Substrate influence on the properties of doped thin silicon layers grown by Cat-CVD

We present structural and electrical properties for p- and n-type layers grown close to the transition between a-Si:H and nc-Si:H onto different substrates: Corning 1737 glass, ZnO:Al-coated glass and stainless steel. Structural properties were observed to depend on the substrate properties for samples grown under the same deposition conditions. Different behaviour was observed for n- and p-type material. Stainless steel seemed to enhance crystallinity when dealing with n-type layers, whereas an increased crystalline fraction was obtained on glass for p-type samples. Electrical conduction in the direction perpendicular to the substrate seemed to be mainly determined by the interfaces or by the existence of an amorphous incubation layer that might determine the electrical behaviour. In the direction perpendicular to the substrate, n-type layers exhibited a lower resistance value than p-type ones, showing better contact properties between the layer and the substrate.

Influence of the substrate on structure and magnetic properties of Co-N thin films

Cubic cobalt nitride films were grown onto different single crystalline substrates Al2O3 (0 0 0 1) and (1 1 View the MathML source 0), MgO (1 0 0) and (1 1 0) and TiO2 (1 0 0) and (1 1 0). The films display low atomic densities compared with the bulk material, are ferromagnetic and have metallic electrical conductivity. X-ray diffraction and X-ray absorption fine structure confirm the cubic structure of the films and with RBS results indicate that samples are not homogeneous at the microscopic scale, coexisting Co4+xN nitride with nitrogen rich regions. The magnetization of the films decreases with increase of the nitrogen content, variation that is shown to be due to the decrease of the cobalt density, and not to a decrease of the magnetic moment per cobalt ion. The films are crystalline with a nitrogen deficient stoichiometry and epitaxial with orientation determined by the substrate.

Producció de biopolímers amb cultius bacterians mixtes. Comparació de tres reactors discontinus seqüencials (SBR) amb diferents condicions operacionals

La producció de biopolímers (polihidroxialcanoats (PHA) i substàncies polimèriques extracel·lulars (EPS)) a nivell industrial, resulta una nova àrea d’investigació que recull diverses disciplines, entre elles les Ciències Ambientals. Aquest projecte final de carrera amb el títol: “Producció de biopolímers amb cultius bacterians mixtes”, s’ha desenvolupat sota la supervisió de la directora de projecte Dra. María Eugenia Suárez Ojeda del Departament d’Enginyeria Química de la Universitat Autònoma de Barcelona (UAB) i s’ha dut a terme per l’estudiant Jordi Pérez i Forner de la Llicenciatura de Ciències Ambientals, Facultat de Ciències de la UAB, en el Departament d’Enginyeria Química de la mateixa universitat. L’objectiu d’aquest projecte ha estat produir biopolímers simultàniament amb l’eliminació de fòsfor i matèria orgànica en aigües residuals per obtenir un residu final amb un alt valor afegit. Aquests biopolímers reuneixen les característiques necessàries per a poder competir amb els plàstics convencionals i així, reduir l’elevat consum del petroli i la generació de residus no biodegradables. En aquest projecte s’ha dut a terme la posta en marxa d’un reactor discontinu seqüencial (SBR) per a l’acumulació de biopolímers amb cultius bacterians mixtes. Diferents investigadors han estudiat que aquests tipus de cultius bacterians arriben a nivells de fins el 53-97% [Pijuan et al., 2009] de contingut de biopolímers a la biomassa, sometent als microorganismes a diferents situacions d’estrés ja sigui per dèficit de nutrients o per variacions en les fases de feast-famine (festí-fam). Durant el projecte, s’ha realitzat el monitoratge del reactor alimentat amb una aigua sintètica, elaborada en el laboratori, amb les característiques d’un aigua residual provinent de la industria làctica. S’ha sotmès als microorganismes a diferents condicions operacionals, una d’elles amb limitació de fòsfor com a nutrient i una tercera condició amb una variació a les fases feast-famine. D’altra banda, com a segon objectiu, s’ha analitzat el contingut de biopolímers a la biomassa de dos SBRs més, del grup de recerca Bio-GLS del Departament d’Enginyeria Química de la UAB, alimentats amb diferents fonts de carboni, glicerol i àcids grassos de cadena llarga (AGCLL), per observar les influències que té el tipus de substrat en l’acumulació de biopolímers. Els resultats obtinguts en la primera part d’aquest projecte han estat similars als resultats d’altres investigadors [Pijuan et al., 2009; Guerrero et al., 2012]. S’ha determinat que sotmetre als microorganismes a situacions d’estrés té un efecte directe pel que fa a l’acumulació de biopolímers. També s’ha observat com al mateix temps que acumulaven aquests compostos, els microorganismes desenvolupaven la seva tasca de depurar l’aigua residual, obtenint al final del cicle una aigua amb un baix contingut en matèria orgànica i altres contaminants com amoni i fòsfor, en aquest cas. En la segona part del projecte, s’ha observat com el tipus de substrat té un efecte directe pel que fa a l’acumulació de biopolímers i també a l’activitat metabòlica dels microorganismes. Per tant, s’ha conclòs que la producció de biopolímers mitjançant la depuració d’aigües residuals es una via d’investigació molt prometedora pel que fa als resultats obtinguts. Alhora que es tracta un residu, s’obté una producte residual amb un alt valor afegit que pot ser utilitzat per la producció de bioplàstics 100% biodegradables.

Dynamic wetting of complex liquids

A simple dependency between contact angle θ and velocity or surface tension has been predicted for the wetting and dewetting behavior of simple liquids. According to the hydrodynamic theory, this dependency was described by Cox and Voinov as θ ∼ Ca^(1/3) (Ca: Capillary number). For more complex liquids like surfactant solutions, this prediction is not directly given.rnHere I present a rotating drum setup for studying wetting/dewetting processes of surfactant solutions on the basis of velocity-dependent contact angle measurements. With this new setup I showed that surfactant solutions do not follow the predicted Cox-Voinov relation, but showed a stronger contact angle dependency on surface tension. All surfactants independent of their charge showed this difference from the prediction so that electrostatic interactions as a reason could be excluded. Instead, I propose the formation of a surface tension gradient close to the three-phase contact line as the main reason for the strong contact angle decrease with increasing surfactant concentration. Surface tension gradients are not only formed locally close to the three-phase contact line, but also globally along the air-liquid interface due to the continuous creation/destruction of the interface by the drum moving out of/into the liquid. By systematically hindering the equilibration routes of the global gradient along the interface and/or through the bulk, I was able to show that the setup geometry is also important for the wetting/dewetting of surfactant solutions. Further, surface properties like roughness or chemical homogeneity of the wetted/dewetted substrate influence the wetting/dewetting behavior of the liquid, i. e. the three-phase contact line is differently pinned on rough/smooth or homogeneous/inhomogeneous surfaces. Altogether I showed that the wetting/dewetting of surfactant solutions did not depend on the surfactant type (anionic, cationic, or non-ionic) but on the surfactant concentration and strength, the setup geometry, and the surface properties.rnSurfactants do not only influence the wetting/dewetting behavior of liquids, but also the impact behavior of drops on free-standing films or solutions. In a further part of this work, I dealt with the stability of the air cushion between drop and film/solution. To allow coalescence between drop and substrate, the air cushion has to vanish. In the presence of surfactants, the vanishing of the air is slowed down due to a change in the boundary condition from slip to no-slip, i. e. coalescence is suppressed or slowed down in the presence of surfactant.

A Cross-Generational Analysis of Spanish-to-English Lexico-Semantic Phenomena in Emerging Miami English

Sociolinguists have documented the substrate influence of various languages on the formation of dialects in numerous ethnic-regional setting throughout the United States. This literature shows that while phonological and grammatical influences from other languages may be instantiated as durable dialect features, lexical phenomena often fade over time as ethnolinguistic communities assimilate with contiguous dialect groups. In preliminary investigations of emerging Miami Latino English, we have observed that lexical forms based on Spanish lexical forms are not only ubiquitous among the speech of the first generation Cuban Americans but also of the second. Examples, observed in field work, casual observation, and studied formally in an experimental context include the following: “get down from the car,” which derives from the Spanish equivalent, bajar del carro instead of “get out of the car”. The translation task administered to thirty-one participants showed a variety lexical phenomena are still maintained at equal or higher frequencies.

Influence Of Substrate Steps On The Catalytic Properties Of Pt Layers: The Ethanol Electrooxidation Reaction.

The ethanol oxidation reaction (EOR) is investigated on Pt/Au(hkl) electrodes. The Au(hkl) single crystals used belong to the [n(111)x(110)] family of planes. Pt is deposited following the galvanic exchange of a previously deposited Cu monolayer using a Pt(2+) solution. Deposition is not epitaxial and the defects on the underlying Au(hkl) substrates are partially transferred to the Pt films. Moreover, an additional (100)-step-like defect is formed, probably as a result of the strain resulting from the Pt and Au lattice mismatch. Regarding the EOR, both vicinal Pt/Au(hkl) surfaces exhibit a behavior that differs from that expected for stepped Pt; for instance, the smaller the step density on the underlying Au substrate, the greater the ability to break the CC bond in the ethanol molecule, as determined by in situ Fourier transform infrared spectroscopy measurements. Also, we found that the acetic acid production is favored as the terrace width decreases, thus reflecting the inefficiency of the surface array to cleave the ethanol molecule.

Influence of substrate surface topography in the deposition of nanostructured diamond-like carbon films by high density plasma chemical vapor deposition

In this work, we have studied the influence of the substrate surface condition on the roughness and the structure of the nanostructured DLC films deposited by High Density Plasma Chemical Vapor Deposition. Four methods were used to modify the silicon wafers surface before starting the deposition processes of the nanostructured DLC films: micro-diamond powder dispersion, micro-graphite powder dispersion, and roughness generation by wet chemical etching and roughness generation by plasma etching. The reference wafer was only submitted to a chemical cleaning. It was possible to see that the final roughness and the sp(3) hybridization degree strongly depend on the substrate surface conditions. The surface roughness was observed by AFM and SEM and the hybridization degree of the DLC films was analyzed by Raman Spectroscopy. In these samples, the final roughness and the sp(3) hybridization quantity depend strongly on the substrate surface condition. Thus, the effects of the substrate surface on the DLC film structure were confirmed. These phenomena can be explained by the fact that the locally higher surface energy and the sharp edges may induce local defects promoting the nanostructured characteristics in the DLC films. (C) 2008 Elsevier B.V. All rights reserved.

Influence of the bonding substrate in dental composite polymerization stress testing

Our objective was to compare the polymerization stress (sigma(pol)) of a series of composites obtained using poly(methyl methacrylate) (PMMA) or glass as bonding substrates, and to compare the results with those from in vitro microleakage of composite restorations. The tested hypothesis was that stress values obtained in a less rigid testing system (i.e. using PMMA) would show a better relationship with microleakage data. Five dental composites were tested: Filtek Z250 (FZ), Z100 (Z1), Concept (CO), Durafill (DU) and Heliomolar (HM). sigma(pol) was determined in 1 mm high specimens inserted between two rods (empty set = 5 mm) of either PMMA or glass. The composite elastic modulus (E) was obtained by three-point bending. sigma(pol) and E data were submitted to a one-way analysis of variance/Tukey test (alpha = 0.05). For the microleakage test (MI), bovine incisors received cylindrical cavities (empty set = 5 mm, h = 2 mm), which were restored in bulk. After storage for 24 h in water, specimens were subjected to dye penetration using AgNO(3) as tracer. Specimens were sectioned twice, perpendicularly, and microleakage was measured (in millimeters) under 20x magnification. Data from MI were submitted to the Kruskal-Wallis test. Means (SD) of sigma(pol) (MPa) using glass/PMMA were FZ: 7.5(1.8)(A)/2.5(0.2)(bc); Z1: 7.3(0.5)(A)/2.8(0.3)(ab); CO: 6.8(1.1)(A)/3.2(0.5)(a); DU: 4.5(0.7)(B)/2.0(0.2)(bc); HM: 3.5(0.2)(B)/2.3(0.3)(c). sigma(pol) obtained using PMMA rods were 34-67% lower than with glass. Means (SD) for tooth average/tooth maximum microleakage were FZ: 0.92(0.19)(B)/1.53(0.30)(a); Z1: 1.19(0.21)(A)/1.75(0.20)(a); CO: 1.26(0.25)(A)/1.78(0.24)(a); DU: 0.83(0.30)(B)/1.68(0.46)(a): HM: 0.81(0.27)(B)/1.64(0.54)(a). The tested hypothesis was confirmed, as the composites showed the same ordering both in the polymerization stress test using PMMA rods and in the microleakage test. (C) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Influence of the substrate in germination of lychee seeds

The lychee is, all over the world, considered as the "queen of the fruits" due to the delicacy of its appearance and flavor. Although it was only recently that it started to have economical importance in Brazil, the lychee is already calling the attention of numerous farmers, mainly those who cultivate citric fruits and/or sugarcane in the State of São Paulo, due to the constant and at the same time growing necessity of finding new alternative crops. Considering that the commercial cultivation of lychee plants in the field requires the previous obtainment of rootstocks viewing to reduce the genetic variability and the length of the juvenile period displayed by plants resulting directly from the seeds, finding ways to improve the germination performance of lychee seeds for the production of rootstock plants is of considerable economic importance. Thus, the objective of this experiment was to test five substrates for the germination of lychee seeds: (1) vermiculite, (2) washed sand, (3) filter paper, (4) carbonized rice hull, and (5) sphagnum. The results showed that the period of time required by a lychee seed to germinate is a short one thus reinforcing the importance of providing a suitable substrate for the germination to take place. It was found that the substrates which apparently allowed the best combinations of water and oxygen availability for the seeds - washed sand and carbonized rice hull - were those leading to the fastest and highest germination values.

Influence of substrate topography on the growth and magnetic properties of obliquely deposited amorphous nanocolumns of Fe–Ni

We investigated the influence of substrate surface roughness on the structural and magnetic properties of obliquely deposited amorphous nanocolumns of Fe–Ni. Experiments showed that the surface roughness of the substrate greatly determines the morphology of the columnar structures and this in turn has a profound influence on the magnetic properties. Nucleation of Fe–Ni nanocolumns on a smooth silicon substrate was at random, while that on a rough glass substrate was defined by the irregularities on the substrate surface. It has been found that magnetic interaction between the nanocolumns prepared on a silicon substrate was due to their small inter-column separation. Well separated nanocolumns on a glass substrate resulted in exchange isolated magnetic domains. The size, shape and the distribution of nanocolumns can be tailored by appropriately choosing the surface roughness of the substrate. This will find potential applications in thin film magnetism.

Influence of substrate on corneal epithelial cell viability within ocular surface models

Corneal tissue engineering has improved dramatically over recent years. It is now possible to apply these technological advancements to the development of superior in vitro ocular surface models to reduce animal testing. We aim to show the effect different substrates can have on the viability of expanded corneal epithelial cells and that those which more accurately mimic the stromal surface provide the most protection against toxic assault. Compressed collagen gel as a substrate for the expansion of a human epithelial cell line was compared against two well-known substrates for modeling the ocular surface (polycarbonate membrane and conventional collagen gel). Cells were expanded over 10 days at which point cell stratification, cell number and expression of junctional proteins were assessed by electron microscopy, immunohistochemistry and RT-PCR. The effect of increasing concentrations of sodium lauryl sulphate on epithelial cell viability was quantified by MTT assay. Results showed improvement in terms of stratification, cell number and tight junction expression in human epithelial cells expanded upon either the polycarbonate membrane or compressed collagen gel when compared to a the use of a conventional collagen gel. However, cell viability was significantly higher in cells expanded upon the compressed collagen gel. We conclude that the more naturalistic composition and mechanical properties of compressed collagen gels produces a more robust corneal model.

Influence of the substrate in germination of lychee seeds

A lichia é considerada em todo o mundo como a rainha das frutas, por sua aparência e sabor delicado. Atualmente, a cultura vem despertando interesse, principalmente no Estado de São Paulo, onde, em virtude dos problemas enfrentados pelos agricultores, destacando-se os de laranja e cana-de-açúcar, a procura por alternativas agrícolas vem se intensificando ainda mais. A propagação através de sementes não é recomendada comercialmente, pois as plantas de pé-franco são geneticamente muito desuniformes e apresentam período juvenil muito longo, demorando até 10 anos para entrar em produção; no entanto, a semente pode ser utilizada para a obtenção de porta-enxertos. Observou-se que a germinação de sementes de lichia ocorre rapidamente, reforçando a importância do uso de um substrato adequado. Pela análise dos resultados obtidos, verifica-se que o substrato que aparentemente permitiu as melhores combinações de água e disponibilidade de oxigênio para as sementes - casca de arroz carbonizada e areia lavada, foi o que proporcionou valores de germinação mais rápidos e mais altos.

Influence of Fungal Contamination on Substrate Carrying by the Leafcutter Ant Atta sexdens rubropilosa (Hymenoptera: Formicidae)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)