Discrimination d'événements par analyse des signaux enregistrés par le projet PICASSO

La matière sombre est un mystère dans le domaine de l’astrophysique depuis déjà plusieurs années. De nombreuses observations montrent que jusqu’à 85 % de la masse gravitationnelle totale de l’univers serait composée de cette matière de nature inconnue. Une théorie expliquant cette masse manquante considérerait les WIMPs (Weakly Interacting Massive Particles), particules stables, non chargées, prédites par des extensions du modèle standard, comme candidats. Le projet PICASSO (Projet d’Identification des CAndidats Supersymétriques à la matière Sombre) est une expérience qui tente de détecter directement le WIMP. Le projet utilise des détecteurs à gouttelettes de fréon (C4F10) surchauffées. La collision entre un WIMP et le noyau de fluor crée un recul nucléaire qui cause à son tour une transition de phase de la gouttelette liquide à une bulle gazeuse. Le bruit de ce phénomène est alors capté par des senseurs piézoélectriques montés sur les parois des détecteurs. Le WIMP n’est cependant pas la seule particule pouvant causer une telle transition de phase. D’autres particules environnantes peuvent former des bulles, telles les particules alpha où même des rayons gamma . Le système d’acquisition de données (DAQ) est aussi en proie à du bruit électronique qui peut être enregistré, ainsi que sensible à du bruit acoustique extérieur au détecteur. Finalement, des fractures dans le polymère qui tient les gouttelettes en place peut également causer des transitions de phase spontanées. Il faut donc minimiser l’impact de tous ces différents bruit de fond. La pureté du matériel utilisé dans la fabrication des détecteurs devient alors très importante. On fait aussi appel à des méthodes qui impliquent l’utilisation de variables de discrimination développées dans le but d’améliorer les limites d’exclusion de détection du WIMP.

Analyse des données et étude systématique de la réponse des détecteurs dans le cadre du projet PICASSO

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal

Étude et caractérisation de détecteurs à liquide en surchauffe

Les preuves astronomiques stipulent qu'environ 4\% de la densité de masse-énergie de l'univers serait composé d'atomes. Le reste est séparé entre la matière sombre, qui représente 24\% de la densité de masse-énergie, et l'énergie sombre, qui s'accapare les 71\% restant. Le neutralino est une particule prédite par la théorie de la supersymétrie et est un candidat à la composition de la matière sombre. Le Projet d'Identification des Candidats Supersymétriques Sombres (PICASSO) vise à détecter le neutralino en utilisant des détecteurs à gouttelettes de C$_4$F$_{10}$ en surchauffe. Lors du passage d'une particule dans les gouttelettes de C$_4$F$_{10}$, une transition de phase aura lieu si l'énergie déposée est au-delà du seuil prédit par le critère de nucléation d'une transition de phase (théorie de Seitz). L'onde acoustique émise durant la transition de phase est ensuite transformée en impulsion électrique par des capteurs piézoélectriques placés sur le pourtour du détecteur. Le signal est amplifié, numérisé puis enregistré afin de pouvoir être analysé par des outils numériques. L'ouvrage qui suit présente les travaux effectués sur la compréhension des signaux des détecteurs à gouttelettes en surchauffe dans le but d'améliorer la discrimination du bruit de fond. Un détecteur à petites gouttelettes, r $\approx 15\mu m$ a été étudié et comparé à une simulation Monte Carlo. Il s'est avéré que les possibilités de discrimination du bruit de fond provenant des particules alpha étaient réduites pour un détecteur à petites gouttelettes, et ce en accord avec le modèle théorique. Différentes composantes du système d'acquisition ont été testées dont le couplage entre le capteur piézoélectrique et la paroi en acrylique, l'efficacité des capteurs piézoélectriques à gain intégré et les conséquences de la force du gain sur la qualité du signal. Une comparaison avec des résultats de l'expérience SIMPLE (Superheated Instrument for Massive ParticLe Experiments) a été effectuée en mesurant des signaux de détecteurs PICASSO à l'aide d'un microphone électrostatique à électret. Il a été conclu que les détecteurs PICASSO ne parviennent pas à reproduire la discrimination quasi parfaite présentée par SIMPLE.

Fabrication et caractérisation de détecteurs à gouttelettes en surchauffe à bas bruit de fond au sein du projet PICASSO

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal

Études Monte Carlo des mesures d'étalonnage aux neutrons et aux particules alpha du détecteur PICASSO

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal

Characterization of expiration air jets and droplet size distributions immediately at the mouth opening

Size distributions of expiratory droplets expelled during coughing and speaking and the velocities of the expiration air jets of healthy volunteers were measured. Droplet size was measured using the Interferometric Mie imaging (IMI) technique while the Particle Image Velocimetry (PIV) technique was used for measuring air velocity. These techniques allowed measurements in close proximity to the mouth and avoided air sampling losses. The average expiration air velocity was 11.7 m/s for coughing and 3.9 m/s for speaking. Under the experimental setting, evaporation and condensation effects had negligible impact on the measured droplet size. The geometric mean diameter of droplets from coughing was 13.5m and it was 16.0m for speaking (counting 1 to 100). The estimated total number of droplets expelled ranged from 947 – 2085 per cough and 112 – 6720 for speaking. The estimated droplet concentrations for coughing ranged from 2.4 - 5.2cm-3 per cough and 0.004 – 0.223 cm-3 for speaking.

Modelling water droplet movement on a leaf surface

The central aim for the research undertaken in this PhD thesis is the development of a model for simulating water droplet movement on a leaf surface and to compare the model behavior with experimental observations. A series of five papers has been presented to explain systematically the way in which this droplet modelling work has been realised. Knowing the path of the droplet on the leaf surface is important for understanding how a droplet of water, pesticide, or nutrient will be absorbed through the leaf surface. An important aspect of the research is the generation of a leaf surface representation that acts as the foundation of the droplet model. Initially a laser scanner is used to capture the surface characteristics for two types of leaves in the form of a large scattered data set. After the identification of the leaf surface boundary, a set of internal points is chosen over which a triangulation of the surface is constructed. We present a novel hybrid approach for leaf surface fitting on this triangulation that combines Clough-Tocher (CT) and radial basis function (RBF) methods to achieve a surface with a continuously turning normal. The accuracy of the hybrid technique is assessed using numerical experimentation. The hybrid CT-RBF method is shown to give good representations of Frangipani and Anthurium leaves. Such leaf models facilitate an understanding of plant development and permit the modelling of the interaction of plants with their environment. The motion of a droplet traversing this virtual leaf surface is affected by various forces including gravity, friction and resistance between the surface and the droplet. The innovation of our model is the use of thin-film theory in the context of droplet movement to determine the thickness of the droplet as it moves on the surface. Experimental verification shows that the droplet model captures reality quite well and produces realistic droplet motion on the leaf surface. Most importantly, we observed that the simulated droplet motion follows the contours of the surface and spreads as a thin film. In the future, the model may be applied to determine the path of a droplet of pesticide along a leaf surface before it falls from or comes to a standstill on the surface. It will also be used to study the paths of many droplets of water or pesticide moving and colliding on the surface.

Modelling water droplet movement on a leaf surface

Modelling droplet movement on leaf surfaces is an important component in understanding how water, pesticide or nutrient is absorbed through the leaf surface. A simple mathematical model is proposed in this paper for generating a realistic, or natural looking trajectory of a water droplet traversing a virtual leaf surface. The virtual surface is comprised of a triangular mesh structure over which a hybrid Clough-Tocher seamed element interpolant is constructed from real-life scattered data captured by a laser scanner. The motion of the droplet is assumed to be affected by gravitational, frictional and surface resistance forces and the innovation of our approach is the use of thin-film theory to develop a stopping criterion for the droplet as it moves on the surface. The droplet model is verified and calibrated using experimental measurement; the results are promising and appear to capture reality quite well.

Investigation of megavoltage beams and detectors for electronic portal imaging

Accuracy of dose delivery in external beam radiotherapy is usually verified with electronic portal imaging (EPI) in which the treatment beam is used to check the positioning of the patient. However the resulting megavoltage x-ray images suffer from poor quality. The image quality can be improved by developing a special operating mode in the linear accelerator. The existing treatment beam is modified such that it produces enough low-energy photons for imaging. In this work the problem of optimizing the beam/detector combination to achieve optimal electronic portal image quality is addressed. The linac used for this study was modified to produce two experimental photon beams. These beams, named Al6 and Al10, were non-flat and were produced by 4MeV electrons hitting aluminum targets, 6 and 10mm thick respectively. The images produced by a conventional EPI system (6MV treatment beam and camera-based EPID with a Cu plate & Gd2O2S screen ) were compared with the images produced by the experimental beams and various screens with the same camera). The contrast of 0.8cm bone equivalent material in 5 cm water increased from 1.5% for the conventional system to 11% for the combination of Al6 beam with a 200mg/cm2 Gd2O2S screen. The signal-to-noise ratio calculated for 1cGy flood field images increased by about a factor of two for the same EPI systems. The spatial resolution of the two imaging systems was comparable. This work demonstrates that significant improvements in portal image contrast can be obtained by simultaneous optimization of the linac spectrum and EPI detector.

Learning detectors quickly with stationary statistics

Computer vision is increasingly becoming interested in the rapid estimation of object detectors. The canonical strategy of using Hard Negative Mining to train a Support Vector Machine is slow, since the large negative set must be traversed at least once per detector. Recent work has demonstrated that, with an assumption of signal stationarity, Linear Discriminant Analysis is able to learn comparable detectors without ever revisiting the negative set. Even with this insight, the time to learn a detector can still be on the order of minutes. Correlation filters, on the other hand, can produce a detector in under a second. However, this involves the unnatural assumption that the statistics are periodic, and requires the negative set to be re-sampled per detector size. These two methods differ chie y in the structure which they impose on the co- variance matrix of all examples. This paper is a comparative study which develops techniques (i) to assume periodic statistics without needing to revisit the negative set and (ii) to accelerate the estimation of detectors with aperiodic statistics. It is experimentally verified that periodicity is detrimental.

A comparison of the performance of a brand of broad-band and several brands of narrow-band bat detectors in two different habitat types.

The use of bat detectors to monitor bat activity is common. Although several papers have compared the performance of different brands, none have dealt with the effect of different habitats nor have they compared narrow- and broad-band detectors. In this study the performance of four brands of ultrasonic bat detector, including three narrowband and one broad-band model, were compared for their ability to detect a 40 kHz continuous sound of variable amplitude along 100 metre transects. Transects were laid out in two contrasting bat habitat types: grassland and forest. Results showed that the different brands of detector differed in their ability to detect the source in terms of maximum and minimum detectable distance of the source. The rate of sound degradation with distance as measured by each brand was also different. Significant differences were also found in the performance of different brands in open grassland versus deep forest. No significant differences were found within any brand of detector. Though not as sensitive as narrow-band detectors, broad-band models hold an advantage in their ability to identify species where several species are found sympatrically.

DroplIT, an improved image analysis method for droplet identification in high-throughput crystallization trials

The application of robotics to protein crystallization trials has resulted in the production of millions of images. Manual inspection of these images to find crystals and other interesting outcomes is a major rate-limiting step. As a result there has been intense activity in developing automated algorithms to analyse these images. The very first step for most systems that have been described in the literature is to delineate each droplet. Here, a novel approach that reaches over 97% success rate and subsecond processing times is presented. This will form the seed of a new high-throughput system to scrutinize massive crystallization campaigns automatically. © 2010 International Union of Crystallography Printed in Singapore-all rights reserved.

Retrieving trip information from a discrete detectors network : The case of Brisbane Bluetooth detectors

Automatic Vehicle Identification Systems are being increasingly used as a new source of travel information. As in the last decades these systems relied on expensive new technologies, few of them were scattered along a networks making thus Travel-Time and Average Speed estimation their main objectives. However, as their price dropped, the opportunity of building dense AVI networks arose, as in Brisbane where more than 250 Bluetooth detectors are now installed. As a consequence this technology represents an effective means to acquire accurate time dependant Origin Destination information. In order to obtain reliable estimations, however, a number of issues need to be addressed. Some of these problems stem from the structure of a network made out of isolated detectors itself while others are inherent of Bluetooth technology (overlapping detection area, missing detections,\...). The aim of this paper is threefold: First, after having presented the level of details that can be reached with a network of isolated detectors we present how we modelled Brisbane's network, keeping only the information valuable for the retrieval of trip information. Second, we give an overview of the issues inherent to the Bluetooth technology and we propose a method for retrieving the itineraries of the individual Bluetooth vehicles. Last, through a comparison with Brisbane Transport Strategic Model results, we highlight the opportunities and the limits of Bluetooth detectors networks. The aim of this paper is twofold. We first give a comprehensive overview of the aforementioned issues. Further, we propose a methodology that can be followed, in order to cleanse, correct and aggregate Bluetooth data. We postulate that the methods introduced by this paper are the first crucial steps that need to be followed in order to compute accurate Origin-Destination matrices in urban road networks.

Simulating droplet motion on virtual leaf surfaces

A curvilinear thin film model is used to simulate the motion of droplets on a virtual leaf surface, with a view to better understand the retention of agricultural sprays on plants. The governing model, adapted from Roy et al. (2002 J. Fluid Mech. 454, 235–261) with the addition of a disjoining pressure term, describes the gravity- and curvature driven flow of a small droplet on a complex substrate: a cotton leaf reconstructed from digitized scan data. Coalescence is the key mechanism behind spray coating of foliage, and our simulations demonstrate that various experimentally observed coalescence behaviours can be reproduced qualitatively. By varying the contact angle over the domain, we also demonstrate that the presence of a chemical defect can act as an obstacle to the droplet’s path, causing break-up. In simulations on the virtual leaf, it is found that the movement of a typical spray size droplet is driven almost exclusively by substrate curvature gradients. It is not until droplet mass is sufficiently increased via coalescence that gravity becomes the dominating force.

Droplet digital PCR as a useful tool for the quantitative detection of Enterovirus 71

Hand, foot and mouth disease (HFMD) is a contagious viral disease that frequently affects infants and children and present with blisters and flu-like symptoms. This disease is caused by a group of enteroviruses such as enterovirus 71 (EV71) and coxsackievirus A16 (CA16). However, unlike other HFMD causing enteroviruses, EV71 have also been shown to be associated with more severe clinical manifestation such as aseptic meningitis, brainstem and cerebellar encephalitis which may lead to cardiopulmonary failure and death. Clinically, HFMD caused by EV71 is indistinguishable from other HFMD causing enteroviruses such as CA16. Molecular diagnosis methods such as the use of real-time PCR has been used commonly for the identification of EV71. In this study, two platforms namely the real-time PCR and the droplet digital PCR were compared for the detection quantitation of known EV71 viral copy number. The results reveal accurate and consistent results between the two platforms. In summary, the droplet digital PCR was demonstrated to be a promising technology for the identification and quantitation of EV71 viral copy number.