Using an LED as a sensor and visible light communication device in a smart illumination system

The need for more efficient illumination systems has led to the proliferation of Solid-State Lighting (SSL) systems, which offer optimized power consumption. SSL systems are comprised of LED devices which are intrinsically fast devices and permit very fast light modulation. This, along with the congestion of the radio frequency spectrum has paved the path for the emergence of Visible Light Communication (VLC) systems. VLC uses free space to convey information by using light modulation. Notwithstanding, as VLC systems proliferate and cost competitiveness ensues, there are two important aspects to be considered. State-of-the-art VLC implementations use power demanding PAs, and thus it is important to investigate if regular, existent Switched-Mode Power Supply (SMPS) circuits can be adapted for VLC use. A 28 W buck regulator was implemented using a off-the-shelf LED Driver integrated circuit, using both series and parallel dimming techniques. Results show that optical clock frequencies up to 500 kHz are achievable without any major modification besides adequate component sizing. The use of an LED as a sensor was investigated, in a short-range, low-data-rate perspective. Results show successful communication in an LED-to-LED configuration, with enhanced range when using LED strings as sensors. Besides, LEDs present spectral selective sensitivity, which makes them good contenders for a multi-colour LED-to-LED system, such as in the use of RGB displays and lamps. Ultimately, the present work shows evidence that LEDs can be used as a dual-purpose device, enabling not only illumination, but also bi-directional data communication.

Street lighting mesh network protocol

The digital revolution of the 21st century contributed to stem the Internet of Things (IoT). Trillions of embedded devices using the Internet Protocol (IP), also called smart objects, will be an integral part of the Internet. In order to support such an extremely large address space, a new Internet Protocol, called Internet Protocol Version 6 (IPv6) is being adopted. The IPv6 over Low Power Wireless Personal Area Networks (6LoWPAN) has accelerated the integration of WSNs into the Internet. At the same time, the Constrained Application Protocol (CoAP) has made it possible to provide resource constrained devices with RESTful Web services functionalities. This work builds upon previous experience in street lighting networks, for which a proprietary protocol, devised by the Lighting Living Lab, was implemented and used for several years. The proprietary protocol runs on a broad range of lighting control boards. In order to support heterogeneous applications with more demanding communication requirements and to improve the application development process, it was decided to port the Contiki OS to the four channel LED driver (4LD) board from Globaltronic. This thesis describes the work done to adapt the Contiki OS to support the Microchip TM PIC24FJ128GA308 microprocessor and presents an IP based solution to integrate sensors and actuators in smart lighting applications. Besides detailing the system’s architecture and implementation, this thesis presents multiple results showing that the performance of CoAP based resource retrievals in constrained nodes is adequate for supporting networking services in street lighting networks.

Gesture based IoT light control for smart clothing

In this paper, a smart wireless wristband is proposed. The potential of innovative gesture based interactivity with connected lighting solutions is reviewed. The solution is intended to offer numerous benefits, in terms of ease of use, and enhanced dynamic interactive functionality. A comparative analysis will be carried out between this work and existing solutions. The evolution of lighting and gesture controls will be discussed and an overview of alternative applications will be provided, as part of the critical analysis.

Automatic dimming multi-lamp fluorescent management system with active input power factor corrector stage

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Distribution of Smart Solutions for External Lighting in Switzerland - Case C2 Smartlight Ltd.

Establishing of export operations is the key to the competitiveness for all producing companies in high-tech industry. Distribution partnerships between exporting producer and local distributors of relevant foreign market are utilized by SMEs to gain cost-efficiency of operation. The purpose of this study was to investigate the Swiss market of outdoor lighting solutions and propose distribution channels for the case of company C2 SmartLight Ltd. The literature framework consists of three main parts: description of distribution channels for business products, the selection process of the distributor and management of the distributors. The empirical part of this study composed of the observation of Swiss lighting market, highlighting key customers, trends of energy efficiency and key industry players of the lighting market. The aim was to identify potential distribution channels, which reach the target customer groups and identify the market opportunity. Secondly, the data was collected through semi-structured phone interviews. The company, which operates in outdoor lighting business and has an established distributor in Switzerland, was interviewed and used as a benchmark. As a result of this research the market opportunity for distribution of C2 SmartLight products was identified based on potential customers and market need. C2 SmartLight Ltd. should establish a connection with wholesalers that distribute easy to handle and store electrical equipment. The results of this study can be used by other SME companies, operating in a similar field of economy, for selection of distributors.

Multiprotocol Android Application for Smart Control and Monitoring in Buildings

This paper presents a multiprotocol mobile application for building automation which supports and enables the integration of the most representative control technologies such as KNX, LonWorks and X-10. The application includes a real-time monitoring service. Finally, advanced control functionalities based on gestures recognition and predefined scenes have been implemented. This application has been developed and tested in the Energy Efficiency Research Facility located at CeDInt-UPM, where electrical loads, blinds and HVAC and lighting systems can be controlled.

Artificial Lighting as a Vector Attractant and Cause of Disease Diffusion

BACKGROUND: Traditionally, epidemiologists have considered electrification to be a positive factor. In fact, electrification and plumbing are typical initiatives that represent the integration of an isolated population into modern society, ensuring the control of pathogens and promoting public health. Nonetheless, electrification is always accompanied by night lighting that attracts insect vectors and changes people's behavior. Although this may lead to new modes of infection and increased transmission of insect-borne diseases, epidemiologists rarely consider the role of night lighting in their surveys. OBJECTIVE: We reviewed the epidemiological evidence concerning the role of lighting in the spread of vector-borne diseases to encourage other researchers to consider it in future studies. DISCUSSION: We present three infectious vector-borne diseases-Chagas, leishmaniasis, and malaria-and discuss evidence that suggests that the use of artificial lighting results in behavioral changes among human populations and changes in the prevalence of vector species and in the modes of transmission. CONCLUSION: Despite a surprising lack of studies, existing evidence supports our hypothesis that artificial lighting leads to a higher risk of infection from vector-borne diseases. We believe that this is related not only to the simple attraction of traditional vectors to light sources but also to changes in the behavior of both humans and insects that result in new modes of disease transmission. Considering the ongoing expansion of night lighting in developing countries, additional research on this subject is urgently needed.

Smart Alerts: Development of Software to Optimize Data Monitoring

Dherte PM, Negrao MPG, Mori Neto S, Holzhacker R, Shimada V, Taberner P, Carmona MJC - Smart Alerts: Development of a Software to Optimize Data Monitoring. Background and objectives: Monitoring is useful for vital follow-ups and prevention, diagnosis, and treatment of several events in anesthesia. Although alarms can be useful in monitoring they can cause dangerous user`s desensitization. The objective of this study was to describe the development of specific software to integrate intraoperative monitoring parameters generating ""smart alerts"" that can help decision making, besides indicating possible diagnosis and treatment. Methods: A system that allowed flexibility in the definition of alerts, combining individual alarms of the parameters monitored to generate a more elaborated alert system was designed. After investigating a set of smart alerts, considered relevant in the surgical environment, a prototype was designed and evaluated, and additional suggestions were implemented in the final product. To verify the occurrence of smart alerts, the system underwent testing with data previously obtained during intraoperative monitoring of 64 patients. The system allows continuous analysis of monitored parameters, verifying the occurrence of smart alerts defined in the user interface. Results: With this system a potential 92% reduction in alarms was observed. We observed that in most situations that did not generate alerts individual alarms did not represent risk to the patient. Conclusions: Implementation of software can allow integration of the data monitored and generate information, such as possible diagnosis or interventions. An expressive potential reduction in the amount of alarms during surgery was observed. Information displayed by the system can be oftentimes more useful than analysis of isolated parameters.

Innovation in Queensland firms: implications for the smart State

The challenges in the business environment are forcing Australian firms to be innovative in all their efforts to serve customers. Reflecting this need there have been several innovation policy statements both at Federal and State government level aimed at encouraging innovation in Australian industry. In particular, the innovation policy statement launched by the Queensland government in the year 2000 primarily intends building a Sman State through innovation. During the last few decades the Australian government policy on innovation has emphasized support for industry R&D. However industry stakeholders demand a more firm-focused policy of innovation. Government efforts in this direction have been hindered by a lack of a consistent body of knowledge on innovation at the firm level. In particular the Australian literature focusing on firm level antecedents of innovation is limited and fragmented. This study examines the role of learning capabilities in innovation and competitive advantage. Based on a survey of manufacturing firms in Queensland the study finds that both technological and non·technological innovations lead to competitive advantage. The findings contribute to the theory competitive advantage and firm level antecedents of innovation. Implications for firm level innovation strategies and behaviour are discussed. In addition, the findings have important implications for Queensland government's current initiatives to build a Smart State through innovation.

Lighting conditions in assembling electrical industry

Proper lighting is a prerequisite for obtaining a good working environment. Good lighting includes quantity and quality requirements, and should necessarily be appropriate to the activity/task being carried out, bearing in mind the comfort and visual efficiency of the worker. Apart from the advantages in the health and welfare for the workers, good lighting also leads to better job performance (faster), less errors, better safety, fewer accidents and less absenteeism. The overall effect is: better productivity.