repeatable reaction analysis with minimal operator supervision. It was observed that the reaction was divided into two temperature regimes. An automated system was used to screen steady-state conditions for offline analysis by gas chromatography to fit a reaction rate model. Additionally, a transient temperature ramp method utilizing online infrared analysis was used, leading to more rapid determination of the reaction activation energy of the lower temperature regimes. The entire reaction spanning both regimes was modeled in good agreement with the experimental data.

Desenvolvimento de uma rota química alternativa de síntese de SrCo0,8Fe0,2O3- e LaNi0,3Co0,7O3- para aplicação na reação de oxidação do CO

This thesis focuses on the coprecipitation synthesis method for preparation of ceramic materials with perovskite structure, their characterization and application as catalytic material in the reaction of converting CO to CO2 developing a methodological alternative route of synthesis from the middle via oxalate coprecipitation material SrCo0,8Fe0,2O3-d. In order to check the influence of this method, it was also synthesized using a combined citrate - EDTA complexing method. The material was characterized by: X-ray diffraction (XRD), Rietveld refinement method, thermogravimetry and differential thermo analysis (TG / DTA), scanning (SEM) and transmission (TEM) electron microscopy, particle size distribution and surface analysis method BET. Both methods led to post-phase synthesis, with pH as a relevant parameter. The synthesis based on the method via oxalate coprecipitation among particles led to the crystalline phase as those obtained using a combined citrate - EDTA complexing method under the same conditions of heat treatment. The nature of the reagent used via oxalate coprecipitation method produced a material with approximately 80 % lower than the average size of crystallites. Moreover, the via oxalate coprecipitation method precursors obtained in the solid state at low temperature (~ 26 oC), shorter synthesis, greater thermal stability and a higher yield of around 90-95 %, maintaining the same order of magnitude the crystallite size that the combined citrate - EDTA complexing method. For purposes of comparing the catalytic properties of the material was also synthesized by the using a combined citrate - EDTA complexing method. The evaluation of catalytic materials SrCo0,8Fe0,2O3-d LaNi0,3Co0,7O3-d was accompanied on the oxidation of CO to CO2 using a stainless steel tubular reactor in the temperature range of 75-300 oC. The conversion CO gas was evaluated in both materials on the results shaved that the firm conversion was loves for the material LaNi0,3Co0,7O3-d

Residence Time Distribution Models Derived from Non-Ideal Laminar Velocity Profiles in Tubes

The theoretical E-curve for the laminar flow of non-Newtonian fluids in circular tubes may not be accurate for real tubular systems with diffusion, mechanical vibration, wall roughness, pipe fittings, curves, coils, or corrugated walls. Deviations from the idealized laminar flow reactor (LFR) cannot be well represented using the axial dispersion or the tanks-in-series models of residence time distribution (RTD). In this work, four RTD models derived from non-ideal velocity profiles in segregated tube flow are proposed. They were used to represent the RTD of three tubular systems working with Newtonian and pseudoplastic fluids. Other RTD models were considered for comparison. The proposed models provided good adjustments, and it was possible to determine the active volumes. It is expected that these models can be useful for the analysis of LFR or for the evaluation of continuous thermal processing of viscous foods.

Study of La2-xCaxCuO4 perovskites for the low temperature water gas shift reaction

The effects of small fractions of calcium (x = 0, 0.05, 0.1, 0.15, and 0.20) on the structure and the catalytic properties of La2-xCaxCuO4 peroviskites have been investigated. The samples have been synthesized using the co-precipitation method. Perovskite-type oxides were characterized by XRD, TPR, XPS, XANES, SEM, and TEM. Catalytic tests for the water gas shift reaction (WGSR) were carried out in a tubular reactor at 290 degrees C. All samples showed a well-defined perovskite structure with surface areas between 6 and 18 m(2) g(-1). The partial substitution of La by Ca enhanced the stability of the perovskites and increased their reduction temperature. All catalysts were actives for WGSR, and the best catalytic performance was obtained for the La1.85Ca0.15CuO4 catalyst, but the samples with 5 and 10% of Ca had the best TOF values for reaction. These results can be associated to promoter effect of calcium, the high surface area, and the reducible species Cu-0 and Cu1+. (C) 2011 Elsevier B.V. All rights reserved.

Second Annual Kansas State–Nebraska Biochemical Engineering Symposium (April 29, 1972)

This booklet contains abstracts of papers presented at a biochemical engineering symposium conducted at the University of Nebraska-Lincoln on April 29, 1972. This was the second annual symposium on this subject, the first having been held at Kansas State University on June 4, 1971. It is expected that future symposia will alternate between the two campuses. ContentsS.H. Lin, Kansas State University, "Enzyme Reaction in a Tubular Reactor with Laminar Flow" Gregory C. Martin, University of Nebraska, "Estimation of Parameters in Population Models for Schizosaccharomyces pombe from Chemostat Data" Jaiprakash S. Shastry and Prakash N. Mishra, Kansas State University, "Immobilized Enzymes: Analysis of Ultrafiltration Reactors" Mark D. Young, University of Nebraska, "Modelling Unsteady-State Two-Species Data Using Ramkrishna's Staling Model" G.C.Y. Chu, Kansas State University, "Optimization of Step Aeration Waste Treatment Systems Using EVOP" Shinji Goto, University of Nebraska, "Growth of the Blue-Green Alga Microcytis aeruginosa under Defined Conditions" Prakash N. Mishra and Thomas M.C. Kuo, Kansas State University, "Digital Computer Simulation of the Activated Sludge System: Effect of Primary Clarifier on System Performance" Mark D. Young, University of Nebraska, "Aerobic Fermentation of Paunch Liquor"

Cassava starch extraction effluent treatment in a one phase tubular horizontal pilot reactor with support medium

The cassava starch industries generate a large volume of wastewater effluent that, stabilized in ponds, wastes its biogas energy and pollutes the atmosphere. To contribute with the reversion of this reality, this manipueira treatment research was developed in one phase anaerobic horizontal pilot reactor with support medium in bamboo pieces. The reactor was excavated into the ground and sealed with geomembrane in HDPE, having a volume equal to 33.6 m³ and continuous feeding by gravity. The stability indicators were pH, volatile acidity/total alkalinity ratio and biogas production. The statistical analyses were performed by a completely randomized design, with answers submitted to multivariate analysis. The organical loads in COD were 0.556; 0.670; 0.678 and 0.770 g L-1 and in volatile solids (VS) of 0.659; 0.608; 0.570 and 0.761 g L-1 for the hydraulic retention times (HRT) of 13.0; 11.5; 10.0 and 7.0 days, respectively. The reductions in COD were 88; 80; 88 and 67% and for VS of 76; 77; 65 and 61%. The biogas productions relatively to the consumed COD were 0.368; 0.795; 0.891 and 0.907 Lg-1, for the consumed VS of 0.524; 0.930; 1.757 and 0.952 Lg-1 and volumetric of 0.131; 0.330; 0.430 and 0.374 L L-1 d-1. The reactor remained stable and the bamboo pieces, in visual examination at the end of the experiment, showed to be in good physical conditions.