Secagem de celulases de origem fúngica por spray-drying

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Secagem do resíduo industrial da acerola em leito de jorro: estudos fluidodinâmicos e análise do desempenho do secador

In this research, the drying process of acerola waste was investigated by using a spouted bed drier. The process was conducted using high density polyethylene inert particles with the objective of producing an ascorbic acid-rich final product. The fruit waste was ground and used to prepare different water-maltodextrin suspensions. Initially, fluidynamical experiments were conducted in order to evaluate the feeding effect on the spouted bed drier fluidynamics behavior. The experimental planning 23 + 3 was used to investigate the effect of the following variables: solids concentration, drying air temperature, intermittence time, production efficiency, solids retention and product losses by elutriation of fine particles on drier walls. The effect of selected independent variables on the drier stability was also evaluated based on a parameter defined as the ratio between the feed suspension volume and the total inert particles volume. Finally, the powder quality was verified in experiments with fixed feed flow and varying air drying temperature, drying air velocity and intermittence time. It was observed that the suspension interferes in the spouted bed drier fluidynamics behavior, and higher air flow is necessary to stabilize the drier. The suspension also promotes the expansion of the spouted bed diameter, decreases the solid circulation and favors the air distribution at the flush area. All variables interfere in the spouted bed performance, and the solids concentration has a major effect on the material retention and losses. The intermittence time also has great effect on the stability and material retention. When it comes to production efficiency, the main effect observed was the drying air temperature. First order models were well adjusted to retention and losses data. The acerola powder presented ascorbic acid levels around 600 to 700 mg/100g. Similar moisture and ascorbic acid levels were obtained for powders obtained by spouted bed and spray drier. However, the powder production efficiency of the spray drier was lower when compared to spouted bed drier. When it comes to energetic analysis, the spray drier process was superior. The results obtained for spouted bed drier are promising and highly dependent on the operational parameters chosen, but in general, it is inferred that this drying process is adequate for paste and suspension drying

Desenvolvimento de um secador spray para obtenção de pós finos de precursores de nióbio

This work presents a spray-dryer designed to oxalate-niobate precursors and suitable for the production of Niobium Carbide. The dryer was intended to produce powders of controlled particle size. First, the precursor is dissolved in water to produce a solution of known concentration and then it is atomized on the spray-dryer to produce the powder. This equipment consists of a 304 stainless steel chamber, 0.48 m x 1.9 m (diameter x length), with a conical shape at the lower portion, which is assembled on a vertical platform. The chamber is heated by three 4 kW electrical resistances. In this process, drying air is heated as it flows inside a serpentine surrounding the chamber, in contrary to more traditional processes in which the hot drying air is used to heat the component. The air enters the chamber at the same temperature of the chamber, thus avoiding adherence of particles on the internal surface. The low speed flow is concurrent, directed from the top to the bottom portion of the chamber. Powders are deposited on a 0.4 m diameter tray, which separates the cylindrical portion from the conical portion of the chamber. The humid air is discharged though a plug placed underneath the collecting tray. A factorial experimental planning was prepared to study the influence of five parameters (concentration, input flow, operation temperature, drying air flow and spray air flow) on the characteristics of the powders produced. Particle size distribution and shape were measured by laser granulometry and scanning electronic microscopy. Then, the powders are submitted to reaction in a CH4 / H2 atmosphere to compare the characteristics of spray-dried powders with powders synthetizided by conventional methods

Estudo da influência da proporção de um mix leite/popa da marcacujá na produção de pó obtido por três diferentes tipos de secagem

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

'Beta'-D-frutofuranosidases de Fusarium graminearum: produção, purificação, imobilização e determinação das propriedades bioquímicas de enzimas solúveis e secas em Spray dryer

Pós-graduação em Biotecnologia - IQ

Influência de encapsulantes e do método de secagem nas propriedades físico-químicas e atributos de qualidade de polpa de maracujá (Passifora edulis f. flavicarpa)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Micropartículas lipídicas sólidas obtidas por spray drying para liberação intraocular de ibuprofeno

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Micropartículas de metotrexato e ácido poli lático-co-glicólico obtidas por “spray-drying”

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Etapas do desenvolvimento de uma formulação pó molhável para o Baculovirus anticarsia: secagem e caracterização da superfície do poliedro.

As primeiras etapas selecionadas para o estudo de uma formulação pó molhável foram a caracterização de superfície quanto a morfologia (MEV) e carga, e a influencia do método de secagem na dispersibilidade das partículas. O vírus foi obtido de lagartas infectadas (CNPSo) e purificado pelo método de Van der Geest. A dispersão resultante apresenta uma distribuição de tamanho entre 1.6 e 1.9 micra, permanecendo invariável quando a preparação foi armazenada ate 6 meses sob refrigeração. O ponto isoelétrico dos poliedros de NPV de B. anticarsia, determinado a partir de gráfico de mobilidade versus pH e 4,5, sendo que em pHs superiores, as partículas estão carregadas negativamente. As dispersões foram secas por liofilização, spray dryer e estufa (27 C.). O processo de secagem determina o estado de agregação, quando os poliedros são dispersos novamente em água, com tamanho ate 27 micra, difíceis de redispersar, enquanto a secagem por spray dryer resulta em um material pouco aglomerado e facilmente dispersível.

Etapas do desenvolvimento de uma formulação pó molhável para o Baculovirus anticarsia: secagem e caracterização da superfície do poliedro.

As primeiras etapas selecionadas para o estudo de uma formulação pó molhável foram a caracterização de superfície quanto a morfologia (MEV) e carga, e a influencia do método de secagem na dispersibilidade das partículas. O vírus foi obtido de lagartas infectadas (CNPSo) e purificado pelo método de Van der Geest. A dispersão resultante apresenta uma distribuição de tamanho entre 1.6 e 1.9 micra, permanecendo invariável quando a preparação foi armazenada ate 6 meses sob refrigeração. O ponto isoelétrico dos poliedros de NPV de B. anticarsia, determinado a partir de gráfico de mobilidade versus pH e 4,5, sendo que em pHs superiores, as partículas estão carregadas negativamente. As dispersões foram secas por liofilização, spray dryer e estufa (27 C.). O processo de secagem determina o estado de agregação, quando os poliedros são dispersos novamente em água, com tamanho ate 27 micra, difíceis de redispersar, enquanto a secagem por spray dryer resulta em um material pouco aglomerado e facilmente dispersível.

Obtenção de insumo farmacêutico a partir das folhas de Cissampelos sympodialis Eichl e seu efeito sobre mediadores inflamatórios relevantes para a asma

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Dispersões sólidas de sinvastatina: preparação, caracterização, no estado sólido utilizando técnicas emergentes e estudo de estabilidade

This thesis aimed to assess the increase in solubility of simvastatin (SINV) with solid dispersions using techniques such as kneading (MA), co-solvent evaporation (ES), melting carrier (FC) and spray dryer (SD). Soluplus (SOL), PEG 6000 (PEG), PVP K-30 (PVP) e sodium lauryl sulphate (LSS) were used as carriers. The solid dispersions containing PEG [PEG-2(SD)], Soluplus [SOL-2(MA)] and sodium lauryl sulphate [LSS-2(ES)] were presented with a greater increase in solubility (5.02, 5.60 and 5.43 times respectively); analyses by ANOVA between the three groups did not present significant difference (p<0.05). In the phase solubility study, the calculation of the Gibbs free energy (ΔG) revealed that the spontaneity of solubilisation of SINV occurred in the order SOL>PEG >PVP 75%>LSS, always 80%. The phase diagrams of PEG and LSS presented solubilization stoichiometry of type 1:1 (type AL). The diagrams with PVP and SOL tend to 1:2 stoichiometry (type AL + AP). The stability coefficients (Ks) of the phase diagrams revealed that the most stable reactions occurred with LSS and PVP. The solid dispersions were characterized by Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), particle size distribution (PSD), near-infrared spectroscopy imaging (NIR-CI) and X-ray diffraction of the powder using the Topas software (PDRX-TOPAS). The solid dispersion PEG-2(SD) presented the greatest homogeneity and the lowest degree of crystallinity (18.2%). The accelerated stability study revealed that the solid dispersions are less stable than SINV, with PEG-2(SD) being the least stable, confirmed by FTIR and DSC. The analyses by PDRX-TOPAS revealed the amorphous character of the dispersions and the mechanism of increasing solubility

Suco desidratado de caju (Anacardium occidentale L.) por atomização: caracterização físico-química, bioativa e estudo da vida de prateleira do produto

Despite the relatively organized cashew (Anacardium occidentale L.) productive chain and the number of cashew derivatives found in the market, it is estimated that over 90% of the cashew peduncle is wasted. A possible strategy for a better commercial exploitation of this agroindustrial commodity would be the production of spray dried cashew pulp. Thus, this paper approaches the yellow cashew pulp spray drying process and the final product evaluation. Based on that, the shelf life of the spray dried cashew pulp packed in different packaging was evaluated. Drying was conducted in two drying temperatures (140 °C to 150 °C) and two concentrations of Arabic gum (AG, 15% and 25%), which summed four experimental groups. The drying performance was evaluated as well as the physicochemical characteristics (moisture, water activity, total soluble solids, pH, density, solubility, particle diameter, hygroscopicity, degree of caking, color, scanning electronic microscopy and X-ray diffraction), composition (protein, ash, fat and sugars) and bioactive and functional value (total phenolic compounds, carotenoids, ascorbic acid and antioxidant activity) of the final products. Results showed spray drying efficiency higher than 65% for all experiments, mainly for the C4 group (150 °C and 25% AG) which reached efficiency of 93.4%. It was also observed high solubility (94.7% to 97.9%) and the groups with lower hygroscopicity (5.8% and 6.5%) were those with the highest proportion of drying coadjuvant. The particle diameters ranged between 14.7 μm and 30.2 μm and increased with the proportion of AG. When comparing the product before and after spray drying, the drying impact was evident. However, despite the observed losses, dried yellow cashew showed high phenolic concentration (from 235.9 to 380.4 mg GAE eq / 100 g DM), carotenoids between 0.22 and 0.49 mg/100 g DM and remarkable ascorbic acid levels (852.4 to 1346.2 mg/100 g DM), in addition to antioxidant activity ranging from 12.9 to 16.4 μmol TE/ g DM. The shelf life study revealed decreased phenolic content over time associated to a slight water activity increase. Overall, our results unveil the technological and bioactive potential of dried yellow cashew as a functional ingredient to be used in food formulations or as a ready-to-use product. The technological approach presented here can serve as an efficient strategy for a rational use of the cashew apple, avoiding its current underutilization

Produção e obtenção de ciclodextrinas produzidas por CGTases bacterianas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Preparação de substratos de carbeto de silício para fins aeroespaciais

This conclusion thesis has the objective of produce substrates of Silicon Carbide from the powder of SiC for aerospace use. The powder of SiC was pressed in cylindrical form by the process called “wet way”. For the inicial pressing process was used a uniaxial squeezer and after that was used a isostatic squeezer, after that the samples were synthesized. The next step was the machining and polishing to improve the features of the surface of the sample. Then the roughness was measured, as also the Arquimedes method and optical microscopy and scanning eletron microscopy. Some innovations were done, in one of the lots little vacancys were done with organic material or silicon to reduce the weight of the sample; and the other innovation were the use of a slip film of SiC on the surface of the sample, that were after synthesized with LASER to reduce the roughness, in this samples the roughness were reduce in 50 % if compared with the other samples