Scale-up model obtained from the rheological analysis of highly concentrated emulsions prepared at three scales

We examine the scale invariants in the preparation of highly concentrated w/o emulsions at different scales and in varying conditions. The emulsions are characterized using rheological parameters, owing to their highly elastic behavior. We first construct and validate empirical models to describe the rheological properties. These models yield a reasonable prediction of experimental data. We then build an empirical scale-up model, to predict the preparation and composition conditions that have to be kept constant at each scale to prepare the same emulsion. For this purpose, three preparation scales with geometric similarity are used. The parameter N¿D^α, as a function of the stirring rate N, the scale (D, impeller diameter) and the exponent α (calculated empirically from the regression of all the experiments in the three scales), is defined as the scale invariant that needs to be optimized, once the dispersed phase of the emulsion, the surfactant concentration, and the dispersed phase addition time are set. As far as we know, no other study has obtained a scale invariant factor N¿Dα for the preparation of highly concentrated emulsions prepared at three different scales, which covers all three scales, different addition times and surfactant concentrations. The power law exponent obtained seems to indicate that the scale-up criterion for this system is the power input per unit volume (P/V).

Phase behavior and rheological analysis of reverse liquid crystals and W/I2, W/H2 gel emulsions using an amphiphilic block copolymer.

This article reports the phase behavior determi- nation of a system forming reverse liquid crystals and the formation of novel disperse systems in the two-phase region. The studied system is formed by water, cyclohexane, and Pluronic L-121, an amphiphilic block copolymer considered of special interest due to its aggregation and structural proper- ties. This system forms reverse cubic (I2) and reverse hexagonal (H2) phases at high polymer concentrations. These reverse phases are of particular interest since in the two-phase region, stable high internal phase reverse emulsions can be formed. The characterization of the I2 and H2 phases and of the derived gel emulsions was performed with small-angle X-ray scattering (SAXS) and rheometry, and the influence of temperature and water content was studied. TheH2 phase experimented a thermal transition to an I2 phase when temperature was increased, which presented an Fd3m structure. All samples showed a strong shear thinning behavior from low shear rates. The elasticmodulus (G0) in the I2 phase was around 1 order of magnitude higher than in theH2 phase. G0 was predominantly higher than the viscousmodulus (G00). In the gel emulsions,G0 was nearly frequency-independent, indicating their gel type nature. Contrarily to water-in-oil (W/O) normal emulsions, in W/I2 and W/H2 gel emulsions, G0, the complex viscosity (|η*|), and the yield stress (τ0) decreased with increasing water content, since the highly viscous microstructure of the con- tinuous phase was responsible for the high viscosity and elastic behavior of the emulsions, instead of the volumefraction of dispersed phase and droplet size. A rheological analysis, in which the cooperative flow theory, the soft glass rheology model, and the slip plane model were analyzed and compared, was performed to obtain one single model that could describe the non-Maxwellian behavior of both reverse phases and highly concentrated emulsions and to characterize their microstructure with the rheological properties.

Rheological Analysis of Water Clay Compositions in Order to Investigate Mudflows Developing in Canals

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structural carbon/epoxy prepregs properties comparison by thermal and rheological analyses

Two different carbon/epoxy prepreg materials were characterized and compared using thermal (DSC, TGA, and DMA) and rheological analyses. A prepreg system (carbon fiber preimpregnated with epoxy resin F584) that is currently used in the commercial airplane industry was compared with a prepreg system that is a prospective candidate for the same applications (carbon fiber prepreg/epoxy resin 8552). The differences in the curing kinetics mechanisms of both prepreg systems were identified through the DSC, TGA, DMA, and rheological analyses. Based on these thermal analysis techniques, it was verified that the curing of both epoxy resin systems follow a cure kinetic of n order. Even though their reaction heats were found to be slightly different, the kinetics of these systems were nevertheless very similar. The activation energies for both prepreg systems were determined by DSC analysis, using Arrhenius's method, and were found to be quite similar. DMA measurements of the cured prepregs demonstrated that they exhibited similar degrees of cure and different glass transition temperatures. Furthermore, the use of the rheological analysis revealed small differences in the gel temperatures of the two prepreg systems that were examined.

Effect of Various Thickening Agents on the Rheological Properties of Oil-in-Water Emulsions Containing Nonionic Emulsifier

The knowledge of rheological characteristics can indicate the emulsions properties, thus, nowadays rheology is used in the cosmetic and pharmaceutical industries, even to study the influence of rheological additives on them. Ten emulsions were prepared with 5% and 10% of nonionic emulsifier. Two of them were used as controls while in the others were added thickening agents. Rheological analyses were performed. The results showed that all emulsions are non-Newtonian, thixotropics and viscoelastics fluids. The thickening agents could modify the rheological characteristics of the emulsions and knowing the influence of them is easy to adopt one to reach the desirable performance. © 2013 Copyright Taylor and Francis Group, LLC.

Rheological, mechanical, and bioadhesive behavior of hydrogels to optimize skin delivery systems

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

RHEOLOGICAL EVALUATION OF THE STRUCTURE OF ICE CREAM MIXES VARYING FAT BASE

This paper discusses the influence of fat type in the structure of ice cream, during its production by means of rheo-optical analysis. Fat plays an important part in the ice cream structure formation. It's responsible for the air stabilization, flavor release, texture and melting properties. The objective of this study was to use a rheological method to predict the fat network formation in ice cream with three types of fats (hydrogenated, low trans and palm fat). The three formulations were produced using the same methodology and ratio of ingredients. Rheo-optical measurements were taken before and after the ageing process, and the maximum compression force, overrun and melting profile were calculated in the finished product. The rheological analysis showed a better response from the ageing process from the hydrogenated fat, followed by the low trans fat. The formulation with palm fat showed greater differences between the three, where through the rheological tests a weaker destabilization of the fat globule membrane by the emulsifier was suggested. The overrun, texture measurements and meltdown profile has shown the distinction on the structure formation by the hydrogenated fat from the other fats.

Rheological Properties of Organoclay Suspensions in Epoxy Network Precursors

This paper deals with the evolution of the state of dispersion of organically modified montmorillonites in epoxy or amine precursors. The epoxy prepolymer is a diglycidyl ether of bisphenol A (DGEBA) and the curing agent is an aliphatic diamine with a polyoxypropylene backbone (Jeffamine D2000). The clay dispersion is evaluated at the platelet scale (nanoscopic scale) from X-ray spectrometry [wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS)] and at the aggregates scale (microscopic scale) from rheological analysis. The organoclays used form gels in the monomers above the percolation threshold if no shear is applied and present a mechanical gel/sol transition when shear stress increases. Gel strength and viscosity at high shear rates are linked to the nanometric state of dispersion and reveal the existence of two different organizations depending on organoclay/monomer interactions: (i) When the clay shows good interactions with the monomer, a significant swelling of the clay galleries by the monomer is obtained. These swollen particles lead to formation of weak gels which after shearing give high relative viscosity fluids. (ii) When the clay develops poor interactions with the monomer, the clay tends to reduce its exchange surface with the monomer and leads to a strongly connected gel. Shear breaks down this physical network leading to a very low relative viscosity fluid composed of nonswollen particles keeping a high aspect ratio. (C) 2003 Elsevier B.V All rights reserved.

EGG ALBUMIN AND GUAR GUM INFLUENCE ON FOAM THIXOTROPY

Food foams may be defined as products containing a gaseous phase stabilized in a matrix containing water and proteins. The rheology of a foam can be altered by how the air bubbles inside are organized, its size and shape, allowing a product that was initially fluid to be molded, like marshmallow. Rheology makes possible to understand how these properties are affected using dynamic oscillatory measurements to evaluate the behavior through G` and G `, and rotational to characterize the product through stress, and viscosity curves under controlled shear stress. These two methodologies combined are useful to analyze thixotropy. Nine formulations containing albumin and gelatin, and five others containing guar gum were evaluated by oscillatory rheology focusing thixotropy determination. Replacing gelatin by guar gum elasticity and thixotropy were increased, improving film stability around the air bubbles. It is possible to say that gelatin can be replaced by guar gum at concentrations of 0.4%, creating a product with a better ability of structure recovery. PRACTICAL APPLICATION This study indicated an important role of thixotropic analysis choice to understand the behavior of structure of products like foam. It was tested with three alternatives to get information about thixotropy of the products. It is very important for those who work with rheological analysis and products formulation.

New formulation of vasoactive intestinal peptide using liposomes in hyaluronic acid gel for uveitis.

We evaluated the benefits of a novel formulation of vasoactive intestinal peptide (VIP) based on the incorporation of VIP-loaded rhodamine-conjugated liposomes (VIP-Rh-Lip) within hyaluronic acid (HA) gel (Gel-VIP-Rh-Lip) for the treatment of endotoxin-induced uveitis (EIU) in comparison with VIP-Rh-Lip alone. In vitro release study and rheological analysis showed that interactions between HA chains and liposomes resulted in increased viscosity and reinforced elasticity of the gel. In vivo a single intravitreal injection of Gel-VIP-Rh-Lip was performed in rats 7 days prior to uveitis induction by subcutaneous lipopolysaccharide injection. The maximal ocular inflammation occurs within 16-24 h in controls (VIP-Rh-Lip, unloaded-Rh-Lip). Whereas intraocular injection of VIP-Rh-Lip had no effect on EIU severity compared with controls, Gel-VIP-Rh-Lip reduced significantly the clinical score and number of inflammatory cells infiltrating the eye. The fate of liposomes, VIP and HA in the eyes, regional and inguinal lymph nodes and spleen was analyzed by immunostaining and fluorescence microscopy. Retention of liposomes by HA gel was observed in vitro and in vivo. Inflammation severity seemed to impact on system stability resulting in the delayed release of VIP. Thus, HA gel containing VIP-Rh-Lip is an efficient strategy to obtain a sustained delivery of VIP in ocular and lymph node tissues.

Facile bisurethane supramolecular polymers containing flexible alicyclic receptor units

This paper details the synthesis, characterisation and physical analyses of a series of hydrogen bonded urethane supramolecular polymer systems that are created by a facile one-step synthesis from inexpensive and commercially available starting materials. We report the synthesis and characterisation of a series of low molecular weight bisurethanes (<650 a.m.u.) that exhibit physical properties in the bulk that are characteristic of polyurethane materials possessing far higher molecular weight. The physical characteristics of these low molecular weight bisurethanes were investigated by using temperature-dependent rheological analysis and viscometry and the nature in which these compounds assembled was assessed using IR and NMR spectroscopies. These studies reveal that these simple bisurethanes self-assemble via hydrogen bonding interactions.

Thermally responsive elastomeric supramolecular polymers featuring flexible aliphatic hydrogen-bonding end-groups

The present paper details the synthesis, characterization, and preliminary physical analyses of a series of polyisobutylene derivatives featuring urethane and urea end-groups that enable supramolecular network formation to occur via hydrogen bonding. These polymers are readily accessible from relatively inexpensive and commercially available starting materials using a simple two-step synthetic approach. In the bulk, these supramolecular networks were found to possess thermoreversible and elastomeric characteristics as determined by temperature-dependent rheological analysis. These thermoreversible and elastomeric properties make these supramolecular materials potentially very useful in applications such as adhesives and healable surface coatings.